GE ZIC360NR User Manual

ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator

R

6"

Wall View

Electrical

Area

84-1/2" max
83-1/2" min

Finished

Opening

75" From

Floor to

Bottom

of Electrical

Area

10"

5"

3 1/2"

5"

3 1/2"

Water Supply

24" Cutout Depth

35-1/2"

Finished Width

2-5/16"

25"

Min. to

Wall

130

°

130° Door Swing

23-7/8"
Behind
Frame

36-3/4"

90°

90° Door Swing

4" Min.
to Wall

2-5/16"

75" From

Floor to Bottom

of Electrical

Area

84-1/2" max
83-1/2" min

Finished
Opening

71-1/2" Finished Width

Electrical

5"

3-1/2"

24" Cutout
Depth

Water Supply

Wall View

24-3/16"

26"

6"

10"

10"

Water Supply

26"

5"

3-1/2"

*84" From
Floor to
Top Frame

35"

Case Width

*83-1/2"

at

Rear

Case Depth:
25-3/8" Framed Models
25-3/4" Stainless Steel Models

Depth Including Handles:
26-7/8" Framed Models
27-3/4" Stainless Steel Models

36"
Frame to Frame Width

with Automatic Icemaker

The Installation Space

The finished cutout width must be 35-1/2".

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond adjacent cabinetry,
depending on your installation.

The cutout depth beneath a soffit

When installed beneath a soffit, the soffit cannot exceed the 24"
installation depth shown. The top case trim overlaps the bottom
of the soffit.

Electrical

A 115V, 60Hz., 15 or 20 amp power supply is required.

An individual
properly grounded branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.
Water Line

All models are equipped with an automatic icemaker. The water line can
enter the opening through the floor or back wall. Route GE SmartConnect
Kit or 1/4" O.D. copper tubing between the cold water line and the water
connection location at the front of the refrigerator. The installation of an
easily accessible shut-off valve in the water line is required.

Product Dimensions

Door Swing Clearances

The installation must allow for clearances to adjacent walls or cabinets.
These refrigerators are equipped with a 2-position door stop. The
factory-set 130° door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.

Allow 25" minimum clearances for a full 130° door swing. Allow 15"
for pan removal.

• 4" minimum clearance is required when the door swing is adjusted to
90°. If the 90° door stop position is used, pan access is maintained,
but pan removal is restricted.

• See door swing illustrations to determine interaction with adjacent
cabinets or countertops.

ZUG2, ZUGSS2 Unified Grille Panel Kit

• If you are installing two refrigerators side by side, the installation space
must be 71-1/2" wide.

Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout to calculate
rough-in width.

™

• The water and electrical locations for each product must be located
as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for
each product.

Specification Created 5/04

110100

* Shipping Height. The

refrigerator can be
adjusted to fit into a
cutout that is 83-1/2" min.
to 84-1/2" max. height.
The top case trim at the
front is 1/2" higher and
will overlap upper
cabinetr y or soffit.
Use leveling legs and
wheels for a maximum
1" height adjustment.

Listed by
Underwriters
Laboratories

For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center

®

service, 800.626.2000.

ZIC360NR – GE Monogram 36" Built-In Bottom Freezer Refrigerator

Standard Door Handle

Framed Panel

Standard
Door Handle

3/4" Overlay Panel

1/4" Thick Backer Panel

.10" Thick Spacer Panel

R

with Automatic Icemaker

Customization Basics: Framed or Overlay Panels,
Custom Handles and Accessory Kits

These bottom-freezer refrigerators are factory set for a left or right
door swing. The door swing is NOT reversible. Choose an RH model
with hinge on the right side; the door swings left to right. Choose an
LH model with hinge on the left side; the door will swing right to left.

Right-Hand

Door Swing

Trimmed Refrigerators
ZIC360NRLH, ZIC360NRRH

Trimmed refrigerators are designed to be customized with decorative
panels. Field-installed custom door and grille panels are required.

Framed Panels

You may install 1/4"-thick custom panels from your cabinet
manufacturer. The decorative panel or accessory panel slides
into the factory-installed trim.

Standard supplied handles shown in 1/4" panel position.

Overlay Panels

You may also choose to install custom overlay panels from your cabinet
manufacturer. This design provides a seamless appearance which
integrates smoothly with surrounding cabinetry.

Left-Hand

Door Swing

Door Handles

The supplied handles can be adjusted to accommodate both framed
or overlay panels. Custom handles of your choice, supplied by your
cabinetmaker, can also be installed. If desired, you may order ZKHCSS2
Monogram

Side Panels

Side panels must be used whenever the sides of the refrigerator will
be exposed.

Optional Accessory Kits

ZKHCSS2: Monogram Stainless Steel Tubular Handle Kit and Handle
Side Trim for custom handles. For use on 3/4" custom panels.

ZUG2: For side-by-side installation of two trimmed bottom-freezer
refrigerators. This kit provides for the installation of a unified custom
grille panel to span the width of two units using a framed or overlay panel.

ZUGSS2: For side-by-side installation of two stainless steel-wrapped
bottom-freezer refrigerators. This kit provides a unified stainless steel
grille panel to span the width of two units.

Accessory Panels

White or black acrylic and stainless steel accessory panels are available
from your Monogram supplier. Panels are cut to size and ready to install.
These panel kits must be ordered separately.

Black White Stainless Steel

ZPBC360 ZPWC360 ZPSC360

®

Stainless Steel Tubular Handle Kit for overlay panels.

Standard supplied handles shown in 3/4" overlay panel position.

Specification Created 5/04

110100

Listed by
Underwriters
Laboratories

For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center

®

service, 800.626.2000.