GE ZIC360NXDLH, ZIC360NXDRH, ZICP360NHALH, ZICP360NHARH, ZICP360NXCLH Installation Guide

Design Guide with

Installation

Instructions

36" Built-In Bottom Freezer
Refrigerators

Pub, No, 49-60706-1
Part No, 224D3735PO01

03-14 GE

monogram,corn

Safety Information

BEFOREYOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT- Savetheseinstructions

for local inspector's use, Observe all governing codes
and ordinances,

• Note to Installer - Besure to leave these

instructions with the Consumer,

• Note to Consumer - Keep these instructions

with your Owner's Manual for future reference,

WARNING:

This appliance must be properly grounded, See
"Grounding the Refrigerator," page 9,

AVERTISSEMENT

Cet appareil dolt 6tre correctement mis _ la terre,
Consulter <<Mise _ la terre du refrigerateur >>,page 9,

If you received a damaged refrigerator, you should
immediately contact your dealer or builder,

CAUTION:

Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product--THREE PEOPLE ARE REQUIRED FOR PROPER

INSTALLATION,

PRUDENCE

A cause du poids et de la taille de ce refrigerator et
pour reduire le risque de blessure et de dommages, IL

FAUT TROIS PERSONNES POUR FAIRE L'INSTALLATION
CORRECTEMENT,

Skill Level -Installation of this refrigerator requires

basic mechanical, carpentry and plumbing skills,

Proper installation is the responsibility of the installer,

Product failure due to improper installation is not
covered under the GE Appliance Warranty, See the
Owner's Manual for warranty information,

WARNING:

. These refrigerators are top-heavy and must

be secured to prevent the possibility of tipping
forward, Anti-Tip protection is required, See page 11
for details,

. Use this appliance only for its intended purpose,

. Immediately repair or replace electric service cords

that become frayed or damaged,

. Unplug the refrigerator before cleaning or making

repairs,

. Repairs should be made by a qualified service

technician,

AVERTISSEMENT

. Ces refrigerateurs sont Iourds en haut et il faut

les arrimer pour eviter leur basculement, II faut avoir
un systeme de protection contre le renversement,

Voir les details page 11,

. II ne faut utiliser cet appareil que pour I'utilisation

appropriee,

. Reparer ou remplacer immediatement tout cordon

electrique effiloche ou endommage,

. II faut debrancher le refrigerateur avant le nettoyage

ou toute intervention,

. Les reparations doivent 6tre faites par un technicien

qualifie,

For Monogram local service in your area, call

1.800.444.1845.
For Monogram service in Canada, call

1.800.561.3344
For Monogram Parts and Accessories, call

1.800.626.2002.
www. monogram.corn

CONTENTS

Planning Guide

The Installation Space ..............................3

Dimensions and Clearances .................3

130 ° Door Swing .........................................4

90 ° Door Swing ............................................5

Customization Basics ...............................6

Panel Dimensions .......................................7

Side Panels ....................................................8

ZUG2 Grille Panel Dimensions ..............8

Installation Instructions

Tools, Hardware, Materials ....................9

Grounding the Refrigerator ...................9

Step 1, Remove Packaging .................10

Step 2, Install Water Line .....................10

Step 2A, RO Water Line ........................11

Step 3, Install Side Panels ....................11

Step 4, Install Anti-Tip Brackets ........11

Step 5, Level Refrigerator ....................13

Step 6, Secure Refrigerator to

Cabinetry .....................................13

Step 7, Adjust Door Swing ...................14

Step 8, Install Grille Panel ....................14

Step 9, Install Framed Panels ............15

Step 9A, Install Overlay Panels ..........16

Step 10, Connect Water Supply .......17

Step 11, Connect Power .......................17

Step 12, Start Icemaker ........................17

Step 13, Install Toekick .........................18

Design Guide

THE INSTALLATION SPACE

35-1/2"

FinishedWidth

The finished
cutout width
must be

35-1/2",

84-1/2"max
83-1/2"min

Finished

Water And Electrical Locations

Electrical and water supply must be located as shown,

The cutout depth must be 24"
The refrigerator will project forward, slightly beyond

adjacent cabinetry, depending on your installation,
Allow minimum 1/8" air gap between case back & wall,

Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot exceed

the 24" installation depth shown, The top case trim
overlaps the bottom of the soffit,

Additional Specifications
, A 115 volt 60Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or circuit
breaker is recommended, Install

a properly grounded 3-prong electrical receptacle
recessed into the back wall, Electrical must be located

on rear wall as shown,

Note: GFI (ground fault interrupter)is not recommended,
. Water line can enter the opening through the floor

or back wall, Route GE SmartConnect TM kit or 1/4" O,D,
copper tubing between the cold water line and the

water connection location, The tubing should be
long enough to extend to the front of the refrigerator,

Installation of an easily accessible shut-off valve in the

water line is required,

I_2-5/16" I_ WallView

II m e,, II

I"t 24"CutoutDepth I I 75"From
I I I I FloortoBottom

I I WaterSupply It ofElectricalArea

113-1/2"/ \, 3-1/2"H I

3-1/2"

DIMENSIONS AND CLEARANCES

35"

CaseWidth

"83-1/2"

at

Rear

DepthIncludingHandles:
26-7/8"FramedModels

27-3/4"StainlessSteelModels
28-11/16"ProfessionalStyleModels

Product Clearances

These refrigerators are equipped with a 2-position door

stop, The factory set 130 ° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted,

130°DoorSwing , MinimUmtoWall

i

I [

130°

Allow 25" minimum clearance for a full 130° door

swing, Allow 15"for pan removal,
For a 90 ° door swing, allow 4" min, clearance to a wall,

for framed and stainless steel models, Allow 5" min,

clearance for professional style models, If the 90° door
stop position is used, pan access is maintained, but pan

removal is restricted,
See illustrations pages 4 and 5 to determine door swing

interaction with adjacent cabinets or countertops,

25-3/8"FramedModels
25-3/4"StainlessSteelModels
CaseDepth

*84"From cutout that is 83-1/2"
Floorto min, to 84-1/2" max,

TopFrame height, Note that the top

J case trim at the front is

. 1/2" higher and will

- overlap upper cabinetry

........ 36"Frameto

FrameWidth

, 25"--

Shipping height, The
refrigerator can be
adjusted to fit into a

or soffit, Use leveling
legs and wheels for a
maximum 1" height
adjustment,

t

23-7/8"

90°DoorSwing Behind

L i']

..... 136-3/4",

90

o I j *4 Stainless

.... i , andFramed

. -- 5 ProSeries

Min.Distanceto Wall

Frame

1

i / -

• _ ,,m°dels.

ZUG2, ZUGSS2 Unified Grille Panel Kit

. If you are installing two refrigerators, side by side,

the installation space must be 71-1/2"wide,

Note: Additional cutout width may be required when side
panels are used, Add side panel thickness to the finished

cutout to calculate rough-in width,

. The water and electrical locations for each product

must be located as shown,

o A separate 115V, 60Hz., 15 or 20 amp power supply is

recommended for each product,

Refrigerator

Design Guide

23-7/8"From

Rearof

Refrigerator

3/4"

1/2"

Frameless Cabinets: The case trim
overlaps cabinets at the top and sides,

Therefore, frameless cabinets
may require filler strips to prevent

interference with cabinet door swing,
The opening must allow for filler strips,

.... -'-.... 1/2"

i ..... 3/4"

1 ,F

Top View

130° DOOR SWING

Door

3/4" Overlay

Panel

NominalSize

"4

4

i!ii!i_!,,

........................i-1/4"

(factory setting)
Scale 1:1

Refrigerator

Design Guide

_Case _im

Frameless Cabinets:
The case trim overlaps

cabinets at the top and
sides, Therefore, frameless

cabinets may require
filler strips to prevent

interference with cabinet
door swing, The opening

must allow for filler strips,

23-7/8"

FromRearof

Refricerator

u
u u u u

.... 1/4"

u u u u
u u u u
u u u u

' ' ' -- 1/2"

Door

' 3/4"

u
u
u

u ......... 1"

,,

3/4" Overlay

Panel

(NominalSize)

Top View
90° DOOR SWING

(optional setting)
Scale 1:1

1-1/4"

Design Guide

CUSTOMIZATION BASICS:

Framed Or Overlay Panels, Custom Handles and Accessory Kits

Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators with beveled edges
and professional style handles, These models are shipped
ready for installation,

Stainless Steel Wrapped Refrigerators
Stainless steel wrapped refrigerators with beveled edges

and tubular stainless steel handles that coordinate with
other Monogram appliances, These models are shipped

ready for installation,

Trimmed Refrigerators
Trimmed refrigerators are designed to be customized with
decorative panels, Field installed custom door and grille
panels are required,

Framed panels
You may install 1/4"thick custom panels from your
cabinet manufacturer, The decorative panel slides into the
factory installed trim, Or, order black, white and stainless
steel accessory panels from your Monogram dealer,

Overlay panels
You may also choose to install custom overlay panels from
your cabinet manufacturer, This design provides
a seamless appearance which integrates smoothly
with surrounding cabinetry,

J

i 3/4"Overlay Panel

i

.............Standard

Door Handle

Standard supplied handles shown in 3/4" overlay panel position,

Door and Drawer Handles
The standard supplied handles can be adjusted to

accommodate both framed or overlay panels, Custom
handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels, If desired, you may
order ZKHCSS2 Monogram stainless steel tubular handle
kit for 3/4" overlay panels,

...... .I0" Thick Spacer Pan_

..............I/4" Thick Backer Pan

Standard Door Handle Framed Panel

Standard supplied handles shown in 1/4" panel position,

Optional Accessory Kits
. ZKHCSS2: Honogram Tubular Stainless Steel handles

designed to fit 3/4" overlay panels, This kit also includes
a handle side trim for custom handles,

. ZKHPSS!: Professional Tubular Stainless Steel Handle

designed to fit 3/4" overlay panels, Kit includes one
handle, Order 2 kits for bottom-freezer refrigerators from

your Monogram supplier,

. ZUG2: For side-by-side installation of two trimmed

bottom-freezer refrigerators, This kit provides for the
installation of a unified custom grille panel to span the

width of two units using a framed or overlay panel,

Side Panels
Side panels must be used whenever the sides of the

refrigerator will be exposed,

. ZUOPP2: For side-by-side installation of two professional-

style bottom-freezer refrigerators, This kit provides a
unified stainless steel grille panel to span the width of

two units,

. ZUGSS2: For side-by-side installation of two stainless

steel wrapped bottom-freezer refrigerators, This kit
provides a unified stainless steel grille panel to span

the width of two units,

. ZKHCT: Handle side trim for left-hand and right-hand

doors, For use on 3/4" custom panels when using a
custom handle,