GE ZISB420DH User Manual

Page 1
SECTION 1
FLUSH INSET INSTALLATION
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
SECTION 2
STANDARD INSTALLATION
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
Product Specification Revised 10/14
Page 2
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
SPECIFICATIONS
Overall Width 44" (111.8 cm)
Overall Height 83 1/2" (212.1 cm)
Overall Depth 25 7/8" (65.7 cm)
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 45" (114.3 cm)
Cutout Height 84 1/2" (214.6 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE SmartConnect kit
Shipping Weight 725 lb (328.9 kg)
OVERALL DIMENSIONS
FLUSH INSET INSTALLATION
25 7/8" (65.7)
*3"
(7.6)
20 5/8" (52.4)
* 83 1/2"
(212.1)
SIDE VIEW
44" (111.8)
11 5/16"
(28.7)
13 1/2"
(34.3)
*72 3/16"
(183.4)
*83 1/2"
(212.1)
68 13/16"
(174.8)
*40"
(101.6)
FRONT VIEW
*3 3/8"
(8.6)
* Shipping height . Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84".
41" (104.2)
Case width
**13"
(33.0)
**15"
(38.1)
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
*115° Door swing
Doors can be adjusted to
90° door swing
26 5/8"
(67.6)
TOP VIEW
** Allow 4" (10.2) min clearance to a wall for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
** Allow 4" (10.2) min clearance to a wall for 90˚ door swing
Product Specification Revised 10/14
Page 3
FRONT VIEWSIDE VIEW
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 ) From floor to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
FLUSH INSET INSTALLATION 3/4" PANELS
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
84 1/2"
(214.6)
Finished cleats
W
ANTI-TIP BRACKET
C
SOFFIT
3 1/2"
(8.9)
Width of side cleats
5 1/4" (13.3)
3/4" (1.9)
84 1/2"
(214.6)
D
TOP VIEW
Finished cleats
Case Trim
3/4" Panel
(15.2)
7"
(17.8)
*Or installation
height from floor
Case
Door
45" (114.3) Flush inset width
43 1/2" (110.5)
Width between cleats
6"
E
5"
(12.7)
WATER
2" x 4"
Cut to 35" Length
Screws mounted into vertical wall
studs
*84"
(213.4)
FLUSH INSET INSTALLATION
NOTES
A
1/2" (1.3)
A
19"
(48.3)
75"
(190.5 ) From floor to bottom
of electrical
area
7"
(17.8)
3 1/2"
(8.9)
B
Mounting the junction
box in this location will also allow for front accessability through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
The information below is for cabinet design only.
When installing the anti­tip system you must use the product installation instructions.
Determine your installation construction and required anti-tip configuration:
C
Cut a 1/2” x 4” block 35”
long. Measure and mark under the soffit, 5 1/4” from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84”.
D
Wooden Wall Studs and
No Soffit
• Cut a 2” x 4” block and
secure to brackets provided.
• Secure brackets to back
wall of opening at 84” or your installation height from the floor.
See Installation Instructions for detailed instructions.
SIDE VIEW INSTALLED
UNDER SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
Product Specification Revised 10/14
Page 4
(24.4)
15 3/8"
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
FLUSH INSET 3/4" PANEL DIMENSIONS
Grille Panel
D E
Dispenser
Cutout
F
A
B
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
HINGE CLEARANCES
G
Freezer
Panel
Fresh
Food
Panel
C
Z
PANEL DIMENSIONS
A B C D E
44" 10 5/8" 68 13/16" 16 7/8" 26 7/8"
1/4" Router Cut Depth for Hinge Clearance
Door
ROUTER 1/4" DEEP
Y
FLUSH INSET INSTALLATION
NOTES
Trimmed refrigerators are designed to be customized with decorative panels. Field­installed 3/4” custom door and grille panels are required. Adjustment brackets allow 1/8” fine adjustment of panel position in 3 dimensions. Use templates provided to locate mounting brackets on the door and grille panels.
Maximum total panel weight:
HINGE CLEARANCE
X Y Z
X
1 1/4" 1" 1/2"
• Fresh food door panels – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles
Door handle not included. A custom handle supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4” panels. Kit includes
one handle – 30 1/2” long.
ZKHSS2: European tubular stainless steel handle designed to fit 3/4” panels. Kit includes
one handle – 64 1/4” long.
Dispenser
Cutout
9 5/8"
(39.1)
DISPENSER CUTOUT POSITION
F G
18" 3 7/16"
Product Specification Revised 10/14
Page 5
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
DISPENSER TRIM
Freezer Door
Ice/Water Dispenser
3/4" Flush Panel
3/4" OVERLAY PANEL DISPENSER TRIM
A
RAISED PANEL DESIGN ON DISPENSER MODELS
16 3/4"
10 5/8"
3/4" Flush Panel
B
3/4"
Total
Thickness
C
FLUSH INSET INSTALLATION
NOTES
These refrigerators are supplied with a dispenser trim for flush inset panels.
A
3/4" Panel Dispenser Trim:
The provided dispenser trim is designed to fit a total panel thickness of 3/4".
• If the panel is less than 3/4" thick, a
noticeable gap may be created around the dispenser trim.
• If the panel is more than 3/4" thick, the
dispenser trim cannot be secured to the door.
• The overlay panel must be constructed
according to the specifications shown to achieve the correct total thickness.
• When a raised panel design is to be used, a
custom middle rail is required.
Raised Panel Design on Dispenser Models:
When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.
B
• The middle rail must be wide enough to
allow for the dispenser trim to overlap the opening.
C
• The middle rail must be 3/4” total
thickness to accept the dispenser trim.
DISPENSER TRIM
SIDE VIEW CROSS SECTION (Showing Raised Panel with
Middle Rail)
Product Specification Revised 10/14
Page 6
*84"
(213.4)
42" (106.7)
25 1/2" (64.8)
23 7/8" (60.7)
1 3/4"
(4.4)
*72 1/4"
(183.5)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
13 1/2"
(34.3)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
(9.5)
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
SPECIFICATIONS
Overall Width 42" (106.7 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/8" (64.453 cm)
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 41 1/2" (105.4 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE SmartConnect kit
Shipping Weight 725 lb (328.9 kg)
OVERALL DIMENSIONS
STANDARD INSTALLATION
42" (106.7)
13 1/2"
(34.3)
*84"
(213.4)
(9.5)
*72 1/4"
(183.5)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
* Shipping height . Use leveling legs and wheels for maximum 1" height adjustment from shipping height.
41" (104.2)
Case width
** Allow 13" (33.0) min clearance for 130˚ door swing
25 1/2" (64.8)
23 7/8" (60.7)
1 3/4"
(4.4)
*3 1/2"
(8.9)
** Allow 19" (48.3) min clearance for 130˚ door swing
SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply is required. An inidividual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall.
26 5/8"
(67.6)
TOP VIEW
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow full 130° door swings for pan removal. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted. Actual product dimensions may vary due to manufacturing tolerances.
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
Product Specification Revised 10/14
Page 7
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
STANDARD INSTALLATION
3 1/8"
(7.93)
SIDE VIEW
24" (61)
1 9/16"
(3.97)
ANTI-TIP BRACKET
C
SOFFIT
SIDE VIEW INSTALLED
UNDER SOFFIT
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
*84 1/2"
*Trim will overlap
additional 7/16"
(214.6)
D
*Or installation
height from floor
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
TOP VIEW
41 1/2" (105.4)
A
6"
(15.24)
5"
(12.7)
WATERW
FRONT VIEW
2" x 4"
Cut to 35" Length
Screws mounted into vertical wall
studs
*84"
(213.4)
20" (50.8)
E
5"
(12.7)
75"
(190.5 ) From floor to bottom
of electrical
area
3 1/2"
5"
(8.9)
(12.7)
B
Top Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
The refrigerator will project forward, slightly beyond adjacent cabinetry.
E
3/4" Min.
Side View Top
Case Trim
STANDARD INSTALLATION
NOTES
A
Mounting the junction
box in this location will also allow for front accessability through access panel.
B
Water supply area.
WARNING:
The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.
The information below is for cabinet design only.
When installing the anti­tip system you must use the product installation instructions.
Determine your installation construction and required anti-tip configuration:
C
Installed Under Soffit After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exeed 24” deep. The top case trim overlaps the bottom of the soffit.
D
Wooden Wall Studs and
No Soffit
• Cut a 2” x 4” block and
secure to brackets provided.
• Secure brackets to back
wall of opening at 84” or your installation height from the floor.
E
Metal Wall Studs and
No Soffit This method requires securely fastened cabinets on both sides and a ¾” minimum wood brace above unit, with it’s front surface 24” from back wall.
• After installing unit into
opening, raise grille panel and attach metal case top trim to ¾” minimum wood brace.
• The brace spanning
the enclosure must be securely fastened to cabinets on both sides.
See Installation Instructions for detailed instructions.
Product Specification Revised 10/14
Page 8
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
*84
*84"
(213.4)
(213.4)
*Depending
*Depending
on installation
on installation
height
STANDARD INSTALLATION
NOTES
F
Side panels must be
used whenever the sides
of the refrigerator will
be exposed. The 1/4”
side panels will slip
into the side case trim.
Secure the panels to
the refrigerator with
stick-on hook and loop
fastener strips. Order
the side panels from the
cabinet manufacturer.
2 9/16"
(6.5)
Product Specification Revised 10/14
Page 9
1/4" Framed Panel
A
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
(24.4)
15 3/8"
(24.4)
15 3/8"
1/4" FRAMED PANEL DIMENSIONS
PANEL ASSEMBLY CROSS SECTION
Grille Panel
D E
Dispenser
Cutout
F
B
PANEL DIMENSIONS
G
Freezer
Panel
C
Fresh
Food
Panel
1/4" Framed Panel
Dispenser
Cutout
9 5/8"
Trim
A B C D E
39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"
Door
Supplied Handles
DISPENSER CUTOUT
(39.1)
POSITION
F G
17 13/16" 3 1/8"
STANDARD INSTALLATION
NOTES
Trimmed refrigerators are designed to be customized with decorative panels. Field­installed custom door and grille panels are required.
1/4” Framed Panels: Order trim kit #ZTK42SSH
for 1/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
3/4" OVERLAY PANEL DIMENSIONS
PANEL ASSEMBLY CROSS SECTION
1/4" Backer Panel
.10" Spacer Panel
Grille Panel
D E
Dispenser
Cutout
F
A
B
PANEL DIMENSIONS
G
C
Fresh
Freezer
Panel
Food
Panel
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
.25" + .10" + .75" = 1.10" Total Panel Thickness
Dispenser
Cutout
9 5/8"
Trim
39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"
39" 8 5/8" 67" 13 1/4" 23 1/4"
40 1/8" 9 3/4" 68 5/8" 14 13/16" 24 13/16"
Door
3/4" Overlay Panel
Supplied Handles
A B C D E
* DISPENSER CUTOUT
(39.1)
POSITION
F G
17 15/16" 3 1/4"
* Cut the dispenser opening after the backer, spacer
and overlay panels have been assembled.
3/4” Overlay Panels: Order trim kit #ZTK42SSH
for 3/4" thick custom panels ordered from your cabinet maker. The decorative panels slide into the trim.
The overlay panel must be secured to a 1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.
Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles:
The supplied handles can be adjusted to accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker, can also be installed. ZKHPSS1: Professional Tubular Stainless Steel Handle designed to fit 3/4" overlay panels. ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels.
Kits include one handle. Order 2 kits for side­by-side refrigerators from your Monogram suppplier.
Product Specification Revised 10/14
Page 10
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
DISPENSER TRIM
1/4" Framed Panel
Freezer Door
Ice/Water Dispenser
1/4"
Total
Thickness
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
Freezer Door
Ice/Water Dispenser
1/4" PANEL DISPENSER TRIM 3/4" OVERLAY PANEL DISPENSER TRIM
A B
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS
1/4" Backer Panel .10" Spacer
3/4" Overlay Panel
16 3/4"
1.10"
Total
Thickness
STANDARD INSTALLATION
NOTES
These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels.
1/4" Panel Dispenser Trim:
The framed panel must be 1/4” nominal thickness to fit the dispenser trim.
• The dispenser trim ts over the custom
panel and snaps into the freezer door.
• If the panel is less than 0.250" thick, a
noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.
• If the panel is more than 0.250" thick, the dispenser trim cannot be secured to the door.
3/4" Overlay Panel Dispenser Trim:
The 3/4” overlay dispenser trim is designed to fit a total panel thickness of
1.100".
10 5/8"
DISPENSER TRIM
1.10”
Total
C
Thickness
D
SIDE VIEW CROSS SECTION
(Showing Raised Overlay
with Middle Rail)
• If the panel is less than 1.100" thick, a
noticeable gap may be created around the dispenser trim.
• If the panel is more than 1.100" thick,
the dispenser trim cannot be secured to the door.
• The overlay panel must be constructed
according to the specifications shown to achieve the correct total thickness.
• Alternative panel construction methods
such as securing a 3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required
1.100" panel thickness.
• When a raised panel design is to be
used, a custom middle rail is required.
Raised Overlay Panel Design on Dispenser Models:
When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.
• The middle rail must be wide enough to
allow for the dispenser trim to overlap the opening.
• The middle rail must be 1.10” total
thickness to accept the dispenser trim.
Product Specification Revised 10/14
Page 11
FEATURES AND BENEFITS
Halogen Light Columns - Located in the freezer
and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination
LED Lighting - Located at the top of the fresh food compartment, and inside the vegetable and climate-control drawers, illuminates contents without compromising space
Advanced Temperature Management System with Multi-Shelf Air Tower - Provides even
distribution of air throughout the refrigerator
Climate-Control Drawer - Allows you to express­chill beverages, express-thaw meats and select specific temperatures for perishable foods
ZISB420DHGE Monogram® 42" Built-In Side-by-Side Refrigerator
Dispenser with Proximity Sensor - Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away
Dairy Bin with Center Divider - Has a unique magnetic seal that locks in freshness
Filter-Change Indicator Light - Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser
®
Water Filter - Has been moved from the
GE
fresh food compartment to the overhead cabinet, where it is discreetly out of sight
Drop-Down Shelf - Provides additional space for a casserole dish or pizza box
R
Product Specification Revised 10/14
Loading...