Page 1
Installation
Instructions
Professional Stgle
Bottom-Freezer Refrigerators
ZICP720
Design Guide
With Installation Instructions
monogram.corn
Page 2
Safety Information
BEFOREYOUBEGIN
Readthese instructions completely and carefully.
•INPORTANT-Savetheseinstructionsfor
local inspector's use.Observeall governing codes and
ordinances
• Note to Installer- Besureto leavetheseinstructions
with the Consumer
• Note to Consumer- Keeptheseinstructionswith uour
Owner's Manual for future reference.
WARNING:
Thisappliance must be properlUgrounded.See"Grounding
the Refrigerator,"page6.
AVERTISSEMENT:
Cetappareil doit _tre correctement mis a la terre.
Consultez<<Nise 0 laterre du rdrig@rateur >>,page 6.
If Uou receiveda damaged refrigerator,Uoushould
immediately contact your dealeror builder.
CAUTION:
Dueto the weight and sizeof theserefrigerators,and to
reducethe riskof personal injurUor damage to the product-
THREEPEOPLEAREREQUIREDFORPROPERINSTALLATION
PRUDENCE'.
Acausedu poidsetdelatailledecesrdrig_rateursetpourr_duire
lerisquedeblessureetdedommages,ILFAUTTROISPERSONNES
POURFAIREUINSTALLATIONCORRECTEMENT
SkillLevel- Installation of theserefrigerators requires
basic mechanical, carpentru and plumbing skills.Proper
installation isthe responsibilitUof the installer.Product
failure dueto improper installation is not coveredunder
the GEApplianceWarrantU.Seethe Owner's Manual for
warrant Uinformation.
WARNING:
• Theserefrigerators are top-hea% and must besecured
to preventthe possibilitUoftipping forward. Anti-Tip
protection is required.Seepages 9 and 12 for details.
• Usethis appliance only for its intended purpose.
ImmediatelUrepair or replace electricservice cords that
become fraued or damaged.
Unplugthe refrigerator before cleaning or making repairs.
Repairsshould bemade bUa qualified servicetechnician.
AVERTISSEMENT:
• Cesrdrig@rateurssont Iourdsen haut et ilfaut les
arrimer pour @viterleur basculement. IIfaut avoir un
sgst@mede protection contre lerenversement.Voir
lesd_tails pages 9 et 12.
• IIne faut utiliser cetappareil que pour I'utilisation
appropri@e.
• R@parezou remplacez imm@diatementtout cordon
@lectriqueeffiloch@ou endommag@.
• IIfaut d@brancherlerdrig@rateuravant le nettoyage
ou toute intervention.
• Lesr@parationsdoivent@trefaites parun technicien qualifi&
For Monogram local service in gout area,
call 1.800.444.1845.
For Monogram service inCanada, call 1.800.561.3344
For Monogram Partsand Accessories,call 1.800.626.2002.
www. monogram.corn
CONTENTS
Planning Guide
The Installation Space ......................3
Dimensions and Clearances ..........3
!30 ° Door Swing ..................................4
90 ° Door Swing ....................................5
Installation Instructions
Tools, Hardware, Trim,
Materials, Flooring ..............................6
Grounding the Refrigerator ............6
Step !, Remove Packaging ............7
Step 2, Install Water Lines ..............7
Step 5, Install New Side Trim ..........8
Step 4, Install Side Panels ................8
Step 5, Install Anti-Tip Brackets....9
Step 6, Position Refrigerator
and Install Top Trim ..........!0
Step 7, Level the Refrigerators _ii
Step 8, Alternate Anti-Tip
Procedure ..............................12
Step 9, Secure Refrigerator
to Cabinetrg ........................12
2
Step 10, Install Grille Panel ..........12
Step 11, Install Center
Trim Strip ............................!5
Step 12, Adjust Door Swing ..........!5
Step !3, Check and Correct
Door Alignment ..............14
Step 14, Install Grille BaseWrap....!7
Step !5, Connect Water Supplg ..17
Step 16, Connect Power ................18
Step 17, Start Icemaker ................18
Step 18, Install Toekick ..................18
Page 3
Design Guide
THE INSTALLATION SPACE
The installation space must be 71-1/2".
71-1/2"FinishedWidth __
_2-5/16" . ;
"F_ Electncal;_ _ 24-3/16"
_ 6" _T 6"
1O" 10,_
84-1/2"max
83-1/2"rain
Enished
Opening
Water And Electrical Locations
Electrical and water suppl 9 must be located
as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightlg
begond adjacent cabinetrg, depending on gour
installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top
case trim overlaps the bottom of the soffit.
L24"CutoutDepth
3-1/2" 3-1/2" 3-1/2" 3-1/2"
/Fq qt Fq\,:
r_ 3.1/2,,__0,,'\ .... 3.i_2,,_,c,_
WaterSupply
k
WallView
75"From
FinishedFloor
toBottomof
ElectricalArea
DIMENSIONS AND CLEARANCES
71-I/2" 25-3/4"
CaseWidth Depth
* Shippingheight.The
refrigeratorscanbe
adjustedtofit intoa
cutoutthatis 83-1/2"
rain.to 84-1/2"max.
83-1/2"
atRear
28-11/16"
DepthIncluding
Handles
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factorg set 130° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets
or walls is restricted.
_25 .... 25"_
Min.to 130° Door 130° Door Min.to
Wall Swing Swing Wall
84" Notethatthetopcase
trimatthefrontis 1/2"
higherandwilloverlap
uppercabinetryor
soffit.Uselevelinglegs
andwheelsfora
maximum1"height
adjustment.
72"Frame
toFrame
Width
0"
II
J L
Additional Specifications
• A separate 115 volt 60Hz., 15 or 20 amp power
supplg is recommended for each product. An
individual properlg grounded branch circuit or
circuit breaker is recommended. Install properlg
grounded 3-prong electrical receptacles recessed
into the back wall. Electrical must be located on
rear wall as shown.
NOTE: GFI (ground fault interrupter)is not
recommended.
• Both water lines can enter the opening through
the floor or back wall. Route GE SmartConnect"
kit or 1/4" O.D. copper tubing between the cold
water line and the water connection location.
The tubing should be long enough to extend to
the front of the refrigerator. Installation of an
easilg accessible shut-off valve in the water
line is required.
"_ / X >"
__ 11 __ __
Allow 25" minimum clearance for a full 130 ° door
swing. Allow 15" for pan removal.
5" minimum clearance is required when door swing
is adjusted to 90°. Ifthe 90° door stop position is
used, pan access is maintained but pan removal
is restricted.
See illustrations on pages
4 and 5 to determine door
swing interaction with
adjacent cabinets or
countertops.
go° Door 23-7/8"
Swing Behind
Frame
L I'
N'
i i 36-3/4"
/
90°---_ .1
5"Minimumto
Wall
Page 4
Refrigerator
Design Guide
23-7/8" From
Rearof
Refrigerator
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore frameless cabinets mag require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
Case
Trim
Door
1/4"
i
i
3/4"
1/2" ,'
i
i
i
i
1-1/2"
i
i
1-3/4"
2-1/4"
3/4" Overlay
Panel
"', /Nominal Size)
i
1-1/4"
Top View
130° DOOR SWING
(factory setting)
Scale i:I
i-1/4"
Page 5
Refrigerator
Design Guide
CaseTrim
Frameless Cabinets: The
case trim overlaps cabinets
at the top and sides.
Therefore, frameless
cabinets mag require
filler strips to prevent
interference with cabinet
door swing. The opening
must allow for filler strips.
2S-7/8"
FromRearof
Refrigerator
Top View
90° DOOR SWING
(optional setting)
Scale 2:2
Door
3/4" Overlay
Panel
(Nominal Size)
1-1/4"
Page 6
Installation Instructions
TOOLS REQUIRED
• Tinsnips to cut banding
• Stepladder
Bucket
Level
Appliance dolls
Tubing cutter
7/16" open-end wrench
#2 Phillips screwdriver
Drill and appropriate bits
• 5/16",7/16" socket
• Safetg glasses
• 1-1/4" and 1/2" open-ended wrench
• Pliers
• 1/8" ratchet or !/4" angled wrench
Tape measure
HARDWARE SUPPLIED
Water filter bgpass plug
Anti-Tip brackets
• !/4" nut and ferrule
TRIM SUPPLIED
A. Top trim
B. Left inside case trim
C. Right inside case trim
D. Center U-shape trim
E. Grille base wrap
F. Grille panel
G. Toekick
H. Foam spacer pads
I. Phillips screws (34)
J. Package of 12 plastic spacers
K. Flat metal bracket
L 2 Large screws (for metal bracket)
M. 2 Corner trim brackets
MATERIALS REQUIRED
• 71" long 2x4 for Anti-Tip support
1/4" copper water line tubing or two GE
SmartConnect T"Refrigerator Tubing kits
• Two water shut-off valves
• Screws to secure refrigerator to cabinetrg
• Stick-on hook and loop fastener strips for 1/4"
side panels
FLOORING
For proper installation, this refrigerator must be
placed on a level surface of hard material that is at
the same height as the rest of the flooring. This
surface should be strong enough to support a fulls
loaded refrigerator, or approximatelg 2,400 Ibs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
refrigerator where gou are working.
J
M
GROUNDING THE REFRIGERATOR
IMPORTANT--IPIease read carefully}
FOR PERSONAL SAFETY,THIS APPLIANCE HUST BE
PROPERLYGROUNDED,
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle
to minimize the possibilitg of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked bg a
qualified electrician to make sure the outlet is
properlg grounded.
Where a standard 2-prong wall outlet is encountered,
it is sour personal responsibilitg and obligation to
have it replaced with a properlg grounded 3-prong
wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG FROM
THE POWERCORD.
DO NOT USE AN ADAPTER PLUGTO CONNECT THE
REFRIGERATORTO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
Page 7
Installation Instructions
l_] REMOVEPACKAGING
CAUTION:Refrigeratorismuch heavier at the top than at
the bottom-be careful when moving.When using a hand truck,
handle from sideonly.
PRUDENCE:Lerdrig@ateurest beaucoupplusIourd
enhautqu'enbas.IIfaut@treprudentIorsdesd@lacements.
Siundiableestutilis@,ilfaut souleverlerdrig@rateursurlec6t@
seulement.
• Carefully cut banding at the top and bottom, remove outer
carton.
• Slideout backcorner posts(2).
• Slidecarton off top of cabinet.
NOTE:ITISNOTNECESSARYTO LAYCABINETDOWNINORDER
TOREMOVESKID!
• The unitis securedto the skidwith 4 slotted tie-down straps.
Removethe four 5/16" bolts from the base channels inthe
tie-downs.
• Removethe four 7/16"
bolts securingthe straps
to the skid.
CAUTION:DONOT
ATTEMPTTO ROLLUNIT
Remove
Tie-Downs
• Support blockson the bottom of the refrigeration case must
be removed beforethe refrigerator istaken offthe skidor
damage will occur,Carefully tilt refrigerator and slide blocks
out from beneath.
• Removethe tape from the levelinglegs.
• Liftthe refrigerator off the skidwith anappliance dolly.
Handlefrom the sides.
OFFSKID.
PRUDENCE:
ILNEFAUTPASESSAYER
DEFAIREROULERLE
REFRIGERATEURPOUR
L'ENLEVERDE LAYPALETTE
J21 INSTALL WATER LINES
• A cold water supply isrequired for automatic icemaker
operation.Thewaterpressuremustbebetween40and120
p.s.i.
• Route1/4" ODcopper orGESmartConnecf" plastic tubing
between housecold water line and the water connection
location.
• Tubing shouldbe long enough to extend to the front of the
refrigerator.Allow enough tubing to accommodate bend
leading into the water lineconnection.
NOTE:The only GEapproved plastictubing issuppliedin
the GESmartConnecf" Refrigerator Tubing kits.Do not use
any other plasticwater supply line because the lineisunder
pressureat alltimes. Othertypes of plasticmay crack or
rupture with age and cause water damage to your home.
GESmartConnecf" RefrigeratorTubing Kitsare available inthe
following lengths:
2'(.6m) WXO8XIO002
6'(1.8 m) WXO8XIO006
15' (4.6m) WXO8XIO015
25' (7.6m) WXO8XlO025
Shut off the main water supply.
Turnon the nearestfaucet long enough to clearthe lineof
water.
• Install a shut-off valve betweenthe icemakerwater valve and
cold water pipe ina basement or cabinet. Theshut-off valve
should belocated where it will be easily accessible.
\ Waterline TubingJ
•Turn on the main water supply and flushdebris.
Runabout a quart of water through the tubing into
a bucket. Shutoff water supply at the shut-off valve.
NOTE:Saddletype shut-off valvesare included in many water
supply kits.Before purchasing, make surea saddletype valve
complies with your local plumbing codes.
248CMRshallbe adheredto. Saddlevalvesare illegal and use
is not permitted in Massachusetts.Consultwith your licensed
NOTE:Commonwealth of MassachusettsPlumbingCodes
lumber.
If the water supply to the refrigerator isfrom a Reverse
Osmosis Water System, use the refrigerator's filter bypass
plug. Using the refrigerator's water filtration cartridge with
the ROfilter can result in hollow ice cubes.
\
' Filter Bypass Plug
Page 8
Installation Instructions
J_ INSTALL NEW SIDE TRIM
CAUTION: Handle parts with care to avoid
scratching.
PRUDENCE : Manipulezlespi ces
soigneusement pour 6viter de les rager.
FoamSpacer
Pads
A. Install inside case trims (B& C) with notches
toward the bottom. Install screws (I)through 5 slots
on each trim.
J4J INSTALL SIDE PANELS
Side panels must be used whenever the sides
of the refrigerator will be exposed. The 1/4"
side panels will slip into the side case trim.
Secure the panels to the refrigerator with
stick-on hook and loop fastener strips. Order
the side panels from the cabinet manufacturer.
• Cut a notch in the top front corner as shown
to allow clearance for corner kegs in the front
side trim.
Skip this step if gou ere not using side panels.
B. Applg the supplied foam spacer pads (H)to the
mating side of one product as shown.
* Dependingon
installationheight.
*84"
_'3" to 4"
2-9/16"
Page 9
Installation Instructions
[_ INSTALL ANTI-TIP BRACKETS
WARNING: ANT,-T,PPRECAUT,ONS
These refrigerators are top-heavg and must be
secured to prevent the possibilitg of tipping forward.
ATTENTION : PRECAUTIONS CONTRE LES
BASCULEMENTS
Ces r@frig6rateurs sont beaucoup plus Iourds
en haut et il faut les maintenir en place pour @viter
la possibilit@ de son basculement vers I'avant.
• Cut a 2" x 4" x 71" block and secure the block to the
mounting brackets provided using #12 or #14 wood
screws.
2x4Cut __
71"Length '_
Installation Height Mounting
FromFloor Bracket
Screws Mountedinto /_
VerticalWall Studs /
• Secure the bracket with wood block to the back wall
so that it is 84" (or gour installation height) from the
finished floor. Use #!2 or #!/4 wood screws. See
illustration.
• Screws must penetrate at least one inch into vertical
wall studs.
Brackets
Required
Brackets
Not Required
Beneatha
Soffit
BFI!so.i
SideView
IMPORTANT NOTE: When the refrigerator is installed
under a soffit or if there is not enough height for this
method of securitg, brackets cannot be used. Step 8 is
an alternate anti-tip procedure to secure refrigerator
to cabinets after it has been pushed into the final
position. The refrigerator must be secured to prevent
tipping.
Page 10
Installation Instructions
IT] POSITION REFRIGERATOR
AND INSTALL TOP TRIM
• Before pushing the refrigerators into the Approx.8"
opening, plug the power cords into the --
receptacles. Reach into the top opening
to grasp the power cord. Pullthe power
cord into the opening as gou push the
refrigerator back.
• With hands against front corners,
push one refrigerator part-wag into
the opening. The refrigerator should
be approximatelg 8" forward of the
back wall.
• Gentlg push the second refrigerator
next to the otheE The doors should be flush to each
other and the inside trims together.
• Install corner bracket (M)into each side of the
top trim (A).
• Place the top trim across the top of the refrigerators
and slip the corner brackets into the outside case
trims.
• Install 8 screws (I)through the top of the trim and
into the top case.
• Check to be sure the inside trims are aligned top
and bottom. There should be a slight gap between
the case trims.
• Install the flat metal bracket (K)between the two
machine compartments. Slip the bracket under the
inside trim. Secure the bracket using the larger screws
(L),one on each side. Leave a 3/8" gap between the
screw head and the top surface of the bracket.
I
I
II _ 3/8_'gap \
PUSH REFRIGERATORINTO OPENING
NOTE: 2 PEOPLEAREREQUIREDTO PUSHTHE UNIFIED
REFRIGERATORSINTOTHE OPENING.
• With hands against the front corners, gentlg push
the unified refrigerators into the opening or against
\
j,/
the back wall.
10
Page 11
Installation Instructions
,,,FSqLEVEL THE REFRIGERATORS • When refrigerators are level,tighten screws against the
Place a level inside the machine for each unit.
Both refrigerators MUST BE LEVELAND PLUMB with
each other and with adjacent cabinetrg on each side.
Drawers should be evenly aligned.
Both refrigerators have 4-point leveling. The front is
supported bg leveling legs, the rear is supported bg
adjustable wheels. Both are accessible from the front
of the refrigerator.
• To level the back of the refrigerator, turn the 7/16" hex
nut located above the front wheels. Turn clockwise to
raise or counterclockwise to lower the refrigerator.
For front leveling, use a 1-1/4" open-end wrench.
Adjust height of refrigerator to match installation cutout
opening 83-1/2" to 84-1/2". The refrigerator should be
level and plumb with cabinetrg.
bracket.
l]ghtenbracket
screws
CAUTION:
The rear leveling wheels and front leveling legs are limited
to a maximum height adjustment of 1". If the installation
requires more than 84-1/2" height, the installer should
elevate the refrigerator on a sheet of plgwood or runners.
Cabinetrg trim could also be added across the top of the
opening to shorten the opening. If you attempt to raise
the refrigerator more than Y', you will damage the
front leveling legs end the rear leveling wheels.
HexNutAdjusts_.[_J ....
RearWheels_ I
PRUDENCE:
Les roues de nivellement arri@e et les pattes de
nivellement avant permettent un r6glage maximal de
25 mm (! po). SiI'ouverture pour le r6frig@ateur a une
hauteur sup@ieure 6 2,!5 m (8/4-!/2 po), I'installateur doit
61everle rdrig@ateur sur une feuille de contre-plaqu_ ou
desglissi@es.IIest _galement possibled'ajouter des baguettes
de finition desplacards sur le haut deI'ouverture afin de
la r_duire. Lever le r_frig6rateur de plus de 25 mm (1 po)
endommage les pettes de nivellement event et les roues
de nivellement artiste.
11
Page 12
Installation Instructions
181 ALTERNATE ANTI-TIP PROCEDURE
The refrigerator must be secured to prevent tipping,
The anti-tip brackets cannot be used on metal
wall studs. Use this Alternate Procedure to secure
the refrigerator against tip-over whenever metal wall
studs are encountered and there is a soffit.
• Usea 3/16" bit to drill eight evenly spaced clearance
holes through the metal top case trim.
• Use a 1/16" bit to drill pilot holes through the metal
clearance holes and into the wood soffit, The holes
should be centered in the soffit or a 3/4" rain. wood
brace, The brace spanning the enclosure must be
securelg fastened to cabinets on both sides.
• Install eight (4 on each refrigerator) 1-1/2" drywall
screws into the pilot holes.
SideView
CaseTrim
TopCaseTrim
i i i i i i i i
InstallEight1-1/2"DrywallScrewsThroughTrim
andIntoSoffitor3/4"Min.WoodBrace
TopCaseTrim
191 SECURE REFRIGERATOR TO CABINETRY
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Drill hole in trim and drive screw through the trim
into adjacent cabinet.
• Follow the same procedure on the opposite side.
1_ INSTALL GRILLE PANEL
TWO PEOPLE ARE REQUIRED TO INSTALL
THE GRILLE PANEL.
• Push all four hinges on the grille panel (F) to the
open position.
• Hold the unified grille panel against the left side of the
opening. Drive 2 screws through the hinge and into the
support bracket. Install the right side hinge. Then install
the center hinges.
DriveScrewsThrough
andIntoAdjacentCabinets
J
GrillePanel
Install2
screws
• Grasp grille panel at the center and pull down to close.
The panel should align evenlg with the beveled side
of the door.
NOTE:Toadjust the grille panel backward or forward,
loosen the 2 attachment screws on all 4 hinges, Slide
the grille panel outward or to the back. Tighten the screws.
12
Page 13
Installation Instructions
[] INSTALLCENTERTRIMSTRIP
• Open doors fullg.
• The case trims should be evenlg aligned top to
bottom with a slight gap between them.
• Starting at the top, press center trim strip (D)over the
inside case trims of both refrigerators.
• Continue pressing trim until gou reach the bottom of
the case trims. The trim should align with the top and
bottom of case trims.
_] ADJUSTDOORSWING
CaseTrim
U-Shape
Trim
CIIEZEZE;°_
NOTE: This refrigerator has a 2-position door stop,
When space does not allow the door to swing open
fullg to 130°, gou mag change the door swing to
a 90° opening. Skip this step if door opening is
satisfactory for gour installation situation,
• Lift the grille panel to access the door stop.
• Use pliers to unscrew door stop and reinstall
into the 90° position.
PinLocation
For90°
DoorSwing
PinLocation
asShipped
For130°
DoorSwing
13
Page 14
Installation Instructions
[] CHECKAND CORRECTDOORALIGNMENT
• Close the grille panel and both doors.
Check that the freezer drawers and bottom of doors
are horizontal and even at the lower inside corners.
• Carefullg measure the inside corners to determine
if an adjustment is needed. A difference of !/]2" is
acceptable and does not require adjustment.
SKIP THIS STEP IF DOORS ARE LEVEL.
IMPORTANT: If the doors are not evenlg aligned,
theg must be removed and spacers must be installed
to raise or lower both doors.
Spacer
Location
\
Spacer
Location
J
I ............ I
1 ............ I
14
Page 15
Installation Instructions
[] CHECKAND CORRECTDOORALIGNMENT(cont.)
CAUTION: Follow instructions verg carefullg.
PRUDENCE : Suivezlesinstructionstr s
soigneusement
DETERMINE CORRECT SPACER
This kit contains 12 plastic spacers (2of each size). Match
spacer to illustration below to be sure gou have selected
the correct size as determined in the charts belowz
RH Fresh Food door is higher than the LH door:
'_" _l Dimension
A
Select the correct spacers to install on the Fresh Food
hinges as determined bg Dimension A.
RH Door Install Install
Dim. A LH Spacer RH Spacer
!/s2" to !/!6" !/a" s/s2"
!/16" to 3/32" !1/4" 3/16"
3/32" to 1/8" 1/4" 5/32"
1/8" to 5/32" !/4" 1/8"
5/32" to 3/16" 9/32" 1/8"
3/16" to 7/32" 9/32" 3/32"
J_ 1/4" _9/32"
LH Fresh Food door is higher than the RH door:
Dimension
A
Select the correct spacers to install on the Fresh Food
hinges as determined bg Dimension A.
LH Door Install Install
Dim. A LH Spacer RH Spacer
1/32" to 1/!6" 3/32" 1//4"
1/16" to 3/32" 3/16" 1//4"
3/32" to 1/8" 5/32" 1/4"
1/8" to 5/32" 1/8" 1/4"
5/32" to 3/16" 1/8" 9/32"
3/!6" to 7/3 2" !/4" 9/3 2"
NOTE: If this plastic spacer package is misplaced,
order WRa9X10162 for a replacement kit
15
Page 16
Installation Instructions
[] CHECKAND CORRECTDOORALIGNMENT(cont.)
Remove
Pin
f_ _ _Z4
t i J
Liftoffandreplace
plasticspacer
Remove
4Screws
1. Open the grille panel.
2. Remove/4 screws on the hinge plate.
3. Use pliers to remove door stop pin.
4. Lift door off bottom hinge pin. The door must be held
in place while spacers are being exchanged.
5. Remove the original plastic spacer.
6. Place the selected spacer over the hinge.
7. Reverse all steps to replace the door.
16
Page 17
Installation Instructions
J_ INSTALLGRILLEBASEWRAP
• Open doors fullg. Open the grille panel.
• Install the unified double width grille base wrap (E)
bg slipping the notched ends over the door hinges.
• Install one screw (I)on each end and 2 at the center.
UnifiedGrilleBaseWrap
PlaceTrim
OverHinges
[] CONNECTWATERSUPPLY
Connect both refrigerators to the water supplg.
• Locate and bring tubing to the front of the cabinet.
• Turn the water on to flush debris from line. Run
about a quart of water through tubing into a
bucket, then shut off water.
Copper Tubing:
• Slip a !/4" nut and ferrule (provided) over both
ends of the copper tubing. Insert tube into the
union fitting on the unit and tighten nut to union.
• Turn on the water to check for leaks.
GE SmartConnect" Tubing:
Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression
nut until it isjust hand tight.
Tighten one additional turn with a wrench.
Overtightening can cause leaks!
Turn on the water to check for leaks.
NOTE: Make sure excess tubing length does not
interfere with drawer closing or toekick installation.
17
Page 18
Installation Instructions
[] CONNECTPOWER
• Check to be sure the power cord is plugged
into the receptacle.
L
Grille
Panel
i aise Jl
Electrical
Outlet
• Check to make sure power to refrigerator is on
bg opening refrigerator door to see if interior
lights are on.
• The temperature controls are preset at 37°F
for the fresh food section and 0°F for the freezer.
• Allow 2/4hours for temperature to stabilize
before making adjustments.
MasterLight
Switch
I_1 INSTALLTOEKICK
• Install the toekick (G)with 4 screws (I) provided,
one on each side and 2 in the center.
I
IMPORTANT: The toekick must be positioned with
the vented slots on the top side. The vented toekick
must remain unobstructed for proper air circulation
and refrigerator operation.
[] STARTICEMAKER
• Flip the switch to I (ON}. The icemaker will begin
operation automaticallg.
• Be sure nothing interferes with the sweep of the
feeler arm.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to 0 (OFF}.
18
Page 19
Notes
19
Page 20
49-60469-2 ]
22401234PO01]
09-07 JR
Printed in the United States
NOTE: While performing installations described in this book,
safetg glasses or goggles should be worn.
If your Monogram appliance should ever require
service, you can depend on Monogram Preferred
Service. Simply call 1.800.444.1845 where our
Monogram Preferred Service Specialists are available
7 a.m. to 10 p.m. ET Monday through Friday and
8 a.m. to 6 p.m. ET Saturday and Sunday to
coordinate your service appointment.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
GE Consumer & Industrial
Appliances
General Electric Compon U
Louisville, KY 40225
ge.com
Loading...