GE ZIBS240PBSS Owner's Manual

Download

Page 1

Owner's

Manual

Bar Refrigerator

with Icemaker

ZIBI240 ZIBS240

Monogram:

Page 2

Consumer Inffwmation

Bar Re,/*'ig'e*'ator, with Icemaker

Introduction

Contents

Be/bre

using your bar

r@ig_ator

with ieemaher

Your new Monogram bar refligerator with icemaker makes an eloquent statement of

style, convenience and kitchen planning flexibility. Whether yon chose it if)i its purity of design or the assiduous attention m detail, you will find that wmr Monogram bar refrigerator with icemaker's superior blend of ffwm and flmction will delight you ff)r years to come.

The in%rmation on the %llowing pages will help you operate and maintain your bar refligerator with icemaker properly'.

If you have any other questions, _isit our _¢\_bsite at: ge.com

Built-In Dimensions ............. 1,3, 14

Care and Cleaning .............. 11, 12

Consumer Serxices ................ 19

Controls and Features ............ 8-10

Installation Instructions .......... 14, 15

Model and Serial Numbers ........... 2

Read this manual carefldlv. It is intended to help you operate and maintain your

new bar refrigerator with icemaker properly'.

Keep it handy' %r answers to your questions.

Problem Solver ................. 16-18

Product Registration ................ 2

Repair Seiwice .................. 3, 19

Safety Instructions ................ 4-7

V\]uran ty' ................. Back Cover

Ifvon don t undeistand somethmm or need more help, there is a list of toll-free

consumer service numbers included in

the back section of this manual. OR

Visit our V_bsite at: ge.com

" tY

Write down the model & serial

n u 7yt Ders

You will find them on a lahel on the ceiling inside the bar refligerator with

icemaker.

Please write these numbers here:

Model Nmnher

Serial Number

Use these nmnbers in any correspondence

or serxice calls concerning y'our bar

refrigerator with icemaker.

Page 3

Consumer Inff)rmation

Bar I:b,,/rh{'erator, with I_emak_,r

If you received

a damaged

appliance

Save time

mon U

[[you

need

service

The warranty does not co_er damage caused afler'delive U.

gefbre you request serxice, check the It lists causes of minor operating problems Problem Sol, er in the back of this manual, that you can correct yourself.

Before using, be sure all packing materials and tape have been remoxed.

To assure no damage is done to the finish of the product, the safest way to remove the adhesixe left flom packaging tape on

To obtain serxice, see the Consumer Services page in the back of this manual.

_¢\b are proud of our service and want you to be pleased. If fbr some reason you are not happy' with the service you receixe, here are steps to fbllow fbr fllrther help.

b>_rcustomers in the USA:

FIRST, contact the people who serviced your appliance. Explain why you are not pleased. In most cases, this will solve the problem.

NEXT, if you are still not pleased, write all the details--including your phone

number--to:

Immediately contact the dealer (or

builder) that sold you the bar refrigerator with icemaker.

new appliances is an application of household liquid detergent. Apply with a soft cloth and allow to soak. Wipe d W and then apply an appliance polish m thoroughly clean and protect the surface.

For customers" in Canada:

FIRST, contact the people who serviced your appliance. Explain why you are not pleased. In most cases, this will solve the problem.

NEXT, if you are still not pleased, write

all the details--including your phone nmnber to:

Manager, Consumer Relations Camco Inc.

1 Factory Lane, Suite 310

Moncton, N.B. El C 9M3

After

installation

is cornpleted

Managei; Customer Relations

GE Appliances

Appliance Park

Louisville, KY 40225

* Promptly inspect your new Monogram

bar refiigerator with icemaker. If it has been damaged, contact the Installer or Dealer immediately.

* This bar refligerator with icemaker must

be properly lexeled to ensure correct door alignment, door closure and ice production. Contact the Installer if

the unit is not level.

* The trait should be centered in the

opening. In a standard 24" opening, the tiont face of the Stainless Steel door will

be flush with adjacent cabinet, y. The flont face of the Custom Panel door

should be 1,_A"fbrward of adjacent cabinet W. Contact the installer if

clearance is not correct.

* Test the door swing. Carefldly open and

close the door. The door should not rub or catch on adjacent cabinetry. Notit\/the

installer if the door makes contact with cabinetry.

Please Contact the Installer or Dealer if yon experience any of these problems.

Your custom panel (ZIBI240 model only)

bar refligerator with icemaker is shipped with two toekicks, a stainless steel and a

black toekick. For shipping purposes, one of the toekicks will be secured to the back

or on the inside of the unit, and the second will be installed on the unit. Keep

the unused toekick and other unused or removed parts tbr possible flmlre use.

Page 4

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INS TR UCTIONS

WARNINGmwhen .sing

this appliance, always exercise basic safety precautions, including the %llowing:

*Use this appliance only for its intended

purpose as described in this Owner's Manual.

*This bar refrigerator with icemaker must

be properly installed in accordance with the Installation Instructions before it is

used.

*Do not allow children to climb, stand

or hang on the shelves in the bar refrigerator with icemaker. They could damage the bar refligerator with icemaker and seriously i_!jure themseh'es.

*Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

*Keep fingers out of the "pinch point"

areas: clearances between the door and benveen the door and cabinet are

necessarily small. Be carefld closing the door when children are in the area.

*Unplug your bar refrigerator with

icemaker before cleaning or making repairs. NOTE: _¢\_ strongly recommend that any servicing be performed by a qualified individual.

+Before replacing a burned-out light bulb,

the bar refligerator with icemaker should be turned OFF or unplugged in order to

avoid contact with a live wire filament.

(A burned-out light bulb may break

when being replaced.)

+In bar refrigerators with automatic

icemakers, axoid contact with the moxing parts of the ejector mechanism, or with the heaong element located on the

bottom of the icemaker. Do not place fingers or hands on the

automatic icemaking mechanism while the unit is plugged in.

,DANGER: tUSK OF CHILD ENTRAPMI 2NT

Child entrapment and suftbcaOon are not problems of the past. Junked or abandoned refligeraOon products are soil dangerous...even if they will sit fbr 'just a fiJw days." Kyou are getting rid of your old appliance, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigeration Product:

*_E_ke off the doors. *Leave the shelves in place so that

children may not easily climb inside.

REHU(;ERANTS

All reKigeration products contain refligerants, which trader federal law must be removed prior to product disposal.

If you are getting rid of an old refrigeration

product, check with the company handling

the disposal about what to do.

Page 5

IMPORTANTES INSTRUCTIONS DE SI CURITI

LIRE ET CONSERVER CES INSTRUCTIONS

IkAVERTISSEMENT

Lorsque xous utilisez l'appareil, obserxez toujours certaines precautions

de base, notamment :

• N'utilisez I'appareil que pour son ttsage pr6vu, comme d6crit dans le pr6sent

man/lel.

• Installez le r6frig6rateur de bar avec machine a glagons conform6ment aux

directives d'installation avant de I'utiliser.

• Ne laissez pas les enfants grimper,

s'asseoir, se tenir debout ni se pendre aux clayettes du r6frig6rateur de bar

avec machine _t glaqons. Ils pourraient endommager le r_flig_rateur de bar avec machine _ glaqons et se blesser

gravement.

• N'entreposez et n'utilisez pas d'essence

ou amres vapeurs et liquldes inflammables /_ proximit6 de cet appareil ou de tout autre appareil 61ectrom6nager.

• Eloignez les doigts des parties du r6frig6rateur oi_ I'on peut facilement se pincer : les espaces entre les portes et entre les portes et ]es placards sont

toujours _troits. Soyez prudent lorsqne vous fermez les portes de l'appareil en presence des enfants.

• D6branchez votre rdfrigdrateur de bar avec machine a glagons avant de le nettoyer et de le r6parer. REMARQUE :

Nons vous recommandons vivement de confier toute r_parafion _ un technicien

qualifi_.

• Avant de remplacer une ampoule grill6e, le r_flig_rateur de bar avec machine g]aqons dolt &tre d_branch_ afin d'_viter

tout contact avec un fi] soils tension.

(Une ampoule grill_e pent se briser

pendant l'op_rafion).

*Dans les r6frig6rateurs de bar qul ont

une machine/_ glagons automatique, _vitez de toucher les pi&ces mobiles du nl_canisme d'_jecfion oil l'_l_,ment

chauffant situ_ en bas de la machine

glaqons.

Ne mettez jamais vos doigts ou vos mains sur le m6canisme de machine/_ glagons automatique quand votre r6frig6rateur

est branch&

,IkDANGER!

PJSQUES POUR LES ENFANTS

Les enfhnts pris an pi&ge oil morts Avant de vous ddbarasser de votre vieux d'asphyxie sont toujours d'acmalit6, appareil de r6frig6ration : Les appareils de r6flig_ration abandon6s sont to//jours aussi dangereux, re&me si on n'attend que "quelquejours" pour

s'en d_barasser. Si vous ne gardez pas wme ancien appareil, veuillez suivre les directives ci-dessous afin de pr6venir

les accidents.

REFRIGI?,RANTS

Toils les appareils de r_flig_ration confiennent des refligerants qui,

conform&nent aux lois f6d6rales, doivent &tre enlev_s avant toute _liminafion de

l'appareil.

*Ddmontez les portes. *Laissez les clayettes el/ place afin

d'emp_cher les enfimts de grimper _'tl'in t&ieur.

Si xous xous d_barrassez de xieux appareils

de r_flig_ration, x_rifiez, auprOs de la

soci_t_ qui s'occupe de lent _limination,

ce que xous dmez faire.

Page 6

IMPORTANT SAFETY INSTRUCTIONS

HOW TO CONNECT EIJ 2CTPJCITY

Do not_ under any circmnstances, cut or remove the third (ground) prong from tile

power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which males

with a standard 3-prong (grounding) wall outlet to minimize the possibility of elecnic

shock hazard flom this appliance. Have the wall outlet and circuit checked by a qualified elecuician to make sine

tl_e outlet is properly grounded. Where a standard 2-prong wall outlet

is encoun tared, it is your personal responsihility and obligation to have

it replaced with a properly grounded 3-prong wall outlet.

Use of a (-;H (Ground Fault Inmrrupter) is not recommended fbr the bar

refligerator with icemaker. The appliance should always be plugg>d

into its own individual electrical outlet which has a x>ltage rating that matches

the rating plato. This provides the best perfbnnance and also prevents overloading house wiring circuits which could cause a

fire hazard flom overheated wires.

DO NOT USE AN

ADAPTER PLUG

TO CONNECT THE BAR REFRIGERATOR WITH

ICEMAKER TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH

THIS APPLIANCE.

Never unplug an appliance by pulling on

the power cord. Always grip the plug firmly and pull straig]_t out flom the outlet.

Repair or replace immediamlv all power

cords that have become flaved or otherwise damaged. Do not use a cord that shows

cracks or abrasion damage along its length or at either end.

When moving the appliance, be careflfl

not to roll o_er or damage the power cord.

SA THESE INSTRUCTIONS

Page 7

IMPORTANTES INSTRUCTIONS DE SECURITE

RA CCORDEMEN7 ! IT ;CT't QUE

Ne coupez ni regwez en aurtm cas la troisibme broche (raise h la term) de la fiche du cordon d'alimentation. Pour volre srcuritr, cet

appareil dolt 6tre currectement mis h la term. Ix>coMon d'alimentation de cet apparel] est

muni d'une fiche _ ,3broches (raise f_la tene) qui se Nanche dans une prise mural or(finaiie a 3 a]v&)les (raise _ la terre) [×mr r_&fim au

minimum les risques du chocs _lectriques. Faites examiner la prise de courant et le circuit

par un _lectvicien qualifi_ pour vous assurer que la prise est conecmment raise _ la teire.

Si la prise murale est du type standard a 2 alv&)les, il vous incombe de la fifire remplacer par une prise a 3 alv&_les conecmment raise

fi la torte. L'appareil doit/oujours &tre branch_ dans

sa propre prise de courant, dont la mnsion nominale est identique ficelle indiqu_e sur la plaque signal6tique.

L'ufilisafion d'un disjoncmur de fifite fila mrre est recommand_e [xmr le re_fiJg&amur

de bar m,ec machine it glaqons. Cetm prScaufion est recommand_e pore

g;wantir un rendement opfinmm et &'imr

tree smvharge des ciivuits Olectriques de la

rOsidence, ce qui pounait crier un risque d'incendie par surschauffe des ills.

N'UT1L1SEZ JAMA1S

UNE PRISE A

ADAPTATEUR POUR LE

RI_:FR1GI_:RATEUR DE BAR

AVEC MACHINE

GLACONS A LINE PRISE B1POLA1RE.

N'UT1L1SEZ JAMA1S DE

RALLONGE AVEC CET

APPARE1L

Ne cDbtanchezjamais l'appareil en fimnt le coMon

d'alimenmfion. Saisissez fbnnement la fiche &l cordon et tirez droit pour la refirer de la prise.

R_parez on remplacez imm_diamment tout cordon efliloch_ ou endommag_. N'ufilisez pas un cordon fbndillO on pr_senmnt des

si_es d'usure.

Lorsque vous d_placez l'appareil, fidtes

attention de ne pas la fidre fouler sur le cordon d'alimenmtion afin de ne pas l'endommager.

CONSER VEZ CES DIPd'2CTII@2S

Page 8

Controls and Features

Bar I_J)'ig'r,rator witk I( emat,,r

7 mpevatuve

cont vl

Child control

lochout

Unit

ON/OI Y

The temperature display shows the actual mmperature of the bar refligerator with

icemaker. The actual mmperature may xary slightly flom the set temperature

based on factors such as door openings, amount of food and room temperature.

To change the temperature setting, press the WARMER or COLDER pads until you

reach the desired set temperature. After 5 seconds, the display will return to the actual temperature.

After making adjustments, allow 12 to 24 hours fbr the bar reflJgerator with icemaker to reach the temperature you have set and

befbre making any filrther adjustments.

This child control lockout tbature prevents unwanted changes to your

temperature settings.

This pad stops cooling in rite bar refrigerator with icemaker, turns off the temperature controls and remox_s power to the light circuit.

NOTE: The icemaker is on a separate on/off switch. To remove power flom the

icemaker See Au/omatic Icemaker section.

TEMP=CONTROL

®. ®. ltiJ

WARMER COLDER

NOTE:The icemaker temperature is not displayed.

Temperature Settings Minimum: 34°F (1.1°C) Maximum: 45°F (7.2°C)

After the desired temperature is set, the

temperature can be locked. To lock, press

both the + and - pads at the same time for

five seconds. To unlock, press both + and

- pads for five seconds.

Glass shelves

Press this pad %r a minimnn_ of 3 seconds to turn fl_e bar refligerator with icemaker on or off; or unplug the unit fbr long

w<afions or absences, or when cleaning the trait or changing the light bulb.

Tempered glass shelves in fl_e bar refrigerator wifl_ icemaker are removable %r easy cleaning or for storing larger items.

To remove a shelf, open the door completely to avoid potential damage to the gasket. Lift up on the back of the shelf slightly. Tilt the shelf to one side at an

angle while pulling forward.

Appearance mayvary

Toremove, lift upon the backof the shelf Tiltthe shelf at anangle while removing

or replacing

To replace a shelf, open the door completely to axoid pomnfial damage to

the gasket. Tilt the shelf to one side at an

angle and slide reward the back wall, placing one side onto the shelf support.

Place the other side onto tim opposite shelf

support. Ensure rear locking tabs are engaged. When installed properly, the shelf

will not slide forward when gently pulled.

Place in slots when replacingthe shelf

Page 9

Controls and Features

Bar Rr,,/*'iq'r,*'ato*', with I_emakr, r

Automatic

icemaher

The icemaker will produce sexen cubes per cycle--approximately 100-130 cubes in a 24-hour period, depending on freezer

compamnent mmperamre, room temperature, number of door openings

and other use conditions.

If the bar refiigerator with icemaker is operated befbre the water connection is made to the water salve, set the icemaker power switch to 0 (off).

When the unit has been connected to the water supply', set the icemaker power

switch to 1 (on). The green light will

COI?a e on.

The icemaker will fill with water when it cools to 15°F (-10°C). A newly installed bar refligerator with icemaker may take

12 to 24 hours to begin making ice cubes.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first fbw batches of ice to allow the water line to clear.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

If ice cubes get stuck in the icemaker,

the green power light will blink. To correct this, set the icemaker power switch

to O (off) and remove the cubes. Set the icemaker power switch to I (on) to restart

the icemaker.

After the icemaker has been turned on

again, there will be a delay of about 45 minutes befbre the icemaker resumes

operations.

NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one

batch of ice.

Power Switch

4""_ Icen]aker

Ice storage

bin

Be snre nothing interferes with the sweep of the feeler arm.

When the bin fills to the lexel of the feeler arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined together.

To remove, pull the icemaker drawer flfllv open and remoxe tim transportable ice storage bin by lifting up and out.

NOTE: Ice can fall behind the ice storage bin. Prior to replacing the bin, check for

any fallen ice.

If fl_e ice storage bin is removed fiom the refiig_rator for an extended period of time, we recommend setting the icemaker power switch to O (off).

To replace, grasp fl_e side of the right side of the bin with the higher edge so that the angled side is against the drawer front. Lower the 1)in into place and close the

drawer.

Green t

Power Light Feeler Arm

The ice storage 1)in is dishwasher safe, top

rack only.

CAUTION: Failure to install properly could cause potential damage to the

icemaker

Page 10

Controls and Features

Bar Rejri_'erator, with l( emak_,r

]('e S('O0 D

tips and suggestions

Removing

i .ll

extension drazvo"

The bar reDigerator with icemaker irrcludes an ice scoop in tile ice storage bin. To maximize ice bin capaciff, store tlle ice scoop as shown. Do NOT wash the ice scoop in the dishwashen For cleaning, handwash in mild soapy water or use tire baking soda solution nomd in Cleaning tlle

irrside section.

The bottom filll extension drawer holds fixe bottles and is loaded with necks timing

the rear. Tall bottles should not be loaded on the bottom drawer because they may

pre_ent the door from closing.

• Do not block the thermistor, located on the right hand side,just aboxe the top

shelf of the bar refl_igerator with icemaker. Blocking the thermistor could impair the air circulation and temperature control.

To remove:

1. Pull the fill] extension drawer out to the

STOP position.

2. Push tile tab on right drawer guide

down while pulling tile tab on left guide up, arrd pull tile drawer out.

To replace:

1. Push the drawer slide arm back into tile unit.

Bottom drawer arrangement

; w;UrShul2d;u.°,a°,nuTh

left drawer guide)

Appearance may vary

Interior jan

2. Pull the small slide sub-assembly

completely forward.

3. Insert tile sides of tile drawer back into tile guides.

4. Push until tile tabs lock irrto place.

The interior tim is located in the rear wall of tire bar refrigerator with icemaker

and is designed to run continuously to help maintain the proper cooling temperature.

Sub-assembly

Toreplace, push drawer slide Pullsmall slide sub-assembly arm back intounit completely forward

NOTE: Make sure tile tabs on tile flfll extension drawer guides are flflly engaged

before loading arty bottles. Pull tire drawers out all tire way to tire STOP position and

push back ira several times to make snre locking tabs are properly engaged.

In most instances, the interior fan will run

when the door is open. However, it will not operate when tile door is opened during a deflost cycle.

Page 11

Care and Cleaning

Bar R_/)'ige*'ator witk Icemat,,r

Turn the bar refrigerator with icemaker OFF or unplug the unit before cleaning. Turn tile bar refiigerator with icemaker OFF by pressing the button on tile control panel a minimum of 3 seconds until tile light turns off.

Gasket The main door and icemaker

compartment gaskets may lye cleaned with mild soap and wamr, a baking soda solution or a mild scouring powder. Rinse and di T well after cleaning.

Light bulb

_[dacement

In the event

4 apowe

failure

Turn the bar refiigerator with icemaker OFF before replacing tile light bulb.

If the power fails, open tile door as infiequently as possible to maintain the temperature.

For long vacations or absences, remove fbod and turn the bar refrigerator with

icemaker OFF. Clean tile inmrior (see Cleaning tile Inside section)

After cleaning tile gaskets, apply a thin layer of paraffin wax or petroleum jelly to

the gaskets. This helps keep tile gaskets

fiom sticking and bending out of shape.

To remoxe the ligl/t shield, pull the tab in

tile bottom center of the shield. Replace

with a 15 watt appliance bulb.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

For shorter vacations, remove perishable foods and leave controls at regular settings.

However, if the room temperature is

expected to drop below 60°F (16°C), follow the same instructions as fbr

long xacations.

Preparing

to _rtove

Set tile icemaker power switch to the 0 (off) position and be sure to shut off tile

water supply to the refligerator.

Secure all loose items such as shelves and Be sure the bar refrigerator with icemaker drawers by taping them securely in place stays in an upright position during moving. to prevent damage.

Page 12

Care and Cleaning

Bar R_/)'ige*'ator with Icemah_,r

Turn the bar refrigerator with icemaker OFF or unplug the unit before cleaning. Turn the bar refiigerator with icemaker OFF hy pressing the button on the control panel a minimum of 3 seconds until the light turns off.

Clearzirzg

the outside

Clearzirzg

the irzside

Door handles and trim--Clean with a cloth dampened with soapy wamr. DIT with a soft

cloth.

Keep the outside clean. Wipe with a clean cloth lightly dampened with mild liquid dish

demrgent. DIy with a clean, soft cloth.

Do not wipe the reflJg_ra/or with a soiled

dish clod/or wet towel. These may leave a residue that can damage the finish. Do

not use scouting pads, powdered cleaners, bleach or cleaners containing bleach

becalse these products can scra/ch and damage the finish.

Unplug" the bar refrigerator with icemaker before cleaning. If this is not practical, turn the unit OFF and wring excess moisture out of the cloth or sponge when cleaning around switches, lights or controls.

Use warm water and baking soda solution-- about a tablespoon (15 ml) of baking soda to a quart (1 liter) of wamr. This both cleans and neutralizes odors. Thoroughly rinse and wipe dry'.

Stai_fless Steel Regularly clean and polish the stainless steel exmrior and handle with

a commercially available stainless steel cleaner such as Stainless Smel Magic _'*

m preserve and promct the fine finish. Stainless Steel magdc is available fl_rough

GE Parts and Accessories, 800.626.2002 or ge.com. Order part n mnber _VX10X15.

To avoid scratching the fine finish of the stainless steal, wipe in the sane direction

as the grain when polishing or deaning any stainless steal surface. The grain on the bar

refrigerator with icemaker door runs top to bottom.

Do not use appliance wax or polish on the stainless steal.

Warranty does not cover damage due to

improper deaning methods.

Other parts of the bar refrigerator with icemaker--including the door gaskets, drawei; icemakei; ice scoop and glass

shelves---<an be cleaned the same way. Only the ice storage bin is dishwasher

safe, top rack only

Avoid cleaning cold glass shelves with hot water becattse the extreme temperature

difference may cause them to break. Handle glass shelves carefnlly. Rough handling of tempered glass can cause it to shatter.

Page 13

Built-In Dimensions

Bar I:b,,/riq'erator, with I_emaker

Installation

dimensions

stainless steel (ZIBS240 modal)

Tile bar refrigerator with icemaker can be a fleestanding model or can be buih in using

the cut-out dimensions beloxs:

23a/g' 23a/g'

(603ram) .,.]_,. 603mm

34V2"

(876ram)

-_/..

Product dimertsions:

Height: _ "

34/2 (876mm)

Width: _, /4 (603 ram) Depth: _, /4 (603 ram)

NOTE:

Handle and handle standoff

depth is 2'/4".

'_/_]]enbuilding in file bar refrigerator with

icemaket; be sure to allow for a flfll door

swing so you haxe flfll access to the pull-out

flfll extension vegetable pan.

See the Installation Instructions (Pub. No. 31-51544) for complete directions.

..... _xJ /j ¸

Cut-out dimensions:

Height: 34/2 (876 ram) minimum Width: 2, /4 (60: ram) minimum

3.... 3

Depth: 24" (610 ram)

Installation

dimensions

custom panel (ZIB[240 model)

Tile bar refrigerator with icemaker can be a fieestanding model or can be buih in using

the cut-out dimensions beloxsc

24W' 23a/d'

(632ram) _.,. (603ram)

34V2"

(876mm)

Product dimeltsions: Height: _ "

34/2 (876mm)

Width: _, /4 (603 ram)

NOTE:

Handle is not supplied.

Depth: 247/s" (632 ram)

_A]aen building ira file bar refrigerator with

icemakel; be sure to allow for a fifll door

swing so you have flfll access to file pull-out

fifll exmnsion vegetable pan.

See the Installation Instructions (Pub. No. 31-51544) for complete directions.

Cut-out dimensions:

Height: 34/2 (876 ram) minimum Width: 2, /4 (60: ram) minimum

] tl

3.... 3

Depth: 24" (610 ram)

Page 14

Built-In Dimensions/Installation

Bar I¢_qrigeralor wilh l_emal:er

The bat refrigerator Mtb icemaker is Pacto U set %r a l 10 ° door swing.

When in.stalled in a corner: Check tile model nmnber and allow the

appropriam clearance for tile 90 ° door swing and to allow racks to slide ont.

• ZIBS240 - 4" ndninmm to wall.

• ZIBI240 - 4-1/2" minimum to wall.

Check tile model number and allow tile at)propitiate clearance for tile 110 ° door

swlng.

• ZIBS240 - 14" minimum m wall.

• ZIBI240 - 16" minimum m wall.

NOTE: Clearances are based on the reconnnended 2-1/4" handle standoff depth. Ctlsmm handle clearances may vary

depending on the standoff of the custom handle.

Choose the location:

• These products may be closed in on tile

m I) and three sides as long as the front is

unobstrucmd for air circulation and

proper access m the dooi:

14" Minimum

toWall

(with Custom Panel

16"Min.)

'1 t

.... '\ii\

110° ..

90 Door Swing @-5/8"

...... ..[ ,,'..

4" Minimum

to Wall

(with Custom Panel

4-1/2" Min.)

• Do not install these products where the temperature will go below 55°F (13°(;)

or aboxe 90°F (32°(;).

• Do not install where it will be subject to

direct sunlight, heat or moisture.

Black or Stainless Steel Toekick Options Your custom panel (ZIBI240 model only) bar

refrigerator with icemaker is shipped with two mekicks, a stainless steel and a black

mekick. For shipping puq)oses, one of tile

toeMcks will be secmed to tile back or inside of tile unit, and file second will be installed on the unit. Kee I) file unnsed mekick and

other unused or removed parts for possible fimn_e use.

Installing

custom 3/4" door panel

and handh?

(ZIB[240 modal

3/4" Overlay Panel Dimension.s Model ZIBI240 requires a field-installed

oxerlay door panel.

• Tile ox>day panel must be secured to a l/4" thick backer panel fllat slides into rile

uim. A.I 0" thick spacer panel must be placed between tile overlay and backer panel.

• A custom handle of your choice, supplied

by your cabinet makei; must be installed on this oxerl W panel. Counmrsink all screws into tile backer panel. &rews cannot protrude flom tile backer panel.

NOTE: Maximmn total xseight for custom

r o

door panel is 25 pounds.

I 1/4" Ba(ker 2:4-:47' 6" 29-9/16"

0.10" Spacer 22-1/2" 29-1/16" a,40xmla 23-5/8" 30"

lay

Backer_ L.IO Inch

Panel Spacer

Page 15

Installation

Bat" IG_/rig'eralor with lcemaker

Installing

custom 3/4" door panel

and handle

(con t. )

(ZIB[240 model

Assemble overlay panels ..<._

l.,::e=, erspacerpa=d

on the backer panel, _, , left to right and top to

bottom. Secure the !_acker Panel!_-y panels with glue.

2. Center the spacer/backer panel on the

overlay panel. Secure with glue and screws. Countersink all screws into the backer

panel.

Custom Panel Hinge Routing Dimensions Use a 3/4" roumr bit to cut a notch

into die back side of the assembled panel 3/8" toward the flont of the o\'erlay panel, 3/4" deep and 7/8" wide.

screws into the backer panel. Screws cannot

protrude flom the backer panel.

ScrewsMust

BeCountersunk

IntoPanel

Ha!dlC_e

DoorPanels

4. Slide o_erlay panel into the door trim.

5. Reinstall the side tlJm using the tiJln screws relno_ed earlJei:

Install custom door panel and handle:

1. ()pen door to 90 °.

2. Remove 5 screws holding trim; lift off trim. Retain screws.

,'_.A custom handle of your choice, supplied

by your cabinet maker, must be installed onto the o_erlay panel befbre the panels

are slid into the trim. Com)tei_ink all

_- i =_ iiiiiiii

i iiii

-!I ........

iiiiiiii

i h_ !!!!!!!!

-io iiii

iiii

_° iiii

iiii

6. Place the brushed decorative coxer over the side trim to hide the screw heads.

Ensure side trim is aligned top to bottom and flont to back. Snap into place.

NOTE: For shipping puqx)ses, the brushed decorative cover will be secured

to the flont of the unit.

Page 16

The Problem Solver

Bar I¢_qi'ig'eralor with Icema/_er

No_'HZ(I_[

operating

SO_lgTt([S

Newer appliances sound difterent flom older appliances. Modern appliances have more features and use newer technology.

Do you hear what I hear? These sounds are normal.

HUMMM..,

WHIR./

-- WHOOSH...

The new high efficiency compressor may run fasmr and longer than your old appliance and you may hear a high- pitched hum or pulsaung sounds while it is operating.

Sometimes the appliance runs %i an extended period, especially when the doors are opened flequently.

You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the appliance.

The cabinet t_an runs confi*mously except when the door is opened.

You may hear the fans spinning at high speeds. This happens when the appliance is first plugged in, when the door is opened flequently or when a large amount of food is added to the appliance. The fans help maintain desired temperatures.

If the door is open t_1 over 3 minutes,

you may hear the fans come on in order

to cool the light bulbs. The fans change speeds in order to

provide optimal cooling and energy savinKs.

CLICKS, POPS,

CRACKS and CHIRPS

You may hear clicking, cracking or popping sounds when the appliance cools to the correct temperature or immediamly following defiost.

The electronic control board may cause a clicking som_d when relays activate to control appliance components.

Expansion and contraction of cooling coils during and after deflost can cause cracking or popping sounds.

After an icemaking cycle, you may hear

the ice cubes dropping into the ice bucket.

The flow of refrigerant through the fleezer cooling coils may make a gurgting noise like boiling wamr.

*¢\hmr dropping on the deflost hearer can cause a sizzling, popping or buzzing sound during the deflost cycle.

A water dripping noise may occur

during the deKost cycle as ice melts fiom the evaporator and flows into the drain pan.

Closing the door may cause a gurgling sound due to pressure equalization.

Page 17

The Problem Solver

Bar Rejriq'erator, with I_emaker

Questions ? Use this

problem

SO[_)e_'. !

PROBLEM POSSIBLE CAUSE

APPLIANCE DOES NOT OPERATE

VIBRATION OR RATTLING (Slight

vibration is normM.) COMPRESSOR

MOTOR OPERATES FOR LONG PERIODS

OR CYCLES ON AND OFF FREQUENTLY

FRESH FOOD COMPARTMENT

TOO WARM

FROST OR ICE CRYSTALS ON

REAR WALL

AUTOMATIC ICEMAKER

DOES NOT WORK

* Appliance may be in defl'ost cycle when compressor motor does not

operate tbr about 30 minutes.

* Appliance is so quiet that most of the time you will hear low or no

operating noise.

* Controls are set to OFE Press ON/OFF button on control panel

f_)r a lnillilntlln ()1_ .'4 secollds,

* If interior light is not on, appliance may not be plugged in

at wall oudet. Push the plug completely into the wall oudet.

,bThe fuse is blown/circuit breaker is tripped. Replace fuse or reset

the breaker.

* The appliance is in showroom mode. Unplug it and l)lu°_ it back in. * A({}ust the levelino_ legs, as shown in the Installation ]nstmcti(ms.

* Normal when appliance is first plugged in. _'\.dt 24 hours tor the

appliance to completely cool down.

* (-)tten occm's when large amotmts of food are placed in appliance.

This is normal.

* Door left open or package holding door open. * Hot weather or i/"equent door openings. This is normal. * Temperature control set at the coldest setting.

See Temperature Control

* Temperature control not set cold enough.

See Teinperature Control./kllow 12 to 24 hours flw teml)erattlre

to change.

* _'_,u'm weather or fi'equent door openings. * Door left open for hmg time. * Package may be holding door open. * Thermistor may be blocked, which can afl%ct the overall temperature.

The thermistor is located on the right hand side just above the top shelf.

* Too frequent or too hmg door openings. * Thermistor may be blocked, which can affect the overall temperature.

The thermistor is located on the right hand side just above the top shelf.

* Icemaker power switch is in the O (off) position. * _'\ater supply turned off or not c(mnected. See Installation hlstructi(ms. * Freezer coml)artment too warm. _Mlow 24 hours for the appliance

to completely cool down.

* Piled up cubes in storage bin cause icemaker to shut off.

Level cubes in bin.

* Ice cubes stuck in icemaker (green po>_er light on the icemaker is

blinkin *_ Turn off the icemaker, remove cubes and turn the icemaker back on.

Page 18

The Problem Solver

Bar Rejrifferator, with I_emaker

Questions ? Use this

problem

SO[_)e_'. !

PROBLEM POSSIBLE CAUSE

FREQUENT "BUZZING" SOUND

ICE CUBES HAVE ODOR/TASTE

SLOW ICE CUBE

* Icemaker power switch is in the I (on) position, but tile water supply

to tile appliance has not been connected or is kinked. Set the power switch to the O (off) position. Keeping it in tile I (on) position will

damage the water _dve or straighten the water supply line.

* Old cubes need to be discarded.

* Ice storage bin needs to be emptied and washed.

* Unsealed packages ill fl'esh fk)od compartment may be

transmitting odor/taste to ice cubes,

* Interior of appliance needs cleaning. See Care and Cleaning.

* Door n/a? have been left open.

FREEZING

APPLIANCE HAS ODOR

DOOR NOT CLOSING PROPERLY

* Interior needs cleaning. See Care and Cleaning. , Keep open box of baldng soda ill appliance; replace every 3 months.

* Door gasket is sticking or ti)lding over. Apply petroleum.jelly or

paraffin wax to the thce of tile gasket.

* Tile door is bitting an internal component inside the

appliance. At!just interior components to prevent interference.

MOISTURE FORMS ON OUTSIDE OF

APPLIANCE

* Not unusual during periods of high humidity. Wipe surfhce dry. * Door left open or package holding door open.

MOISTURE COLLECTS INSIDE

* Too frequent or too hmg door openings. e In humid weather; air carries moisture into appliance when doors

are opened.

INTERIOR LIGHT DOES NOT WORK

HOT AIR FROM BOTTOM OF

APPLIANCE

'_ No power at outlet. '_ I,ight bulb needs replacing. See Care and Cleaning.

* Normal air flow cooling motor: In the refl'igeration process, it is

normal that heat be expelled in the area trader tile appliance. Some floor coverings are sensitive and will discolor at these safb

and normal temperatures.

APPLIANCE NEVER SHUTS OFF

BUT TEMPERATURES ARE OK

ACTUAL TEMPERATURE

* Adaptive defl'ost keeps compressor running during door openings.

This is normal. Tile appliance will cycle off afier the door remains closed for two horn's.

* Normal opeF;itiOll ill extl'el//e tel//peF;lttlFeS,

* Unit just plugged in. Alh_w 24 horn's fi)r tile system to stabilize. e Door open %r too long. Allow 24 hours %r tile s*<stem to stabilize.

NOT EQUAL TO SET TEMPERATURE

,bWarm contents added to appliance. Allow 24 hours for tile system

to stabilize.

* Defi'ost cycle is ill process. Allow 24 hours fin" the system to stabilize. * Thermistor may be blocked, which can affect the overall temperature.

The thermistor is located on tile right hand side just above tile top shelf.

TEMPERATURE WILL NOT ADJUST

* Temperature may be ill lockout mode. Press both + and - pads fi)r

5 seconds to unlock tile temperatm'e.

* Thermistor may be blocked, which can affect the overall temperature.

The thermistor is located on tile right hand side just above the

top shelf.

Page 19

Consumer Services

Bar Rejri_'e*ator, with Icemakcr

With the purchase of your new Monogram appliance, receive the assurance that if you ever need information or assistance from GE, we will be there. All you have to do is call---toll-free?

G E Answer Center ®

In the USA:

800.626.2000

In-Home Repair

Service

In the USA:

800.444.1845

In Canada:

1.888.880.3030

For Customers

With Special

Needs...

In_e USA:

800.626.2000

Whatever wmr question about any Monogram major appliance, GE Answer Centei _)

inflwmation service is a_filable to help. Yore" call--and your question--will be answered promptly and courteousl> And you can call any time. GE Answer (;e*ltel _ service is open 24 horn> a day, 7 clays a week.

Visit our Website at: ge.com

In Canada, call 1.888.880.3030.

A GE consumer service professional will provide expert repair service, scheduled at a time

that's convenient for you. Many GE Const,lller Service company-operated locations ofl_br

yon se_Mce today or tomorrow, or at yore" convenience (7:00 a.m. to 7:00 p.m. weekdays,

9:00 a.m. to 2:00 p.m. Saturda):s). Our thctorv-trained technicians know your appliance inside and out--so most repairs can be handled in just one visit.

i r

GE offers Braille controls fl_r a variety of GE appliances, and a brochure to assist in planning a barrie>fl'ee kitchen for persons with limited mobility.

Consumers with impaired hearing or speech who have access to a TDD or a conventional teletypewriter ma,v call 800.TDD.GEAC

(800.833.4322) to request infl)rmation or service.

Service Contracts"

In the USA:

800.626.2224

In Canada:

1.888.880.3030

Par_ and Accesso_es

In the USA:

800.626.2002

In Canada:

1.888.880.3030

s_cTioN _A

You can have the secure Ieeling that GE Consumer Service will still be there after your warran D expires. Pro'chase a GE contract while your warrant_ is still in effect and you'll

receive a substantial discount. With a m ultiple-year contract, you're assured of future service at today's prices.

Individuals qualified to service their own appliances can have parts or accessories sent directly to their home. The GE parts system provides access to over 47,000 pa_qrs...and all GE Genuine Renewal Parts are hilly warranted. VISA, MasterCard and Discover cards are accepted.

User maintenance instructions contained in this manual cover procedures intended to be performed by amy user. Other servicing generally should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

Page 20

Warranty

Bar Refrifferator, with l( emaker

YOUR MONOGRAM BAR _FRIGERATOR WITH ICEMAKER WARRANTY

Staple sales slip or canceled check here. Proof of original purchase date is needed to obtain service under warranty.

WHA T IS

COVERED From the Date

0/ the Original Purchase

WHAT IS NOT

COVERED

LIMITED ONE-YILa_R WARRANTY For oue y(ar fl'(/m dale of original lmr(hase, we _ill provide, fi'ee of charge, parts and s(r_ice labor in ?Ill r

boule lo r(l/air or replace an) part (!like unit lhaI tails l)((ause of a mmmth(mring dell(1. LIMITED FIV_5-YEAR WARRANTY

For fi,,e ,_ears. trom date of origim'd pm:clmse, we will pro,,ide, t]°e( ot charg(, i)arts and service labor

ill \O/U" bol/le |o rel)air or repl_ice glib] par[ (!j'l]z(, fea[(_([ !7_ iJ_z,r(ltil_" 5fl(,llz (tb( colIll)l'( ssor , COlldeus(r,

exaporalor and all comle(ting robing) lhal t_'dls because of a im'mut_'_cmring detect.

This warramx is extended to the o;iginal purchas(r and any succeeding owmr lor prod ucts pro'chased lor ordinary holn( use in the 48 mainland states, Hawaii, Washington, D.C. or Canada. If the product is hxat(d

in an area where service l)} a GE Authorized Ser_ic(r is not a_ailal)l(, you m_ty be responsil)le lor a _rip charge or you may I)e required to bring the produ(t to an Authorized (;E Service locadon li)r service. /n

Alaska tb( warranty is the same except that it is I,IM [TED because vou umst pay to ship tile product to tile service sllop or Ior tile service teclluiciall's trine/costs to your llol/le.

All warranty service will 1)e proxid(d bv our Fa(torv Service Centers or by our authorized Customer (;are (' servicers during m)rmal working hours.

Sho/lM your appliance need service, during warramy period or l)(yomt, in the IISA call 800.444.1845. /n Canada: 888.880.3030. Please hay( your se;ial mmfl)er and model munber a_ailal)le when calling lot service.

* Service trips to your home to teach you how

to use the product.

'_Replacement of house fuses or resetting of circuit

breakers.

* Damage to the product caused by accident, fire,

floods or acts of God.

* Failure of the product if it is used for other thm_

its intended purpose or used commercially.

,_Damage caused after delivery.

* Improper installation, delivery or maintenance.

If yon have ml installation problem, contact your dealer or installer. You are responsible for

providing adequate electrical, plumbing and other connecting facilities.

* Replacement of the light bulbs, if included. * Loss of food due to spoilage (in the USA tufty).

'_Incidental or consequential damage caused by

possible defects with this applimlce.

* Product not accessible to provide required

service.

197D5891P013 49-60435

11-05 JR Printed in Slovenia

EXCLUSION OF IJl4PLIED WARJ_AN'IYES Your sole and exclusive remedy is product repair as provided in I

this Limited Wmv'anly. Any implied wmv'anties, including the implied warranties of merchantability or fitness

for a pmqic_lar purpose, are limited to one year or the shortest period allowed by law.

S()me states/provinces do not allow the exclusion or liufitation of iucidemal or consequential damages, so the al)ox( limitation or exclusion may not apply to you. This warramy gdxes you spe(ific legal fights, aml you

may also hm'e other rights which xarv ti'om state to state!province to provim:e. To kmlw what your legal " rights ar( in your state!province, c(msuh your local or state!provincial cousumer althirs otlice or your state's Attorney (;eneral.

Warrantor in USA: General Electric Company,

Louisville, KY 40225

Warrantor in Cmlada: Camco Inc.

GE Consumer & Industriol Applionces

General Electric Compon U Louisville, KV/40225

ge.com