GE ZIC360N RH, ZICS360N RH, Monogram ZIC360NRH, Monogram ZICS360NRH, Monogram ZICS360NLH Design & Installation Manual
Installation
Instructions
ZIC360NRH,ZIC360NLH,
ZICS360NRH,ZICS360NLH
Built-In Bottom-Freezer
Refrigerators
Design Guide
With Installation Instructions
Q
Monogram;'
We bring good things to life
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT Save these instructions for
local inspector's use. Observe all governing
codes and ordinances.
• Note to Installer- Be sure to leave these instruc-
tions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner's Manual for future reference.
WARNING:
This appliance must be properly grounded. See
"Grounding the Refrigerator," page 9.
AVERTISSEMENT
Cet appareil dolt 6tre correctement mis _ la terre.
Consulter <<Mise a la terre du rOfrigerateur _, page 9.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product- TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
PRUDENCE
tk cause du poids et de la taille de ce refrigerateur et
pour reduire le risque de blessure et de dommages, IL
FAUT DEUX PERSONNES POUR FAIRE
L'INSTALLATION CORRECTEMENT.
Skill Level - Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the in-
staller. Product failure due to improper installation is
not covered under the GE Appliance Warranty. See
the Owner's Manual for warranty information.
WARNING:
• These refrigerators are top-heavy and must be
secured to prevent the possibility of tipping for-
ward. Anti-Tip protection is required. See page 11
for details.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
AVERTISSEMENT
• Ces refrigerateurs sent lourds en haut et il faut les
arrimer pour eviter leur basculement. II faut avoir
un syst_me de protection centre le renversement.
Voir les details page 11.
• Ii ne faut utiliser cet appareil que pour l'utilisation
appropriee.
• Reparer ou remplacer immediatement tout cordon
electrique effiloche ou endommage.
• Ii faut debrancher le refrigerateur avant le
nettoyage ou toute intervention.
• tes reparations doivent Otre faites par un
technicien qualifie.
For Monogram local service ill your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call
1-800-626-2002.
www. monogram.com
CONTENTS
PlanningGuide
TheInstallationSpace....................................3
DimensionsandClearances..........................3
130° DoorSwing..............................................4
90° DoorSwing................................................5
CustomizationBasics.....................................6
PanelDimensions............................................7
Side Panels .......................................................8
ZUG2GrillePanel Dimensions......................8
Installation Instructions
Tools,Hardware, Materials ...........................9
Grounding the Refrigerator............................9
Step 1, RemovePackaging ..........................10
Step 2, Install Water Line .............................10
Step 2A, ROWater Line ................................11
Step 3, Install Side Panels ...........................11
Step 4, Install Anti-lip Brackets .................11
Step 5, Level Refrigerator ............................12
Step 6, Secure Refrigerator to Cabinetry ..12
Step 7, Adjust DoorSwing ...........................13
Step 8, Install Grille Panel ............................13
Step 9, Install FramedPanels......................14
Step 9A, Install Overlay Panels ...................15
Step I0, Connect Water Supply ..................16
Step 11,Connect Power ...............................16
Step 12,Start Icemaker ................................16
Step 13,Install Toekick.................................16
2
Design Guide
THE INSTALLATION SPACE
The finished
cutout width
must be
35d/2".
84-1/2"max
83-1/2"min
Finished
T
35-1/2"
_FinishedWidth_
10" _'_ Electrical
Area
¢
24"CutoutDepth
11/2" 31/2_
WallView
74-1/2"From
Floorto Bottom
of Electrical
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
Designed for industry standard flush installation. The
refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
, A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
• Water line can enter the opening through the floor
or back wall. The water line should be 1/4" O.D.
copper tubing between the cold water line and
water connection location, long enough to extend
to the front of the refrigerator. Installation of an
easily accessible shut off valve in the water line is
recommended.
38"
CaseWidth
DIMENSIONS AND
CLEARANCES
* Shippingheight,The
*84" From refrigeratorcanbeadjusted
Floorto to fit into a cutoutthat is
TopFrame 83-1/2"min,to 84-1/2"max,
height.Notethat the topcase
trim atthefront is 1/2"higher
andwill overlapupper
cabinetryorsoffit. Use
levelinglegsandwheelsfor
heightadjustment.
Frameto Frame
Width
Product Clearances
These refrigerators are equipped with a 2 position
door stop. The factory set 130 ° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets or
walls is restricted.
130° Door Swing
25"_
Minimum
, to Wall
I \\
,k k,
X X, k,
X
X,
X,
\,\\,\\
130°....... ..Y
90° Door Swing
Behind
il 'Fr3iame
i ii
-3/4"
'S
90°.........
Allow 25" minimum clearance for a full 4" Minimum
130 ° door swing. Allow 15" for pan removal, to Wall
4" minimum clearance is required when door swing
is adjusted to 90 °. If the 90 ° door stop position is
used, pan access is maintained, but pan removal is
restricted.
See illustrations pages 4 and 5 to determine door
swing interaction with adjacent cabinets or
countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
, If you are installing two refrigerators, side by side,
the installation space must be "/1-1/2" wide.
Note: Additional cutout width maybe required when side panels
are used. Add side panel thickness to the finished cutout to
calculate rough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate l15V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
q_ 71d/2"FinishedWidth
84q/2"max
83q/2"min
Finished
2-5/16" i
_Electrical _ _ 24-3/16"
IF7" : IFT'
18" 10"
L24"Cutout
Depth
Opening 5) WaterSupply
i
_ 26"_ _ 26"_
3-1/2"
WallView
74-112"From
F[{)orto Bottom
of[[ectrical
M/2"
3
Design Guide
Refrigerator
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
23-7/8"From
Rearof
Refrigerator
FramelessCabinets:The case trim
overlaps cabinets atthe to ) andsides.
Therefore, frameless cabinets may
require filler strips to prevent inter-
ference with cabinet door swing. The
opening mustallow for filler strips.
Case
Trim
3/4"
1/2"
1/4"
2 _
1-3/4"
i
1-1/2" :
1-1/4"
2-3/4"
2-1/2"
2-1/4"
3_
", 3/4"Overlay
', Panel
/ominal Size
Door
Top View
130 ° DOOR SWING
(factory setting)
Scale 1:1
Design Guide
Refrigerator
\
\
\
\
\
\
\
\
\
\
\
\
\
\
Top View
90 ° DOOR SWING
(optional setting)
Scale 1:1
\
\
\
\
\
\
\
\
\
\
Door
_Case _im
FramelessCabinets:The
case trim overlaps cabinets
at the top and sides.
Therefore, frameless
cabinets may require filler
strips to prevent inter-
ference with cabinet door
swing. The opening must
allow for filler strips.
23-7/8"
FromRearof
Refri_erator
r
I
i i i
.... 1/2
3/4'_
I I
1-1/4"
1-1/2"
3/4" Overlay
Panel
(NominalSize)
1-1/4"
Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Models Available
Stainless Steel Wrapped Models:
ZICS360N RH (right-handed door)
ZICS360N LH (left-handed door)
Trimmed models:
ZIC360N RH (right-handed door)
ZIC360N LH (left-handed door)
Overlay panels
You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides a
seamless appearance which integrates smoothly with
surrounding cabinetry.
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door and
grille panels are required.
DoorHandle 1/4" ThickBackerPanel
Standard supplied handles shown in 3/4"overlay panel position.
Framed panels
You may install 1/4" thick custom panels from your
cabinet manufacturer. The decorative panel slides into
the factory installed trim. Or, order black, white and
stainless steel accessory panels from your Monogram
dealer.
Door and Drawer Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed. If desired, you may order ZKHCSS2
Monogram stainless steel tubular handle kit for overlay
panels.
Side Panels
Side panels must be used whenever the sides of the
refrigerator will be exposed.
StandardDoorHandle FramedPanel
Standardsupplied handles shown in 114"panel position.
Optional Accessory Kits
, ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit overlay panels.
• ZUG2: For side by side installation of two trimmed
bottom-freezer refrigerators. This kit provides for the
installation of a unified custom grille panel to span the
width of two units using a framed or overlay panel.
• ZUGSS2: For side by side installation of two stainless
steel wrapped bottom-freezer refrigerators. This kit
provides a unified stainless steel grille panel to span
the width of two units.
Accessory Panels
White, black and stainless steel accessory panels are
available from your Monogram dealm: Panels are cut to
size and ready to install.
ZPBC360-Black, ZPWC360-White,
ZPSC360-Stainless Steel Panels
6
Loading...