GE ZDP36L6DSS User Manual

For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.

Monogram.

™

Specification Created 7/01

ZDP36L6DSS - GE Monogram 36" Professional Range with 6 Burners

Dimensions and Specifications (in inches)

These ranges are factory set for either natural gas or
liquid propane gas.

36" Natural Gas Model:

ZDP36N6WSS–6 gas burners

36" Liquid Propane Gas Model:

ZDP36L6WSS–6 gas burners, grill and griddle

Accessory Requirements:

All models require the installation of a backguard. A
backguard should be ordered at the same time as the
range. Both must be on site at the time of installation.

Order one backguard for 36" models:

ZX1B36WSS–1-1/2" high backguard
(required for island installations)
ZX12B36WSS–12" high backguard
ZX22B36WSS–22" high backguard with warming rack
(2 piece)

Important!
Please call for your exclusive
40-Point Inspection! 800.444.1845

Owners of Monogram™professional ranges enjoy the
additional benefit of a complimentary visit by a specially
trained technician. This includes temperature calibration
of each oven and cooktop element. This is Monogram’s
way of ensuring correct installation and precise operation
of your new professional range.
Our Preferred Service Specialists are always at
your service.

21-1/4"

12"

1-1/2"

35-1/4"-36-3/4"

28-1/4"

35-7/8"

Available Backguards

ZX22B36WSS

ZX12B36WSS

ZX1B36WSS

R

Listed by
Underwriters
Laboratories

For answers to your Monogram,® GE Profile™or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center®service, 800.626.2000.

Monogram.

™

Specification Created 7/01

ZDP36L6DSS - GE Monogram 36" Professional Range with 6 Burners

Dimensions and Specifications (in inches)

Advance Planning:

Refer to dimensional drawings for appropriate placement
and necessary clearances when planning
the installation.

• Cabinetry cannot be installed directly above the range.

• This range requires the installation of a vent hood,

30" to 36" above the surface.

– The vent hood must be at least 24" deep.
– The vent hood must be the same width as the range.
– The vent hood must provide at least 600 CFM and

up to 800 CFM.
– When installing a range that includes a grill, select a
blower on the high end of the CFM recommendation.

• Working areas adjacent to the range should have
18" minimum clearance between countertop and cabinet
bottom.

• Clearance between range and side wall or combustible
material must be at least 12" on each side.

If the range is installed in an island:

• Allow 12" min. clearance at the back to combustible

materials.

• Allow 36" min. above the cooking surface to
combustible materials.

• The vent hood must provide at least 600 CFM and
up to 1200 CFM.

• Installation must conform with local codes. In the
absence of local codes, the range must comply with
the National Fuel Gas Code, ANSI Z223.1-1990.

A.G.A. approved

Installation Information:

Before installing, consult installation instructions
(Pub. #49-8786) packed with product for current
dimensional data.

3/-1/4"

18" Min.

4"

35-3/8" Max. for Counter Level
36-3/4" Max. with Range Leveling Legs Fully Extended

3/-1/2"

Gas Supply

Electrical Supply

Cooking Surface

13"

Max.

4"

12"

36" Wide Range Hood

12" Min. to
Combustible
Material
Each Side

36" Min. to
Combustible
Material From
Cooking Surface

12"

Low Back

High
Shelf

29-1/16"

12"

3-1/4"

21-1/4"

12"

36" Min.

to Combustibles

28-1/4"

31-1/2"

45-5/8"

0" Clearance

Island Trim

1-1/2"

36" Min.

to Combustibles

0" Clearance

12" Min. to Combustibles
Without Backguard

R

Listed by
Underwriters
Laboratories