Page 1
Installation
Instructions
Built-In Bottom-Freezer
Refrigerators
ZlC360NRH,ZlC360NLH,
ZlCS360NRH,ZlCS360NLH
DesignGuide
With InstallationInstructions
Monogram:_
Page 2
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT - heseinstructions
for h)cal inspector's use. Obserxe all goxerning codes
and ordinances.
• Note to Installer -- Be sure to leaxe these
instructions with the (:onsmner.
• Note to Consumer -- Kee I) these instructions
with your Owner s Manual for flmue reference.
WARNING:
This appliance must be properly grounded. See
"(;tom, cling tile Refrigerator," page 9.
AVERTISSEMENT
Cet appareil (hilt &tre correctement mis _'lla terre.
Consulter <_ Mise a la terre du rg_frig_ratem" _>,I)age, 9.
If you receixed a damaged refrigerator, you should
immediatelx contact xom" dealer or builder.
CAUTION:
Due to tile weight and size of this refrigerator, and
to reduce tile risk of personal ii_jur) or damage to
tile product--THREE PEOPI,E ARE REQUIRED
FOR PROPER ]NSTAI,I,ATION.
PRUDENCE
_ cause du poids et de la taille de ce r_frig&'ator et
pore" r&luire le risque de blessure et de dommages,
li, E&UT TROIS PERSONNES POUR EMILE
I,'INSTAI,LATION CORRECTEMENT.
Skill Level -- Installation of this refrigerator
requires basic mechanical, carpent_ T and plmnl)ing
skills. Proper installation is tile responsibility of tile
installer. Product tailure due to improper installation
is not covered trader tile GE Appliance Warranty.
See tile Owner's Manual fin" warranty inlm'mation.
WARNING:
• These refl'igerators are top-heavy and must
be secm'ed to prevent the possibili W of tipping
forward. Anti-Tip protection is required. See page
11 for details,
• Use this appliance only fin" its intended purl)ose.
• hmnediately repair or replace electric se_wice cords
that become fl'aved or damaged.
• /Jnl)lug tile refl'igerator heft)re cleaning or making
repairs.
• Repai_ should be made by a qualified service
technician.
AVERTISSEMENT
• Ces r_frig_rateurs sont lourds en haut et il taut les
arrimer pore" _\'iter leur basculement. 11 taut avoir
tm syst_)me de protection contre le renversement.
Voir les d_tails page 11.
• 11 ne faut utiliser cet appareil que pour l'utilisation
aI)I)ropri_e.
• R_parer ou remplacer imm&liatement tout cordon
_lectrique efliloch_ ou endommag_,
• 11 taut d_brancher le r_flJg_rateur awmt le
nettoyage ou route intervention.
• i,es r_parations doivent _tre taites par tm
technicien qualifi_,
For Monogrmn local service in your area, call
1.800.444.1845.
For Monogrmn service in Canada, call
1.888.880.3030
For Monogrmn Parts and Accessories, call
1.800.626.2002.
www. monogram.corn
CONTENTS
PlanningGuide
The Installation Space ............................3
Dimensions and Clearances ..................3
130° Door Swing ......................................4
90° DoorSwing ........................................5
Customization Basics ..............................6
Panel Dimensions....................................7
Side Panels................................................8
ZU62 Grille PanelDimensions ..............8
InstallationInstructions
Tools,Hardware, Materials ....................9
6rounding the Refrigerator ....................9
Step 1, RemovePackaging ..................10
Step 2, Install Water Line......................10
Step 2A, R0 Water Line ........................11
Step3, Install Side Panels....................11
Step4, Install Anti-Tip Brackets ..........11
Step 5, Level Refrigerator ....................12
Step6, Alternate Anti-Tip Procedure..12
Step7, Secure Refrigeratorto
Cabinetry....................................12
2
Step 8, Adjust Door Swing....................13
Step 9, Install Grille Panel ....................13
Step 10, Install Framed Panels ............14
Step 10A, Install Overlay Panels..........15
Step 11, ConnectWater Supply ..........16
Step 12, ConnectPower ........................16
Step 13,Start Icemaker ........................16
Step 14, Install Toekick..........................17
Page 3
Design Guide
THE INSTALLATION SPACE
35-I/2"
Finished Width
.to.t,,,i lth 2-8/16''
mustbe /11 _T .
. 5,j2- / Im :8
The 1inished _1_ Wal,View
maxL10
84-1/ ]] 75" From
83-1/2" min of Electrical Area
Finished ]L_24" Cutout Depth ]] Floor to Bottom
Opening I ] E
I 115' Water Supply _
| ])'0 _:: (_
_' 31/2" 31/2" '
Water And Electrical Locations
Electrical and water suppl) must be located as shown.
The cutout depth must be 24"
Tile refrigerator will project forward, slighfl} bexond
ac!iacent cabinetry, dei)ending, on _our installafilm.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
• A l 15 volt 60Hz., 15 or 20 amp power supply is
required. An indMdual properly grotmded branch
circuit or circuit breaker is recommended. Install
a properly gromMed B-prong electrical receptacle
recessed into tile back wall. Electrical must be
located on rear wall as shown.
Note: GFI (grotmd tault interrupter) is not
i'ecoi/llllended.
• _&'_ter line can enter the opening through the
floor or back wall. Route GE SmartConnect'" kit or
]/4" O.D. copper tubing between the cold water
line and tile water connection location. Tile tubing
should be long enough to extend to tile fl'ont of the
refl'igerator. Installation of an easily accessible
sh m-off wflve in the water line is required.
DIMENSIONS AND CLEARANCES
35" 25-3/8" FramedModels
CaseWidth 25-3/4" StainlessSteelModels
__ CaseDepth
]_z_____ _ Shipping height. The
_83-12"] Floorto height. Note that the top
at II TopFrame case trim at the front is
Re__1/_ 1/2" higher and will overlap
DepthIncludingHandles:
26-7/8" FramedModels
274/4" StainlessSteelModels
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set ] 30 ° door swing can be
ac!justed to 90 ° if clearance to a(!jacent cabinets or
walls is restricted.
130° Door Swing
130° ,
Allow 25" minimmn clearance for a flfll
130 ° door swing. Allow 15" fl_r pan remoxal.
4" minimum clearance is required when door swing
is a(!justed to 90 °. If the 90 ° door stop position is
used, pan access is maintained, but pan remowfl is
restricted.
See illustrations pages 4 and 5 to detemfine door swing
interaction with a(!iacent cabinets or cotmtertops.
_84"From 83-1/2" min. to 84-1/2" max.
" meto
FrameWidth
Minimum
to Wall
, 25"_
i
[,,,
to fit into a cutout that is
refrigerator can be adjusted
Use leveling legs and wheels
upper cabinetry or soffit.
for a maximum 1" height
adjustment.
90° Door Swing
,
L_ 'l
(
90° :j
] Behind
]Frame
!36-3/4"
4" Minimum
to Wall
ZUG2, ZUGSS2 Unified Grille Panel Kit
• If you are installing two refl'igerators, side b_,side,
the installation space must be 71-1/2" wide.
Note:Additional cutout width may be required when side panels
are used. Addside panelthickness to the finished cutout to
calculate rough-in width.
• The water and electrical locations fl)r each product
must be located as shown.
• A separate l I5V, 60Hz., 15 or 20 amp power supply
is recommended fin" each product.
-_71-1/2"FinishedWidth--
WallView
_}6" ; F6"
10" 10"
84-1/2"max
83-1/2"rain
Finished
Opening
.............................
24"Cutout
Depttl
_-/ 26"_ _26 "_
3-1/2"
75"From
FloortoBottom
of ElectricalArea
WaterSupply_5
3-1/2"
3
Page 4
Refrigerator
Design Guide
FramelessCabinets:The casetrim
overlaps cabinets atthe top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interference with
23-7/8"From
Rearof
Refrigerator
cabinet door swing. The opening must
allow for filler strips.
Case
Trim
1/4"
1/2"
3/4"
2_1/2 I'
2-1/4"
3/4" Overlay
Panel
(NominalSize)
Top View
130 ° DOOR SWING
(factory setting)
Scale 1:1
Door
4
Page 5
Refrigerator
Design Guide
_Case Trim
FramelessCabinets:The
case trim overlaps cabinets
atthe top and sides.
Therefore, frameless
cabinets may require filler
strips to prevent interference
with cabinet door swing. The
opening must allow for filler
strips.
23-7/8"
FromRearof
Refrkerator
Door
i
i
i
i
, ,]
i i
1/2"
i
1-1/2"
3/4" Overlay
Panel
(NominalSize)
Top View
90 ° DOOR SWING
(optional setting)
Scale 1:1
i I 1-1/4"
I I
I I
5
Page 6
Design Guide
CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits
Models Available
Stainless Steel Wrapped Models:
ZICS360N RH (right-handed door)
ZICS360N I,H (left-handed door)
Trimmed models:
ZICS60N RH (fight-handed door)
ZIC360N I,H (lett-handed door)
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refi'igerators have wrapped
doors and grille panel, beveled edges, and tubular
stainless steel handles that coordinate with other
Monogram appliances. These models are shii)ped
ready fl)r installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized
with decorative panels. Field installed custom door
and grille panels are required.
Framed panels
You may install I/4" thick custom panels Ii'om yore"
cabinet manufhcturer. The decorative panel slides
into the factory installed trim. Or, order black,
white and stainless steel accesso_ T panels fl'om your
Monogram deale_:
Overlay panels
You may also choose to install custom overlay panels
from vom" cabinet manufhctm'er. This design provides
a seamless appearance which integrates smoothly with
SmTom_ding cabinetry.
Standard supplied handles shown in 3/4"overlay panel position.
Door and Drawer Handles
The standard supplied handles can be a(!iusted t(>
accommodate both framed or overlay panels. Custom
handles of yore" choice, SUl_plied by yore" cabinet maker
can also be installed on overlay panels. If desired, you
may order ZKHCSS2 Monogram stainless steel tubular
handle kit for 3/4" overlay panels.
J
StandardDoorHandle FramedPanel
Standard supplied handles shown in 1/4"panel position.
Optional Accessory Kits
• ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels. This kit also
includes a handle side trim for custom handles.
• ZUG2: For side-by-side installation of two trimmed
bottom-ti'eezer refrigerators. This kit provides fl)r the
installation of a tmified custom grille panel to span the
width of two milts using a framed or overlay panel.
• ZUGSS2: For side-by-side installation of two stainless
steel wrapped bottom-ti'eezer refrigerators. This kit
provides a ratified stainless steel grille panel to span
the width of two milts.
Side Panels
Side panels must be used whenever the sides of the
refl'igerator will be exposed.
Accessory Panels
White, black and stainless steel accessory panels are
available fl'om your Monogram dealer. Panels are cut
to size and ready to install.
ZPBC360-Black, ZPWC360-_.Vhite,
ZPSC360-Stainless Steel Panels
6
Page 7
Design Guide
1/4" FRAMED PANEL DIMENSIONS
If you choose to install fl'amed panels, thex must be
cut to the dimensions shown. The panels will slide
into the fl'ame on the door, drawer and grille.
If the custom panel is less than 1/4" thick and if it
fits loosely in tile door fl'ame, it can be backed up
with a piece of filler material or foam tape to
improve the fit.
[ Grille Panel ]_
FramedPanel Dimensions
1/4"FramedPanel 33-7/8" 8-7/8" 46-1/16" 21-7/8"
Panel
FreshFood l--
OverlayPanel Dimensions
1/4"Backer Panel 33-7/8" 8-7/8" 46-1/16" 21-7/8"
Freezer Drawer D
Panel
0.10"Spacer Panel 32-1/2" 7-5/8" 44-11/16" 20-1/2"
3/4"Overlay Panel 34-1/8" 9" 46-5/16" 22"
Door
] Reveal
IMPORTANTNOTE:Maximum total panel
weight:
• Freshfood door panel-58 Ibs.
• Freezer drawer panel- 28 Ibs.
• Grille Panel- 11 Ibs.
A (Width) B (Grille Height) C(FFHeight) D (FZHeight)
A (Width) B (Grille Height) C(FFHeight) D (FZHeight)
3/4" OVERLAY PANEL DIMENSIONS
For a illoi'e CtlStOlll al)l)eaFallce , overlay panels illaV be
installed on trimmed models. The overlay panel must
be secm'ed to a 1/4" thick backer panel which slides
into the trim. A spacer panel 0.10" thick must be
placed between the overlay and backer panel.
Assemble the panels with glue and screws.
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with ghle.
• Center the spacer and backer panel on tile overlay
panel and secure with glue and screws. Screws must
be cotmtersunk into the backer panel.
Door/Drawer
\
\\
\
1/4"
Backer,. .
Panel _ _Spacer
IMPORTANTNOTE:Maximum
total weight for the assembled
panels:
• Freshfood door panel-58 Ibs.
• Freezerdrawer panel- 28 Ibs.
• Grille Panel- 11Ibs.
NOTE: I,eft-to-right offset is not alwa)s equal to
tol)-to-bottom offset,
Page 8
Design Guide
SIDE PANELS
Side panels must be used whenever the sides of the
refligerator will be exposed. The l/4" side panels
will slip into the side case trim. Secure the panels to
the refiigerator with stick-on hook and loop tastener
strips. Order the side panels fl'om the cabinet
IIla n II[;l ct HI'eF,
• Cut a notch in the top t]'ont corner as shown to
allow clearance fin" corner keys in the fl'ont side
trim,
* Dei)ending. on
installation height.
_84"
ZUG2 GRILLE PANEL DIMENSIONS
The ZL (,2 tmified grille panel kit provides tot the
installation of a framed or oxerla) grille panel.
A
[ GrillePanel ]_
FramedPanel Dimensions
A (Width) B (Height)
1/4"Framed Panel 69-7/8" 8-7/8"
OverlayPanel Dimensions
A (Width) B (Height)
1/4"Backer Panel 69-7/8" 8-7/8"
0.10"Spacer Panel 68-1/2" 7-5/8"
3/4"Overlay Panel 70-1/8" 9"
i i
i i i
Assemble the oxerla)panels in the same manner as
the door and drawer panels.
8
Page 9
Installation Instructions
TOOLS REQUIRED
• Tinsnips to cut banding
• Stepladder
• Bucket
• i,evel
• Appliance Hand T) uck
• Tubing cutter
• 7/16" open-end wrench
• #2 Phillips screwdriver
• Drill and ai)propriate bits
• 5/16", 7/16" socket
• Satety glasses
• 1-1/4" open end wrench
• Plie_
• 1/4" ratchet
HARDWARE SUPPLIED
• X*Vaterfilter byl)ass plug
• Anti-Tip brackets
• 1/4" nut and teHule
MATERIALS REQUIRED
• 35" long 2x4 for Anti-Tip support
• 1/4" COl)per water line tubing or GE
SmartConnecg" Refrigerator Tubing kits
• Water sh ut-ofl wdve
• C/IStOIll panels tor fl'esh tood door, fl'eezer drawer
and grille panel
• Screws to secm'e refrigerator to cabinetry:
• Stick-on hook and loop fastener strips for
1/4" side panels
FLOORING
For proper installation, this refl'igerator must be
placed on a level sm'lace of hard material that is at
the same height as the rest of the flooring. This
surface should be strong enough to support a fldlv
loaded refrigerator, or approximately 1,200 lbs.
NOTE: Protect the finish of tile flooring. (_ut a large
section of the cardboard carton and place trader the
refl'igerator where you are working.
GROUNDING THE REFRIGERATOR
IMPORTANT--(Please read carefully)
FOIl PERSONAl, SAFETY, THIS APPIJANCE MUST
BE PROPERI,Y GROUNDED.
Tile power cord of this appliance is equipped with
a 3-prong (grounding) plug which nlates with a
standard three-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
fl'om this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grolmded.
Where a standard 2-prong wall outlet is enco/mtered,
it is yore" personal responsibility and obligation to
have it replaced with a properly gro/mded S-prong
wall outlet.
DO NOT, UNDER ANY _-'_I_
CIRCUMSTANCES, CUT
OR P.EMOVE THE THIRD
(GROUND) PRONG FROM
THE POWER CORD.
DO NOT USE AN ADAPTER PI,UG TO CONNECT
THE I/EFRIGERATOR TO A 2-PRONG OUTI,ET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPIJANCE.
9
Page 10
Installation Instructions
[STEP 1] REMOVE PACKAGING
CAUTION:Relrigerator is much hea, ier at the
top than at the botton/ - be careflfl when moxing.
X4hen usim* a hand track, handle fl'om side onE.
PRUDENCE: est pl.s
hmrd en haut qu'en bas. I1 taut 6tre prudent lots des
d@lacements. Si un diable est utilis& il taut soulexer le
r_frig&'ateur stu" le c6t_ seulement.
• Careflflly cut banding at the top and bottom,
relilove otKer carton.
• Slide out back corner posts (2).
• Slide carton ott top of cabinet.
NOTE: IT IS NOT NECESSARY TO I,AY CABINET
DOWN IN ORDER TO P,EMOVE SKID!
• The trait is secured to the skid with 4 slotted
tie-down straps. Remove the fimr 5/16" bolts fl'om
the base chmmels in the tie-downs.
[STEP 2] INSTALL WATER LINE
/ • Remoxe the four 7/16"
bolts secm'ing the straps
to the skid.
CAUTION:DONOT
ATTEMPT TO ROI,I,
UNIT OFF SKID.
Remove
Tie-D0wns
J
• Sui)port blocks on the bottom of the refligeration
case must be removed before the refl'igerator is
taken off the skid or damage will occm'. Careflfll>
tilt refligerator and slide blocks out fl'om beneath.
• Remove toekick. Set aside for final installation.
• I,itt the refrigerator off the skid with an appliance
dolly. Handle fl'om the sides.
PRUDENCE:ICNE
FAUT PAS ESSAYER DE
FAIRE ROUI,ER I,E
Rt_FI{I Gt_RATEUR POUR
I/ENI,EVER DE lAY
PA1,ETTE.
• A cold water SUl)ply is required fl_r automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i.
• Route l/4" OD COl)per or GE Smart(:onnect '_
plastic tubing between house cold water line and
the water connection location.
• Tubing should be hmg enough to extend to the
fl'ont of the refl'igeratm: Allow enough tubing to
accommodate bend leading into the water line
connection.
NOTE: The only GE approved plastic tubing is
sui)plied in the GE Smart(:onnect '_ Refl'igerator
Tubing kits. Do not use any other plastic water sui)ply
line because the line is trader pressure at all times.
Other types of plastic may crack or Hq)ttu'e with age
and catlse water dalllage to voui" hollle.
GE Smart(]onnect ''_Refl'igerator Tubing FAts are
available in the following lengths:
2' (.6 m) WX08X10002
6' (1.8 m) WX08X10006
15' (4.6m) WX08X10015
25' (7.6 m) _,\_X08X10025
Shut off the main water supply,
Turn on the nearest faucet long enough to clear the
line of water.
• Install a shut-off \_d\'e between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off \Mve should be located where it will be
easily accessible,
*'WaterlineTubing
• Turn on the main water supi)ly and flush debris.
Rm_ about a quart of water through the robing into
a bucket. Shut off water sui)i)ly at the shut-off \:five.
NOTE: Saddle b'pe shut-ofl'wdves are included in
inany water supl)ly kits. Before i)urchasing, inake sure a
saddle type valve complies with your local I)lumbing
codes.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248(:MR shall be adhered to. Saddle \;flves are
illegal and use is not pemfitted in Massachusetts.
Consult with yore" licensed plumbe_:
10
Page 11
Installation Instructions
ISTEP 2AI WATER LINEINSTALLATION
WITH A REVERSEOSMOSIS SYSTEM
Skip thisstepwhen not usingan ROSystem
If the water supply to the refl-igerator is fl'om a Reve_e
Osmosis Water System use the reliigerator's filter bypass
plug. Using the refi-igerator's water filtration cartridge
with the RO filmr can result in hollow ice cubes.
\
FilterBypassPlug
ISTEP31INSTALLSIDEPANELS
Skip this step when not using side panels
If _)u :u'e using l/4" side panels, tbe v should be inserted
into the case trim. l:asmn the panels to the refiigerator
with stick-on hook and loop fi_stener strips before setting
retiigemtor in place.
I STEP 41 INSTALLANTI-TIP BRACKETS
WARNING:ANTI-TIP PRECAUTIONS
The refiJger_Jtor is top-hear?' _md must be secured to prexent
the possibility of tipping fiwward.
ATrENTION:PRECAUTIONS CONTRE LES
BASCULEMENTS
Le r_tiig_ntteur est beuucoup phts lourd en haut et il timt le
maintenir en place pour &iter la po,_sibilit_ de son basculerrlent
xers l'axant.
• Cut a 2" x 4" x 35" block md secule the block to the
motmtii_g, brackets t)r°xided using,, #1,_)or #14 wood ....screws
2x4But _€
35"Length
Installation Mounting
Height Bracket
FromFloor
ScrewsMountedintoj
VerticalWall Studs
• Secure the bracket sqtb wood block to the back s_ull so that it
is 84" (or }our installation height) from the finished floox:
[}se #12 or #14 wood scre'_s. See illustn_tion.
Brackets
Required
Block.
-- NotRequired
__ Beneatha
Height Soffit
From
Floor
to
Bottom
ofWood
Block
Brackets
SideView
• ScI'ex_sn/ust penetrate at least one inch into _ertical wall
studs.
• Beiore pushing the reJiigerator into the opening, plug
the po_vr cord into the receptacle. Open the grille panel
and x>ach into the opening at the back to grasp the power
cord. Pull the pox_r cord into the opening as you push the
refligemtor back.
• (;en@ push reliigemtor into the opening with hands ag_dnst
_I'OI/t COFI/eFS.
hnportantNote:Whentherefrigeratorisinstalledunderasoffitorifthereisnot
enoughheightforthismethodof security,bracketscannotbeused.Proceedtostep5
toleveltherefrigeratorandthentostep6tosecurerefrigeratortocabinets.The
refrigeratormustbesecuredtopreventtipping.
11
Page 12
Installation Instructions
[STEP 5] LEVEL REFRIGERATOR
All models have 4-point leveling. The fl'ont is
supported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible fl'om the fl'ont
of the refl'igerator.
• To level the back of the refl'igerator, turn the
7/16" hex nut located above the fl'ont wheels. Turn
clockwise to raise or counterclockwise to lower the
refl'igera toi;
• For fl'ont leveling, use a 1-1/4" oi)en-end wrench.
• A(!just height of refl'igerator to match installation
cutout opening 83-1/2 to 84-1/2". The refl'igerator
should be level and plumb with cabinetry.
]STEP 6] ALTERNATE ANTI-TIP
PROCEDURE
The refrigerator must be secured to prevent tipping.
The aalti-tip brackets cammt be used on metal wall
studs. Use this Alternate Procedure to secure the
refrigerator against tip-over whenever metal wall studs
are encountered and there is no soffit.
SideView
TopCaseTrim
InstallFour
1-1/2"DrywallScrews
ThroughTrimand IntoSoffit
or3/4" Min.WoodBrace
CAUTION:
The rear leveling wheels and fl'ont leveling legs are
limited to a maximum height a_!justment of l ". If the
installation requires more than 84-1/2" height, the
installer should elew_te the refrigerator on a sheet of
pl)_vood or runnei_. Cabineti T trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator
more thm_ 1", you will damage the front leveling legs
mad the rear leveling wheels.
PRUDENCE
i.es roues de nivellement arri&re et les pattes de
nivellement avant permettent un r_glage maximal
de 25 mm (l po). Si l'ouverture pour le r_fl'ig&'ateur
a une hauteur SUl)_riem'e _'l 2,15 m (84-1/2 po),
l'installateur doit _lever le r_fl'ig_rateur sur une
teuille de contre-plaqu_ ou des glissi&res. 11 est
_galement possible d'ajouter des baguettes de
finition des placards sur le haut de l'ouverture afin
de la r_duire. I.ever le r_fl'ig&'ateur de plus de
95 mm (l po) endommage les pattes de nivellement
avant et les roues de nivellement arri&re.
• Raise the grille panel to access case trim.
• Use a 3/16" bit to drill fimr evenly spaced clearance
holes through the metal top case trim.
• Use a 1/16" bit to drill to pilot holes through the
metal clearance holes and into the wood soffit. The
holes should be centered in the soltit or a 3/4" rain.
wood brace. The brace spanning the enclosure must
be securely tastened to cabinets on both sides.
• Install four, 1-1/2" drywall screws into the pilot holes.
[STEP 7] SECURE REFRIGERATOR
TO CABINETRY
X'_henexer possible, perfom_ this step for anti-tip
security or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Raise the grille panel to access case trim.
• Drill hole in trim and drive screw through the trim
into ac!jacent cabinet.
• Follow the same procedure on the opposite side.
A
12
DriveScrews
ThroughCaseTrimand Into
AdjacentCabinets
Page 13
Installation Instructions
]STEP 81 ADJUST DOOR SWING
NOTE: This refiigerator has a 2-position door stop.
When space does not allow the door to swing open
fldlv to 130 °, you may change tile door swing to a 90 °
opening. Skip this step if door opening is satisfactory
for your installation situation.
• i,ift the grille panel to access the wire cover trim.
• Remove screws on both sides of tile wire cover trim
and lift off.
• Use pliers to tmscrew door stop and reinstall into
tile 90 ° position.
I
Remove
Wire Cover
TrimScrews
9PinLocationFor
0° Door_ PinLocation
130° DoorSwing
<L..
[STEP 91 INSTALL GRILLE PANEL
• Raise tile grill panel to stop position.
I
Loosen
Side
Trim _,
Screw
W
• i,oose screws on side trim behind fl'ame. Remove
bottom trim.
• Slide panel over the metal baker panel and into the
trim.
• If necessary, mp with a wood block tmtil panel slips
trader the top trim piece.
• Reassemble bottom trim. Tighten screws.
• A(!just tile hinge spring to accommodate tile panel
weight, if necessary.
__ P_
AdjustNutBelow
Springto Accommodate
PanelWeight
Grille]|_
I
Loosen
Side
Trim
Screw
• Reinstall tile wire cover trim.
asShipped
13
Page 14
Installation Instructions
[STEP 10] INSTALL 1/4" FRAMED
PANELS
Handle
Trim
UseFrontHoles
to SecureTrim
UseRearHoles
to SecureHandle
Standardsuppliedhandleshown
Right hmad models shown. Use the same instructions
for left hand models.
IF YOU ARE INSTALLING OVERLAY PANELS,
GO TO STEP 9A.
j DoorTrim
Refrigerator
Door
in 1/4" panelposition.
Install door and drawer panels:
• Open door to 90 °. Remove the 4 Phillips head screws
fl'om the door handle.
• Remove handle. Retain all screws.
• Relnove 4 screws holding triln, lili off trim.
Retain screws.
• Slide fl'amed panel into the door trim.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the FRONT screw holes.
• Secure the handle to the door using the REAR screw
holes.
• Follow the same procedm'es to install the drawer panel.
14
Page 15
Installation Instructions
[STEP 10A] INSTALL OVERLAY
PANELS
Handle
Trim
- UseFrontHoles
to SecureHandle
UseRearHoles
to SecureTrim
Right hand models shown. Use the stone instructions
for left hand models.
DoorTrim
Refrigerator
Door
Move
Forward
For3/4"
Panel
Suppliedhandleshowninthe
overlaypanelposition.
Install door and drawer panels:
• Open door to 90 °. Remove the 4 Phillips head screws
ti'om the door handle.
• Remove handle. P,etain all screws.
• Remove 4 screws holding trim, lilt off trim.
Retain screws.
• Slide overlay panel into the door trim.
Custom handles
If you are using custom handles, the handle must be
properly secm'ed to the panel betore sliding the panel
into the trim,
• The cabinet manufacturer will SUl)ply the custom
handle and hardware.
• Secm'e the door/drawer trim using both the FRONT
and REAR screw holes. Discard SUl_plied handle.
• There are two sets of holes in the handle side trim.
Replace handle side trim by installing the original
screws in the REAR screw holes.
• Secure the handle to the door using the FRONT screw
holes.
• Follow the same procedures to install the drawer panel.
15
Page 16
Installation Instructions
[STEP 11 ]CONNECT WATER SUPPLY
L[
• i,ocate and bring tubing to the fl'ont of the cabinet.
• Turn the water oil to flush debris frmn line. Run
about a quart of water through tubing into a bucket,
then shut off wa te r.
Copper Tubing:
• Slip a 1/4" nut and tbHule (provided) over both
ends of the COl)per tubing. Insert tube into the
tmion fitting on the trait and tighten nut to union.
• Tm'n on the water to check fin" leaks.
GE SmartConnect'" Tubing:
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression
nut until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Tm'n on the water to check for leaks.
ISTEP 12] CONNECT POWER
• Check to be sm'e tile power cord is phlgged into
the receptacle.
Grille]1!
Raise"N
:L.
Electrical MasterLight
Outlet Switch
• Check to make sm'e power to refl'igerator is on by
opening refl'igerator door to see if interior lights
are Oil.
• The temperature controls are preset at 37°F
fin" the fl'esh food section and 0°F fin" the freezer.
• Allow 24 horn's to stabilize before making
a({j ustm ents.
4
Panel_]
lSTEP 131START ICEMAKER
PowerSwitch
o
i
Note: Make sure excess tubim*_ length does not
interfere with drawer closim* or toekick installation.
• Flip the switch to I (ON). The icemaker will begin
operation automatically.
• Be sm'e nothing interteres with the sweep of the
feeler arm.
• Discard the first fidl bucket of ice cubes.
• To tm'n the icemaker off, set the switch to O (OFF).
16
Page 17
Installation Instructions
ISTEP 141 INSTALL TOEKICK
• I,ocate the supplied toekick (shipped taped to
the side of the refl'igerator), Install with 2 screws
provided, a_!iust to desired height and tighten
screws,
• A custom toekick can be installed to match or
complement the surrom_ding cabinetry, Use the
supplied toekick as a template to cut out the notch
and vent holes,
SuppliedToekick
1/4" or Thicker Toekick
Importm_t: The xented toekick must remain
m_obstructed fi)r proper air circulation and
refl'igerator operation,
17
Page 18
Notes
18
Page 19
Notes
19
Page 20
NOTE:While performing installations described in this book,
safety glasses or goggles should be worn.
t'_)r Mo_wg'ram _'_local ,_r_,ic_, ht your _m'a, c_lfl
l. 800.444. 1845.
)
NOTE: t roduct improvement is a continuing endeavor
al (;_ neral Electric. Th_ refm-_, malerials, aF,F,_aranc_
and sp,ucificalions are Stll._jec[tO change wilhotlr notice.
Pub.No.49-60320 ]
PartNo.197D6003PO01
16011-00 03-04JR
Printedinthe UnitedStates
J
Monogram:
GEConsumer & Industrial
Louisville, KY40225
@20046E Company
Loading...