GE ZET3038SH4SS, ZET3058BH4BB, ZET3058BH5BB, ZET3058SH4SS, ZET3058SH5SS Installation Guide

sta ati

" uilt-ln TrivectionTM

str cti

Oven

JT930, JT980, ZET3038, ZET3058

I_ Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com I

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer- Be sure to leave these
instructions with the Consumer.

• Note to Consumer- Keep these
instructions for future reference.

• Skill level - Installation of this appliance
requires basic mechanical and advanced

electrical skills.

• Completion time- 1 to 3 hours

• Proper installation is the responsibility of
the installer.

• Product failure due to improper installation
is not covered under the Warranty,

WARNING - Thisappliance must

be properly grounded,

FOR YOUR SAFETY:

• Be sure your oven is installed properly by a
qualified installer or service technician.

• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.

Never allow anyone to climb, sit, stand or
hang on the oven door.

• Make sure the cabinets and wall coverings
around the oven can withstand the

temperatures (up to 200°F) generated

by the oven.

-&WARNING: The electrical power to

the oven supply line must be shut off while
line connections are being made. Failure to
do so could result in serious injury or death.

• To prevent damage to the door and to

prevent excessive microwave leakage, do
NOT remove the door on the single wall

oven or the upper oven door on the double
wall oven.

• ATTENTION INSTALLER

All electric wall ovens must be hard wired
(direct wired) into an approved junction

box. A plug and receptacle is NOT
permitted on these products,

31-10663 1-07 JR

Installation instructions

PREPARE TO INSTALL THE OVEN

TOOLS YOU WILL NEED

Drill with 1/8" Bit

(Extension may be

required)

Straight Edge or

Adjustable Wrench

(for 1-7/16" Nut)

Phillips Screwdriver

Tape Measure

PARTS INCLUDED

Metal
Bottom Trim

Safety Glasses

12 Screws

Plastic
Bottom Trim

Square

OR

Pencil

Level

Metal Bottom

Trim Assembly

Gloves

Hand or Sabre Saw

MATERIALS YOU MAY NEED

Strain Relief
Clamp for 1/2"

conduit

60" of String for Single Ovens

96" of String for Double Ovens

Junction Box Wire Nuts

2

Installation instructions

PRE-INSTALLATION

All installation information on the following
pages is to be used for SINGLE and DOUBLE

oven installation[

Remove packaging materials. Check

behind hinges. Remove plastic on trims
and panel, all tape around the oven, and
any shipping screws securing the oven
to the base pad. Use caution when lifting

the oven forward; the ovens are front

heavy.

PRE-INSTALLATION (CONT.)

NOTE: To prevent damage to the door and

to prevent excessive microwave leakage, do

NOT remove the door on single wall oven

models or the upper oven door on double
wall oven models.

[_] The lower oven door on the double

wall oven may be removed as an added
convenience during installation.
See Step 4.

DO NOT LIFT THE OVEN BY THE HANDLE[

B£ Place the oven on a table or platform

even with the cutout opening. (Platform
must support 225 Ibs. single, 375 Ibs.

double.)

Remove the bottom trim from the top of
the oven. It will be installed at the end of

the installation process.

Oven Racks

Broiler Pan Literature
and _

Grid Pack

[]

Open oven door and remove literature

pack, broiler pan and grid, and oven

racks.

Remove Installation Instructions from

literature pack and read them carefully

before you begin.

@

Be sure to place all literature, Owner's

Manual, Installation Instructions, etc. in a
safe place for future reference.

3

Installation instructions

SINGLE BUILT-IN OVEN CUTOUT OPTIONS

_-I CUTOUT OPTIONS FOR SINGLE

BUILT-IN OVENS

Skip to Step 3 for Double Built-In Oven models.
There are 4 installation options for single built-in ovens.

Choose the appropriate one for your application:
_] WALL MOUNT--SINGLE BUILT-IN OVEN OPTION
_'] WALL MOUNT--SINGLE BUILT-IN OVEN BELOW

AN ADVANTIUM TM OVEN OPTION

_'] WALL MOUNT--SINGLE BUILT-IN OVEN ABOVE

A WARMING DRAWER OPTION

FD] UNDER COUNTER--SINGLE BUILT-IN OVEN

OPTION

WALL IVIOUNTmSINGLE BUILT-IN OVEN

[]

OPTION

Cutout Width

28 1/2" Min

,< 28 5/8" Max.

All corners must
be cut square

Allow 11/16" for
overlap of oven
over side edges

of cutout

3 1/2"

Required Junction
Box Area

r-_ WALL IVIOUNTmSINGLE BUILT-IN OVEN

OPTION (CONT.)

NOTE: If the cabinet does not have a front
frame and the sides are less than 3/4" thick,

shim both sides equally to establish the
cutout width.

If the cabinet does not have a solid bottom,
two braces or runners must be installed level

with the bottom of the cutout to support the
weight of the oven. For single ovens, the
runners and braces must support 225 Ibs.

The solid bottom or runners must be level

with the bottom of the cutout or the bottom

trim may not install correctly and then
interfere with the door opening.

--2" x 4" or
equivalent

runners
level with

bottom of
cutout

Suitable
Bracing to

Support
Runners

1" minimum

I for overlap of oven

Allow a minimum of L
21" for clearance to

adjacent corners, I bottom of cutout
drawers, walls, etc.

when door is open Cabinet

Cabinet Width

| to and 1 1/4"

overlap

F

of

Width 30"

oven

30"

Recommended

Cutout Location
from Floor

Cutout Depth
Cutout Width

32 112"
23 1/2" Min.
28 1/2" Min.

28 518"Max.

Cutout Height

27 1/4" Min.
27 5/16" Max.

NOTE: This oven is not approved for
stackable or side by side installation.

Recommendec

cutout location
from floor
32 1/2"

4

Installation instructions

_'] WALL MOUNTmSINGLE BUILT-IN OVEN

BELOW AN ADVANTlUM OVEN OPTION

i_ ............. M in...........

30" .......... _:;_ ....... 24"

..I..___"1_"1 all four sides

-------z.

Construct
solid bottom

min. 3/8"

/plgwood

by2x4orl

supported
x 2 runners,

" ./---

2" Min.

_'] WALL IVIOUNTmSINGLE BUILT-IN OVEN

ABOVE A WARMING DRAWER OPTION

_,t 23 1/2" Min.

...... inside

Construct
solid bottom

min. 3/8"

plywood

• When installed over a single wall oven,
allow at least 2" between the two openings.
This separation will provide clearance for
bottom overlap of the Advantium oven and
top overlap of the single wall oven.

• If you are replacing a GE/Monogram electric
double oven with the combined installation

of an Advantium and single wall oven, the
middle rail separating the two openings
may need to be larger than the 2" min.

shown.

• Always maintain 36 3/4" min. distance from
the floor to the Advantium oven cutout in

any installation combination.

• When installed in combination with a

GE/Monogram single wall oven, use
separate electrical junction boxes.

• Refer to Advantium oven installation
instructions for electrical requirements and

installation details of that product.

• Advantium ovens are approved for
installation above only certain specified

wall oven models. See the label attached
to the top of the oven for approved

Advantium oven models.

Bottom of warming drawer must be 1"
above toekick

• A 2" min. clearance between oven and
warming drawer cutouts is required.

• Additional clearance may be required if
2 x 4 blocks are used to support the solid

floor of the oven above. Check to be sure
that oven supports above the Warming

Drawer location do not obstruct the
required interior depth and height.

• Refer to warming drawer installation

instructions for electrical requirements and
installation details of that product.

• Warming drawers are approved for

installation below only certain specified

wall oven models. See the label attached to
the top of the oven for approved warming

drawer models.

NOTE: A single wall oven can be installed in
combination with the Advantium oven above

and a warming drawer below as long as the
dimensions and information on this page are
applied to the combination installation.

5