GE ZET2, ZET1 User Manual

Download

Page 1

Installation

30” Built-In Wall Oven

ZET1, ZET2

Instructions

If you have questions, call 1.800.GE.CARES or visit our website at: ge.com

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT—Save these

instructions for local inspector’s use.

• IMPORTANT—Observe all

governing codes and ordinances.

• Note to Installer—Be sure to leave these instructions with the consumer.

• Note to Consumer—Keep these instructions for future reference.

Parts Included

(2) 5/8″

(4) 3/4″ Wood Screws

Wood Screws

• Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty.

• NOTE—This appliance must be properly grounded.

• ATTENTION INSTALLER

All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products.

Materials Needed

Wire Nuts

Strain Relief Clamp for 1/2” conduit

Junction Box

31-10633 12-05 JR

Metal Bottom Trim Assembly

Tools Needed

1/8” Drill Bit and Electric or Hand Drill

Adjustable Wrench

36” of String

Phillips Screwdriver

Page 2

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

For Your Safety

• Be sure your oven is installed properly by a qualified installer or service technician.

• Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.

• Make sure the cabinets and wall coverings around the oven can withstand the temperatures (up to 200°F) generated by the oven.

WARNING:

power to the oven supply line

must be shut off while line connections are being made. Failure to do so could result in serious injury or death.

The electrical

AVERTISSEMENT :

Vous devez couper l’alimentation

électrique du four avant de le brancher. Le défaut de se conformer à cette procédure peut entraîner des blessures sévères et même la mort.

Electrical Requirements

These Monogram built-in ovens require a separate, properly grounded 3-wire 120/208 or 120/240 volt, 60 Hz power supply, protected by a time delay fuse or circuit breaker.

•

Double ovens are rated at 8.6 KW at 240 volt and 7.8 KW at 208 volt.

•

Single ovens are rated at 4.3 KW at 240 volt and 3.9 KW at 208 volt.

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate.

Rating Plate Location

We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician. After installation, have the electrician show you where your main oven disconnect is located.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition. If there are no local codes, your oven must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70–Latest Edition. You can get a copy by writing:

National Fire Protection Association Batterymarch Park Quincy, MA 02269

Effective January 1, 1996, the National Electrical Code requires that new, but not existing, construction utilize a four-conductor connection to an electric oven. When installing an electric oven in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION.

You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used.

Page 3

Installation Instructions

Pre-Installation Checklist

ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLE AND DOUBLE OVEN INSTALLATION!

Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.

Rack Supports with Hex Nuts

Open oven door and remove literature pack, broiler pan and grid, oven racks, rack supports and a bag with 9 hex nuts.

Read Installation Instructions carefully before you begin.

Be sure to place all literature, Owner’s Manual, Installations, etc. in a safe place for future reference.

Temperature Probe

Broiler Pan and Grid

Oven Racks

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

properly grounded (if applicable). Before you begin-Read these

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

instructions completely and carefully.

carefully.

carefully. IMPORTANT- Save these

IMPORTANT- Save these

IMPORTANT- Save these instructions for local inspector’s use.

instructions for local inspector’s use.

IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

EASY INSTALLATION OF YOUR NEW

Before you begin-Read these instructions completely and carefully.

Before you begin-Read these instructions completely and carefully. IMPORTANT- Save these instructions for local inspector’s use.

IMPORTANT- Save these instructions for local inspector’s use.

30" WALL OVEN

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer. OWNER- Keep these instructions for future reference.

OWNER- Keep these instructions for future reference.

Before you begin-Read these instructions completely and carefully.

Note- This appliance must be properly grounded (if applicable).

IMPORTANT- Save these instructions for local inspector’s use.

IMPORTANT- Save these instructions for local inspector’s use. IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer.

Note to Installer- Be sure to leave these instructions with the consumer. OWNER- Keep these instructions for future reference.

OWNER- Keep these instructions for future reference.

FOR YOUR SAFETY

Note- This appliance must be properly grounded (if applicable).

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

instructions completely and carefully.

carefully.

FOR YOUR SAFETY

IMPORTANT- Save these

instructions for local inspector’s use.

Before you begin-Read these

IMPORTANT- OBSERVE ALL

instructions completely and

GOVERNING CODES AND ORDIANCES.

carefully.

Note to Installer- Be sure to leave

IMPORTANT- Save these

these instructions with the consumer.

instructions for local inspector’s use.

OWNER- Keep these instructions

IMPORTANT- OBSERVE ALL

for future reference.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

these instructions with the consumer. OWNER- Keep these instructions

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

instructions completely and carefully.

carefully.

carefully. IMPORTANT- Save these

IMPORTANT- Save these

IMPORTANT- Save these instructions for local inspector’s use.

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

these instructions with the consumer.

OWNER- Keep these instructions

for future reference.

Note- This appliance must be

properly grounded (if applicable).

30" WALL OVEN

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

carefully.

carefully. IMPORTANT- Save these

IMPORTANT- Save these

IMPORTANT- Save these instructions for local inspector’s use.

instructions for local inspector’s use.

IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

these instructions with the consumer.

these instructions with the consumer. OWNER- Keep these instructions

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

properly grounded (if applicable). Before you begin-Read these

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

instructions completely and carefully.

carefully.

carefully. IMPORTANT- Save these

IMPORTANT- Save these

IMPORTANT- Save these instructions for local inspector’s use.

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

ELECTRICAL REQUIREMENTS

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

instructions completely and carefully.

carefully.

carefully. IMPORTANT- Save these

IMPORTANT- Save these

IMPORTANT- Save these instructions for local inspector’s use.

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

these instructions with the consumer. OWNER- Keep these instructions

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

properly grounded (if applicable). Before you begin-Read these

Before you begin-Read these

Before you begin-Read these instructions completely and

instructions completely and

instructions completely and carefully.

carefully.

carefully. IMPORTANT- Save these

IMPORTANT- Save these

IMPORTANT- Save these instructions for local inspector’s use.

instructions for local inspector’s use.

instructions for local inspector’s use. IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL

IMPORTANT- OBSERVE ALL GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES.

GOVERNING CODES AND ORDIANCES. Note to Installer- Be sure to leave

Note to Installer- Be sure to leave

Note to Installer- Be sure to leave these instructions with the consumer.

these instructions with the consumer.

these instructions with the consumer. OWNER- Keep these instructions

OWNER- Keep these instructions

OWNER- Keep these instructions for future reference.

for future reference.

for future reference. Note- This appliance must be

Note- This appliance must be

Note- This appliance must be properly grounded (if applicable).

properly grounded (if applicable).

Graphite Lubricant

Literature Pack

(Continued on following page)

Page 4

Installation Instructions

Pre-Installation Checklist cont.

To Remove the Door (if necessary)

Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door:

Open the oven door as far as it will go.

Hinge

Push both hinge locks down toward the door frame, to the unlocked

Hinge

Slot

Hinge

Unlocked

Unlocked Position

Position

position. This may require a flat blade screwdriver.

Hinge

Arm

DO NOT LIFT THE DOOR

BY THE HANDLE!

Place hands on both sides of the door, and close the oven door to the removal position, which is most of the way.

Place the oven on a table or platform even with the cutout opening. (Platform must support 175 lbs. [79 kg] single, 350 lbs. [159 kg] double.)

Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit.

Removal Position

Lift door up and out until the hinge arms clear the slots.

Hinge Clears Slot

NOTE: The oven door is very heavy. Be sure you have a firm grip before lifting the oven door off the hinges. Use caution once the door is removed. Do not lay the door on its handle. This could cause dents or scratches.

Page 5

Installation Instructions

ALLOW 11/16" FOR

OVERLAP OF THE

OVEN OVER SIDE

EDGES OF CUTOUT

ALLOW A MINIMUM

Allow a minimum

OF 21" FOR CLEARANCE

of 21” (53.3 cm) for

TO ADJACENT CORNERS,

clearance to adjacent

DRAWERS, WALLS ETC.

WHEN THE DOOR IS OPENED.

corners, drawers, walls, etc. when door is open

Cutout for Single Built-In Oven

Allow 11/16” (1.75 cm) for overlap of oven over side edges of cutout

21”

21"

(53.3 cm)

Cutout

Width

28 1/2” Min.

CUTOUT

28 5/8” Max.

WIDTH

(72.4 to

28 1/2" MIN.

72.7 cm)

28 5/8" MAX.

Opening Between

THE OPENING

Inside Walls

BETWEEN INSIDE

Must Be

WALLS MUST

At Least

BE AT LEAST

28 1/2"WIDE

28 1/2” (72.4 cm) Wide

Allow 1” (2.5 cm)

ALLOW 1" FOR

OVERLAP

minimum for

ON OVEN TOP

overlap of oven

AND BOTTOM

top and 11⁄

OF CUTOUT

(3.2 cm) overlap

of oven bottom

of cutout

CABINET

Cabinet

30” (76.2 cm)

WIDTH

30"

Width

Cutout

CUTOUT

Height

HEIGHT

27 1/4” Min.

27 1/4" MIN.

27 5/16" MAX.

27 5/16” Max. (69.2 to 69.3 cm)

RECOMMENDED

Recommended

CUTOUT

minimum cutout

LOCATION

32 1/2"

location from

FROM THE

floor 32 1/2” (82.6 cm)

”

FLOOR

5”

(12.7 cm)

JUNCTION BOX

Junction Box

LOCATION

Location

22" TO

22” (55.9 cm)

BOTTOM OF

to Bottom of

Junction Box

Cabinet Width 30” (76.2 cm) Recommended

Minimum Cutout Location from Floor 32 1/2” (82.6 cm)

Cutout Depth 23 1/2” (59.7 cm) Min. Cutout Width 28 1/2” (72.4 cm) Min.

28 5/8” (72.7 cm) Max.

Cutout Height 27 1/4” (69.2 cm) Min.

27 5/16” (69.2 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.

If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For single ovens, the runners and braces must support 175 lbs. (79 kg).

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.

Install a

2" x 4" or EQUIVALENT

solid bottom

RUNNERS

or 2” x 4” (5 cm x 10 cm) or equivalent runners level with bottom of cutout

Suitable Bracing to Support

SUITABLE

Runners

BRACING TO SUPPORT RUNNERS

21 5/8"

21 5/8”

OVER CENTERLINE

(54.9 cm)

OF CABINET

Over Centerline

of Cabinet

The solid bottom or runners must be level with the bottom of the cutout, or the bottom trim may not install correctly and then interfere with the door opening.

This oven is not approved for stackable or side by side installation.

Page 6

Installation Instructions

UITABLE RACING O SUPPORT UNNERS

2" x 4" or EQUIVALENT RUNNERS

21 5/8"

OVER CENTERLINE

OF CABINET

Allow a minimum

ALLOW A MINIMUM OF 21"

of 21” (53.3 cm) for

FOR CLEARANCE TO

clearance to adjacent

ADJACENT CORNERS,

corners, drawers,

DRAWERS, WALLS ETC.

walls, etc. when

WHEN THE DOOR

door is open

Cutout for Double Built-In Oven

ALLOW 11/16"

FOR OVERLAP

Allow 11/16”

OF THE OVEN

OVER SIDE EDGES

(1.8 cm) for

OF CUTOUT

overlap of oven over side edges of cutout

IS OPENED.

21”

21"

(52.3 cm)

Cutout

Width

28 1/2”

CUTOUT

(72.4 cm) Min.

WIDTH

28 1/2" MIN.

28 5/8”

28 5/8" MAX.

(72.7 cm) Max.

Opening Between Inside Walls Must Be At Least

THE OPENING

BETWEEN INSIDE

28 1/2”

WALLS MUST

(72.4 cm)

BE AT LEAST

Wide

28 1/2"WIDE

Allow 1” (2.5 cm)

minimum for

overlap of oven

ALLOW 1" FOR

top and 11⁄

OVERLAP

(3.2 cm) overlap

ON OVEN TOP

of oven bottom

AND BOTTOM

of cutout

OF CUTOUT

”

(12.7 cm)

Cutout Height 51 13/16”

CUTOUT

(131.6 cm) Min.

HEIGHT

51 15/16”

51 13/16" MIN.

(131.8 cm) Max.

51 15/16" MAX.

5”

Junction Box

JUNCTION BOX

Location

LOCATION

47” (119.4 cm)

47" TO

to Bottom of

BOTTOM OF

JUNCTION BOX

Junction Box

Cabinet Width 30” (76.2 cm) Recommended

Minimum Cutout Location from Floor 12” (30.5 cm)

Cutout Depth 23 1/2” (59.7 cm) Min. Cutout Width 28 1/2” (72.4 cm) Min.

28 5/8” (72.7 cm) Max.

Cutout Height 51 13/16” (131.6 cm) Min.

51 15/16” (131.8 cm) Max.

NOTE: If the cabinet does not have a front frame and the sides are less than 3/4” (1.9 cm) thick, shim both sides equally to establish the cutout width.

Recommended

RECOMMENDED

30”

30"

(76.2 cm)

CABINET

Cabinet

WIDTH

Width

CUTOUT LOCATION

minimum cutout location

12" FROM THE FLOOR

from floor 12” (30.5 cm)

If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For double ovens, the runners and braces must support 350 lbs. (159 kg).

NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered.

Install a solid bottom or 2” x 4” (5 cm x 10 cm) or equivalent runners level with bottom of cutout

Suitable Bracing to Support Runners

21 5/8”

(54.9 cm)

Over Centerline

of Cabinet

The solid bottom or runners must be level with the bottom of the cutout, or the bottom trim may not install correctly and then interfere with the door opening.

Page 7

Installation Instructions

Cutout for Single Built-In Oven Under Counter

Gas or electric cooktops may be installed over this

Gas or electric cooktops may be installed over this oven.

oven. See cooktop installation

See cooktop installation

instructions for cutout size.

See label on top of oven for

approved cooktop models.

25”

25"

(63.5 cm)

Top and/or side

Top and/or side fillers

fillers may be

may be necessary

necessary if

if unit is positioned

unit is positioned

between existing

cabinets. Be sure

they are attached securely, since they

they are attached

will anchor the oven

securely since

in the cabinet.

they will anchor the oven in the cabinet.

28 1/2" MIN.

28 1/2”

28 5/8" MAX.

(72.4 cm) Min. 28 5/8” (72.6 cm) Max.

27 1/4”

27 1/4" MIN.

(69.2 cm) Min.

27 5/16" MAX.

27 5/16” (69.2 cm) Max.

240V / 208V

Junction Box

Location

Allow 11/16"

Allow 1” (2.5 cm) overlap top of

Overlap Top

oven and

of Oven &

11/16” (1.8 cm)

Side Edges

overlap side

of Cutout

edges of cutout

5”

(12.7 cm)

Gas and electrical connections for 30" gas cooktop must be

Gas and electrical connections for

located in an adjacent accessible

30” (76.2 cm) gas cooktop must be located in an adjacent accessible

location to the right. For a 36"

location to the right. For 36” (91.4 cm)

gas cooktop the connections

gas cooktop, the connections may be

may be made to the left.

made to the left.

22" MIN.

22” (55.9 cm)

Above

Min. Above Support

Support

Platform

36"

36” (91.4 cm) Typical

Typical

Countertop

Height

3/4" Support

3/4” (1.9 cm)

Platform

Support Platform

Required

MUST SUPPORT 150 LBS.

MUST SUPPORT 175 LBS.

(78.8 KG)

24"

24”

(61 cm)

5 9/16” (14.2 cm)

5 9/16"

Reference dimension for

Reference dimension

maximum support height with

for maximum support height

typical 36” (91.4 cm) countertop

with typical 36" countertop

height

This oven is not approved to be installed under a solid disk, induction or downdraft modular cooktop. See the label on the top of the oven for approved models.

Page 8

Cabinetry

Single Oven Cutout for Installation Over a Monogram Warming Drawer

27 5/16” (69.2 cm) Max.

9” (22.9 cm) Max.

1” (2.5 cm) Min. Above Toekick or Adjust to Oven Installation Height

NOTE: Additional clearances between cutouts

may be required. Check to be sure the oven supports above the Warming Drawer location

do not obstruct the required interior 23 1/2” (59.7 cm) depth and 9 1/4” (23.5 cm) height.

• These Monogram Ovens require 3/4” (1.9 cm) overlap on both sides. Allow 1” (2.5 cm) Min. for top overlap and clearance to upper doors.

23 1/2” (59.7 cm) Min. Inside

9 1/4” (23.5 cm).

28 1/2” (72.4 cm).

2” x 2” (5 cm x 5 cm) or 2” x 4” (5 cm x 10 cm) Anti-Tip Block Against Rear Wall, 9” (22.9 cm) From Floor to Bottom of Block

2” (5.1 cm) Min.

Allow 5/8” (1.5 cm) Overlap on All Sides

NOTE: Install the

oven only with specific models listed on the label located on top of the oven.

Double Oven Cutout for Installation Over a Monogram Warming Drawer

51 15/16” (131.8 cm) Max.

9” (22.9 cm) Max.

1” (2.5 cm) Min. Above Toekick

• The Monogram Warming Drawers require 5/8” (1.6 cm) overlap on all sides.

• When installing a Monogram Warming Drawer below a single or double oven, a separate 120V, 60 Hz, properly grounded receptacle must be installed. Refer to installation instructions packed with the Warming Drawer for specific installation requirements.

23 1/2” (59.7 cm) Min. Inside

9 1/4” (23.5 cm).

28 1/2” (72.4 cm)

2” x 2” (5 cm x 5 cm) or 2” x 4” (5 cm x 10 cm) Anti-Tip Block Against Rear Wall, 9” (22.9 cm) From Floor to Bottom of Block

2” (5.1 cm) Min.

Allow 5/8” (1.5 cm) Overlap on All Sides

Cutout for Frameless Cabinets

Frameless Cabinets

Whenever possible, order 30” (76.2 cm) frameless cabinet with the cutout sided to fit the oven. If using stock cabinets, additional finished filler pieces may be required to cover the opening.

• A stock frameless cabinet cutout width may be up to 28 3/4” (73 cm). If necessary, add 1/2” (1.3 cm) cleats to the sides, flush with the front edge of the side panels to

accept mounting screws.

30”

(76.2 cm)

Install 1/2” (1.3 cm) Cleats to Hold Oven Mounting Screws

Double 51 15/16” (131.8 cm) Single 27 5/16” (69.2 cm)

28 1/2” (72.4 cm)

Min.

28 5/8” (72.7 cm)

Max.

Cabinet Depth 23 1/2” (59.7 cm) Min. From Inside Back to Front of Cabinet Frame or Side Panel

3/4” (1.9 cm) Min. Thick Bottom Shelf Cut Back Flush with Front of Side Panel

Page 9

Cabinetry

Single Oven Cutout for Installation Below a Monogram Advantium Oven

Per Advantium Requirement

27 5/16”

45 1/4” (114.9 cm)

NOTE: The middle rail separating the two

openings may need to be larger than the 2” (5.1 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.

Combined Advantium and Wall Oven Installation:

When installed in combination with a Monogram single wall oven, use separate electrical junction boxes.

• Refer to the Advantium oven installation instructions for electrical requirements of that product.

• These connections must be made by a qualified electrician. All electrical connections must meet National Electrical Code or prevailing local codes.

(69.2 cm) Max.

23 1/2”

(59.7 cm)

Min.

Inside

28 1/2” (72.4 cm)

2” (5.1 cm) Min.

Note: Install the

oven only with specific models listed on the label located on top of the oven.

Single Oven Cutout for Installation Between a Monogram Advantium Oven and a Monogram Warming Drawer

23 1/2”

(59.7 cm)

Min.

Inside

Per Advantium Requirement

2” (5.1 cm) Min.

27 5/16”

45 1/4” (114.9 cm)

(69.2 cm) Max.

9 1/4” (23.5 cm)

NOTE: Additional clearances may be

required. Check to be sure the oven supports above the Warming Drawer do not obstruct the required interior 23 1/2”

(59.7 cm) depth and 9 1/4” (23.5 cm) height. The middle rail separating the openings may need to be larger than the 2” (5.1 cm) minimum shown. Always refer to the individual installation instructions packed with each product for specific requirements.

Warming Drawer Combined with Advantium and Single Oven:

Install a separate 120V, 60Hz, properly grounded receptacle. See installation Instructions packed with each product for specific requirements.

28 1/2” (72.4 cm)

2” (5.1 cm) Min.

1” (2.5 cm) Min. Above Toekick

Page 10

Installation Instructions

Electrical Connections

ATTENTION INSTALLER

All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products.

DO NOT shorten the flexible conduit. The conduit strain relief clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not fit within the clamp, do not install the oven until a clamp of the proper size is obtained.

NOTE TO ELECTRICIAN: The 3 power leads supplied with this appliance are UL recognized for connection to heavier gauge household wiring. The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of household wiring. The current carrying capacity of the conductor is governed by the wire gauge and the temperature rating of the insulation around the wire.

WARNING: Improper

connection of aluminum house

wiring to copper leads can result in an electrical hazard or fire. Use only connectors designed for joining copper to aluminum and follow the manufacturer’s recommended procedure closely.

Turn off the circuit breaker or remove fuses to the oven branch circuit.

With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below. Position the conduit in such a manner that it will lie on top of the oven in a natural loop when the oven is installed. You will need to purchase an appropriate strain relief clamp to complete the connection of the conduit to the junction box.

Conduit 48 1/2” (123 cm) long

Place oven on a support to assist in connecting conduit

Junction Box Location

5”

(12.7cm)

BARE

GROUND

Strain Relief Clamp (not included) must be used at Junction Box

RED

WHITE

BLACK

GROUND

WIRE

AVERTISSEMENT :

Le raccordement inadéquat d’un

câblage résidentiel en aluminium à des fils de sortie en cuivre peut entraîner un risque électrique ou d’incendie. Utilisez uniquement des connecteurs conçus pour raccorder du cuivre à l’aluminium et respectez minutieusement la procédure recommandée par le fabricant.

(Continued on following page)

Page 11

Installation Instructions

Electrical Connections cont.

New Construction and Four-Conductor Branch Circuit Connection

• When installing in new construction, or

• When installing in a mobile home, or

• When installing in a recreational vehicle, or

• When local codes do not permit grounding through

neutral:

a. Cut the neutral (white) lead from the crimp.

Re-strip the neutral (white) lead to expose the proper length of conductor.

Ground Wire

Junction Box Cover

b. Attach the appliance grounding lead (green or

bare copper) in accordance with local codes. If the residence grounding conductor is aluminum, see WARNING on page 10.

This oven is supplied with a 48” (123 cm) long flexible conduit consisting of:

3 insulated conductors (copper) 1 bare ground conductor (copper)

Attach conductors to residence wiring as

shown by wiring diagram.

CONDUIT

FROM OVEN

UL APPROVED

CONNECTOR

TO BREAKER PANEL

#12-#10 AWG COPPER NMD90 WIRE. FUSE 20

AMP CIRCUIT BREAKER

BLACK 16AWG

BARE

COPPER

16AWG

BLACK

GROUND

UL APPROVED

JUNCTION BOX AND COVER

RED

16AWG

WHITE

(NEUTRAL)

16AWG

RED

WHITE

Three-Conductor Branch Circuit Connection

When connecting to a three-conductor branch circuit, if local codes permit:

a. Connect the bare oven ground conductor with the

crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.

c. Connect the oven neutral (white) lead to

the branch circuit neutral (white or gray) in accordance with local codes, using a wire nut.

d. Connect the oven red lead to the branch circuit

red lead and the oven black lead to the branch circuit black lead in accordance with local codes, using wire nuts. If the residence red, black or white leads are aluminum conductors, see WARNING on page 10.

e. Install Junction Box Cover.

Ground and Neutral Wires

Junction Box Cover

b. Connect the oven red lead to the branch circuit

red lead in accordance with local codes, using a wire nut.

c. Connect the oven black lead to the branch circuit

black lead in accordance with local codes, using a wire nut. If the residence red, black or white leads are aluminum conductors, see WARNING on page 10.

d. Install Junction Box Cover.

Page 12

Installation Instructions

Securing the Oven in the Opening

C1 C2

Sliding the Oven Into the Opening

a. Loop (do not tie) a 36” (91 cm) string

around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven.

a. Drill through the mounting holes (top and

Pull out on string loop while pushing the oven into the cabinet

b. Lift oven into cabinet cutout using the oven

opening as a grip. Carefully push against oven front frame. Do not push against outside edges.

c. As you slide the oven back, pull the string

so that the conduit will lie on top of the oven in a natural loop.

Drilling the Pilot Holes and Mounting the Oven

NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.

bottom) of the side trim, for the #8 screws provided.

The screws must

Mounting

Hole

Locations

WARNING:

screws must be used. Failure to

do so could result in the oven falling out of the cabinet causing serious injury.

be a minimum of 1/4” (0.64 cm) from the front of the cutout.

Mounting

d. When you are sure the conduit is out of the

way, slide the oven 3/4 way back into the opening. Remove the string by pulling on one end of the loop.

AVERTISSEMENT :

Des vis de montage doivent

être utilisées. Le défaut de se conformer à cette directive peut occasionner la chute de four et, par voie de conséquence, des blessures sévères.

b. Secure the oven to cabinet with screws

provided.

NOTE: If the cabinet is particle board, you must use #8 x 3/4” (1.9 cm) particle board screws. These may be purchased at any hardware store.

(Continued on following page)

Page 13

Installation Instructions

Installing the Oven Rack Supports and Oven Racks

Oven Rack Supports

Place the rack support with the slotted holes over the rear bolts and the round holes over the front bolts. Using an adjustable wrench, lightly secure with four nuts but do not overtighten or the enamel could be chipped. Repeat for the second rack support.

Slotted holes over rear bolts

Oven Racks

Round holes over front bolts

Installing the Metal Bottom Trim

a. Place the bottom trim between the side

trim and against the bottom of the cutout.

b. Using two trim screws provided, secure

the bottom trim to the bottom edge of the cabinet.

a. Place the rear rack locks over and onto

the rack supports (five rack positions are available, including the top position).

b. Slide the rack all the way in until the rear

rack locks are secure on the rear rack supports, and press the front rack locks onto the front rack supports.

Slide the rack all the way in and push down to lock the front rack locks onto the front rack supports

IMPORTANT: If this unit is ever removed from the cabinet or the oven is ever pulled out for service, the trim must be removed first or damage to the trim will occur.

Page 14

Installation Instructions

Replacing the Oven Door

NOTE: may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle.

The oven door is heavy. You

Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.

Open the oven door as far as it will open.

Push the hinge locks up against the front frame of the oven cavity, to the locked position.

Hinge in Locked Position

Notch of Hinge Securely Fitted into Bottom of Hinge Slot

Close the oven door.

With the door at the same angle as

the removal position, seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be fully seated into the bottom of the slot.

Hinge Arm

Bottom Edge of Slot

Hinge Notch

Page 15

Installation Instructions

Pre-Test Checklist

Remove all protective film, if present, and any stickers.

Check to be sure that all wiring is secure and not pinched or in contact with moving parts.

NOTE TO ELECTRICIAN: You must unplug the green wire (near where the long flexible conduit exits the unit) when conducting high-potential testing. Please replug prior to operation.

Operation Checklist

Remove all items from the inside of the oven.

Check that conduit is securely connected to the junction box.

Turn on the power to the oven. (Refer to your Owner’s Manual.) Verify that the bake and broil units, and all cooking functions operate properly.

Check that the circuit breaker is not tripped nor the house fuse blown.

Check that the bottom trim is installed properly (see page 13).

Check to be sure the mounting screws are installed and flush with the side trim (see page 12).

NOTE TO ELECTRICIAN: The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring. The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring. The current carrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire.

NOTE: ALUMINUM WIRING

See your Owner’s Manual for troubleshooting list.

If "bAd" "LInE" appears in the display when the power is turned on, the house wiring connections are incorrect.

A. WARNING: IMPROPER

CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN AN ELECTRICAL HAZARD OR FIRE.

B. Splice copper wires to aluminum

wiring using special connectors designed and UL approved for joining copper to aluminum, and follow the manufacturer’s recommended connector procedure closely.

NOTE: Wire used, location and enclosure of splices, etc., must conform to good wiring practice and local codes.

Page 16

Printed in U.S.A.