GE ZICP720ASBSS, ZICP720ASCSS, ZICP720ASDSS, ZICP720AXASS, ZICP720BSBSS Installation Guide

Installation

Instructions

Professional Stgle
Bottom-Freezer Refrigerators

ZICP720

Design Guide

With Installation Instructions

@

Monogram:

Safety Information

BEFOREYOUBEGIN

Readthese instructions completely and carefully.

•INPORTANT-Savetheseinstructionsfor

local inspector's use.Observeall governing codes and
ordinances.

• Note to Installer- Besureto leavetheseinstructions

with the Consumer.

• Note to Consumer- Keeptheseinstructionswith uour

Owner's Manual for future reference.

WARNING:

Thisappliance must be properlUgrounded.See"Grounding
the Refrigerator,"page6.

AVERTISSEMENT'.

Cetappareil doit _tre correctement mis 6 la terre.
Consultez<<Mise6 laterre du rdrig@rateur >>,page 6.

If Uou receiveda damaged refrigerator,Uoushould
immediately contact your dealeror builder.

CAUTION:

Dueto the weight and sizeof this refrigerator,and to reduce
the riskof personalinjurUor damage to the product-THREE

PEOPLEAREREQUIREDFORPROPERINSTALLATION.

PRUDENCE'.

Acausedu poidsetdelatailledece rdrig_ratoretpourr_duire
lerisquedeblessureetdedommages,ILFAUTTROISPERSONNES

POURFAIREL'INSTALLATIONCORRECTEMENT.

SkillLevel- Installation of this refrigerator requires

basic mechanical, carpentru and plumbing skills.Proper
installation isthe responsibilitUof the installer.Product
failure dueto improper installation is not coveredunder
the GEApplianceWarrant U.Seethe Owner's Manual for
warrant Uinformation.

WARNING:

• Theserefrigerators are top-hea% and must besecured
to preventthe possibilitUof tipping forward. Anti-Tip
protection is required.Seepages 9 and !0 for details.

• Usethis appliance only for its intended purpose.
ImmediatelUrepair or replace electricservice cords that
become fraued or damaged.
Unplugthe refrigerator before cleaning or making repairs.
Repairsshould bemade bu a qualified servicetechnician.

AVERTISSEMENT'.

• Cesrdrig@rateurssont Iourdsen haut et ilfaut les
arrimer pour @viterlear basculement. IIfaut avoir un
sgst@mede protection contre lerenversement.Voir
lesd_tails pages 9 et !0.

• IIne faut utiliser cetappareil que pour I'utilisation
appropri@e.

• R@parezou remplacezimm@diatementtout cordon
@lectriqueeffiloch@ou endommag@.

• IIfaut d@brancherlerdrig@rateuravant le nettoyage
ou toute intervention.

• Lesr@parationsdoivent@trefaites parun technicien qualifi&

For Monogram local service in gout area,
call 1.800.444.1845.

For Monogram service inCanada, call 1.888.880.3030.
For Monogram Partsand Accessories,call L800.626.2002.

www. monogram.cam

CONTENTS

Planning Guide

The Installation Space ......................3

Dimensions and Clearances ..........3

!30 ° Door Swing ..................................4

90 ° Door Swing ....................................5

Installation Instructions

Tools, Hardware, Trim,

Materials, Flooring ..............................6

Grounding the Refrigerator ............6

Step !, Remove Packaging ............7

Step 2, Install Water Lines ..............7

Step 3, Install New Side Trim ..........8

Step 4, Install Side Panels ................8

Step 5, Install Anti-Tip Brackets....9

Step 6, Install New Top Trim ........!0

Step 7, Level Refrigerator ..............!0

Step 8, Alternate Anti-Tip

Procedure ..............................!!

Step 9, Secure Refrigerator

to Cabinetrg ........................ii

2

Step !0, Install Center

Trim Strip ............................12

Step !!, Install Grille BaseCover....!2

Step 12, Remove Both Grille

Panels (if present) ..........13

Step 13, Install Grille Panel

Onto Hinges ......................13

Step 14, Adjust Door Swing ..........14

Step 15, Check and Correct

Door Alignment ..............14

Step 16, Connect Water Supplg ..!6

Step 17, Connect Power ................17

Step 18, Start Icemaker ................17

Step 19, Install Toekick ..................17

Design Guide

THE INSTALLATION SPACE

The installation space must be 71-1/2",

f 71-1/2"FinishedWidth ........................................f

ll 2-5'16" ',

"1 Wall

/k 5/'j E!ectricalf 24-3/ 6"-I View

--/ _ 6 , mm_ 6" |

!, 1 t

max I 10 i ]u .

83-I/2"tl ' 75 From

rain J_ 24"Cutout i Finished

FinishedI Depth , Floorto

• I ,, Bottomof

upenmg| _" W " 5" Electrical

I / " t aterSupply ,, WaterSupply T Area

" i I _ j

/ I, i

Z ............26 ...................\ /: ............26" .................\

3-1/2" 3-1/2"

Water And Electrical Locations

Electrical and water supply must be located

as shown.

The cutout depth must be 24"
The refrigerator will project forward, slightly

beyond adjacent cabinetry, depending on your
installation.

Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot

exceed the 24" installation depth shown. The top
case trim overlaps the bottom of the soffit.

DIMENSIONS AND CLEARANCES

71-1/2" 25-3/4"

CaseWidth CaseDepth

Shippingheight.The
refrigeratorscanbe
adjustedtofit intoa
cutoutthatis 83-1/2"
min.to84-1/2"max.

83-1/2"

atRear

72"Frame

toFrame '

28-11/16"

DepthIncluding

Handles

Product Clearances
These refrigerators are equipped with a 2-position

door stop. The factory set 130 ° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets

or walls is restricted.

25"_

Min.toi 130° Door

Wall

I

/L

Width

0 ,!

Swing Swing

H 130° Door

11

q-' '-F

i L

Notethatthetopcase

trimatthefrontis 1/2"

higherandwilloverlap
uppercabinetryor

soffit.Uselevelinglegs

andwheelsfora
maximum1"height

adjustment.

__25"__I

Min.to

Wall

/,,

,, "":::",,:::,,::::!

Additional Specifications
cA separate 115 volt 60Hz., 15 or 20 amp power

supply is recommended for each product, An
individual properly grounded branch circuit or
circuit breaker is recommended. Install properly
grounded 3-prong electrical receptacles recessed

into the back wall, Electrical must be located on
rear wall as shown,

NOTE: GFI (ground fault interrupter)is not
recommended.

Both water lines can enter the opening through

the floor or back wall. Route GE SmartConnect"
kit or 1/4" O.D. copper tubing between the cold

water line and the water connection location.
The tubing should be long enough to extend to

the front of the refrigerator. Installation of an
easily accessible shut-off valve in the water
line is required.

Allow 25" minimum clearance for a full 130° door
swing. Allow 15" for pan removal.

5" minimum clearance is required when door swing
is adjusted to 90°, Ifthe 90° door stop position is
used, pan access is maintained, but pan removal

is restricted.

See illustrations on pages
4 and 5 to determine door

swing interaction with
adjacent cabinets or
countertops,

90° Door 123-7/8"

Swing / Behind

, !, _Frame

L! i

T

!i 36-3/4-

90o.........

5" Minimumto

Wall

Refrigerator

Design Guide

23-7/8"From

Rearof

Refrigerator

Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.

Therefore, frameless cabinets mag require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.

Case

Trim

_J 1/2"

1/4"

3/4"

1-3/4" 2-3/4"

1-1/2" 2-1/2"

1-1/4"

.

2-1/4"

3/4" Overlay

Panel

",, (NominalSize)

Top View

130° DOOR SWING

(factorg setting)
Scale 1:1

Door

1-1/4"

Design Guide

- Frameless Cabinets- The
case trim overlaps cabinets

at the top and sides.

Refrigerator Therefore, frameless

J_ CaseTrim cabinets mag require

J .......... filler strips to prevent

I interference with cabinet

I door swing. The opening

t must allow for filler strips.

\ -- ] FromRearof

_°23-7/8"

i.... ',--- ',.... ,,-- 1/4

iq:i.....u

_"_._ L

I I ! ............. 1-1/2"

E_

I I ;;;;;;;;! ',
Jl ',
I I

II

I I !

I I
I I ::::} ',

I I

I I
II

Jl Door
I I I
I I I

II
I I

II '

II .......

LI i

Ill , 3/4Overlay

I] Pane

I I

Top V0ew II

90 DOOR SWING II , .........

(opbonal setting) II , u

scale 1:1 , 1-1/4"

• , ,

@ i i

II I ', '

•

II I i "

II

j i i i

i ! i

, , NominalSize

i

i i

............. 1-1/4

I

, .

5

Installation Instructions

TOOLS REQUIRED

• Tinsnips to cut banding

• Stepladder

• Bucket

• Level

• Appliance dollg
+ Tubing cutter
+ 7/16" open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 5/16",7/16" socket
Safetgglasses

1-1/4" and 1/2" open-ended wrench

• Pliers

,, !/4" ratchet or 1/4" angled wrench

HARDWARE SUPPLIED

• Water filter bgpass plug

• Anti-Tip brackets

,, 1/4"nut and ferrule

TRIM SUPPLIED

A. Soffit vent top

13. Left inside case trim

C. Right inside case trim
D. Center U-shape trim
E. Grille base wrap
F. Grille panel

G. Toekick
H. Foam spacer pads

I. Phillips screws
g. Package of 12 plastic spacers

MATERIALS REQUIRED

,, 71" long 2x4 for Anti-Tip support

• 1/4" copper water line tubing or two GE
SmartConnect +' Refrigerator Tubing kits

• Two water shut-off valves

• Screws to secure refrigerator to cabinetrg

• Stick-on hook and loop fastener strips for 1/4"
side panels

FLOORING

For proper installation, this refrigerator must be
placed on a level surface of hard material that is at
the same height as the rest of the flooring. This
surface should be strong enough to support a fullg
loaded refrigerator, or approximatelg 2,400 Ibs.

NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
refrigerator where gou are working.

A

D C

G F E <_'-

GROUNDING THE REFRIGERATOR

IMPORTANT--(Please read carefullyl

FOR PERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLYGROUNDED.

The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibilitg of electric shock hazard
from this appliance.

Have the wall outlet and circuit checked bg a
qualified electrician to make sure the outlet is
properlg grounded.

Where a standard 2-prong wall outlet is encountered,
it is gour personal responsibilitg and obligation to
have it replaced with a properlg grounded 3-prong

wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT
OR REMOVE THE THIRD

(GROUND) PRONG FROM
THE POWERCORD.

DO NOT USE AN ADAPTER PLUGTO CONNECT THE
REFRIGERATORTO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

Installation Instructions

I_1 REMOVEPACKAGING

CAUTION:Refrigeratorismuch heavierat the top than at

the bottom-be careful when moving.When using a hand truck,
handle from sideonly.

PRUDENCE:Lerdrig@ateurestbeaucoupplusIourd

enhautqu'enbas.IIfaut@treprudentIorsdesd@lacements.
Siundianeestutilis@,ilfaut souleverlerdrig@rateursurlec6t@

seulement.

• Carefully cut banding at the top and bottom, remove outer

carton.

• Slideout backcorner posts(2).

• Slidecarton off top of cabinet.
NOTE:ITISNOTNECESSARYTO LAYCABINETDOWNINORDER

TOREMOVESKID!

• Theunit is securedto the skidwith 4 slotted tie-down straps.

Removethe four 5/16" bolts from the base channels inthe
tie-downs.

• Removethe four 7/16"
bolts securingthe straps

to the skid

CAUTION:DONOT

ATTEMPTTO ROLLUNIT

Remove

Fie-Downs

./

• Support blockson the bottom of the refrigeration case must
be removed beforethe refrigerator istaken offthe skidor

damage will occur,Carefully tilt refrigerator and slideblocks
out from beneath.

• Liftthe refrigerator off the skidwith anappliance dolly.
Handlefrom the sides.

OFFSKID.

PRUDENCE:

ILNEFAUTPASESSAYER
DEFAIREROULERLE

REFRIGERATEURPOUR
L'ENLEVERDELAYPALETTE.

_1 INSTALL WATER LINES

• A cold water supply isrequired for automatic icemaker

operation.Thewaterpressuremustbebetween40and120
p.s.i.

• Route1/4" ODcopper orGESmartConnecf" plastic tubing
between housecold water line and the water connection

location.

• Tubing shouldbe long enough to extend to the front of the
refrigerator.Allow enough tubing to accommodate bend
leading into the water lineconnection.

NOTE:The only GEapproved plastictubing issuppliedin
the GESmartConnecf" Refrigerator Tubing kits.Do not use
any other plasticwater supply line because the lineisunder
pressureat alltimes. Othertypes of plasticmay crack or
rupture with age and cause water damage to your home.

GESmartConnecf" RefrigeratorTubing Kitsare available inthe
following lengths:

2'(,6m) WXO8XIO002
6'(1,8 m) WXO8XIO006

15' (4%m) WXO8X10015

25' (7.6m) WXO8X10025
Shut off the main water supply.

Turnon the nearestfaucet long enough to clearthe lineof
water.

• Install a shut-off valve betweenthe icemakerwater valve and
cold water pipe ina basement or cabinet. Theshut-off valve

should belocated where it will be easily accessible.

_jiji1[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iiiij[iii[iiiii11[iiiii{_i

\ Waterline J'

Tubing

•Turn on the main water supply and flushdebris.
Runabout a quart of water through the tubing into

a bucket. Shutoff water supply at the shut-off valve.

NOTE:Saddletype shut-off valvesare included in many water

supply kits.Before purchasing, make surea saddletype valve
complies with your local plumbing codes.

248CNRshall be adheredto. Saddlevalvesare illegal anduse

is not permitted in Massachusetts.Consultwith your licensed

NOTE:Commonwealth of MassachusettsPlumbingCodes

lumber.

Ifthe water supply to the refrigerator isfrom a Reverse

OsmosisWater System, usethe refrigerator's filter bypassplug.

Usingthe refrigerator's water filtration cartridge with the RO

filter can result inhollow ice cubes.

erBypass:

Installation Instructions

J3] INSTALL NEW SIDE TRIM

CAUTION: Handle parts with care to avoid

scratching.

• Remove the inside case trim on both refrigerators.

FoamSpacer
Pads

/

/

/

/

Applg the supplied foam spacer pads to the mating
side of one product as shown.

Remove the Phillips head screws from the inside

case trim of each product as shown. Remove and
discard side trim. Retain screws.

J_ INSTALL SIDE PANELS

Side panels must be used whenever the sides
of the refrigerator will be exposed. The i/4"
side panels will slip into the side case trim.
Secure the panels to the refrigerator with
stick-on hook and loop fastener strips. Order
the side panels from the cabinet manufacturer.

Cut a notch in the top front corner as shown
to allow clearance for corner kegs in the front

side trim.

Skip this step if gou are not using side panels.

Install new side case trim with notches toward the

bottom. Install with original screws.

* Dependingon

installationheight

Installation Instructions

151 INSTALL ANTI-TIP BRACKETS

WARNING: A.TI-TIPPRECAUTIO.S

The refrigerator is top-heavg and must be secured
to prevent the possibilitg of tipping forward.

ATTENTION : PRECAUTIONSCONTRELES

BASCULEMENTS

Le r6frig6rateur est beaucoup plus Iourd en
haut et il faut le maintenir en place pour 6viter
la possibilit6 de son basculement vers I'avant.

• Cut a 2" x 4" x 71" block and secure the block

to the mounting brackets provided using #12
or #1/4 wood screws.

2x4Cut _,

71"Length

InstallationHeight Mounting

FromFloor Bracket

[5] INSTALL ANTI-TIP BRACKETS (cont.)

• Screws must penetrate at least one inch into
vertical wall studs.

• Before pushing the refrigerator into the opening,
plug the power cord into the receptacle. Open the
grille panel and reach into the opening at the
back to grasp the power cord. Pull the power cord
into the opening as gou push the refrigerator back.

• Gentlg push refrigerator into the opening with
hands against front corners.

IMPORTANT NOTE: When the refrigerator is
installed under a soffit or if there is not enough
height for this method of security, brackets cannot
be used. Proceed to step 6 to level the refrigerator
and then to step 8 to secure refrigerator to
cabinets. The refrigerator must be secured
to prevent tipping.

Screws Mountedinto j

VerticalWallStuds

• Secure the bracket with wood block to the back
wall so that it is 84" (or gour installation height)

from the finished floor. Use #12 or #1/4 wood
screws. See illustration.

Brackets
Required

B

Soffi[ Brackets

-- Not Required

-- Beneatha
Soffit

-I

SideView

Installation Instructions

[_ INSTALLNEWTOPTRIM

• Remove 2 trim screws from the back
side of each corner. Lift off and discard

top case trims. Retain screws and
corner "L" brackets.

• Install the unified top trim by inserting
an "L" bracket into each corner.

• Install 2 screws in each "L" bracket
to secure the corners.

"L"Bracket

[_ LEVEL REFRIGERATOR

Both refrigerators MUST BE LEVEL AND PLUMB
with each other and with adjacent cabinetrg on
each side. Toekick heights should align with cabinetrg.

Both refrigerators have 4-point leveling. The front is
supported bg leveling legs, the rear is supported
bg adjustable wheels. Both are accessible from the
front of the refrigerator.

• To level the back of the refrigerator, turn the 7/26" hex

nut located above the front wheels. Turn clockwise to
raise or counterclockwise to lower the refrigerator.

• For front leveling, use a 2-2/4" open-end wrench.

• Adjust height of refrigerator to match installation

cutout opening 83-!/2 to 84-2/2". The refrigerator
should be level and plumb with cabinetrg.

• The inside case trims must align, top to bottom.

HexNutAdjusts _ll L

RearWheels _ [

LevelingLe

CAUTION:

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1". If
the installation requires more than 84-1/2" height,
the installer should elevate the refrigerator on a
sheet of plgwood or runners. Cabinetry trim could
also be added across the top of the opening to
shorten the opening. If you attempt to raise the

refrigerator more than 1", gou will damage the
front leveling legs and the rear leveling wheels.

PRUDENCE:

Les roues de nivellement arri@e et les pattes de

nivellement avant permettent un r_glage maximal
de 25 mm (1 po). Si I'ouverture pour le r_frig@ateur

a une hauteur sup@ieure _ 2,15 m (84-1/2 po),

I'installateur dolt _lever le r_frig@ateur sur une
feuille de contre-plaqu_ ou des glissi@es. II est

_galement possible d'ajouter des baguettes de
finition des placards sur le haut de I'ouverture afin

de la r_duire. Lever le r_frig_rateur de plus de

25 mm (1 po) endommage les pattes de

nivellement avant et les roues de nivellement
arri_re.

10

Installation Instructions

_1 ALTERNATE ANTI-TIP PROCEDURE

The refrigerator must be secured to prevent tipping.
The anti-tip brackets cannot be used on metal

wall studs. Use this Alternate Procedure to secure
the refrigerator against tip-over whenever metal wall

studs are encountered and there is no soffit.

• Raise the grille panel to access case trim.

• Usea 3/16" bit to drill four evenly spaced clearance
holes through the metal top case trim.

• Use a 1/16" bit to drill pilot holes through the metal
clearance holes and into the wood soffit. The holes

should be centered in the soffit or a 3/4" min. wood
brace. The brace spanning the enclosure must be

securely fastened to cabinets on both sides.

• Install four 1-1/2" drywall screws into the pilot holes.

SideView

TopCaseTrim

TopCaseTrim

InstallFour1-1/2"DrywallScrews

ThroughTrimandIntoSoffitor

3/4"Min.WoodBrace

19] SECUREREFRIGERATORTO CABINETRY

Whenever possible, perform this step for anti-tip II
security, or when anti-tip brackets cannot be used.

The refrigerator must be secured to prevent tipping.

• Raise the grille panel to access case trim.

• Drill hole in trim and drive screw through the trim -_
into adjacent cabinet.

• Follow the same procedure on the opposite side.

,I

DriveScrewsThrough

CaseTrimandInto
AdjacentCabinets

11

Installation Instructions

E_ INSTALLCENTERTRIM STRIP

• Open doors fully.

• Starting at the top, press center trim strip over the
inside case trims of both refrigerators.

• Continue pressing trim until you reach the bottom of
the case trims. The trim should align with the top and

bottom of case trims.

[] INSTALLGRILLEBASECOVER

CaseTrim

U-Shape

Trim

• Open doors fully.

• Grasp grille panel at the center and lift up to stop position.

• Remove one screw on each end of the grille base wrap.

Remove the wrap.

• Install the unified double width grille base wrap by
slipping the notched ends over the hinges.

• Install one screw on each end and 2 at the center.

UnifiedBaseWrap

_ Remove _0

Screws

PlaceTrim
OverHinges

12

Installation Instructions

[_] REMOVEBOTHGRILLEPANELS(if present)

• Remove 3 screws holding the grille panel to the
hinge on each side. Lift grille panel off the hinges.

Discard both grille panels. Retain screws.

Leave hinges in open position.
Do not push hinges back.

[_ INSTALLGRILLEPANELONTO HINGES

• Place the new unified grille panel over the hinges,
matching screw hole locations.

• Install 3 screws through each hinge and
into the bracket.

GrillePanel

Remove3 Screws

GrillePanel

• Grasp panel at the center and pull down to close.

NOTE: Check alignment of grille panel to the top of
the doors. To adjust, loosen bracket hinge screws
on all/4 hinges. Adjust and tighten screws.

Install3Screws

13

Installation Instructions

[_ ADJUSTDOORSWING

L

NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fullg to !]0 °, gou mag change the door swing to
a 90° opening. Skip this step if door opening is
satisfactory for your installation situation.

• Lift the grille panel to access the wire cover trim.

• Remove screws on both sides of the wire cover
trim and lift off.

• Use pliers to unscrew door stop and reinstall into
the 90 ° position. PinLocation

GrilleBaseWrap I_

asShipped

For130°

DoorSwing

[_ CHECKAND CORRECTDOORALIGNMENT

• Close the grille panel and both doors.

• Check to be sure the unit is level.
See Step 7 to level the unit.

• Check that the freezer drawers and bottom of doors
are horizontal and even at the lower inside corners.

• Carefully measure the inside corners to determine

if an adjustment is needed. A difference of 1/32" is

acceptable and does not require adjustment.

SKIP THIS STEP IF DOORS ARE LEVEL.

IMPORTANT: If the doors are not evenlg aligned,

theg must be removed and spacers must be installed
to raise or lower one or both doors.

Spacer

Location

\

Spacer

Location

II

/

14

[] CHECKAND CORRECTDOORALIGNMENT(cont.)

DETERMINE CORRECT SPACER

Thiskit contains 12 plasticspacers (2of each size).Match

spacerto illustration belowto besure gou have selected

the correct sizeas determined in the charts below.

L 3/32" _ 1/8"

L 5/32" L 3/16"

1/4" L 9/32"

LH Fresh Food door is higher then the RH door:

RH Fresh Food door is higher then the LH door:

'[J_ _ Dimension

A

Select and install the correct spacer on one or both
Fresh Food hinges as determined bg Dimension A.

RH Door Install Install
Dim. A LH Spacer RH Spacer

1/32" to 1/16" 1/4" no chanqe
1/16" to 3/32" 1/4" 3/16"

s/s2" to !/8" !/4" s/s2"
!/8" to 5/32" !/4" !/8"

5/32" to 3/16" 9/32" 1/8"
3/16" to 7/32" 9/32" 3/32"

Dimension

A

Select and install the correct spacer on one or both
Fresh Food hinges as determined bg Dimension A.

LH Door Install Install
Dim. A LH Spacer RH Spacer

1/32" to 1/16" no change 1/4"
1/16" to 3/32" 3/16" 1/4"

3/32" to 1/8" 5/32" 1/4"
1/8" to 5/32" 1/8" 1/4"
5/32" to 3/16" 1/8" 9/32"
3/16" to 7/32" 3/32" 9/32"

15

Installation Instructions

I_1 CHECKAND CORRECTDOORALIGNMENT(cont.)

Remove

3Screws

4. Lift door off bottom hinge pin. Place the door on a

1. Open the grille panel. Remove the grille base wrap.

2. Remove ] screws on the hinge plate.

3. Use pliers to remove door stop pin.

Liftoffandreplace
plasticspacer

protected surface; be careful not to damage the door.

5. Remove the original plastic spacer.

6. Place the selected spacer over the hinge.

7. Reverse all steps to replace the door.

[] CONNECTWATERSUPPLY

Connect both refrigerators to the water supplg. _

• Locate and bring tubing to the front of the cabinet.
Turn the water on to flush debris from line. Run

about a quartofwater through tubingintoa

bucket,then shutoffwater.

Copper Tubing:

Slip a !/4" nut and ferrule (provided) over both
ends of the copper tubing. Insert tube into the

union fitting on the unit and tighten nut to union.

Turn on the water to check for leaks.

GE SmartConnect T"Tubing:

Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression

nut until it isjust hand tight.

• Tighten one additional turn with a wrench.
Overtightening can cause leaks!

Turn on the water to check for leaks.

NOTE: Hake sure excess tubing length does not
interfere with drawer closing or toekick installation.

16

Installation Instructions

[] CONNECTPOWER

• Check to be sure the power cord is plugged
into the receptacle.

r_

6rille

I_ Raise

Electrical MasterLight

Outlet Switch

• Check to make sure power to refrigerator is on
bg opening refrigerator door to see if interior
lights are on.

• The temperature controls are preset at ]7°F
for the fresh food section and 0°F for the freezer.

• Allow 2/4hours for temperature to stabilize
before making adjustments.

Panel

1_ INSTALLTOEKICK

• Install the toekick with 4 screws provided,
one on each side and 2 in the center.

"%

IMPORTANT: The toekick must be positioned with
the vented slots on the top side. The vented toekick
must remain unobstructed for proper air circulation
and refrigerator operation.

[] STARTICEMAKER

• Flip the switch to I (ON}. The icemaker will begin
operation automaticallg.

• Be sure nothing interferes with the sweep of the
feeler arm.

• Discard the first full bucket of ice cubes.

• To turn the icemaker off, set the switch to O IOFF}.

17

Notes

18

Notes

19

49-60469-1
22401234PO01

11-o6 JR
Printed in the United States

NOTE: While performing installations described in this book,
safetg glasses or goggles should be worn.

For Honogram Iocalservicein gourarea, call

®

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance

and specifications are subject to change without notice.

Monogram:

GEConsumer& hldustrial
GEAppliances

General Electric Company
Louisville, KY40225

ge com

@2006GECompany