Installation
Instructions
Automatic Icemaker
ZDI15
ZDIS15
Design Guide with
Installation Instructions
Monogram:_
Installation Instructions
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT- Save these instructions for
local inspector's use.
• IMPORTANT- Observe all governing codes
and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions
with your Owner's Manual for future reference.
WARNING:
This appliance must be properly grounded.
See "Power Supply", page 4.
AVERTISSEMENT :
Get appareil doit _tre correctement mis
la terre. Consulter _{Alimentation
_lectrique _, page 4.
CONTENTS
Design Information
Models Available ..............................................................3
Cutout & Product Dimensions ........................................3
Optional Accessories ......................................................3
Tools and Materials Required ......................................3
Installation
Advance Planning ............................................................4
Power Supply ....................................................................4
Remove Packaging ..........................................................5
Adjust Height of Ice Machine ........................................5
Water Supply ....................................................................6
Connect the Drain ............................................................6
Connect Water Supply ....................................................7
Reverse Door Swing ....................................................7, 8
Accessories
ZIP75WW, ZIP75BB Kit for 3/4" thick panels ........9, 10
If you received a damaged ice machine, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GEAppliance Warranty. See the
Owner's Manual for warranty information.
• Use this appliance only for its intended purpose.
Check with local utilities for electrical codes that apply
in your area. Local codes vary. Installation, electrical
connections and grounding must comply with
applicable codes. In the absence of local codes, the
ice machine should be installed in accordance with
National Electrical Code ANSl/NFPA 70-1990 or latest
edition.
For Monogram local service inyour area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.888.880.3030.
For Monogram Parts and Accessories, call
1.800.626.2002.
MODELS AVAILABLE
Design Information
ZDI15, ZDIS15
Available in black, white and stainless steel.
CUTOUT & PRODUCT DIMENSIONS
34" min.
Adjustable
to 34-1/2"
23-5/16" to
14-13/16'
The ice machine may be installed below a countertop
or used free-standing.
Cutout dimensions shown allow for a full door swing.
When installing a 3/4"thick custom door panel,
additional clearances atthe sides may be required.
Frameless Cabinets:
• If installing between frameless cabinets, a 1/2" filler
strip or side panel may be required on the hinge side.
The filler strip will act as a spacer between the door
case and adjacent cabinet, and will prevent
interference with icemaker door swing. The width of
the opening must include filler or side panel thickness.
NOTE: The addition of a 3/4" thick front panel will result
in a front to back depth of 24-1/16."
OPTIONAL ACCESSORIES
ZIP75WW White and ZIP75BB Black--For the
installation of atrimless 3/4" thick custom panel on
white and black models (not for stainless steel models).
A custom handle of your choice may be installed
onto the 3/4" panel. See installation instructions on
pages 9 and 10.
TOOLS AND MATERIALS REQUIRED
• 1/4" socket
• 3/4" adjustable wrench
•Level
• GE SmartConnectTM Refrigerator Tubing Kit or 1/4" O.D.
copper tubing, of sufficient length to reach the installation
ZPK1--Drain Pump Kit. For use when a floor drain is
not available.
3
Installation Instructions
ADVANCE PLANNING
weight, TWO PEOPLEARE REQUIRED TO
CAUTION: Duetoexcessive
MOVE AND INSTALL THIS ICE MACHINE.
MISE EN GARDE :
A cause de son poids elev&lL FAUT
DEUX PERSONNES POUR DEPLACER ET
INSTALLERCEDISTRIBUTEUR DE GLACE.
Choose the location:
• The ice machine must be installed in an area
protected from elements such as wind, rain, water
spray or drip. The area should be ventilated with
temperatures above 55°F (13°C) and below 110°F
(43°C). Best results are obtained between 70°F (21°C)
and 90°F (32°C).
• The ice machine may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper operation.
-Installation should be such thatthe ice machine
can be moved forward for servicing, if necessary.
-The bottom grille on the front must be unobstructed
to provide proper air flow.
Before you begin:
1. If a custom panel is to be installed, follow the
instructions shown on pages 9 and 10.
-Order ZIP75 (black or white) panel kit.
-Order the custom panel from the cabinet
manufacturer.
-Secure the custom panel onto the ice machine.
2. Determine a method of drainage. If a floor drain is
to be installed, the drain must be accurately
located. The installation of a custom door panel will
affect the drain location. See page 6 to determine
the exact location of the floor drain, front to back,
with or without a custom door panel.
-A drain pump kit, ZPK1, is available and will not
interfere with placement of the ice machine.
3. The door swing is reversible. If desired, change the
door swing before installation.
4. Slide the ice machine into the installation location.
-Open and close the door to be sure there is no
interference.
-Check to be sure the ice machine can be
moved back into the opening, flush with adjacent
cabinetry. There should be no interference with
the floor drain.
POWER SUPPLY
IMPORTANT: (Please read carefully).
FORPERSONAL SAFETY,THIS APPLIANCE MUST BE
PROPERLYGROUNDED.
Do not use an extension cord or adapter plug with
this appliance. Follow National Electrical Code or
prevailing local codes and ordinances.
This ice machine must be supplied with 115V,60Hz,
and connected to an individual, properly grounded
branch circuit, and protected by a 15 or 20 amp circuit
breaker or time delay fuse.
Electrical Supply Should
Enter From Back Wall
InShaded Area.
• A properly grounded 3-prong receptacle should be
located within reach of the ice machine's 66" long
power cord. For a built-in installation, locate the
receptacle in the shaded area shown.
IMPORTANT: (Please read carefully).
The power cord of this appliance is
equipped with a three-prong
(grounding) plug that mates with
a standard three-prong grounding
wall receptacle to minimize the
possibility of electric shock. The
customer should have the wall receptacle and circuit
checked by a qualified electrician to make sure the
receptacle is properly grounded and has the correct
polarity.
• Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with
a properly grounded three-prong wall receptacle.
Do not,under any circumstances, cut or remove
the third (ground) prong from the power cord.
DO NOT USEAN EXTENSION CORD.
4
Installation Instructions
REMOVE PACKAGING AND PARTS
• Laythe carton on rear face
and break open the bottom
flap.
• Setthe carton upright
with all four bottom flaps
outward.
• Lift carton up and off
icemaker.
• Remove all tape and
packaging material from the outside and inside
of the cabinet,
• Locate parts package with plastic plug buttons.
Set aside.
Open Bottom Flaps
ADJUST HEIGHT OF ICE MACHINE
Height adjustments may be necessary to install
the ice machine below a countertop, and may be
accomplished by adjusting both the front and rear
leveling legs,
ower
To adjust the height:
• With one person holding the ice machine, carefully
tilt the machine to access the leveling legs,
• Use an adjustable wrench to turn the legs.
-Turn legs right to lower, turn left to raise the
machine,
• Check top and side with a spirit level. Continue
adjusting legs until the ice machine is level
and stable.
Installation Instructions
WATER SUPPLY
• A cold water supply is required for icemaker
operation. The water pressure must be between
20 and 120 p,s.i.
Water Supply Should
Enter From Back Wall
In Shaded Area.
• Route GE SmartConnect TM Kit or 1/4" O.D. copper
tubing between house cold water line and the water
connection location.
• The water line should be long enough to extend
to the back of the ice machine. Allow enough to
accommodate moving unit forward for service.
NOTE:The only GEapproved plastic tubing is supplied
in the GE SmartConnectTM Refrigerator Tubing kits. Do
not use any other plastic water supply line because the
line is under pressure at all times. Other types of plastic
may crack or rupture with age and cause water
damage to your home. GE SmartConnecf MRefrigerator
Tubing Kits are available in the following lengths:
2'(0,6 m) WX08X10002
6'(1.8 m) WX08X10006
15' (4,6m) WX08X10015
25' (7.6 m) WX08X10025
Shut off the main water supply
Turn on the nearest faucet long enough to clear the
line of water.
Install a shut-off valve between the ice machine
water valve and cold water pipe in a basement or
cabinet, The installation of an easily accessible
shut-off valve in the water line is required,
NOTE: Itis best to install the valve into a vertical
water pipe. If you install the valve into a horizontal
water pipe, make the connection atthe top or side,
rather than atthe bottom, to avoid drawing off any
sediment from the water pipe,
• Turn on the main water supply and flush debris
from the line. Run about a quart of water through
the tubing into a bucket, Shut off water supply at
the shut-off valve.
WATER SUPPLY (cont.)
NOTE: Saddle type shut-off valves are included in
many water supply kits, but are not recommended
for this application,
NOTE:Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consultwith your licensed plumber.
• Install optional water filter in the water line near the
ice machine. A water filter is recommended in areas
where water supply contains sand or particles.
Installation instructions are packed with the filter.
CONNECT THE DRAIN
This ice machine is
equipped with a gravity
drain to prevent water
from flowing back into
the ice machine storage
bin and potentially
flowing onto the floor.
A floor drain is
acceptable, The ideal
installation has a
standpipe with a 2" to
1-1/2" PVCdrain reducer
installed directly below
the outlet of the drain tube:
-7-1/2" to centerline _
of the opening,
3-1/2" high.
-Approximately _j
-22" from the front,
or 22-3/4"when _5,, _ 7-t/2"-_:L_
installing a 3/4" LocateStalldpipein exact
door panel,
• Drain lines must be at least 5/8" inside diameter.
NOTE:A drain pump is necessary when a floor drain
is not available, Order ZPK1 Drain Pump Kit or contact
your local plumber for a recommended pump available
in your area.
TEST DRAIN HOSE ALIGNMENT: Before sliding the ice
machine into the cabinet opening, check to be sure
the bottom of the drain tube is below the rear cover.
Totest, place a pan belowthe drain hose. Pour a
gallon of water into the ice bin and checkto be sure
that water does not wet the rear cover.
Custom Panel
3q/2"
Centerof TheCutout
/Drain Hose
Installation Instructions
CONNECT WATER SUPPLY
• The water line should be flushed to clear any foreign
material before connecting to the icemaker.
• Connect the water line to the water supply tube
outside of the rear access cover.
Water
Supply
Line
CopperTubing:
• Use a standard plumbing female connector or union
for 1/4" copper tubing that can be purchased locally.
Coupling
(NotSupplied)
Nut
(Supplied)
\
Ferrule
Lineto
Icemaker
GE SmartConnectTM Tubing:
• Insert the molded end ofthe tubing into the icemaker
connection. _ghten the compression nut until it is
just hand tight.
• Tighten one additional turn with a wrench,
Overtightening can cause leaks!
• Make sure there are no sharp bends or kinks that
could restrict water flow.
• Slide the ice machine into its permanent location.
• To prevent
rattling, be sure
the copper tubing
does not touch
the side wall or
other parts inside
the cabinet.
• Open the shut-off
valve. Check for
leaks. -lighten
any connections
(including
connections
atthe valve)
if necessary.
(NotSupplied)
Water Pan
Water Valve -
5-11/16" 4-5/8"
\
Nut
(Supplied)
REVERSE THE DOOR SWING
IMPORTANT: Disconnect power to
the ice machine.
Tools Required:
• 1/4" and 5/16"wrench
• Flat putty knife
• Phillips screwdriver
Parts Supplied:
• 4 plug buttons
• 4 hinge screws
(on some models)
Parts Identification: (For Reference 0nly)
Hinge Pin Handle Screw
5/16" Hex Head Endcap Screw
Hinge Screw
• Remove the handle screws and lift off handle.
(On black and white models only.)
• Remove the hinge pin from the top hinge.
• Lift the door off of the bottom hinge. Place the hinge
pin back into the top hinge.
Reverse the door endcaps:
• Remove the screws and endcaps from the door,
top and bottom.
• Place the top endcap onto the bottom of the opposite
side of the door with the longflat side facing the
door front.
• Place the bottom endcap onto the top of the opposite
side of the door, with the longflat side facing the
door front.
• Setthe door aside.
Installation Instructions
REVERSE THE DOOR SWING (cont.)
Reverse the hinges:
• Using a flat putty knife, remove the screw hole plugs
opposite the door hinges, top and bottom. Set aside.
• Remove the two screws holding top hinge.
• Turn the hinge upside down, with the hinge pin
pointing up. Reinstall the hinge on the opposite side
at the bottom of the door.
• Remove the bottom hinge. Turn the hinge upside
down and install on the opposite side atthe top.
• Push screw hole plug buttons (supplied) into the
original screw holes.
• Remove the top hinge pin.
• Place plastic hinge sleeve on the bottom hinge and
position the door onto the pin.
• Place plastic hinge sleeve in the top hinge hole on
the door. Align the door on the bottom hinge and
replace top hinge pin.
• Reinstall handle with original screws.
Top Hinge _ HingePin
HingeSleeve/
DoorStop
T
REVERSE THE DOOR SWING (cont.)
To reverse the door catch:
• Remove the plastic screws
from the opposite side
of the door.
• Remove the metal screws
from the magnetic door
catch and reinstall on the
opposite side of the door.
• Install the plastic screw
into place on the opposite
side of the door.
Reverse
Door Catch
Position
BottomHinge
Hex Head Hinge Screw
, Hex Head
Hinge Screw
Sleeve/
_'-- Hinge Pin
Top
BottomHinge
8
Installation Instructions for ZIP75WW, ZIP75BB Kit
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT- Save these instructions for
local inspector's use.
• IMPORTANT- Observe all governing codes
and ordinances.
• Note to Installer- Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner's Manual for future reference.
WARNING:
To prevent electric shock, disconnect
electrical power supply to ice machine
before installing front panel. Do not operate
ice machine while installing panel.
AVERTISSEMENT :
Pour _viter les chocs _lectriques, il faut
debrancher I'alimentation du distibuteur
de glace avant d'installer le panneau avant.
Le distributeur de glace ne dolt pas _tre
en marche pendant I'installation du
panneau avant.
Kit Contents:
• 2 side trim pieces
• 8 side trim screws
• Door handle
This kit contains a new handle and 2side mounting
brackets to support a trimless custom door panel
up to 3/4"thick. A custom handle may replace the
supplied handle.
IMPORTANT:
• Cut edges of the custom door panel will be seen and
must be finished for best appearance. The back side
of the panel should be finished a minimum of 1/2"
on all sides.
• The custom panel, both raised and flat design,
should be constructed in the same manner as typical
cabinet doors.
• Order the custom panel from the cabinet manufacturer.
Be sure to provide the exact dimensions so that the
panel is constructed accurately.
Left Trim
29-1/2" I
Custom
Panel
Right Trim
Tools and Materials Required:
• 8 flat head wood screws, 1/2" long
• Drill and 1/8" bit
• Safety glasses
• Tape
• Custom panel
NOTE: If installing a 3/4" trimless custom panel, a
3/4"wide filler strip or side panel may be required.
The filler strip will act as a spacer between the
icemaker case and the adjacent cabinet, and will
prevent interference with the icemaker door swing.
The width of the cutout opening must include the
additional width of the filler panels.
14_23/32"
Installation Instructions for ZIP75WW, ZIP75BB Kit
I STEP 1 DISCONNECT POWER I
STEP 2 REMOVE HANDLE
• Remove the door handle by removing the two top
mounting screws. Set screws aside, Discard handle.
• The Monogram nameplate is held in place with
adhesive. Remove the nameplate.
STEP 3 MARK MOUNTING
• Align and hold the side trim pieces againstthe ice
machine door and mark screw locations on the sides.
• Drill 1/8" pilot holes into the door sides of the ice
machine.
STEP 4 SECURE CUSTOM HANDLE
A custom handle can be installed onto the 3/4"thick
panel, replacing the supplied handle.
• The custom handle can be installed atthe top or side
of the panel.
• Drill pilot holes through the front of the custom panel
to match the chosen handle.
TO THE ICE MACHINE
AND NAMEPLATE
SCREW LOCATIONS
TO CUSTOM PANEL.
(SKIP THIS STEP IF
YOU ARE USING THE
SUPPLIED HANDLE)
STEP 5 SECURE SIDE TRIM PIECES
TO CUSTOM PANEL
• Lay the custom panel appearance-side-down
on a clean surface.
• Align top and bottom side trim to the custom
panel sides.
• Tape the side trim pieces to the back of the
custom panel,
• Place the panel with trim against the door to be sure
that trim and panel fits the door side to side and top
to bottom. Adjust as needed.
• Mark screw locations and remove trim.
Drill pilot holes.
• Install side trim to the back side of the custom
panel with screws (not supplied). Use flat head
wood screws approximately 1/2" long,
STEP 6 INSTALL ASSEMBLED PANEL
ONTO THE ICE MACHINE
• Install panel to ice machine with supplied screws,
4 on each side.
STEP 7 INSTALL SUPPLIED DOOR
HANDLE (IF USED)
• Install the new supplied handle with original screws.
• Secure the handle to the panel with flat head wood
screws.
• Replace original handle screws in the top of the door
frame,
10
Notes
11
NOTE:While performing installations described in this book,
safety glasses or goggles should be worn.
For Monog'ram local service i)_ )our (m_a, c(dl
1.600.4dd. l,_4).
NOTE: t ro(lucl improv(_m(_m is a comimfillg (md(_avor
al G( neral El(_ctri(. Th(r(for(_, malerials, appearan(:(
and sp(_(ifi(alions ar(_ sul_je(:t to (h_mg¢ wilholll noli((.
o 6)
Pub.No.49-60016-3 ]
PartNo.197D2522PO01
2217279Rev.1 02-04JR
Printedinthe UnitedStates
Monogram;
J
GEConsumer & Industrial
Louisville, KY40225
@2004GE Company
Loading...