Page 1
Installation
Instructions
Professional Style
Bottom-Freezer Refrigerators
ZICP720
Design Guide
With InstGIlation Instructions
49-60469
224DI234PO01
07-06 JR
@
Monogram:
Page 2
Safety Information
BEFOREYOUBEGIN
Readthese instructions completely and carefully.
•INPORTANT-Savetheseinstructionsfor
local inspector's use.Observeall governing codes and
ordinances
• Note to Installer- Besureto leavetheseinstructions
with the Consumer
• Note to Consumer- Keeptheseinstructionswith uour
Owner's Manual for future reference.
WARNING:
Thisappliance must be properlUgrounded.See"Grounding
the Refrigerator,"page6.
AVERTISSEMENT'.
Cetappareil doit _tre correctement mis 0 la terre.
Consultez<<Mise0 laterre du rdrig@rateur >>,page 6.
If Uou receiveda damaged refrigerator,Uoushould
immediately contact your dealeror builder.
CAUTION:
Dueto the weight and sizeof this refrigerator,and to reduce
the riskof personalinjurUor damage to the product-THREE
PEOPLEAREREQUIREDFORPROPERINSTALLATION.
PRUDENCE'.
Acausedu poidsetdelatailledece rdrig_ratoretpourr_duire
lerisquedeblessureetdedommages,ILFAUTTROISPERSONNES
POURFAIREUINSTALLATIONCORRECTEMENT
SkillLevel- Installation of this refrigerator requires
basic mechanical, carpentru and plumbing skills,Proper
installation isthe responsibilitUof the installer.Product
failure dueto improper installation is not coveredunder
the GEApplianceWarrant U.Seethe Owner's Manual for
warrant Uinformation.
WARNING:
• Theserefrigerators are top-hea% and must besecured
to preventthe possibilitUof tipping forward. Anti-Tip
protection is required.Seepages 9 and !0 for details.
• Usethis appliance only for its intended purpose.
ImmediatelUrepair or replace electricservice cords that
become fraued or damaged.
Unplugthe refrigerator before cleaning or making repairs.
Repairsshould bemade bUa qualified servicetechnician.
AVERTISSEMENT'.
• Cesrdrig@rateurssont Iourdsen haut et ilfaut les
arrimer pour @viterleur basculement. IIfaut avoir un
sgst@mede protection contre lerenversement.Voir
lesd_tails pages 9 et !0.
• IIne faut utiliser cetappareil que pour I'utilisation
appropri@e.
• R@parezou remplacezimm@diatementtout cordon
@lectriqueeffiloch@ou endommag@.
• IIfaut d@brancherlerdrig@rateuravant le nettoyage
ou toute intervention.
• Lesr@parationsdoivent@trefaites parun technicien qualifi&
For Monogram local service in gout area,
call 1.800.444.1845.
For Monogram service in Canada, call 1.888.880.3030.
For Monogram Partsand Accessories,call 1.800.626.2002.
www. monogram.cam
CONTENTS
Planning Guide
The Installation Space ......................3
Dimensions and Clearances ..........3
!30 ° Door Swing ..................................4
90 ° Door Swing ....................................5
Installation Instructions
Tools, Hardware, Trim,
Materials, Flooring ..............................6
Grounding the Refrigerator ............6
Step !, Remove Packaging ............7
Step 2, Install Water Lines ..............7
Step 3, Install New Side Trim ..........8
Step/4, Install Side Panels ................8
Step 5, Install Anti-Tip Brackets....9
Step 6, Install New Top Trim ........!0
Step 7, Level Refrigerator ..............!0
Step 8, Alternate Anti-Tip
Procedure ..............................!!
Step 9, Secure Refrigerator
to Cabinetrg ........................ii
2
Step !0, Install Center
Trim Strip ............................12
Step !!, Install Grille BaseCover....!2
Step 12, Remove Both Grille
Panels (if present) ..........13
Step 13, Install Grille Panel
Onto Hinges ......................13
Step 14, Adjust Door Swing ..........14
Step 15, Connect Water Supplg _14
Step 16, Connect Power ................15
Step 17, Start Icemaker ................15
Step 18, Install Toekick ..................15
Page 3
Design Guide
THE INSTALLATION SPACE
The installation space must be 71-1/2",
f 71-1/2"FinishedWidth ........................................f
ll 2-5'16" ',
"1 Wall
/k 5/'j E!ectricalf 24-3/ 6"-I View
--/ _ 6 , mm_ 6" |
!, 1 t
max I 10 i ]u .
83-I/2"tl ' 75 From
rain J_ 24"Cutout i Finished
FinishedI Depth , Floorto
• I ,, Bottomof
upenmg| _" W " 5" Electrical
I / " t aterSupply ,, WaterSupply T Area
" i I _ j
/ I, i
Z ............26 ...................\ /: ............26" .................\
3-1/2" 3-1/2"
Water And Electrical Locations
Electrical and water supply must be located
as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly
beyond adjacent cabinetry, depending on your
installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top
case trim overlaps the bottom of the soffit.
DIMENSIONS AND CLEARANCES
71-1/2" 25-3/4"
CaseWidth CaseDepth
Shippingheight.The
refrigeratorscanbe
adjustedtofit intoa
cutoutthatis 83-1/2"
min.to84-1/2"max.
83-1/2"
atRear
72"Frame
toFrame '
28-11/16"
DepthIncluding
Handles
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set 130 ° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets
or walls is restricted.
25"_
Min.toi 130° Door
Wall
I
/L
Width
0 ,!
Swing Swing
H 130° Door
11
q-' '-F
i L
Notethatthetopcase
trimatthefrontis 1/2"
higherandwilloverlap
uppercabinetryor
soffit.Uselevelinglegs
andwheelsfora
maximum1"height
adjustment.
__25"__I
Min.to
Wall
/,,
,, "":::",,:::,,::::!
Additional Specifications
cA separate 115 volt 60Hz., 15 or 20 amp power
supply is recommended for each product, An
individual properly grounded branch circuit or
circuit breaker is recommended. Install properly
grounded 3-prong electrical receptacles recessed
into the back wall, Electrical must be located on
rear wall as shown,
NOTE: GFI (ground fault interrupter)is not
recommended.
Both water lines can enter the opening through
the floor or back wall. Route GE SmartConnect"
kit or 1/4" O.D. copper tubing between the cold
water line and the water connection location.
The tubing should be long enough to extend to
the front of the refrigerator. Installation of an
easily accessible shut-off valve in the water
line is required.
Allow 25" minimum clearance for a full 130° door
swing. Allow 15" for pan removal.
5" minimum clearance is required when door swing
is adjusted to 90°, Ifthe 90° door stop position is
used, pan access is maintained, but pan removal
is restricted.
See illustrations on pages
4 and 5 to determine door
swing interaction with
adjacent cabinets or
countertops,
90° Door 123-7/8"
Swing / Behind
, !, _Frame
L! i
T
!i 36-3/4-
90o.........
5" Minimumto
Wall
Page 4
Refrigerator
Design Guide
23-7/8"From
Rearof
Refrigerator
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets mag require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
Case
Trim
_J 1/2"
1/4"
3/4"
1-3/4" 2-3/4"
1-1/2" 2-1/2"
1-1/4"
.
2-1/4"
3/4" Overlay
Panel
",, (NominalSize)
Top View
130° DOOR SWING
(factorg setting)
Scale 1:1
Door
1-1/4"
Page 5
Design Guide
- Frameless Cabinets- The
case trim overlaps cabinets
at the top and sides.
Refrigerator Therefore, frameless
J_ CaseTrim cabinets mag require
J .......... filler strips to prevent
I interference with cabinet
I door swing. The opening
t must allow for filler strips.
\ -- ] FromRearof
_°23-7/8"
i.... ',--- ',.... ,,-- 1/4
iq:i.....u
_"_._ L
I I ! ............. 1-1/2"
E_
I I ;;;;;;;;! ',
Jl ',
I I
II
I I !
I I
I I ::::} ',
I I
I I
II
Jl Door
I I I
I I I
II
I I
II '
II .......
LI i
Ill , 3/4Overlay
I] Pane
I I
Top V0ew II
90 DOOR SWING II , .........
(opbonal setting) II , u
scale 1:1 , 1-1/4"
• , ,
@ i i
II I ', '
•
II I i "
II
j i i i
i ! i
, , NominalSize
i
i i
............. 1-1/4
I
, .
5
Page 6
Installation Instructions
TOOLS REQUIRED
• Tinsnips to cut banding
• Stepladder
• Bucket
• Level
• Appliance dollg
• Tubing cutter
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16",7/16" socket
Safetgglasses
1-1/4" and 1/2" open-ended wrench
• Pliers
,, !/4" ratchet or 1/4" angled wrench
HARDWARE SUPPLIED
• Water filter bgpass plug
• Anti-Tip brackets
,, 1/4"nut and ferrule
TRIM SUPPLIED
A. Soffit vent top
13. Left inside case trim
C. Right inside case trim
D. Center U-shape trim
E. Grille base wrap
F. Grille panel
G. Toekick
H. Foam spacer pads
I. Phillips screws
MATERIALS REQUIRED
,, 71" long 2x4 for Anti-Tip support
• 1/4" copper water line tubing or two GE
SmartConnect T"Refrigerator Tubing kits
• Two water shut-off valves
• Screws to secure refrigerator to cabinetrg
• Stick-on hook and loop fastener strips for 1/4"
side panels
FLOORING
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should be
strong enough to support a fullg loaded refrigerator, or
approximatelg 2,400 Ibs.
NOTE:Protect the finish of the flooring. Cut a large section
of the cardboard carton and place under the refrigerator
where gou are working.
A
B
C
D
FE
G
I
GROUNDING THE REFRIGERATOR
IMPORTANT--(Please read carefully)
FOR PERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLYGROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibilitg of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked bg a
qualified electrician to make sure the outlet is
properlg grounded.
Where a standard 2-prong wall outlet is encountered,
it is gour personal responsibilitg and obligation to
have it replaced with a properlg grounded 3-prong
wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWERCORD.
DO NOT USE AN ADAPTER PLUGTO CONNECT THE
REFRIGERATORTO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE,
Page 7
Installation Instructions
I_1 REMOVEPACKAGING
CAUTION:Refrigeratorismuch heavierat the top than at
the bottom-be careful when moving.When using a hand truck,
handle from sideonly.
PRUDENCE:Lerdrig@ateurestbeaucoupplusIourd
enhautqu'enbas.IIfaut@treprudentIorsdesd@lacements.
Siundiableestutilis@,ilfaut souleverlerdrig@rateursurlec6t@
seulement.
• Carefully cut banding at the top and bottom, remove outer
carton.
• Slideout backcorner posts(2).
• Slidecarton off top of cabinet.
NOTE:ITISNOTNECESSARYTOLAYCABINETDOWNINORDER
TOREMOVESKID!
• The unitis securedto the skidwith 4 slotted tie-down straps.
Removethe four 5/!6" boltsfrom the basechannels inthe
tie-downs.
• Removethe four 7/16"
bolts securingthe straps
to the skid
CAUTION:DONOT
ATTEHPTTOROLLUNIT
Remove
Fie-Downs
./
• Support blockson the bottom of the refrigeration case must
be removed beforethe refrigerator istaken offthe skidor
damage will occur,Carefully tilt refrigerator and slide blocks
out from beneath.
• Liftthe refrigerator off the skidwith an appliance dolly.
Handlefrom the sides.
OFFSKID.
PRUDENCE:
ILNEFAUTPASESSAYER
DEFAIREROULERLE
REFRIGERATEURPOUR
L'ENLEVERDELAYPALETTE.
_1 INSTALL WATER LINES
• A cold water supply isrequired for automatic icemaker
operation.Thewaterpressuremustbebetween40and120
p.s.i.
• Route1/4" ODcopper orGESmartConnecf" plastic tubing
between housecold water line and the water connection
location.
• Tubing shouldbe long enough to extend to the front of the
refrigerator.Allow enough tubing to accommodate bend
leading into the water lineconnection.
NOTE:The only GEapproved plastictubing issuppliedin
the GESmartConnecf" Refrigerator Tubing kits.Do not use
any other plasticwater supply line because the lineisunder
pressureat alltimes. Othertypes of plasticmay crack or
rupture with age and cause water damage to your home.
GESmartConnecf" RefrigeratorTubing Kitsare available inthe
following lengths:
2'(,6m) WXO8XIO002
6'(1,8 m) WXO8XIO006
15' (4%m) WXO8X10015
25' (7.6m) WXO8X10025
Shut off the main water supply.
Turnon the nearestfaucet long enough to clearthe lineof
water.
• Install a shut-off valve betweenthe icemakerwater valve and
cold water pipe ina basement or cabinet. Theshut-off valve
should belocated where it will be easily accessible.
_jiji1[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iii[iiiii11[iiiii{_i
\ Waterline J'
Tubing
•Turn on the main water supply and flushdebris.
Runabout a quart of water through the tubing into
a bucket. Shutoff water supply at the shut-off valve.
NOTE:Saddletype shut-off valvesare included in many water
supply kits.Before purchasing, make surea saddletype valve
complies with your local plumbing codes.
248CNRshall be adheredto. Saddlevalvesare illegal anduse
is not permitted in Massachusetts.Consultwith your licensed
NOTE:Commonwealth of MassachusettsPlumbingCodes
lumber.
Ifthe water supply to the refrigerator isfrom a Reverse
OsmosisWater System, usethe refrigerator's filter bypassplug.
Usingthe refrigerator's water filtration cartridge with the RO
filter can result inhollow ice cubes.
erBypass:
Page 8
Installation Instructions
J3] INSTALL NEW SIDE TRIM
CAUTION: Handle parts with care to avoid
scratching.
• Remove the inside case trim on both refrigerators.
FoamSpacer
Pads
/
/
/
/
Applg the supplied foam spacer pads to the mating
side of one product as shown.
Remove the Phillips head screws from the inside
case trim of each product as shown. Remove and
discard side trim. Retain screws.
J_ INSTALL SIDE PANELS
Side panels must be used whenever the sides
of the refrigerator will be exposed. The i/4"
side panels will slip into the side case trim.
Secure the panels to the refrigerator with
stick-on hook and loop fastener strips. Order
the side panels from the cabinet manufacturer.
Cut a notch in the top front corner as shown
to allow clearance for corner kegs in the front
side trim.
Skip this step if gou are not using side panels.
Install new side case trim with notches toward the
bottom. Install with original screws.
* Dependingon
installationheight
Page 9
Installation Instructions
151 INSTALL ANTI-TIP BRACKETS
WARNING: A.TI-TIPPRECAUTIO.S
The refrigerator is top-heavg and must be secured
to prevent the possibilitg of tipping forward.
ATTENTION : PRECAUTIONSCONTRELES
BASCULEMENTS
Le r6frig6rateur est beaucoup plus Iourd en
haut et il faut le maintenir en place pour 6viter
la possibilit6 de son basculement vers I'avant.
• Cut a 2" x 4" x 71" block and secure the block
to the mounting brackets provided using #12
or #1/4 wood screws.
2x4Cut _,
71"Length
InstallationHeight Mounting
FromFloor Bracket
_] INSTALL ANTI-TIP BRACKETS (cont.)
• Screws must penetrate at least one inch into
vertical wall studs.
• Before pushing the refrigerator into the opening,
plug the power cord into the receptacle. Open the
grille panel and reach into the opening at the
back to grasp the power cord. Pull the power cord
into the opening as gou push the refrigerator back.
• Gentlg push refrigerator into the opening with
hands against front corners.
IMPORTANT NOTE: When the refrigerator is
installed under a soffit or if there is not enough
height for this method of securitg, brackets cannot
be used. Proceed to step 6 to level the refrigerator
and then to step 8 to secure refrigerator to
cabinets. The refrigerator must be secured
to prevent tipping.
Screws Mountedinto j
VerticalWallStuds
• Secure the bracket with wood block to the back
wall so that it is 84" (or gour installation height)
from the finished floor. Use #12 or #1/4 wood
screws. See illustration.
Brackets
Required
B
SideView
Sti!f Brackets
-- Not Required
-- Beneatha
Soffit
Page 10
Installation Instructions
[_ INSTALLNEW TOPTRIM
• Remove 2 trim screws from the back
side of each corner. Lift off and discard
top case trims. Retain screws and
corner "L" brackets.
• Install the unified top trim by inserting
an "L" bracket into each corner.
• Install 2 screws in each "L" bracket
to secure the corners.
"L"Bracket
[_ LEVEL REFRIGERATOR
Both refrigerators MUST BE LEVEL AND PLUMB
with each other and with adjacent cabinetrg on
each side. Toekick heights should align with cabinetrg.
Both refrigerators have 4-point leveling. The front is
supported bg leveling legs, the rear is supported
bg adjustable wheels. Both are accessible from the
front of the refrigerator.
• To level the back of the refrigerator, turn the 7/26" hex
nut located above the front wheels. Turn clockwise to
raise or counterclockwise to lower the refrigerator.
• For front leveling, use a 2-2/4" open-end wrench.
• Adjust height of refrigerator to match installation
cutout opening 83-!/2 to 84-2/2". The refrigerator
should be level and plumb with cabinetrg.
• The inside case trims must align, top to bottom.
HexNutAdjusts _ll L
RearWheels _ [
LevelingLe
CAUTION:
The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If
the installation requires more than 84-1/2" height,
the installer should elevate the refrigerator on a
sheet of plgwood or runners. Cabinetry trim could
also be added across the top of the opening to
shorten the opening. If you attempt to raise the
refrigerator more than 1", gou will damage the
front leveling legs and the rear leveling wheels.
PRUDENCE:
Les roues de nivellement arri@e etles pattes de
nivellement avant permettent un r_glage maximal
de 25 mm (1 po). Si I'ouverture pour le r_frig@ateur
a une hauteur sup@ieure _ 2,15 m (84-1/2 po),
I'installateur dolt _lever le r_frig@ateur sur une
feuille de contre-plaqu_ ou des glissi@es. II est
_galement possible d'ajouter des baguettes de
finition des placards sur le haut de I'ouverture afin
de la r_duire. Lever le r_frig_rateur de plus de
25 mm (1 po) endommage les pattes de
nivellement avant et les roues de nivellement
arri_re.
10
Page 11
Installation Instructions
_1 ALTERNATE ANTI-TIP PROCEDURE
The refrigerator must be secured to prevent tipping.
The anti-tip brackets cannot be used on metal
wall studs. Use this Alternate Procedure to secure
the refrigerator against tip-over whenever metal wall
studs are encountered and there is no soffit.
• Raise the grille panel to access case trim.
• Usea 3/16" bit to drill four evenly spaced clearance
holes through the metal top case trim.
• Use a 1/16" bit to drill pilot holes through the metal
clearance holes and into the wood soffit. The holes
should be centered in the soffit or a 3/4" min. wood
brace. The brace spanning the enclosure must be
securely fastened to cabinets on both sides.
• Install four 1-1/2" drywall screws into the pilot holes.
SideView
TopCaseTrim
TopCaseTrim
InstallFour1-1/2"DrywallScrews
ThroughTrimandIntoSoffitor
3/4"Min.WoodBrace
19] SECUREREFRIGERATORTO CABINETRY
Whenever possible, perform this step for anti-tip II
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Raise the grille panel to access case trim.
• Drill hole in trim and drive screw through the trim -_
into adjacent cabinet.
• Follow the same procedure on the opposite side.
,I
DriveScrewsThrough
CaseTrimandInto
AdjacentCabinets
11
Page 12
Installation Instructions
E_ INSTALLCENTERTRIMSTRIP
• Open doors fully.
• Starting at the top, press center trim strip over the
inside case trims of both refrigerators.
• Continue pressing trim until you reach the bottom of
the case trims. The trim should align with the top and
bottom of case trims.
[] INSTALLGRILLEBASECOVER
CaseTrim
U-Shape
Trim
• Open doors fully.
• Grasp grille panel at the center and lift up to stop position.
• Remove one screw on each end of the grille base wrap.
Remove the wrap.
• Install the unified double width grille base wrap by
slipping the notched ends over the hinges.
• Install one screw on each end and 2 at the center.
UnifiedBaseWrap
_ Remove _0
Screws
PlaceTrim
OverHinges
12
Page 13
Installation Instructions
[_] REMOVEBOTHGRILLEPANELS(if present)
• Remove 3 screws holding the grille panel to the
hinge on each side. Lift grille panel off the hinges.
Discard both grille panels. Retain screws.
Leave hinges in open position.
Do not push hinges back.
[_ INSTALLGRILLEPANELONTO HINGES
• Place the new unified grille panel over the hinges,
matching screw hole locations.
• Install 3 screws through each hinge and
into the bracket.
GrillePanel
Remove3 Screws
GrillePanel
• Grasp panel at the center and pull down to close.
NOTE: Check alignment of grille panel to the top of
the doors. To adjust, loosen bracket hinge screws
on all/4 hinges. Adjust and tighten screws.
Install3Screws
13
Page 14
Installation Instructions
[_ ADJUSTDOORSWING
NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fullg to 130°, gou mag change the door swing to
a 90° opening. Skip this step if door opening is
satisfactory for your installation situation,
• Lift the grille panel to access the wire cover trim.
• Remove screws on both sides of the wire cover
trim and lift off.
• Use pliers to unscrew door stop and reinstall into
the 90 ° position.
I
,4
GrilleBaseWrap Ii
PinLocation
asShipped
For130°
DoorSwing
[_ CONNECTWATERSUPPLY
Connect both refrigerators to the water supplg.
• Locate and bringtubingto the frontofthe cabinet.
• Turn the water on to flushdebrisfrom line,
Run about a quart ofwater through tubing
intoa bucket,then shutoffwater.
Copper Tubing:
• Slip a 1/4 nut and ferrule (provided) over both ends
of the copper tubing Insert tube into the union fitting
on the unit and tighten nut to union
• Turn on the water to check for leaks.
GE SmartConnect TM Tubing:
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression
nut until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
I
NOTE: Hake sure excess tubing length does not
interfere with drawer closing or toekick installation.
14
Page 15
Installation Instructions
[] CONNECTPOWER
• Check to be sure the power cord is plugged
into the receptacle.
r_
6rille
I_ Raise
Electrical MasterLight
Outlet Switch
• Check to make sure power to refrigerator is on
bg opening refrigerator door to see if interior
lights are on.
• The temperature controls are preset at ]7°F
for the fresh food section and 0°F for the freezer.
• Allow 2/4hours for temperature to stabilize
before making adjustments.
Panel
1_ INSTALLTOEKICK
• Install the toekick with 4 screws provided,
one on each side and 2 in the center.
"%
IMPORTANT: The toekick must be positioned with
the vented slots on the top side. The vented toekick
must remain unobstructed for proper air circulation
and refrigerator operation.
[] STARTICEMAKER
• Flip the switch to I (ON}. The icemaker will begin
operation automaticallg.
• Be sure nothing interferes with the sweep of the
feeler arm.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to O IOFF}.
15
Page 16
49-60469
224D1234PO01
07-06 JR
Printed in the United States
NOTE: While performing installations described in this book,
safetg glasses or goggles should be worn.
For Honogram Iocalservicein gourarea, call
®
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
Monogram:
GEConsumer& hldustrial
GEAppliances
General Electric Company
Louisville, KY40225
ge com
@2006GECompany
Loading...