Page 1
SECTION 1
FLUSH INSET INSTALLATION
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
SECTION 2
STANDARD INSTALLATION
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
Product Specification Revised 10/14
Page 2
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
SPECIFICATIONS
Overall Width 38" (96.5 cm)
Overall Height 83 1/2" (212.1 cm)
Overall Depth 25 7/8" (65.7 cm)
Door Clearance 38 3/4" (98.4 cm)
Cutout Width 39" (99.1 cm)
Cutout Height 84 1/2" (214.6 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 570 lb (258.5 kg)
†
OVERALL DIMENSIONS
FLUSH INSET INSTALLATION
25 7/8" (65.7)
*3"
(7.6)
20 5/8" (52.4)
* 83 1/2"
(212.1)
SIDE VIEW
38" (96.5)
10 5/16"
(26.2)
69 13/16"
(177.3)
*73 1/4"
(186.1)
*3 3/8"
** Allow 17" (43.2) min
clearance for 115˚
door swing
(8.6)
*83 1/2"
(212.1)
†
†
FRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”
35" (89.0)
Case width
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
TOP VIEW
38 3/4"
(98.4)
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
Product Specification Revised 10/14
Page 3
FLUSH INSET INSTALLATION 3/4" PANELS
24" (61.0)
1 1/2"
(3.8)
3"
(7.6)
7/16"
(1.1)
Trim overlap
35 1/2" (90.2)
2 5/16"
(5.9)
SIDE VIEWFRONT VIEW
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
ELEC.
6"
(15.2)
10"
(25.4)
WATER
5"
(12.7)
5"
(12.7)
3 1/2"
(9.0)
WATER
10" (25.4)
FLUSH INSET INSTALLATION 3/4" PANELS
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
84 1/2"
(214.6)
Finished cleats
3 1/2"
(8.9)
W
ANTI-TIP BRACKET
81 1/2"
(207.0)
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
5 1/4" (13.3)
3/4" (1.9)
Width of side cleats
84 1/2"
(214.6)
Use two
additional hole
locations at end
of brackets
TOP VIEW
Case
Finished cleats
Case Trim
Door
3/4" Panel
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
ELEC.
9"
(22.9)
5 1/2"
(14.0)
26 3/16"
(66.5)
B
7"
(17.8)
WATER
3 1/2"
(9.0)
7"
(17.8)
FRONT VIEWSIDE VIEW
C
L
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
Ensure holes
selected are
centered on
the studs
Wall
Studs
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
1/2" (1.3)
(190.5 )
From floor
to bottom
of electrical
3 1/2"
(8.9)
A
75"
area
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
FLUSH INSET INSTALLATION
NOTES
NOTES
A
Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
See Installation
Instructions for detailed
instructions.
Product Specification Revised 10/14
Page 4
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION
A
Grille Panel
B
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
1/4" Router Cut Depth
for Hinge Clearance
Door
HINGE CLEARANCES
ROUTER 1/4" DEEP
Door
Panel
FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION
C
Z
Y
PANEL DIMENSIONS
A B C
38" 9 5/8" 69 13/16"
A
X
HINGE CLEARANCE
1 1/4" 1" 1/2"
PANEL DIMENSIONS
X Y Z
FLUSH INSET INSTALLATION
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels. Fieldinstalled custom door and grille panels
are required.
Adjustment brackets allow 1/8” ne
adjustment of panel position in 3
dimensions.
Use templates provided to locate mounting
brackets on the door and grille panels.
Maximum total panel weight:
• Fresh food door panels – 67 lbs.
• Grille panel – 11 lbs
Door Handles
Door handles not included. Custom handle
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4” panels. Kit includes
one handle – 30 1/2” long.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4” panels. Kit includes
one handle – 64 1/4” long.
Order #ZUGF2H: Unified grille kit for dual
installation. Maximum total panel weight -
25 lbs.
NOTE: For side-by-side installation of a leftand-right-hand door swing product only,
see
on following page.
B
D
Door
Panel
Grille Panel
D
Door
Panel
B
A B C D
74 1/2" 9 5/8" 69 13/16" 37"
HINGE CLEARANCE
X Y Z
1 1/4" 1" 1/2"
HINGE CLEARANCES
C
PANEL ASSEMBLY CROSS SECTION
PANEL ASSEMBLY CROSS SECTION
ROUTER 1/4" DEEP
Z
Y
1/4" Router Cut Depth
for Hinge Clearance
Door
X
Product Specification Revised 10/14
Page 5
75 1/2" (191.8)
Finished Width
26 3/16" (66.5)
Min. Cutout Depth
25 3/4" (65.4)
3 7/8"
(9.8)
5 1/2"
(13.9)
9"
(22.9)
84 1/2"
(214.6)
Finished
Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC.
5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
7"
(17.8)
7"
(17.8)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
5 3/4"
(14.6)
5 3/4"
(14.6)
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
DUAL INSTALLATIONS
3 7/8"
(9.8)
ELEC.
9"
(22.9)
84 1/2"
(214.6)
Finished
Opening
7"
(17.8)
WATER
3 1/2"
A
5 1/2"
(13.9)
(9.0)
FRONT VIEW
75 1/2" (191.8)
Finished Width
ELEC.
5 3/4"
5 3/4"
(14.6)
(14.6)
9"
(22.9)
WATER
3 1/2"
25 3/4" (65.4)
5 1/2"
(13.9)
(9.0)
7"
(17.8)
75 1/2"
From floor
to bottom
of electrical
3 1/2"
(8.9)
(191.8 )
area
26 3/16" (66.5)
Min. Cutout Depth
SIDE VIEW
FLUSH INSET INSTALLATION
NOTES
A
A separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
B
In a side-by-side installation of a left-and-
right-hand door swing product, 1 1/2”
clearance between the units is required.
Order ZUGF2H custom panel unified grille
kit for this installation.
C
In a side-by-side installation with same
door swing, allow 4” clearance between
the products to prevent the door swing
interference. Allow 15” minimum to a wall
to achieve full interior drawer extension
and pan removal. Additional clearances
are required when using custom panels
and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel
kits will not fit this installation.
3 1/2"
(8.9)
W
D
In a side-by-side installation with right
and left door hinges together, allow 5”
minimum clearance between the two
products to prevent one door from striking
the other. Additional clearances required
when using custom panels and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel
kits will not fit this installation.
DUAL PRODUCT CLEARANCES
25" (63.5) min
To wall
130˚
Door swing
1 1/2"
(3.8)
Door swing
B C
130˚
25" (63.5) min
To wall
5" (12.7) min
4" min
(10.2)
15" (38.1) min
To wall
D
Product Specification Revised 10/14
Page 6
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
36" (91.5)
25 1/8" (63.8)
23 7/8" (60.7)
*84"
(213.4)
*73 1/4"
(186.1)
69 5/8"
(176.8)
*3"
(7.6)
1 7/8"
(4.8)
*3 1/4"
(8.3)
*83 1/2"
(212.1)
35"
SIDE VIEWFRONT VIEW
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/8" (64.45 cm)
Door Clearance 36 3/4" (93.4 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 569 lb
OVERALL DIMENSIONS
36" (91.5)
69 5/8"
(176.8)
*3"
(7.6)
* Shipping height . Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
Case width
(89.0)
*73 1/4"
(186.1)
STANDARD INSTALLATION
25 1/8" (63.8)
23 7/8" (60.7)
1 7/8"
(4.8)
*84"
(213.4)
*83 1/2"
(212.1)
*3 1/4"
** Allow
25" (63.5) min
clearance for 130˚
door swing
(8.3)
SIDE VIEWFRONT VIEW
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An inidividual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
36 3/4"
TOP VIEW
(93.4)
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
**These units are equipped with a 2-position door stop. The factory set 130° door swing can
be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Allow 15" minimum
clearance to wall for pan removal. If the 90˚ door stop position is used, pan access is
maintained but pan removal is restricted.
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimension may vary due to manufacturing tolerances.
Product Specification Revised 10/14
Page 7
35 1/2" (90.2)
2 5/16"
(5.9)
24" (61.0 )
1 1/2"
(3.8)
3 1/8"
(7.9)
7/16"
(1.1)
Trim overlap
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
FRONT VIEW SIDE VIEW
3 1/2"
(8.9)
ELEC.
5 1/2"
(14.0)
9"
(22.9)
W
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
STANDARD INSTALLATION
2 5/16"
(5.9)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
ANTI-TIP BRACKET
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
ELEC.
9"
(22.9)
5"
(12.7)
35 1/2" (90.2)
A
WATER
3 1/2"
(9.0)
5 1/2"
(14.0)
B
81 1/2"
(207.0)
3 1/2"
5"
(12.7)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
(8.9)
locations at end
Use two
additional hole
of brackets
3 1/8"
(7.9)
24" (61.0 )
1 1/2"
(3.8)
W
C
L
Bracket
mounted
into vertical
wall studs
Ensure holes
selected are
centered on
the studs
Wall
Studs
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
7/16"
Trim overlap
3 1/2"
(8.9)
STANDARD INSTALLATION
(1.1)
NOTES
A
Mounting the junction
box in this location will
also allow for front
accessability through
access panel.
B
Water supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the antitip system you must use
the product installation
instructions.
The information below
applies to all installation
constructions:
• A wall bracket, bolts and
toggles will be supplied
with the unit.
• The bolts will be used to
attach bracket to wall in
4 locations. Two of the
locations must penetrate
the center of the wall
studs.
• The toggles are used for
stability in drywall and
when metal studs are
encountered. Lag bolts
are used in wood studs.
• In installation opening,
measure 81 ½” from
floor and draw a
horizontal line.
• Locate and mark the wall
studs on horizontal line.
Verify at least two studs
have their centerlines
within the center 32.5”
of installation opening to
ensure 2 wall studs are
penetrated.
• The bracket will be
centered left to right in
opening with bottom of
bracket on the horizontal
line.
• When unit is placed in
opening, the bracket tabs
will align with openings
in back of the unit. The
unit will be secured to the
bracket using supplied
“L” bolts.
See Installation
Instructions for detailed
instructions.
Product Specification Revised 10/14
Page 8
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
CUSTOM SIDE PANELS
F
24" (61.0)
3/16"
(.5)
1 7/8"
(4.8)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
*84”
*84"
(213.4)
(213.4)
*Depending
*Depending
on installation
on installation
height
STANDARD INSTALLATION
NOTES
F
Side panels must be
used whenever the sides
of the refrigerator will
be exposed. The 1/4”
side panels will slip
into the side case trim.
Secure the panels to
the refrigerator with
stick-on hook and loop
fastener strips. Order
the side panels from the
cabinet manufacturer.
2 9/16"
(6.5)
Product Specification Revised 10/14
Page 9
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
A
1/4" Framed Panel
1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION
PANEL ASSEMBLY CROSS SECTION
Grille Panel
Door
Panel
B
C
Trim
PANEL DIMENSIONS
A B C
1/4" Framed Panel
33 7/8" 8 7/8" 69 5/16"
Door
Supplied Handles
STANDARD INSTALLATION
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels. Fieldinstalled custom door and grille panels are
required.
1/4” Framed Panels:
Order trim kit #ZTK36SDHRH
for 1/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim.
Maximum total panel weight:
• Door panel – 67 lbs.
• Grille panel – 11 lbs
3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION
PANEL ASSEMBLY CROSS SECTION
Trim
1/4" Backer Panel
.10" Spacer Panel
PANEL DIMENSIONS
A B C
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
.25" + .10" + .75" = 1.10" Total Panel Thickness
33 7/8" 8 7/8" 69 5/16"
32 1/2" 7 5/8" 67 15/16"
34 1/8" 9" 69 9/16"
Grille Panel
Panel
A
Door
B
C
Door
3/4" Overlay Panel
Supplied Handles
3/4” Overlay Panels:
Order trim kit #ZTK36SDHRH
for 3/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim. The overlay panel must be
secured to a 1/4"-thick backer panel which
slides into the trim. A spacer panel 0.10" thick
must be placed between the overlay and
backer panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Door panel – 67 lbs.
• Grille panel – 11 lbs
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional Tubular Stainless Steel
Handle designed to fit 3/4" overlay panels.
Kits include one handle - 30 1/2" long.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" overlay panels.
Kits include one handle - 64 1/4" long.
Product Specification Revised 10/14
Page 10
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
1/4" Framed Panel
Supplied Handles
STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION
D
Door
Panel
PANEL ASSEMBLY
CROSS SECTION
A
Grille Panel
Trim
D
Door
Panel
B
C
Door
PANEL DIMENSIONS
A
B
C
D
1/4"
Framed
Panel
69 7/8"
8 7/8"
69 5/16"
33 7/8"
STANDARD INSTALLATION
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels. Fieldinstalled custom door and grille panels are
required.
1/4” Framed Panels:
Order trim kit #ZTK36SDHRH
for 1/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim.
Maximum total panel weight:
• Door panel – 67 lbs.
• Grille panel – 25 lbs
Order ZUG2: Unified grille kit for dual
installation. Maximum total panel weight -
25 lbs.
STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION
PANEL DIMENSIONS
1/4"
Backer
Panel
69 7/8" 68 1/2" 70 1/8"
A
8 7/8" 7 5/8" 9"
B
69 5/16" 67 15/16" 69 9/16"
C
33 7/8" 32 1/2" 34 1/8"
D
.25" + .10" + .75" =
1.10" Total Panel Thickness
D
Door
Panel
PANEL ASSEMBLY
CROSS SECTION
A
Grille Panel
1/4" Backer Panel
.10" Spacer Panel
Panel
Trim
D
Door
B
C
Door
3/4" Overlay Panel
Supplied Handles
.10"
Spacer
Panel
3/4"
Overlay
Panel
3/4” Overlay Panels:
Order trim kit #ZTK36SDHRH
for 3/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into the trim. The overlay panel must be
secured to a 1/4"-thick backer panel which
slides into the trim. A spacer panel 0.10" thick
must be placed between the overlay and
backer panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws must
be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Door panel – 67 lbs.
• Grille panel – 25 lbs
Order ZUG2: Unified grille kit for dual
installation. Maximum total panel weight -
25 lbs.
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional Tubular Stainless Steel
Handle designed to fit 3/4" overlay panels.
Kits include one handle - 30 1/2" long.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" overlay panels.
Kits include one handle - 64 1/4" long.
Product Specification Revised 10/14
Page 11
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
71 1/2" (181.6)
Finished Width
24" (61.0)
Min. Cutout Depth
24 3/16" (61.4)
2 5/16"
(5.9)
5 1/2"
(13.9)
9"
(22.9)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
3 1/2"
(8.9)
W
FRONT VIEW
ELEC.
5 1/2"
(13.9)
9"
(22.9)
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
SIDE VIEW
5"
(12.7)
5"
(12.7)
5"
(12.7)
5"
(12.7)
WATER
3 1/2"
(9.0)
WATER
3 1/2"
(9.0)
DUAL INSTALLATIONS
2 5/16"
(5.9)
9"
5 1/2"
(13.9)
WATER
3 1/2"
(9.0)
1"
(2.5)
ELEC.
(22.9)
83 1/2" min
84 1/2" max
(212.1-214.6)
Finished Opening
5"
(12.7)
DUAL PRODUCT CLEARANCES
25" (63.5) min
To wall
A
71 1/2" (181.6)
Finished Width
ELEC.
(22.9)
5"
(12.7)5"(12.7)
FRONT VIEW
24 3/16" (61.4)
9"
WATER
3 1/2"
(9.0)
25" (63.5) min
To wall
5 1/2"
(13.9)
5"
(12.7)
of electrical
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
area
Min. Cutout Depth
SIDE VIEW
2" min
(5.1)
24" (61.0)
STANDARD INSTALLATION
NOTES
A
A separate 115V, 60Hz, 15- or 20-amp
power supply is recommended for each
product.
Additional cutout width may be required when
side panels are used.
B
In a side-by-side installation of a left-
and-right-hand door swing product, 1”
clearance between the units is required.
Order ZUG2: Custom panel unified grille kit for
one continuous grille panel.
C
In a side-by-side installation with same
door swing, allow 2” minimum clearance
between the products to prevent the door
swing interference. Allow 15” minimum
to a wall to achieve full drawer extension
and pan removal. Additional clearances
are required when using custom panels
3 1/2"
(8.9)
W
15"
(38.1) min
To wall
and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel
kits will not fit this installation.
D
In a side-by-side installation with right
and left door hinges together, allow 5”
minimum clearance between the two
products to prevent one door from striking
the other. Additional clearances required
when using custom panels and handles.
NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel
kits will not fit this installation.
130˚
Door swing
B C
130˚
Door swing
5" (12.7) min
D
Product Specification Revised 10/14
Page 12
FEATURES AND BENEFITS
Custom Appearance - Allows personalization
with cabinet-compatible panels an custom
handles
Upfront Electronic Controls with Digital Readout
- Allows precise temperature settings and are
positioned for maximum ease of use
Humidity Controlled Vegetable Compartments
and Sealed Snack Pans - Help maintain freshness
and help preserve foods longer
Adjustable, Spill Proof Glass Shelves - Make it
easy to customize storage to handle foods and
containers of various sizes
2 Sealed Deli Pans with Full-Extension Slides
ZIR360NHRHGE Monogram® 36" Built-In All-Refrigerator
Six Adjustable Door Bins - Offer added storage
flexibility
™
GE Water
Filtration System - Delivers clean,
great tasting ice
R
Product Specification Revised 10/14
Loading...