GE ZISB480DX User Manual

Page 1
*84"
(213.4)
48" (121.9)
1 3/4"
(4.4)
*72 1/4"
(183.5)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
13 1/2"
(34.3)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
(9.5)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
OVERALL DIMENSIONS
48" (121.9)
13 1/2"
(34.3)
1 3/4"
(4.4)
ZISB480DXGE Monogram® 48" Built-In Side-by-Side Refrigerator
SPECIFICATIONS
Overall Width 48" (121.92 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/8" (64.453 cm)
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 47 1/2" (120.7 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE SmartConnect kit
Shipping Weight 775 lb
*84"
(213.4)
*72 1/4"
(183.5)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
(9.5)
* Shipping height . Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
47" (119.4)
Case width
** Allow 15" (38.1) min clearance for 130˚ door swing
*3 1/2"
(8.9)
** Allow 20" (50.8) min clearance for 130˚ door swing
SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
28 5/8"
(72.7)
TOP VIEW
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow full 130° door swings for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimension may vary due to manufacturing tolerances.
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
Product Specification Created 3/14
Page 2
GE Monogram® 48" Built-In Side-by-Side Refrigerator
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 ) From floor to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB480DX
STANDARD INSTALLATION
*83 1/2" min
*84 1/2" max
*Trim will overlap
additional 7/16"
(212.1-214.6)
ANTI-TIP BRACKET
C
SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
(15.2)
5"
(12.7)
47 1/2" (120.7)
A
6"
(12.7)
3 1/4"
20" (50.8)
(8.3)
E
From floor to bottom
of electrical
3 1/2"
(8.9)
75"
(190.5 )
area
5"
B
5"
(12.7)
24" (61.0)
1 1/2"
(3.8)
WATER
FRONT VIEW SIDE VIEW
D
*84"
(213.4)
*Or installation
height from floor
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
Screws mounted
into vertical wall
The refrigerator will project forward, slightly beyond adjacent cabinetry.
2" x 4"
Cut to 35" Length
studs
Top Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
W
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
Side View Top
Case Trim
E
3/4" Min.
NOTES
A
Mounting the junction
box in this location will also allow for front accessability through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
The information below is for cabinet design only.
When installing the anti­tip system you must use the product installation instructions.
Determine your installation construction and required anti-tip configuration:
C
Installed Under Soffit
After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exeed 24” deep. The top case trim overlaps the bottom of the soffit.
D
Wooden Wall Studs and
No Soffit
• Cut a 2” x 4” block and secure to brackets provided.
• Secure brackets to back wall of opening at 84” or your installation height from the floor.
E
Metal Wall Studs and
No Soffit
This method requires securely fastened cabinets on both sides and a ¾” minimum wood brace above unit, with it’s front surface 24” from back wall.
• After installing unit into opening, raise grille panel and attach metal case top trim to ¾” minimum wood brace.
• The brace spanning the enclosure must be securely fastened to cabinets on both sides.
See Installation Instructions for detailed instructions.
Product Specification Created 3/14
Page 3
GE Monogram® 48" Built-In Side-by-Side Refrigerator ZISB480DX
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
*84
*84"
(213.4)
(213.4)
*Depending
*Depending
on installation
on installation
height
NOTES
F
Side panels must be
used whenever the sides of the refrigerator will be exposed. The 1/4” side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.
2 9/16"
(6.5)
Product Specification Created 3/14
Page 4
1/4" Framed Panel
A
GE Monogram® 48" Built-In Side-by-Side Refrigerator ZISB480DX
(24.4)
15 3/8"
(24.4)
15 3/8"
1/4" FRAMED PANEL DIMENSIONS
PANEL ASSEMBLY CROSS SECTION
Grille Panel
D E
Dispenser
Cutout
F
B
PANEL DIMENSIONS
G
Freezer
Panel
C
Fresh Food Panel
1/4" Framed Panel
Dispenser
Cutout
9 5/8"
Trim
A B C D E
45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"
Door
Supplied Handles
DISPENSER CUTOUT
(39.1)
POSITION
F G
17 13/16" 5 1/8"
NOTES
Trimmed refrigerators are designed to be customized with decorative panels. Field­installed custom door and grille panels are required.
1/4” Framed Panels:
You may install 1/4"- thick custom panels from your cabinet manufacturer. The decorative panels slide into the factory- installed trim.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
3/4" OVERLAY PANEL DIMENSIONS
A
Grille Panel
D E
G
F
Fresh Food Panel
Dispenser
Cutout
Freezer
Panel
3/4” Overlay Panels:
For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a
PANEL ASSEMBLY CROSS SECTION
B
1/4" Backer Panel
.10" Spacer Panel
Trim
Door
3/4" Overlay Panel
Supplied Handles
PANEL DIMENSIONS
A B C D E
C
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
.25" + .10" + .75" = 1.10" Total Panel Thickness
45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"
45" 8 5/8" 67" 17 1/4" 25 1/4"
46 1/8" 9 3/4" 68 5/8" 18 13/16" 26 13/16"
* DISPENSER CUTOUT
Dispenser
Cutout
9 5/8"
(39.1)
POSITION
F G
17 15/16" 5 1/4"
* Cut the dispenser opening after the backer, spacer
and overlay panels have been assembled.
1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.
Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles:
The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels.
Kits include one handle. Order 2 kits for side­by-side refrigerators from your Monogram suppplier.
Product Specification Created 3/14
Page 5
GE Monogram® 48" Built-In Side-by-Side Refrigerator ZISB480DX
DISPENSER TRIM
1/4" Framed Panel
Freezer Door
Ice/Water Dispenser
1/4"
Total
Thickness
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
Freezer Door
Ice/Water Dispenser
1/4" PANEL DISPENSER TRIM 3/4" OVERLAY PANEL DISPENSER TRIM
A B
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS
1/4" Backer Panel .10" Spacer
3/4" Overlay Panel
16 3/4"
1.10”
Total
C
10 5/8"
Thickness
D
1.10"
Total
Thickness
NOTES
These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels.
1/4" Panel Dispenser Trim:
A
The framed panel must be 1/4” nominal thickness to fit the dispenser trim.
• The dispenser trim fits over the custom panel and snaps into the freezer door.
• If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.
• If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door.
3/4" Overlay Panel Dispenser Trim:
B
The 3/4” overlay dispenser trim is designed to fit a total panel thickness of
1.100".
• If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim.
• If the panel is more than 1.100" thick, the dispenser trim cannot be secured to the door.
DISPENSER TRIM
SIDE VIEW CROSS SECTION
(Showing Raised Overlay
with Middle Rail)
• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.
• Alternative panel construction methods
such as securing a 3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required
1.100" panel thickness.
• When a raised panel design is to be used, a custom middle rail is required.
Raised Overlay Panel Design on Dispenser Models:
When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.
• The middle rail must be wide enough to
C
allow for the dispenser trim to overlap the opening.
• The middle rail must be 1.10” total
D
thickness to accept the dispenser trim.
Product Specification Created 3/14
Page 6
GE Monogram® 48" Built-In Side-by-Side Refrigerator ZISB480DX
FEATURES AND BENEFITS
Halogen Light Columns - Located in the freezer
and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination
LED Lighting - Located at the top of the fresh food compartment, and inside the vegetable and climate-control drawers, illuminates contents without compromising space
Advanced Temperature Management System with Multi-Shelf Air Tower - Provides even
distribution of air throughout the refrigerator
Climate-Control Drawer - Allows you to express­chill beverages, express-thaw meats and select specific temperatures for perishable foods
Dispenser with Proximity Sensor - Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away
Dairy Bin with Center Divider - Has a unique magnetic seal that locks in freshness
Filter-Change Indicator Light - Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser
®
Water Filter - Has been moved from the
GE
fresh food compartment to the overhead cabinet, where it is discreetly out of sight
Drop-Down Shelf - Provides additional space for a casserole dish or pizza box
R
Product Specification Created 3/14
Loading...