GE ZIC360N RH, ZICS360N RH, Monogram ZIC360NRH, Monogram ZICS360NRH, Monogram ZICS360NLH Design & Installation Manual
Page 1
Installation
Instructions
ZIC360NRH,ZIC360NLH,
ZICS360NRH,ZICS360NLH
Built-In Bottom-Freezer
Refrigerators
Design Guide
With Installation Instructions
Q
Monogram;'
We bring good things to life
Page 2
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT Save these instructions for
local inspector's use. Observe all governing
codes and ordinances.
• Note to Installer- Be sure to leave these instruc-
tions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner's Manual for future reference.
WARNING:
This appliance must be properly grounded. See
"Grounding the Refrigerator," page 9.
AVERTISSEMENT
Cet appareil dolt 6tre correctement mis _ la terre.
Consulter <<Mise a la terre du rOfrigerateur _, page 9.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product- TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
PRUDENCE
tk cause du poids et de la taille de ce refrigerateur et
pour reduire le risque de blessure et de dommages, IL
FAUT DEUX PERSONNES POUR FAIRE
L'INSTALLATION CORRECTEMENT.
Skill Level - Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the in-
staller. Product failure due to improper installation is
not covered under the GE Appliance Warranty. See
the Owner's Manual for warranty information.
WARNING:
• These refrigerators are top-heavy and must be
secured to prevent the possibility of tipping for-
ward. Anti-Tip protection is required. See page 11
for details.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
AVERTISSEMENT
• Ces refrigerateurs sent lourds en haut et il faut les
arrimer pour eviter leur basculement. II faut avoir
un syst_me de protection centre le renversement.
Voir les details page 11.
• Ii ne faut utiliser cet appareil que pour l'utilisation
appropriee.
• Reparer ou remplacer immediatement tout cordon
electrique effiloche ou endommage.
• Ii faut debrancher le refrigerateur avant le
nettoyage ou toute intervention.
• tes reparations doivent Otre faites par un
technicien qualifie.
For Monogram local service ill your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call
1-800-626-2002.
www. monogram.com
CONTENTS
PlanningGuide
TheInstallationSpace....................................3
DimensionsandClearances..........................3
130° DoorSwing..............................................4
90° DoorSwing................................................5
CustomizationBasics.....................................6
PanelDimensions............................................7
Side Panels .......................................................8
ZUG2GrillePanel Dimensions......................8
Installation Instructions
Tools,Hardware, Materials ...........................9
Grounding the Refrigerator............................9
Step 1, RemovePackaging ..........................10
Step 2, Install Water Line .............................10
Step 2A, ROWater Line ................................11
Step 3, Install Side Panels ...........................11
Step 4, Install Anti-lip Brackets .................11
Step 5, Level Refrigerator ............................12
Step 6, Secure Refrigerator to Cabinetry ..12
Step 7, Adjust DoorSwing ...........................13
Step 8, Install Grille Panel ............................13
Step 9, Install FramedPanels......................14
Step 9A, Install Overlay Panels ...................15
Step I0, Connect Water Supply ..................16
Step 11,Connect Power ...............................16
Step 12,Start Icemaker ................................16
Step 13,Install Toekick.................................16
2
Page 3
Design Guide
THE INSTALLATION SPACE
The finished
cutout width
must be
35d/2".
84-1/2"max
83-1/2"min
Finished
T
35-1/2"
_FinishedWidth_
10" _'_ Electrical
Area
¢
24"CutoutDepth
11/2" 31/2_
WallView
74-1/2"From
Floorto Bottom
of Electrical
Water And Electrical Locations
Electrical and water supply must be located as shown.
The cutout depth must be 24"
Designed for industry standard flush installation. The
refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
, A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
Note: GFI (ground fault interrupter) is not
recommended.
• Water line can enter the opening through the floor
or back wall. The water line should be 1/4" O.D.
copper tubing between the cold water line and
water connection location, long enough to extend
to the front of the refrigerator. Installation of an
easily accessible shut off valve in the water line is
recommended.
38"
CaseWidth
DIMENSIONS AND
CLEARANCES
* Shippingheight,The
*84" From refrigeratorcanbeadjusted
Floorto to fit into a cutoutthat is
TopFrame 83-1/2"min,to 84-1/2"max,
height.Notethat the topcase
trim atthefront is 1/2"higher
andwill overlapupper
cabinetryorsoffit. Use
levelinglegsandwheelsfor
heightadjustment.
Frameto Frame
Width
Product Clearances
These refrigerators are equipped with a 2 position
door stop. The factory set 130 ° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets or
walls is restricted.
130° Door Swing
25"_
Minimum
, to Wall
I \\
,k k,
X X, k,
X
X,
X,
\,\\,\\
130°....... ..Y
90° Door Swing
Behind
il 'Fr3iame
i ii
-3/4"
'S
90°.........
Allow 25" minimum clearance for a full 4" Minimum
130 ° door swing. Allow 15" for pan removal, to Wall
4" minimum clearance is required when door swing
is adjusted to 90 °. If the 90 ° door stop position is
used, pan access is maintained, but pan removal is
restricted.
See illustrations pages 4 and 5 to determine door
swing interaction with adjacent cabinets or
countertops.
ZUG2, ZUGSS2 Unified Grille Panel Kit
, If you are installing two refrigerators, side by side,
the installation space must be "/1-1/2" wide.
Note: Additional cutout width maybe required when side panels
are used. Add side panel thickness to the finished cutout to
calculate rough-in width.
• The water and electrical locations for each product
must be located as shown.
• A separate l15V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
q_ 71d/2"FinishedWidth
84q/2"max
83q/2"min
Finished
2-5/16" i
_Electrical _ _ 24-3/16"
IF7" : IFT'
18" 10"
L24"Cutout
Depth
Opening 5) WaterSupply
i
_ 26"_ _ 26"_
3-1/2"
WallView
74-112"From
F[{)orto Bottom
of[[ectrical
M/2"
3
Page 4
Design Guide
Refrigerator
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
\
23-7/8"From
Rearof
Refrigerator
FramelessCabinets:The case trim
overlaps cabinets atthe to ) andsides.
Therefore, frameless cabinets may
require filler strips to prevent inter-
ference with cabinet door swing. The
opening mustallow for filler strips.
Case
Trim
3/4"
1/2"
1/4"
2 _
1-3/4"
i
1-1/2" :
1-1/4"
2-3/4"
2-1/2"
2-1/4"
3_
", 3/4"Overlay
', Panel
/ominal Size
Door
Top View
130 ° DOOR SWING
(factory setting)
Scale 1:1
Page 5
Design Guide
Refrigerator
\
\
\
\
\
\
\
\
\
\
\
\
\
\
Top View
90 ° DOOR SWING
(optional setting)
Scale 1:1
\
\
\
\
\
\
\
\
\
\
Door
_Case _im
FramelessCabinets:The
case trim overlaps cabinets
at the top and sides.
Therefore, frameless
cabinets may require filler
strips to prevent inter-
ference with cabinet door
swing. The opening must
allow for filler strips.
23-7/8"
FromRearof
Refri_erator
r
I
i i i
.... 1/2
3/4'_
I I
1-1/4"
1-1/2"
3/4" Overlay
Panel
(NominalSize)
1-1/4"
Page 6
Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Models Available
Stainless Steel Wrapped Models:
ZICS360N RH (right-handed door)
ZICS360N LH (left-handed door)
Trimmed models:
ZIC360N RH (right-handed door)
ZIC360N LH (left-handed door)
Overlay panels
You may also choose to install custom overlay panels
from your cabinet manufacturer. This design provides a
seamless appearance which integrates smoothly with
surrounding cabinetry.
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shipped
ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door and
grille panels are required.
DoorHandle 1/4" ThickBackerPanel
Standard supplied handles shown in 3/4"overlay panel position.
Framed panels
You may install 1/4" thick custom panels from your
cabinet manufacturer. The decorative panel slides into
the factory installed trim. Or, order black, white and
stainless steel accessory panels from your Monogram
dealer.
Door and Drawer Handles
The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom
handles of your choice, supplied by your cabinet maker
can also be installed. If desired, you may order ZKHCSS2
Monogram stainless steel tubular handle kit for overlay
panels.
Side Panels
Side panels must be used whenever the sides of the
refrigerator will be exposed.
StandardDoorHandle FramedPanel
Standardsupplied handles shown in 114"panel position.
Optional Accessory Kits
, ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit overlay panels.
• ZUG2: For side by side installation of two trimmed
bottom-freezer refrigerators. This kit provides for the
installation of a unified custom grille panel to span the
width of two units using a framed or overlay panel.
• ZUGSS2: For side by side installation of two stainless
steel wrapped bottom-freezer refrigerators. This kit
provides a unified stainless steel grille panel to span
the width of two units.
Accessory Panels
White, black and stainless steel accessory panels are
available from your Monogram dealm: Panels are cut to
size and ready to install.
ZPBC360-Black, ZPWC360-White,
ZPSC360-Stainless Steel Panels
6
Page 7
Design Guide
1/4" FRAMED PANEL DIMENSIONS
If you choose to install framed panels, they must be
cut to the dimensions shown. The panels will slide
into the frame on the door, drawer and grille.
If the custom panel is less than 1/4" thick and if it fits
loosely in the door frame, it can be backed up with a
piece of filler material or foam tape to improve the fit.
IMPORTANT NOTE: Maximum weight for fresh
food panel is 50 pounds and 30 pounds for freezer
drawer panel.
I Door/Drawer
I
I
I
I
k
\
1 5/16,'
L Trim
Reveal
1/4"
Panel
F eshFood
Panel
FramedPanel Dimensions
A (Width) B (GrilleHeight) C (FFHeight) D (FZHeight)
114"FramedPanel 33-7/8" 8-7/8" 46-1/16" 21-7/8"
OverlayPanel Dimensions
A (Width) B (Grille Height) C (FFHeight) D (FZHeight)
1/4"Backer Panel 33-718" 8-7/8" 46-1/16" 21-718"
0.1if' Spacer Panel 32-112" 7-5/8" 44-11/16" 20-112"
3/4"Overlay Panel 34-118" 9" 46-5/16" 22"
3/4" OVERLAY PANEL DIMENSIONS
For a more custom appearance, overlay panels may be
installed on trimmed models. The overlay panel must
be secured to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.10" thick must be placed
between the overlay and backer panel.
IMPORTANT NOTE: Maximum total weight for
assembled fresh food panel is 50 pounds and 30
pounds for freezer drawer panel.
Assemble the panels with glue and screws.
* Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
* Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must be
countersunk into the backer panel.
Door/Drawer
1/4"
Backer
Panel
3veda
Panel
_,10 Inc
Spacer
_acker Panel!
NOTE: Left-to-right offset is not always equal to
top-to-bottom offset.
7
Page 8
Design Guide
SIDE PANELS
Side panels must be used whenever the sides of the
refrigerator will be exposed. The 1/4" side panels will
slip into the side case trim. Order the side panels
from the cabinet manufacturer.
* Depending on
installation height.
*84"
2-9/16"
ZUG2 GRILLE PANEL DIMENSIONS
The ZUG2 unified grille panel kit provides for the
installation of a framed or overlay grille panel.
A
GrillePanel ]
_L
FramedPanel Dimensions
A(Width) B(Height)
1/4"Framed Panel 69-7/8" 8-7/8"
Overlay PanelDimensions
A(Width) B(Height)
1/4"Backer Panel 69-7/8" 8-7/8"
0.10'Spacer Panel 68-1/2" 7-5/8"
314"Overlay Panel 70-118" 9"
i i i
Assemble the overlay panels in the same manner as
the door and drawer panels.
Page 9
Installation Instructions
TOOLS REQUIRED
• Tinsnips to cut banding
• Stepladder
• Bucket
• Level
• Appliance Hand Truck
• Tubing cutter
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16", 7/16" socket
• Safety glasses
• 1-1/4" open end wrench
• Pliers
HARDWARE SUPPLIED
• Water filter bypass plug
• Anti-Tip brackets
• 1/4" nut and ferrule
MATERIALS REQUIRED
• 35" long 2x4 for Anti-Tip support
• Copper water line tubing
• Water shut-off valve (optional but recommended)
• Custom panels for fresh food door, freezer drawer
and grille panel
• Screws to secure refrigerator to cabinetry.
• Stick-on hook and loop fastener strips
for 1/4" side panels
FLOORING
For proper installation, this refrigerator must be
placed on a level surface of hard material that is at
the same height as the rest of the flooring. This
surface should be strong enough to support a fully
loaded refrigerator, or approximately 700 ibs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under the
refrigerator where you are working.
GROUNDING THE REFRIGERATOR
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.
The power cord of this appliance is equipped with a
three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.
Have the wall outlet and circuit checked by a quali-
fied electrician to make sure the outlet is properly
grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong wall
outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
9
Page 10
Installation Instructions
[STEP 11REMOVE PACKAGING
CAUTION:Refi'igeratorismuch heavieratthe
top thanatthebottom -be carefulwhen moving.
When using a hand truck, handle from side only.
PRUDENCE:Le r0frig_rateur est beaucoup plus
lourd en haut qu'en bas. Ii faut 0tre prudent lots des
d0placements. Si un diable est utilis0, il faut soulever
le rOfrig0rateur sur le c6t0 seulement.
* Carefully cut banding at the top and bottom, remove
outer carton.
* Slide out back corner posts (2).
* Slide carton off top of cabinet.
NOTE: IT IS NOT NECESSARY TO LAYCABINET
DOWN IN ORDER TO REMOVE SKID!
* The unit is secured to the skid with 4 slotted tie-down
straps. Remove the four 5/16" bolts from the base
channels in the tie-downs.
• Remove the four 7/16"
bolts securing the straps
to the skid.
CAUTION:DO
NOT ATTEMPT TO
ROLL UNIT OFF SKID.
Remove
__ owns
ie 9 PRUDENCE:IL
NE FAUT PAS ESSAYER
DE FAIRE ROULER LE
RI_FRIGI_RATEUR POUR
L'ENLEVER DE LAY
PALETTE.
, Support blocks on the bottom of the refrigeration
case must be removed before sliding unit off skid or
damage will occm: Carefully, tilt refrigerator and
slide blocks out from beneath, slide unit off skid.
• Remove toekick. Set aside for final installation.
STEP 2] INSTALL WATER LINE
•A cold water supply is required for automatic ice-
maker operation. The water pressure must be be-
tween 40 and 120 p.s.i.
• Route 1/4" OD copper tubing between house cold
water line and the water connection location.
• Copper tubing should be long enough to extend to
the front of the refrigerator. Allow enough tubing to
accommodate bend leading into the water line
connection.
Shut off tile main water supply.
Turn on the nearest faucet long enough to clear the
line of waten
*Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
NOTE: It is best to install the valve into a vertical water
pipe. If you install the valve into a horizontal water
pipe, make the connection at the top or side, to
avoid drawing off any sediment from the water pipe.
. Drill a 1/4" hole in the water pipe.
*Fasten the shut-off valve to the pipe with pipe clamp.
. Tighten the clamp screws until the sealing washer
begins to swell. Do not over tighten.
. Place a compression nut and ferrule (sleeve) onto the
end of the tubing and connect it to the shut-off valve.
Make sure the tubing is fully inserted into the valve
and ferrule is tightened.
. Turn on the main water supply and flush debris. Run
about a quart of water through the tubing into a
bucket. Shut off water supply at the shut-off valve.
KCopper Tubin{
SaddleType
OutletValve
CompressionNut
\
Ferrule
(Sleeve)
NOTE: Saddle type shut-off valves are included in
many water supply kits. Before purchasing, make sure
a saddle type valve complies with your local plumbing
codes.
NOTE: Commonwealth of Massachusetts Plumbing ]
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consu t with your icensed p umber.
10
Page 11
Installation Instructions
[STEP 2A] WATER LINE
INSTALLATION WITH A REVERSE
OSMOSIS SYSTEM
Skip this step when not using an RO System
If the water supply to the refrigerator is from a
Reverse Osmosis Water System use the refrigerator's
filter bypass plug. Using the refrigerator's water
filtration cartridge with the RO filter can result in
hollow ice cubes.
I
FilterBypassPlug
I
[STEP 3_ INSTALL SIDE PANELS
Skip this step when not using side panels
If you are using 1/4" side panels, they should be
inserted into the case trim. Fasten the panels to the
refrigerator with stick-on hook and loop fastener
strips before setting refrigerator in place.
[STEP 41INSTALL ANTI-TIP
BRACKETS
WARNING:ANTI-TIPPRECAUTIONS
The refrigerator is top-heavy and must be secured to
prevent the possibility of tipping forward.
ATTENTION:PRECAUTIONS CONTRE LES
BASCULEMENTS
Le r_frig_rateur est beaucoup plus Iourd en haut et il
faut le maintenir en place pour Oviter la possibilitO de
son basculement vers l'avant.
• Cut a 2" x 4" x 35" block and secure the block to
the mounting brackets provided using #12 or #14
wood screws.
2x4Cut J
35"Length
Installation Mounting
Height Bracket
FromFloor
ScrewsMountedintoJ
VerticalWall Studs
• Secure the bracket with wood block to the back wall
so that it is 84" (or your installation height) from the
finished floor. Use #12 or #14 wood screws. See
illustration.
Brackets
Required
_1 NotRequired
Height
From
Floor
to
Bottom
ofWood
Block
SideView
• Screws must penetrate at least one inch into vertical
wall studs.
• Gently push refrigerator into the opening with
hands against front corners.
Important Note: Whenthe refrigeratoris installedundera soffit or if
thereis notenoughheightForthismethodof security,bracketscannot
beused,Proceedtostep5 to levelthe refrigeratorandthentostep 6to
securerefrigeratortocabinets,Therefrigeratormustbesecuredto
preventtipping,
11
Page 12
Installation Instructions
ISTEP 5] LEVEL REFRIGERATOR
All models have 4-point leveling. The front is sup-
ported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible from the front
of the refrigerator.
*To level the back of the refrigerator, turn the 7/16"
hex nut located above the front wheels. Turn
clockwise to raise or counterclockwise to lower the
refrigerator.
*For front leveling, use a 1-1/4" open-end wrench.
*Adjust height of refrigerator to match installation
cutout opening 83-1/2 to 84-1/2". The refrigerator
should be level and plumb with cabinetry.
ISTEP 6] SECURE REFRIGERATOR
TO CABINETRY
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
, Raise the grille panel to access case trim.
, Drill hole in trim and drive screw through the trim
into adjacent cabinet.
* Follow the same procedure on the opposite side.
/
DriveScrews
ThroughCaseTrimandInto
AdjacentCabinets
12
Page 13
Installation Instructions
[STEP 71ADJUST DOOR SWING
NOTE: This refrigerator has a 2-position door stop.
When space does not allow the door to swing open
fully to 130°,you may change the door swing to a 90 °
opening. Skip this step if door opening is satisfactory
for your installation situation.
* Lift the grille panel to access the wire cover trim.
. Remove screws on both sides of the wire cover trim
and lift off.
. Use pliers to unscrew door stop and reinstall into
the 90 ° position.
I I
_ zJ
Remove
WireCover
TrimScrews
PinLocationFor
90° PinLocation
asShipped
130° DoorSwing
*Reinstall the wire cover trim.
[STEP 8 1INSTALL GRILLE PANEL
, Raise the grill panel to stop position.
Looser_nf
Side m
Trim •
Screw
I
Raise÷4/
Grille/[ I
P_
_ jz
AdjustNutBelow
SpringtoAccommodate
PanelWeight
Loosen
Side
Trim
Screw
* Loose screws on side trim behind frame. Remove
bottom trim.
. Slide panel over the metal baker panel and into the
trim.
* If necessary, tap with a wood block until panel slips
under the top trim piece.
. Reassemble bottom trim. Tighten screws.
. Adjust the hinge spring to accommodate the panel
weight, if necessary.
13
Page 14
Installation Instructions
[STEP INSTALL FRAMED PANELS
Right hand models shown. Use the same instructions for
left hand models.
IF YOU ARE INSTALLING OVERLAY PANELS, GO
TO STEP 9A.
- UseFrontHoles
to SecureTrim
"_-_ JseRearHoles
to SecureHandle
Handle _- DoorTrim
Trim
Refrigerator
Door
Standardsuppliedhandleshown
in 1/4" panelposition,
Install door and drawer panels:
• Open door to 90 °. Remove the 4 Phillips head screws
from the door handle.
• Remove handle. Retain all screws.
• Remove 4 screws holding trim, lift off trim. Retain
SCFeWS.
• Slide framed panel into the door trim.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the FRONT screw holes.
• Secure the handle to the door using the REAR screw
holes.
• Follow the same procedures to install the drawer panel.
Custom handles
If you are using custom handles, the handle must be
properly secured to the panel before sliding the panel
into the trim.
• The cabinet manufacturer will supply the custom
handle and hardware.
• Secure the door/drawer trim using both the FRONT
and REAR screw holes. Discard supplied handle.
14
Page 15
Installation Instructions
ISTEP 9A] INSTALL OVERLAY PANELS Right hand modelsshown.Use the same instructionsfor
heft hand models.
UseFrontHoles
to SecureHandle
_ \Use RearHoles
to SecureTrim
Handle
Trim
Move
Forward
For3/4"
Panel
j DoorTrim
Refrigerator
Door
Suppliedhandleshowninthe
overlaypanelposition,
Install door and drawer panels:
• Open door to 90 °. Remove the 4 Phillips head screws
from the door handle.
• Remove handle. Retain all screws.
• Remove 4 screws holding trim, lift off trim. Retain
screws.
• Slide overlay panel into the door trim.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the REAR screw holes.
• Secure the handle to the door using the FRONT screw
holes.
• Follow the same procedures to install the drawer panel.
Custom handles
If you are using custom handles, the handle must be
properly secured to the panel before sliding the panel
into the trim.
• The cabinet manufacturer will supply the custom
handle and hardware.
• Secure the door/drawer trim using both the FRONT
and REAR screw holes. Discard supplied handle.
15
Page 16
Installation Instructions
ISTEP 101CONNECT WATER SUPPLY
Check to be sure that refrigerator power cord is not
plugged into the wall outlet.
\ House Refrigerator
_,_ater Supply
\ Water Supp_
• Locate and bring copper tubing to the front of the
cabinet.
• Turn the water on to flush debris from line. Run
about a quart of water through tubing into a bucket,
then shut-off water.
• Slip a 1/4" nut and ferrule (provided) over both
ends of the copper tubing. Insert tube into the
union fitting on the unit and tighten nut to union.
• Turn on the water to check for leaks.
Note: Make sure excess tubing length does not
interfere with drawer closing or toekick installation.
[STEP 111 CONNECT POWER
• Connect refrigerator power cord plug to a properly
grounded receptacle, accessible through the top
left side of the grille opening.
Electrical MasterEight
Outlet Switch
I
Raiae
Grille_1
Panel_'
• Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights
are on.
• The temperature controls are preset at 37°F for the
fresh food section and 0°F for the freezer.
• Allow 24 hours to stabilize before making
adjustments.
[STEP 12] START ICEMAKER
• Flip the switch to I (ON). The icemaker will begin
operation automatically.
• Be sure nothing interferes with the sweep of the
feeler arm.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to O (OFF).
ISTEP 13 ]INSTALL TOEKICK
• Locate the supplied toekick (shipped taped to
the side of the refrigerator). Install with 2 screws
provided, adjust to desired height and tighten screws.
• A custom toekick can be installed to match or
complement the surrounding cabinetry. Use the
supplied toekick as a template to cut out the notch
and vent holes.
SuppliedToekick
1/4"or ThickerToekick
Important: The vented toekick must remain unob-
structed for proper air circulation and refrigerator
operation.
16
Page 17
Notes
17
Page 18
Notes
18
Page 19
Notes
19
Page 20
Note: While performing installations described in this book,
safety glasses or goggles should be worn,
For Monogram _ local service in your area, call
1-800-444-1845,
Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
_49-60136-1 ]
[Dwg. No. 164D4371P001J
(ND429) 3/02
75260 01
Monogram2
Webring good things to life.
GeneralEle:'tricCompany
Louisville,KY40225
Loading...