GE ZDIC150WBB, ZDIC150WBBA, ZDIC150WBBB, ZDIC150WSSA, ZDIC150WWW Installation Guide

...
i
stoll rio
i
Automotic Icemaker
ZDIC150 ZDIS150
Design Guide
structio
$
monogram.corn
Installation Instructions
BEFORE YOU BEGIN:
Read these instructions completely and carefully.
IMPORTANT:
Save these instructions for local inspector's use.
IMPORTANT:
Observe all governing codes and ordinances. Note to Installer - Be sure to leave these
instructions with the Consumer. Note to Consumer - Keep these instructions
with gour Owner's Manual for future reference.
WARNING:
This appliance must be properlg grounded.
Failure to do so can result in death, fire or
electrical shock. See"Power Supplg," page 5.
AVERTISSEMENT :
Cet appareil dolt _tre correctement mis _ la terre. Le non-respect de ces
instructions peut causer la mort, un incendie ou un choc _lectrique. Consulter
<<Alimentation 61ectrique >>,page 5.
CONTENTS
Design Information
Models Available ....................................................................]
Cutout & Product Dimensions ..........................................]
Optional Accessories ............................................................3
Tools and Materials Required ........................................3
Installation
Advance Planning ..................................................................4
Power Supply ..........................................................................5
Remove Packaging ................................................................5
Adjust Height of Icemaker ................................................5
Water Supply ..........................................................................6
Connect the Drain ..................................................................6
Connect Water Supply ........................................................7
Reverse Door Swing ........................................................7, 8
Accessories
ZIP75WW, ZIP75BB Kit for 3/4" thick panels ....9, i0
ZTBSS1 Tubular Handle Kit ............................................11
If gou received a damaged icemaker, gou should
immediatelg contact gour dealer or builder,
Proper installation is the responsibilitg of the installer. Product failure due to improper installation is not covered under the GE Appliance Warrantg. See the Owner's Manual for warrantg information.
Use this appliance onlg for its intended purpose. Check with local utilities for electrical codes that
applg in gour area. Local codes varg. Installation, electrical connections and grounding must complg with applicable codes. In the absence of local codes,
the icemaker should be installed in accordance with
National Electrical Code ANSI/NFPA 70-1990 or latest edition.
For Monogram local service in gour area, call
1.800.444.1845. For Monogram Service in Canada, call
1.800.561.3344. For Monogram Parts and Accessories, call
1.800.626.2002.
Design Information
MODELS AVAILABLE
ZDIC!50, ZDIS!50 The icemaker nag be installed below a countertop Available in black, white and stainless steel, or used free-standing,
CUTOUT & PRODUCT DIMENSIONS
_'nI J" The installation of a 3/4" thick
'-t._\k/ custom panel will require an
L addtona 1-1/2"wdef er
strip on the hinge side.
"16-1/2" with a 3/4" thick
custom panel
23-5/16" to
34" rain.
Adjustable
to 34-1/2"
Cutout dimensions shown allow for a full door swing. Additional Clearances:
The installation of a 3//4" thick custom panel will require an additional 1-1/2" wide filler strip on the
hinge side. The filler strip will act as a spacer between the icemaker case and an adjacent
cabinet. The filler strip will prevent interference with the icemaker door swing when it is installed
between frameless or framed cabinetrg. The width of the opening must
include the filler strip.
NOTE: The addition of a 3/4" thick front panel
will result in a front to back depth of 24-1/16."
The product cannot be installed flush to
adjacent 24" deep cabinets with a
3/4" thick custom panel.
Factorg set ", \ - for 110°door ",,, swing, Allow 2" ',,
rain to wall for 1102 ",_"_, 90° door swing _t
I
i
5-1/2" Minimum
to Wall
OPTIONAL ACCESSORIES
ZIP75WW White and ZIP75BB Black--For the installation of a trimless 3/4" thick custom panel
on white and black models (not for stainless steel models). This kit provides a handle that can be
installed with the custom panel. A custom handle of gour choice may be installed onto the 3/4" panel. See installation instructions on pages 9 and !0.
TOOLS AND MATERIALS REQUIRED
1//4" socket
3//4" adjustable wrench
Level GESmartConnecf" Refrigerator Tubing Kit or 1/4" O.D.
copper tubing, of sufficient length to reach the installation
ZTBSSl--Monogram tubular stainless steel handle for 3/4" thick custom panels. Order this kit from gour
Monogram supplier,
ZPK1--Drain Pump Kit. For use when a floor drain is not available. The drain pump must be installed inside the unit and can operate at a maximum vertical height of !0 feet. !0 feet of tubing is supplied with
the kit.
Installation Instructions
ADVANCE PLANNING
CAUTION: Duetoexcessive
weight, TWO PEOPLEARE REQUIRED TO MOVE AND INSTALL THIS ICEMAKER.
Failure to do so can result in back or other injurg.
MISE EN GARDE :
A cause de son poids _lev_; IL FAUT DEU× PERSONNES POUR DEPLACER
ET INSTALLER CETTE MACHINE GLA_ONS. Le non-respect de ces
instructions peut causer des blessures au dos ou d'autre nature.
WATER SUPPLY A cold water supplg with water pressure of between
30 and 120 psi is required to operate the icemaker,
If gou have questions about gour water pressure,
call a licensed, qualified plumber. REVERSEOSMOSIS WATER SUPPLY
IMPORTANT; The performance of the icemaker
mag be affected when it is connected to a reverse osmosis sgstem,
The pressure of the water supplg coming out of a reverse osmosis sgstem going to the water inlet
valve of the icemaker needs to be between 30 and
!20 psk
If a reverse osmosis water filtration sgstem is connected to gour cold water supplg, the water pressure to the reverse osmosis sgstem needs to be a minimum of/40 to 60 psi. The reverse osmosis sgstem must provide ! gak of water per hour to
the icemaker for proper icemaker operation.
Do not use copper tubing when the icemaker is connected to a reverse osmosis water sgstem.
Choose the location:
ADVANCE PLANNING (cont.)
Before gou begin:
1. If a custom panel is to be installed, follow the instructions shown on pages 9 and 10.
-Order ZIP7S (black or white) panel kit.
-Order the custom panel from the cabinet
manufacturer.
-Secure the custom panel onto the icemaker.
2. Determine a method of drainage. If a floor drain is to be installed, the drain must be accuratelg located. The installation of a custom door panel will affect the drain location. See page 6 to
determine the exact location of the floor drain, front to back, with or without a custom door
panel.
-A drain pump kit, ZPK1, is available and will not
interfere with placement of the icemaker.
3. The door swing is reversible. If desired, change the door swing before installation.
4. Slide the icemaker into the installation location,
-Open and close the door to be sure there is no
interference.
-Check to be sure the icemaker can be moved
back into the opening, flush with adjacent
cabinetrg. There should be no interference with the floor drain.
-Check to be sure the icemaker is level. The
icemaker will not operate properlg if it is not level. See page 5.
Not designed for outdoor installation. The icemaker must be installed in an area protected from elements such as wind, rain, water
sprag or drip. The area should be ventilated with temperatures above 55°F (!3°C) and below !!0°F
(/43°C).Best results are obtained between 70°F (21°C)and 90°F (32°C).
The icemaker mag be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper operation,
-Installation should be such that the icemaker can be moved forward for servicing, if necessarg,
-The bottom grille on the front must be unobstructed to provide proper air flow.
Loading...
+ 8 hidden pages