GE ZIBS240PSS User Manual
ZIBI240PII – GE Monogram Bar Refrigerator with Icemaker Module
R
16" Minimum
110˚
Wall
24"
Cabinet
14" Minimum
110˚
Wall
24"
Cabinet
34-1/2"
to
35"
24" Min.
23-3/4"
34-1/2"
23-3/4" Stainless Steel
Models
24-7/8" Framed Models
1-1/2"
1/2"
Locate Outlet
Water and
Electrical
Locations
9"
Max.
10-1/2"
Depth Including
Handle:
26" Stainless Steel
Models Only
23-3/4" Min.
Note: If installing between frameless
cabinets, a 1/2" wide filler strip or side panel
may be required. The filler strip will act as a
spacer between the door case and adjacent cabinet
and will prevent interference with cabinet door swing.
The width of the opening must include filler panels.
(Custom panel required)
ZIBS240PSS – GE Monogram Bar Refrigerator with Icemaker Module
(Stainless steel)
Dimensions and Specifications (in inches)
Installation Space
The cutout depth must be 24"
The cutout dimensions shown allow for a full door swing and
access to the pull-out racks when installed as a built-in.
• The Bar Refrigerator with Icemaker can be free-standing.
• The stainless steel model ZIBS240PSS can be installed flush
with standard cabinetry. ZIBI240PII with custom panel will
project forward 1-3/4" of adjacent 24" deep base cabinets.
• A water line must be installed for icemaker operation.
Additional Specifications :
• A 120 volt 60Hz., 15 or 20 amp power supply is required. An
individual property grounded branch circuit or circuit breaker is
recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall as shown. Electrical
must be located on rear wall as shown.
interrupter) is not recommended.
Specification Created 3/04
120034
Note: GFI (ground fault
Product Clearances
Models with a Custom
Door Panel
Stainless Steel
Models
All models are factory set for a 110° door swing.
For a minimum 90° door swing:
• Allow 4" min. clearance to wall on the hinge side for Stainless
Steel models.
• Allow 4-1/2" min. clearance to wall on the hinge side for models
with a custom panel and custom handle
.
For a full 110° door swing:
• Allow 14" min. clearance to wall on the hinge side for Stainless
Steel models.
• Allow 16" min. clearance to wall on the hinge side for models with
a custom panel and custom handle.
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
®
appliance questions, visit our website at
GE
GEAppliances.com or call GE Answer Center
service, 800.626.2000.
®
ZIBI240PII – GE Monogram Bar Refrigerator with Icemaker Module
34-1/2" - 35"
24" Min.
47-1/2" Min.
1-1/2"
Locate Outlets
9"
Max.
10-1/2"
1-1/2"
9"
Max.
10-1/2"
24"
Overlay
Panel
1/4"
Backer
Panel
Door
.10 Inch
Spacer
Spacer Panel
Backer Panel
Overlay Panel
R
A
B
3/4" Deep
7/8" Wide
3/8" toward
the front side
Back Side
of Panel
(Custom panel required)
ZIBS240PSS – GE Monogram Bar Refrigerator with Icemaker Module
(Stainless steel)
Dimensions and Specifications (in inches)
For a complete food storage center, install two Monogram refrigeration
modules side-by-side.
Note: Reversible door swing on wine chillers/reserves and beverage
centers only. See below for combination cutout dimensions.
Important Note: Products must operate from separate, properly
grounded receptacles.
Note: Additional cutout width may be required for models with
custom panels.
Grounding the Bar Refrigerator with Icemaker
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
The power cord of this appliance is equipped with a 3-prong
(grounding) plug which mates with a standard 3-prong (grounding)
wall receptacle to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to
make sure the outlet is properly grounded.
When a standard 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced with a
properly grounded 3-prong wall out.
3/4” Overlay Panel Dimensions
Model ZIBI240PII requires customer-provided
overlay door panel.
• The overlay panel must be secured to a 1/4"
thick backer panel which slides into the trim.
A .10" thick spacer panel must be placed
between the custom and backer panel.
• A custom handle, supplied by your cabinet
maker, must be installed on the overlay panels.
Use a 3/4" router bit to cut a notch into the back side
of the assembled panel to allow for hinge clearance.
3/4" Overlay Panel Dimensions (in inches)
A (Width) B (Height)
1/4" Backer 23-3/16" 29-9/16"
0.10" Spacer 22-1/2" 29-1/16"
3/4" Overlay 23-5/8" 30"
NOTE: Max. assembled drawer panel weight
is 25 lbs.
Assemble overlay panels with glue
and screws.
• Center spacer panel on the backer panel,
left to right and top to bottom. Secure
the panels with glue.
• Center the spacer/backer panel on
the overlay panel. Secure with glue
and screws. Countersink screws into
the backer panel.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.
Specification Created 3/04
120034
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
®
appliance questions, visit our website at
GE
GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
Loading...