GE ZIC360NRHLH, ZIC360NRHRH, ZICP360SLBSS, ZICP360SLCSS, ZICP360SLDSS Installation Guide

Installation
Instructions

36" Built-In Bottom-Freezer
Refrigerators

Design6uide

With InstallationInstructions

Pub.No.49-60468
PartNo.224D1145PO01

07-06JR

0

Monogram.*

Safety Information

BEFORE YOU BEGIN

Read these ins_uctions completely and carefully.

•IMPORTANT - Savetheseinstructions

for local inspector's use. Observe all governing codes
and ordinances.

• Note to Installer -- Be sure to leave these

instructions with the Consumer.

• Note to Consumer -- Keep these instructions

with your Owner's Manual for future reference.

WARNING:

This appliance must be properly grounded. See
"Grounding the Refrigerator," page 9.

AVERTISSEMENT

Cet appareil dolt 6tre correctement mis _ la terre.
Consulter, Mise fi la terre du rdfrig6rateur ,,, page 9.

If you received a damaged refrigerator, you should
immediately contact your dealer or builder.

CAUTION:

Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to

the product--THREE PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION.

PRUDENCE

A.cause du poids et de la taille de ce r6frig_rator et
pour r6duire le risque de blessure et de dommages,

IL FAUT TROIS PERSONNES POUR FAIRE
L'INSTALLATION CORRECTEMENT.

Skill Level -- Installation of this refrigerator
requires basic mechanical, carpentry and plumbing

skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation

is not covered under the GE Appliance Warranty.
See the Owner's Manual for warranty information.

WARNING:

• These refrigerators are top-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page

11 for details.

• Use this appliance only for its intended purpose.

• Immediately repair or replace electric service cords
that become frayed or damaged.

• Unplug the refrigerator before cleaning or making
repairs.

• Repairs should be made by a qualified service
technician.

AVERTISSEMENT

• Ces rdfrigdrateurs sent lourds en haut et il faut les
arrimer pour 6viter leur basculement, I] faut avoir
un syst_me de protection centre le renversement.

Voir les d6tails page 11,

• Il ne faut ufiliser cet appareil que pour l'utilisation
appropride.

• R6parer ou remplacer imm6diatement tout cordon
dlectrique effilochd ou endommag6.

• Il faut ddbrancher le r6frig6rateur avant le
nettoyage ou toute intervention.

• Les r_parations doivent 6tre faites par un
technicien qualifi6.

For Monogram local service in your area, call

1.800.444.1845.

For Monogram service in Canada, call

1.888.880.3030

For Monogram Parts and Accessories, call

1.800.626.2002.

www.monogram.com

CONTENTS

PlanningGuide

The InstallationSpace............................3

DimensionsandClearances..................3

130° DoorSwing......................................4

90° DoorSwing........................................5

CustomizationBasics..............................6

PanelDimensions....................................7

SidePanels................................................8

ZUG2GrillePanelDimensions..............8

Installation Instructions

Tools,Hardware, Materials ....................9

Groundingthe Refrigerator ....................9

Step 1, Remove Packaging ..................10

Step 2, InstallWater Line......................10

Step2A,R0 Water Line ........................11

Step 3, Install Side Panels ....................11

Step 4, Install Anti-lip Brackets ..........11

Step 5, Level Refrigerator ....................12

Step 6, Alternate Anti-Tip Procedure,,12

Step 7, Secure Refrigerator to

Cabinetry ....................................12

Step8, AdjustDoor Swing....................13

Step9, InstallGrillePanel....................13

Step10,Install FramedPanels............14

Step1OA,InstallOverlayPanels..........15

Step11,ConnectWater Supply..........16

Step12,ConnectPower........................16

Step13,Startleemaker ........................16

Step14,InstallTeekick..........................17

Design Guide

THE INSTALLATION SPACE

35-1/2'

FinishedWidth

The finished 1' [xc
cutout width [ [ _2-5/16"

must be [ 11 '_=T .

[ 1[ 10" _-Electrieal

84-1/21max_ Area

83-t/2 min

Finished

IL_24" CutoutDepth

) I

WallView

75"From

FloortoBottom

ofElectricalArea

OpeoingII

5"

2

...........

Water And Electrical Locations

Electrical and water supply must be located as shown.

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case

trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be
located on rear wall as shown.

Note: GFI (ground fault interrupter) is not
recommended.

• Water line can enter the opening through the
floor or back wall. Route GE SmartConnect TM kit or

1/4" O.D. copper tubing between the cold water
line and the water connection location. The tubing

should be long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut-off valve in the water line is required.

DIMENSIONS AND CLEARANCES

35" 25-3/8'FramedModels

CaseWidth 25-3/4'StainlessSteelModels

* Shippingheight.The

refrigeratorcanbe adjusted

to fit intoacutoutthatis

"83-1 Floorto

at TopFrame

From

I

}6"Frameto

FrameWidth

DepthIncludin Handles:

26-7/8'Frame_Models
27-3/4"StaintessSteelModels
28-11/16'professionalStyleModels

Product Clearances

These refrigerators are equipped with a 2-position door
stop. The factory set 130 ° door swing can be adjusted to
90 ° if clearance to adjacent cabinets or walls is restricted.

\

130"

Allow 25" minimum clearance for a full 130 ° door
swing. Allow 15" for pan removal.

For a 90 ° door swing, allow 4" min. clearance to a
wall, for framed and stainless steel models. Allow 5"

min. clearance for professional style models. If the
90 ° door stop position is used, pan access is maintained,
but pata removal is restricted.

See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.

83-1/2"min.to 84-1/2'max.

height.Notethat thetop

casetrim atthefrontis

1/2"higherandwill ovedap

uppercabinetryorsoffit
Uselevelinglegsandwheels

fora maximum1"height
adjustment

2Y3.7/8

9O"DoorSwing ,Fra_eBehmd

-3/4"

90" Ill "4" Stainless

_---[_L[ andFramed

•Min.DistancetoWall

models.

_1_ 5"ProSeries

ZUG2, ZUGSS2 Unified Grille Panel Kit

• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.

Note:Additional cutoutwidthmayberequired whensidepanels
are used,Addsidepanelthicknessto thefinished cutoutto
calculaterough-inwidth.

• The water and electrical locations for each product
must be located as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.

84-1/2"max

83-1/Tmin

Finished

Opening

3-1/2"

75"From

Floorto Bottom

ofElectricalArea

3-1/2"

3

Refrigerator

Design Guide

FramelessCabinets:Thecasetrim

overlapscabinetsatthetopendsides,
ThereforeframeLesscabinetsmay require
fillerstripsto preventinterferencewith

23-7/8"From

Rearof

Refrigerator

cabinetdoorswing.The openingmust

allowfor filler strips.

r

Case

Trim

1/4":

3/4"

1/2"

Top View

130 ° DOOR SWING
(factory setting)

Scale 1:1

Door

%

4

Refrigerator

Design Guide

--Case_im

FramelessCabinets:The
casetrim overlapscabinets

atthetop andsides.

Therefore,frameless

cabinetsmay requirefiller
stripsto preventinterference

with cabinetdoorswing.The

openingmust allowfor filler

strips.

23-7/8"

FromRearof

Refri .=rator

................ 1/4"

Door

.... ;---4 ..... 1/2"

3/4"Overlay

(NominalSize)

3/4"

1"

1-1/4"

- 1-1/2"

Panel

Top View
90 ° DOOR SWING

(optional setting)
Scale 1:1

5

Design Guide

CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits

Professional Style Stainless Steel Refrigerators

Stainless steel wrapped refrigerators with beveled
edges and professional style handles. These models

are shipped ready for installation.

Stainless Steel Wrapped Refrigerators

Stainless steel wrapped refrigerators with beveled
edges and tubular stainless steel handles

that coordinate with other Monogram appliances.
These models are shipped ready for installation.

Trimmed Refrigerators

Trimmed refrigerators are designed to be customized

with decorative panels. Field installed custom door

and grille panels are required.

Framed panels

You may install 1/4" thick custom panels from your

cabinet manufacturer. The decorative panel slides
into the factory installed trim. Or, order black,

white and stainless steel accessory panels from your

Monogram dealer.

Overlay panels

You may also choose to install custom overlay panels

from your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly with
surrounding cabinetry.

lyPanel

Standard ;pacerPanel
DoerHandle I/4" ThickBackerPanel

Standardsuppliedhandlesshownin314"overlay panelposition.

Door and Drawer Handles

The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom

handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels. If desired, you

may order ZKHCSS2 Monogram stainless steel tubular
handle kit for 3/4" overlay panels.

StandardDoorHandle FramedPanel

Standardsuppliedhandlesshownin1/4"panelposition.

Optional Accessory Kits

• ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels. This kit also

includes a handle side trim for custom handles.

• ZUG2: For side-by-side installation of two trimmed

bottom-freezer refrigerators. This kit provides for the
installation of a unified custom grille panel to span the

width of two units using a framed or overlay panel.

• ZUGSS2: For side-by-side installation of two stainless

steel wrapped bottom-freezer refrigerators. This kit

provides a unified stainless steel grille panel to span
the width of two units.

Side Panels

Side panels must be used whenever the sides of the
refrigerator will be exposed.

Accessory Panels

White, black and stainless steel accessory panels are
available from your Monogram dealer. Panels are cut

to size and ready to install.
ZPBC360--Black, ZPWC360-White,

ZPSC360--Stainless Steel Panels

6

Design Guide

1/4" FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must be
cut to the dimensions shown. The panels will slide
into the frame on the door, drawer and grille.

If the custom panel is less than 1/4" thick and if it
fits loosely in the door frame, it can be backed up

with a piece of filler material or foam tape to
improve the fit.

GrillePanel I_-

Panel

FreshFood I

FreeZerpanelDrawer__

FramedPanelDimensions

1/4"FramedPanel 33-7/8" 8-7/8" 46-1116" 21-7/8'

OverlayPanelDimensions

1/4"BackerPanel 33-7/8" 8-7/8" 46-1/16" 21-7/8"

0.10"SpacerPanel 32-1/2' 7-5/8" 44-11/16' 20-1/2"
3/4' OverlayPanel 34-1/8" 9" 46-5/16" 22"

I ]_5/16'

Door

I

\\

IMPORTANTNOTE:Maximumtotal panel
weight:

• Freshfood doorpanel- 58 Ibs.

• Freezerdrawerpanel- 28Ibs.

• GrillePanel- 11Ibs.

A(Width) B(Grille Height) C (FFHeight) O (FZHeight)

A (Width) B (GrilleHeight) C(FFHaight) D (FZHeight)

L Trim

Reveal

,,_--1/4"

Panel

3/4" OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides

into the trim. A spacer panel 0.10" thick must be
placed between the overlay and backer panel.

Assemble the panels with glue and screws.

• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must

be countersunk into the backer panel.

i iilPane,

il!!i

iiii_

iii

114'

Backer _ .101

Panel-- -Spacer

NOTE: Left-to-right offset is not always equal to
top-to-bottom offset.

7

IMPORTANTNOTE:Maximum

total weightfor the assembled

panels:

• Freshfood doorpanel- 58Ibs.

• Freezerdrawer panel- 28Ibs.

• GrillePanel- 11Ibs.

Design Guide

SIDE PANELS

Side panels must be used whenever the sides of the
refrigerator will be exposed. The 1/4" side panels

will slip into the side case trim. Secure the panels to

the refrigerator with stick-on hook and loop fastener
strips. Order the side panels from the cabinet

manufacturer.

• Cut a notch in the top front corner as shown to
allow clearance for corner keys in the front side

trim.

* Depending on

installation height.

"84"

ZUG2 GRILLE PANEL DIMENSIONS

The ZUG2 unified grille panel kit provides for the
installation of a framed or overlay grille panel.

I GrillePanel IT

FramedPanelDimensions

A (Width) B(Height)

1/4"Framed Panel 69-7/8" 8-7/8"

OverlayPanelDimensions

A (Width) B(Height)

1/4"Backer Panel 69-7/8" 8-7/8"

0.10"Spacer Panel 68-1/2" 7-5/8"
3/4"Overlay Panel 70-1/8" 9"

_L

Assemble the overlay panels in the same manner as

the door and drawer panels.

Installation Instructions

TOOLS REQUIRED

• Tinsnips to cut banding

• Stepladder

• Bucket

• Level

• Appliance Hand Truck

• Tubing cutter

• 7/16" open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 5/16", 7/16" socket

• Safety glasses

• 1-1/4" open end wrench

• Pliers

• 1/4" ratchet

HARDWARE SUPPLIED

• Water filter bypass plug

• Aalti-Tip brackets

• 1/4" nut and ferrule

MATERIALS REQUIRED

• 35" long 2x4 for Aalti-Tip support

• 1/4" copper water line tubing or GE
SmartConnect TM Refrigerator Tubing kits

• Water shut-offvalve

• Custom panels for fresh food door, freezer drawer
and grille panel

• Screws to secure refrigerator to cabinetry.

• Stick-on hook and loop fastener strips for

1/4" side panels

FLOORING

For proper installation, this refrigerator must be
placed on a level surface of hard material that is at

the same height as the rest of the flooring. This
surface should be strong enough to support a fully

loaded refrigerator, or approximately 1,200 lbs.
NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the
refrigerator where you are working.

GROUNDING THE REFRIGERATOR

IMPORTANT--(Please read carefully)
FOR PERSONAL SAFETy, THIS APPLIANCE MUST

BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle

to minimize the possibility of electric shock hazard
from this appliance.

Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is

proper_ grounded.

Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to

have it replaced with a properly grounded 3-prong
wall outlet.

DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD

(GROUND) PRONG FROM

THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.

9

Installation Instructions

[STEP 1] REMOVE PACKAGING

CAUTION:Refrigerator is much heavier at the

top than at the bottom - be careful when moving.
When using a hand truck, handle from side only.

PRUDENCE:Le r_frigdrateur est beancoup plus

lourd en haut qu'en bas. II faut _tre prudent lors des
ddplacements. Si un diable est utilis_, il faut soulever le

r_frig_rateur sur le c6t_ seulement.

• Carefully cut banding at the top and bottom,

remove outer carton.

• Slide out back corner posts (2).

• Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAY CABINET

DOWN IN ORDER TO REMOVE SKID!

• The unit is secured to the skid with 4 slotted
tie-tiown straps. Remove the four 5/16" bolts from

the base channels in the tie,towns.

[STEP INSTALL WATER LINE

• A cold water supply is required for automatic

icemaker operation. The water pressure must be
between 40 and 120 p.s.i.

• Route 1/4" OD copper or GE SmartConnect"

plastic tubing between house cold water line and

the water connection location.

• Tubing should be long enough to extend to the

front of the refrigerator. Allow enough tubing to
accommodate bend leading into the water line

connection,

NOTE: The only GE approved plastic tubing is
supplied in the GE SmartConnect TM Refrigerator

Tubing kits. Do not use any other plastic water supply
line because the line is under pressure at all times.

Other types of plastic may crack or rupture with age
and cause water damage to your home.

GE SmartConnect TM Refrigerator Tubing Kits are
available in the following lengths:

2' (.6 m) WX08X10002
6' (1.8 m) WX08X10006

15' (4.6 m) WX08X10015
25' (7.6 m) WX08X10025

• Remove the four 7/16"

bolts securing the straps

to the skid.

CAUTION:DoNOT

Remove

ATTEMPT TO ROLL

UNIT OFF SKID.

PRUDENCE:ILNE

FAUT PAS ESSAYER DE
FAIRE ROULER LE

owns

RI_FRIGt_RATEUR POUR
L'ENLEVER DE LAY
PALETTE.

• Support blocks on the bottom of the refrigeration

case must be removed before the refrigerator is
taken off the skid or damage will occur. Carefully,

tilt refrigerator and slide blocks out from beneath.

• Remove toekick. Set aside for final installation.

• Lift the refrigerator off the skid with an appliance
dolly. Handle from the sides.

i_l I I/_L I /

_NateriineTubing--

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into

a bucket. Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-offvalves are included in
many water supply kits. Before purchasing, make sure a

saddle type valve complies with your local plumbing
codes,

NOTE: Commonwealth of Massachusetts Plumbing [
Codes 248CMR shall be adhered to. Saddle valves are

[illegal and use is not permitted in Massachusetts.

kConsult with your licensed plumber.

1

Shut off the main water supply.
Turn on the nearest faucet long enough to clear the

line of water.

• Install a shut-offvalve between the icemaker water
vane and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

10

Installation Instructions

[STEP 2A] WATERLINE INSTALLATION

WITH A REVERSEOSMOSIS SYSTEM

Skipthisstepwhen not usinganROSystem

If the water supply to the refrigerator is from a Reverse

Osmogrs Water System use the refrigerator's filter bypass
plug. Using the refiigemtor's water filtration cartridge

with the Re filter can result in hollow ice cubes.

I

FilterBypassPlug

[STEP 3] INSTALLSIDE PANELS

Skip this step when not using side panels

If you are using 1/4" side panels, they should be inserted
into the case trim. Fasten the panels to the refrigerator

with stick-on hook and loop fastener strips before setting

refrigerator in place.

INSTALLANTI-TIPBRACKETS

WARNING: p.EcAu oNs

The refrigerator is top-heavy and must be secured to prevent
file possibility of tipping forward.

A'n'ENTION:P CAU ONSCON E

BASCULEMENTS

Le r_frig_mteur est beaucoup plus lourd en haut et IIfaut le

maintenir en place pour dviter la possibilil_ de son basculement

ve_ l'avanL

I

• Cut a 2" x 4" x 35" block and secure the block to the
mounting brackets provided using #12 or #14 wood screws.

2x4Cut _'

35'Length .. A _

l\

Installation Mounting

Height Bracket

FromFIoer

ScrewsMountedintoJ

VerticalWall Studs

• Secure the bracket with wood block to the back wall so that it
is 84" (or your installation height) from the finished teen

Use #12 or #14 wood screws. See illustration.

Brackets

Required

NotRequired

Beneatha

SideView

• Screws must penetrate at least one inch into vertical wall

studs.

• Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille panel

and reach into the opening at the back to grasp the power
cord. Pull the power cord into the opening as you push the

refrigerator back.

• Gendy push refrigerator into the opening with hands against
front comers.

ImportantNote:Whentherefrigeratorisinstalledunderasoffitorifthereisnot
enoughheightforthismethodofsecurity,bracketscannotbeused.Proceedtostep5

toleveltherefrigeratorandthentostepBtosecurerefrigeratortocabinets.The
refrigeratormustbesecuredtopreventtipping.

11

Installation Instructions

ISTEP LEVEL REFRIGERATOR

All models have 4-point leveling. The front is
supported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible from the front
of the refrigerator.

• To level the back of the refrigerator, turn the
7/16" hex nut located above the front wheels. Turn

clockwise to raise or counterclockwise to lower the
refrigerator.

• For front leveling, use a 1-1/4" open-end wrench.

• Adjust height of refrigerator to match installation
cutout opening 83-1/2 to 84-1/2". The refrigerator
should be level and plumb with cabinetry.

RearWheels

LevelingLeg

CAUTION:

The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the

installer should elevate the refrigerator on a sheet of
plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator
more than 1", you will damage the front leveling legs
and the rear leveling wheels.

ISTEP 6-] ALTERNATE ANTI-TIP

PROCEDURE

The refrigerator must be secured to prevent tipping.
The anti-tip brackets cannot be used on metal wall

studs. Use this Alternate Procedure to secure the
refrigerator against tip-over whenever metal wall studs

are encountered and there is no soffit.

SideView /

Top/CaseTrim _ U

i i 71 -

InstallFour

1-1/2' Dr,hvallScrews

ThroughTrimandIntoSoffit

or3/4" Min.WoodBrace

• Raise the grille panel to access case trim.

• Use a 3/16" bit to drill four evenly spaced clearance

holes through the metal top case trim.

• Use a 1/16" bit to drill to pilot holes through the
metal clearance holes and into the wood soffit. The

holes should be centered in the soffit or a 3/4" rain.
wood brace. The brace spanning the enclosure must

be securely fastened to cabinets on both sides.

• Install four, 1-I/2" drywall screws into the pilot holes.

PRUDENCE

Les roues de nivellement arri6re et les pattes de
nivellement avant permettent un r6glage maximal
de 25 mm (1 po). Si l'ouverture pour le r6frig6rateur
a une hauteur sup6rieure fi 2,15 m (84-1/2 po),
l'installateur dolt 6lever le r6frig6rateur sur une
feuille de contre-plaqu6 ou des glissi6res. II est
6galement possible d'ajouter des baguettes de
linition des placards sur le haut de l'ouverture afin

de la r6duire. Lever le rffrig6rateur de plus de
25 mm (1 po) endommage les pattes de nivellement

avant et les roues de nivellement arri6re.

[STEP SECURE REFRIGERATOR

TO CABINETRY

Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.

• Raise the grille panel to access case trim.

• Drill hole in trim and drive screw through the trim

into adjacent cabinet.

• Follow the same procedure on the opposite side.

DriveScrews

ThroughCaseTrimandInto

AdjacentCabinets

12

Installation Instructions

[STEP 81ADJUST DOOR SWING

NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open

fully to 130 °, you may change the door swing to a 90°
opening. Skip this step if door opening is satisfactory

for your installation situation.

• Lift the grille panel to access the wire cover trim.

• Remove screws on both sides of the wire cover trim
and lift off.

• Use pliers to unscrew door stop and reinstall into
the 90 ° position.

I I

PinLocationFor

PinLocation
130° DoorSwing

as Shipped

[STEP 9] INSTALL GRILLE PANEL

• Raise the grill panel to stop position.

I

LoosenI_

_ioe I
Trim ',

Screw

• Loose screws on side trim behind frame. Remove
bottom trim.

• Slide panel over the metal baker panel and into the

trim.

• If necessary, tap with a wood block until panel slips
under the top trim piece.

• Reassemble bottom trim. Tighten screws.

• Adjust the hinge spring to accommodate the panel
weight, if necessary.

__ P_

AdjustNutBelow

Springto Accommodate

PanelWeight

GrilleJ_

Loosen

Side
Trim

Screw

• Reinstall the wire cover trim.

13

Installation Instructions

[STEP 10] INSTALL 1/4" FRAMED

PANELS

Handle

Trim

•UseFrontHoles
to SecureTrim

UseRearHoles

toSecureHandle

Standardsuppliedhandleshown

Right hand models shown. Use the same instructions

for left hand models.

IF YOU ARE INSTALLING OVERLAY PANELS,

GO TO STEP 9A.

Refrigerator

Door

in1/4"panelposition.

Install door and drawer panels:

• Open door to 90°. Remove the 4 Phillips head screws
from the door handle.

• Remove handle. Retain all screws.

• Remove 4 screws holding trim, lift off trim.
Retain screws.

• Slide framed panel into the door trim.

• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original

screws in the FRONT screw holes,

• Secure the handle to the door using the REAR screw
holes.

• Follow the same procedures to install the drawer panel.

14

Installation Instructions

ISTEP 10A IINSTALL OVERLAY

PANELS

Handle
Trim

-UseFrontHoles

to SecureHandle

UseRearHoles
to SecureTrim

Move

Forward

For3/4'

Panel

Suppliedhandleshowninthe

overlaypanelposition.

Right hand models shown. Use the same instructions

for left hand models.

trTrim

i i i i

Refrigerator

Doer

Install door and drawer panels:

• Open door to 90 °. Remove the 4 Phillips head screws

from the door handle.

• Remove handle. Retain all screws.

• Remove 4 screws holding trim, lift off trim.

Retain screws.

• Slide overlay panel into the door trim.

Custom handles
If you are using custom handles, the handle must be

properly secured to the panel before sliding the panel
into the trim.

• The cabinet manufacturer will supply the custom
handle and hardware.

• Secure the door/drawer trim using both the FRONT
and REAR screw holes. Discard supplied handle.

• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original

screws in the REAR screw holes.

• Secure the handle to the door using the FRONT screw

holes.

• Follow the same procedures to install the drawer panel.

15

Installation Instructions

[STEP 11 ICONNECT WATER SUPPLY

House Refrigerator

WaterSupply WaterSupply

• Locate and bring robing to the front of the cabinet.

• Turn the water on to flush debris from line. Run
about a quart of water through tubing into a bucket,

then shut off water.

Copper Tubing:

• Slip a 1/4" nut and ferrule (provided) over both
ends of the copper tubing. Insert tube into the

union fitting on the unit and tighten nut to union.

• Turn on the water to check for leaks.

[STEP 121 CONNECT POWER

• Check to be sure the power cord is plugged into
the receptacle.

I

Raise _i

Grille11

Paner_'

:at_

Electrical MasterLight

Outlet Switch

• Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights

are on.

• The temperature controls are preset at 37°F

for the fresh food section and O°F for the freezer.

• Allow 24 hours to stabilize before making

adj ustlTxen ts.

[STEP 13] START ICEMAKER

I

GE SmartConnect TM Tubing:

• Insert the molded end of the robing into the
refrigerator connection. Tighten the compression

nut until it is just hand tight.

• Tighten one additional turn with a wrench.
Overtightening can cause leaks!

• Turn on the water to check for leaks.

Note: Make sure excess tubing length does not

interfere with drawer closing or toekick installation.

• Flip the switch to I (ON). The icemaker will begin
operation automatically.

• Be sure nothing interferes with the sweep of the
feeler arm.

• Discard the first full bucket of ice cubes.

• To turn the icemaker off, set the switch to O (OFF).

16

Installation Instructions

ISTEP 141 INSTALL TOEKICK

• Locate the supplied toekick (shipped taped to
the side of the refrigerator). Install with 2 screws

provided, adjust to desired height and tighten

screws.

• A custom toekick can be installed to match or
complement the surrounding cabinetry. Use the

supplied toekick as a template to cut out the notch
and vent holes.

SuppliedToekick

Important: The vented toekick must remain
unobstructed for proper air circulation and

refrigerator operation.

17

Notes

18

Notes

19

NOTE:While performinginstallationsdescribedinthis book,
safetyglassesor gogglesshouldbeworn.

For Monogram ®local service in your area, call

1. 800. 444.1845.

NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance

and specifications are subject to change without notice.

Monogram:

GEConsmnet& Industlia/
GEApp/18nces

Genera/Bectrlc Company
L_uisv_/e, KY40225

Oe.com