GE ZV830SM2SS, ZV830SM1SS Owner’s Manual

Own r's

Manual

30" Chimneg Vent Hood

For Model:

ZV830

30" (76,2cm)

Hotte aspirante

Manuel du propri_taire

Pour la ModUles :

ZV830

La section frangaise commence 6 ta page 17

Campana de ventilaci6n de chimenea de 30" (76,2 cm)

Manual del propietario

Para Hodelo:

ZV830

La secci6n en espafiol empieza en la p6gina 29

49-80513 ] 01-08]R

Consumer Information

Chimney Hood

Introduction

Contents

Your new Monogram chimney hood makes an eloquent statement of style and design. Whether gou chose it for its puritg of design, assiduous attention to detail-or for both of these reasons-gou'll find that your Monogram chimney hood's superior blend of form and function will delight 9ou for gears

to come.

Your Monogram chimney hood was designed to be elegant, get provide the venting performance 9ou need when cooking. Its sleek design can be beautifull 9 integrated into the kitchen.

The information on the following pages will help 9ou operate and maintain gour chimney hood properlg.

Consumer Information

Important Phone Numbers .................... 15

Model and Serial Numbers ...................... 2

Problem Solver ............................... 8, 9

Product Registration ....................... 11-14

Safetg Instructions .............................. 4

Warrantg ...................................... 16

Controls and Features ......................... 5

Care and Cleaning

Charcoal Filter .................................. 7

Filter Panel ...................................... 6

Light Bulbs ...................................... 7

Metal Grease Filter .............................. 6

StainlessSteel Hood Surfaces ................... 7

Before using gour

chimneg

hood

Write down the model & serial numbers

Readthis manual carefullg. It is intended to help gou operate and maintain gour new chimneg hood properlg.

Keep it handg for answers to gour questions.

You'llfind them on a label on the hood. These numbers are also on the Consumer Product

Ownership Registration Card packed separatelg

with gour hood.

Visit monogram.corn and click on "RegisterYour Appliance" to register gour chimneg hood.

If gou don't understand something or need more help, there is a list of toll-free consumer service

numbers included in the back section of this manual.

OR Visit our Website at: monogram.corn

Before sending in this card, please write these numbers here:

Hodel Number

Serial Number Use these numbers in ang correspondence or

service calls concerning gour hood.

If gou received a

damaged hood

Immediatelg contact the dealer (or builder) that sold gou the hood.

Consumer Information

Chimney Hood

Save time & moneg

If gou need

service

Before gou request service, check the Problem Solver in the back of this manual.

Toobtain service, see the Consumer Servicespage in the back of this manual.

We're proud of our service and want gou to be

pleased. If for some reason gou are not happg with the service gou receive,here are some steps to follow for further help.

FIRST,contact the people who serviced gour appliance. Explainwhg gou are not pleased. In most cases,this will solvethe problem.

It lists causes of minor operating problems that 9ou can correct goursel£

NEXT,if gou are still not pleased,write allthe details-including gour phone number-to:

Manager, Customer Relations GEAppliances Appliance Park

Louisville,KY40225

READ ALL INSTRUCTIONS BEFORE USING

SAFETY PRECAUTIONS

IllA Ol_lll_lt _

VV/_I_I_I I I_I_--TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit onlg in the manner intended

bg the manufacturen If gou have questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch

power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentallg. When the service disconnecting means cannot be locked, securelg fasten a prominent warning device, such as a tag, to the service panel.

C. Do not use this unit with ang solid-state speed

control device.

D. This unit must be grounded.

CAUTION-FoRGENERALVENTILATING

USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.

W/_I_I_I I I_Iti._--TO REDUCE THE RISK OF

INJURY TO PERSONS IN THE EVENT OFA RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

A. SMOTHER FLAMES with a close-fitting lid,

cookie sheet or metal tray, then turn off the burnen BE CAREFUL TO PREVENT BURNS. If the

flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVERPICKUPA FLAMINGPAN--You mag be

burned.

C. DO NOT USE WATER, including wet dishcloths

or towels-a violent steam explosion will result.

D. Use on extinguisher ONLY if:

1. You know gou have a Class ABC extinguisher, and you alread 9 know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with gour back to an exit.

*Based on "Kitchen Firesafetq Tips" published bg

NFPA.

READ AND SAVE THESE INSTRUCTIONS.

IMPORTANT SAFETY INSTRUCTIONS

VV/_I_I_I I I_Iti.I--TO REDUCE THE RISK OF A

RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high

settings. Boilovers cause smoking and greasg spillovers that mag ignite. Heat oils slowly an

low or medium settings.

B. Alwags turn hood ON when cooking at high

heat or when flamb&ing food {i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef

Flamb6).

C. Clean ventilating fans frequentlg. Grease

should not be allowed to accumulate on fan or filter.

D. Use proper pan size. Alwags use cookware

appropriate for the sizeof the surface element.

I 1/AI_I_I I I_lt"

VV/_I_I_I I I_I_--TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done bg qualified person(s} in accordance with all applicable codes and standards, including

fire-related construction.

B. Sufficient air is needed for proper combustion

and exhausting of gases through the flue (chimneg) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer's guidelines and safetg standards such as those published bg

the National Fire Protection Association {NFPA),

and the American Societg for Heating, Refrigeration and Air Conditioning Engineers

{ASHRAE},and the local code authorities.

C. When cutting or drilling into wall or ceiling, do

not damage electrical wiring and other hidden utilities.

D. Ducted fans must alwags be vented to the

outdoors.

W/_I_I_I I I_I_--TO REDUCE THE RISK OF

FIRE, USE ONLY METAL DUCTWORK.

• DO not attempt to repair or replace ang part of gour hood unless it is specificallg

recommended in this manual. All other servicing should be referred to a qualified

technician.

CAUTION-AuTOMATICALLY OPERATED

DEVICE. TO REDUCE THE RISK OF INJURY, DISCONNECT FROM POWER SUPPLY BEFORE

SERVICING. THE UNIT IS EQUIPPED WITH AN

INTEGRAL DISCONNECTING SWITCH LOCATED INSIDE THE BLOWER HOUSING.

Controls

FAN

Controls and Features

Chimneg Hood

LIGHT

MEMORY/OFF

-- ,I,

5 4

1 MEMORY/OFF Button. Press to recall

memorized fan and light settings. To memorize desired fan and light settings:

1. Press the MEMORY/OFF button.

2. Select desired settings.

3. Press MEMORY/OFF to save. The hood will now turn off and the settings will

be memorized.

NOTES:

• When ang button is active {turned on), all outer rings will be illuminated.

• The hood can be turned OFF at ang time bg pressing the MEMORY/OFF button.

-- 4"

()

3 2

BOOST--Provides five minutes at the maximum

fan setting and then automaticallg resets fan to HIGH.

NOTE: BOOST can stag on longer than five

minutes when activated bg the auto sensor

AUTOMATICFAN FEATURE--Thehood fan

will turn on automatically or automatically increase in speed if cooking temperatures

become too hot, Thefan will turn off automoticollg or decrease in speed when

temperatures cool to an appropriate level

NOTE: When the automatic feature is on, gou can set the fan to a higher setting but not to a lower setting or off.

• Alwags deactivate {turn off} the buttons when the hood is not in use.

2 LIGHT INCREASE ON/OFF Button, Press to turn

on or increase light level. The buttons allow gou to cgcle to the desired setting. (There are four light levels/settings and OFF)

3 LIGHT DECREASE ON/OFF Button. Press to turn

on or decrease light level. The buttons allow gou to cgcle to the desired setting. {There are four light levels/settings and OFF.)

4 FAN INCREASE ON/OFF Button, Press to turn

on or increase fan settings. The buttons allow gou to cgcle to the desired setting. {Use to set

the fan speed to LOW, MED, HIGH, BOOSTor OFF.)

5 FAN DECREASE ON/OFF Button. Press to turn

on or decrease fan settings. The buttons allow gou to cgcle to the desired setting. {Use to set

the fan speed to LOW, MED, HIGH, BOOSTor OFF.}

Careand Cleaning

Chimney Hood

For gour safetg

Filter panel

Metal grease

filter

Beforeservicingor cleaningthe unit, switch power off at the servicepanel and lockthe servicepanel to prevent power from beingswitched on accidentallg. If the servicepanel cannot be locked,fasten a tag or prominent warning label to the panel.

Greasewill accumulate on the filter panel.The panel isdishwasher-safeand should be cleanedeverg 6

months or as needed.

1. Pressin to releaseand lowerthe filter cover panel.

2. Removethe hinge barrel nuts and screws on both sides.Shift filter panel to the left and

remove.

3. Stand the filter cover panel in the dishwasher

with the drain holesfacing the bottom.

NOTE:The filter must ALWAYSbe in place and the filter panel must ALWAYSbe closedwhen the hood

is in use.

Themetal filter traps grease released bg foods from the cooktop. Thefilter also helps prevent flames (from food, grease}from damaging the

inside of the hood. Forthis reason, the filter must ALWAYSbe in place

and the filter panel must ALWAYSbe closedwhen the hood is in use.Thegrease filter is dishwasher- safe and should be cleaned everg 6 months, or

as needed.

ooooo

Presscorners

tounlock,

Barrel nut (2)

Filterpanel

Presscorners

To remove:

1. Pressup on the front two corners of the filter cover panel to unlock. Lower the panel to access

the filter.

2. Pressthe filter latch in to releaseit. Pullthe filter down and out.

To replace:

1. Placethe two tabs onthe filter edge into the lower locating slots in the left or right side of the hood opening.

2. Pushthe filter up and snap it into place in

the hood.

3. Rotatethefilter coverpanelup into positionand pressup on itsfront two cornersto lock itinto place.

Toclean, swish the filter in hot soapg water and rinse in clean water or wash it in the dishwasher.

Do not useabrasive cleansers. NOTE:Some discoloration will occur in the

dishwasher.

Careand Cleaning

Chimney Hood

Charcoal filter

(on some models)

Stainless steel hood surfaces

If the model is not vented to the outside, the air will be recirculated through a disposable charcoal filter that helps remove smoke and odors.

Thecharcoal filter should be replaced when it is noticeabl 9 dirty or discolored (usually after 6 to 12

months, depending on hood usage). NOTE:DO NOTrinse,or put charcoal filter in an

automatic dishwasher. The charcoal filter cannot be cleaned. It must be

replaced.

Order Charcoal Filter WBO2X11342. Toinquire about purchasing replacement charcoal

filters or to find the location of a dealer nearest _tou, pleasecall our toll-free number:

National Parts Center 800.626.2002

Regularlg polish the stainlesssteel exterior

with StainlessSteelHagid" and the Honogram

polishing cloth, to preserve and protect the fine finish.

To avoid scratching the fine finish of the stainless steel, wipe in the same direction as the

grain when polishing or cleaning any stainless steel surface.

For regular cleaning, use clean water and a soft cloth, if stains persist, wash with mild dish soap using asoft cloth or nonabrasive pad. For more difficult stains, make a solution consisting of 25% vinegar (white or red) and 75% waten Dip

a soft cloth into the solution and rub onto the stainless steel to remove the stain. If these methods do not remove the stains, dirt or

debris, call 800.GECARES.

To remove:

1. Remove the metal filter-see Metal grease filter section.

2. Remove the charcoal filter in the same manner as the metal grease filter bg pressing the filter

latch in to release it. Pull the filter down and out.

To replace:

1. Insert the black charcoal filter into the opening. Push the latch on both sides toward the center

and engage the flange.

2. Replace the metal filter-see Metal grease filter section.

NOTE:Reapply StainlessSteelHagic with the Honogram polishing cloth after cleaning or if your

unit comes in contact with water, to protect the fine finish.

StainlessSteel Hagic and the Honogram polishing cloth are available through GEPartsand

Accessories,800.626.2002 or monogram.com. For StainlessSteelHagic, order part number

WXIOX15.

Do not use appliance wax or polish on ang stainless steel surface.

Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because

these products can scratch and damage the finish.

Warrantg does not cover damage due to improper cleaning methods.

Light bulbs

CAUTION: Allow bulbs to cool before

touching. To change the light bulbs:

1. Pressand turn the light bulb face 1/4 turn.

2.The bulbwill drop straight out. & Replacewith the same size bulb bg placing bulb

prongs into the keghole slots and turning 1/4

turn to lockin place.

These 120 volt, 50watt, MR16 halogen bulbs

with GU10bases are available at most specialtg

lighting stores, building centers and large retailers.Ask for MR16 GUIObase bulb.

NOTE:Do not replace with bulbs greater than 120volts, SOwatts, or the lights will automatically shut off and the rings around the operating buttons will flash to indicate the bulbs have exceeded the acceptable limits.

The Problem Solver

Chimneg Hood

Questions?

Use this

problem solver!

PROBLEM POSSIBLE CAUSE FAN AUTOMATICALLY

TURNS ON OR INCREASES IN SPEED AND CAN NOT BE TURNED OFF OR LOWERED IN SPEED

FAN DOES NOT OPERATE WHEN TURNED ON

The hood fan will turn on automatically or automatically increase in speed if cooking temperatures become too hot. The fan will turn off automatically or decrease in speed when temperatures cool to an appropriate level. Fan will also turn on automatically when the hood

electronics are too hot. NOTE: When the automatic fan feature is on, you can set the fan to

a higher setting but not to a lower setting or off. A fuse may be blown or a circuit breaker tripped. Replace fuse or

reset circuit breaken

The power disconnect switch inside the hood may be switched of/ Remove the metal grease filter and the charcoal filter (if present} and flip the switch on.

LOCATE ON/OFF SWITCH.

1. Press in to release and lower the filter cover panel at the front.

2. Pushthe filter latch toward the opening and pull downward to remove.

3. Remove the charcoal filter, if present.

<.o

Presscorners

4. Reach into the motor compartment and locate the ON/OFF switch at the front of the opening.

S. Press switch to ON position.

Filtel latch

Push-bu_on

switch

(horizontal

view from

inside

opening)

NOTE:If the hood blower needs to be removed for service, use the disconnect switch for your safety. Pressthe switch to the OFFposition.

The Problem Solver

Chimney Hood

Questions? Use this

problem solver!

PROBLEM FAN FALLS TO CIRCULATE

AIR OR MOVES AIR SLOWER THAN NORMAL

FAN KEEPS GOING OFF AND ON

LIGHTS WILL NOT WORK AND RINGS AROUND THE

OPERATING BUTTONS ARE FLASHING

LIGHT WILL NOT STAY ON HIGH SETTING

THE HOOD CONTROLS ARE NOT OPERATING

CORRECTLY

POSSIBLE CAUSE

Check to be sure the metal grease filter and the charcoal filter (if present) are clean. Clean the metal grease filter (see the Metal grease filter section) and, if the hood is recirculated {not vented to the outside), replace the charcoal filter (see the Charcoal filter section). If cleaning and replacing the filters does not correctthe problem,

call for service. The motor is probablg overheating and turning itself off. This can

be harmful to the motor. Check to be sure the filter is clean and check ductwork for blockage. If off and on cgcling continues, call

for service.

• Light(s/were replaced with bulbs with greater than the 120 volt, 50 watt limit. Replace with the correct tgpe and size bulb. See the

Light bulbs section.

Use 120 volt, 50 watt, MR16 halogen bulbs with a GUIO base and make sure theg are inserted securelg. It is important to replace with bulbs that do not exceed the recommended wattage. Higher wattage bulbs will cause the outer rings to blink, and the lights will not function at the highest levels. See the Light bulbs section.

Disconnect power to the hood bg turning the circuit breaker off or bg removing the fuse in the home fuse box. Wait 30 seconds to allow the hood controls to reset and then replace the fuse or move the circuit

breaker back on.

SEQUENTIAL PRESSES OFTHE LIGHT OR FAN

BUTTONS WILL CHANGE THE SETTING FROM THE

LOWEST SETTING TO OFF TO THE HIGHEST SETTING,

OR FROM THE HIGHEST SETTING TO OFF TO THE

LOWEST SETTING WHEN PRESSING THE

MEMORY/OFF BUTTON TO TURN ON THE LIGHT,

THE FAN COMES ON INSTEAD

So that gou can easil9 set the controls to the desired setting, the hood is designed for the light and fan buttons to cgcle through the settings.

This is normal.

For gour convenience, it is normal for the lights and fan to remember their last setting when gou press the Memorg/Off button. If gou want anlg the lights an, press the "FAN +" (or the "FAN -" ) button to turn the fan off. When gou power the hood up next time, onlg the lights will function. NOTE: You mag turn the fan and lights off or on separatelg, using the "+" or "-" buttons.

Notes

Chimneg Hood

fiopo.i.I!O_ _UD_JOdLUl

UO!:lOJ_S!6aEl d!LISJaUMO

:[:)npoJd Jawnsuo3

saouo!lddv 99

General Electric Company Warranty Registration Department

P.O.Box 32150 Louisville, KY40232-2150

IIIII P,oce

1st Class Letter

Stamp

Here

Consumer Product Ownership Registration

Dear Customer: Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to

have you as a customer!

Follow these three steps to protect gour new appliance investment:

Complete and mail gour Consumer

Product Ownership Registration todeg.

Have the peace of mind of knowing we can

contact you in the unlikely event of a

safety modification.

Important: To ensure that gour product is registered, mail the separate product registration card.

If the separate product registration card is missing, fold and mail the form below. No envelope is needed.

After completing this

registration, write gour model and serial

numbers in this manual,

You will need this

information should you require service.

Our service number

is800,4Lt4.1845.

FOLD HERE

Read your Owner's

Manual carefullg. Itwill help you operate your

new appliance properly.

Consumer Product Ownership Registration

_ Product Model Serial

Mr Mrs MS [ i Miss [ i

FirstI ILastI

Name I I I I I I I I I Name I I I I I I I I I I I I I

Hood

StreetI I

Address IIIIIIIIIIIIIIIIIIIIIIIIII

Apt. # I I I

CRy I I I

Dote Placed

In Use I I I

Month

GE Consumer & Industrial Appliances

General Electric Compong Louisville, KY/40225

moRogl-arri.com

Appliances

e_ GEConsumer&Industrial

. monogramcorn

GeneralElectricCompang Louisville,KY/40225

,,,,,IE-ma, Address*l,,,,,,,,,,,,,,I

IIIIIIIIIIIIIIState Code llll

I I, IZipI I

Dayl, I Yeorl, I NumberPh°neI , , I-I , , I-I , , , I

* Please provide gout e-moil addless to receivei via e-mail, discountsi special offers and other important

communications flora GEAppliances {GEA} Check here if 9ou do not want to receive communications flom GEA's corefu]]g selected partners

FAILURETOCOMPLETEAND RETURNTHIS CARDDOES NOT DIMINISH YOURWARRANTYRIGHTS

For more information about GEA's privocg and data usage polic9, go to monogrorn cam end dick on "Pnvocg Policg" or call 800626222/4

TAPE CLOSED

J_2

+ 28 hidden pages