GE ZDBI240WBII, ZDBI240WIIA, ZDBR240PBBS, ZDWI240WBII, ZDWI240WIIA Installation Guide

Design Guide with

Installation

Instructions

Wine Chiller, Wine Reserve

and Beverage Center

monogram.corn

Safety Information

BEFORE YOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT - Savetheseinstructions

for local inspector's use.

IMPORTANT - Observe all governing codes

and ordinances.

Note to Installer - Be sure to leave these

instructions with the Consumer.

Note to Consumer - Keepthese instructions with

your Owner's Manual for future reference.

WARNING - Thisappliance mustbeproperly

grounded. See page 4,

AVERTISSEMENT -

Cet oppareil doit _tre correctement mis (_la terre.
Consultez page 4.

If you received a damaged wine chiller, wine reserve
or beverage center, you should immediately contact your

dealer or builder.

Skill Level -Installation requires basic mechanical

skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.

WARNINGS:

• Use this appliance only for its intended purpose.

• Immediately repair or replace electrical service cords
that become frayed or damaged.

• Unplug the unit before cleaning or making repairs.

• Repairs should be made by o qualified service
technician.

AVERTISSEMENT:

• II ne faut utiliser cet appareil que pour l'usoge pour
lequel il o _t_ construit.

• IIfout r_porer ou remplocer imm_diotement tout
cordon d'ulimentation _lectrique effiloch_ ou
endommog&

• D_bruncher le bar ou le r_frig_ruteur o vin ovont
le nettoyage ou toute intervention.

• Les r_porotions doivent _tre fakes par un technicien
quolifi&

For Monogram local service in gour area, call

1.800.444.1845

For Monogram service in Canada, call

1.800.561.3344

For Monogram Parts and Accessories, call

1.800.626.2002.

www.monogram.com

CONTENTS

Design Guide

The Installation Space .............................3

Product Clearances ...................................3

Side-by-Side Installation ........................3

Installation Instructions

Tools, Hardware ..........................................4

Grounding the Product ............................4

Staining Wood Drawer Fronts ..............4

Installing the Custom Frame Panel ...4

Step 1 Remove Packaging ....................4

Step 2, Reverse Door Swing ..................5

Step 3, Leveling ...........................................6

Step 4, Connect Power ............................6

Step 5, Slide Product into Cutout ........6

Step 6, Install Nameplate .......................6

Step 7, SetTemperature Controls ......6

Custom Frame Panel Models ...............6

ZTBSS1Honogram

Tubular Handle Kit.....................................7

Template for Nameplate _ Back Cover

Design Guide

THE INSTALLATION SPACE

34-1/2"-35"

24-1/8" Framed Models

Min.

NOTE:
Handle
and handle

standoff depth
is 1-3/4"

The cutout depth should be 24"
The cutout dimensions shown allow for a full door swing

and access to the pull-out racks when installed as a
built-in in standard 24" deep cabinets.

• The wine chiller, wine reserve and beverage center
can be installed freestanding.

• If installing between frameless cabinets, a 1/2" wide
filler strip or side panel mag be needed on hinge side.
The filler strip will act as a spacer between the case
and adjacent cabinet door swing. The width
of the opening must include the filler panels.

NOTE:The door should protrude 1" begond the

surrounding cabinets. Custom framed models will

protrude 1-7/8" begond surrounding cabinet doors.

Additional Specifications

• A 120 volt 60Hz., 15 or 20amp power supplg is

required. An individual properlg grounded branch

circuit or circuit breaker is recommended. Install a

properlg grounded 3-prong electrical receptacle
recessed into the back wall as shown. Electrical must

be located on rear wall as shown. NOTE:GFI(ground

fault interrupter) is not recommended.

23-3/4"StainlessSteelModels

1_23-3/4"_

PRODUCT CLEARANCES

Thestainlesssteelwine chiller,wine reserveand beverage
center isfactorg setfor a 110°doorswing.Modelsthat accept

custom panelshavea 95°door swing.
Wheninstalled in a corner:

• Allow 4" min.clearanceonthe hingesidefor the 90°door
swingand to allowracksto slideout.

• Allow 10"minimumclearanceon the hingesidefor a full

110° door swing.(ModelsZDWI240WIIandZDBI240WIIhave

a 95°doorswing.)

NOTE:Customhandleclearancesmagvarg, dependingon
custom handle depth.

10"Minimum

toWall

90° DoorSwing

21-5/8"

[ ,

I 1

i i

I

,\

10o* ,,

1 ... \_

"95° DoorSwing on Custom Frame Models

• Thedoorswingisreversibleonallmodels.Ifdesired,changethe
doorswingbeforeinstallationorbeforeinstallingthecustomflame

panel.

Choosethe location:

• Theseproductsmagbeclosedinonthetopandthreesidesaslong
asthefrontisunobstructedforaircirculationandproperaccessto

thedooE

• Donotinstalltheseproductswherethetemperaturewillgobelow
S5°F(13°C)orabove90°F(32°C).

• Donotinstallwhereitwillbesubjecttodirectsunlight,heator
moisture.

• Theseproductsarenotdesignedto bestackedoneovertheotheE

Blackor StainlessSteelToekickOptions

• Theseproductsareshippedwitha blacktoekickinstalled.
Anoptionalstainlesssteeltoekickisalsosuppliedwitheach

product.Forshippingpurposes,thestainlesssteeltoekickis
securedto the backoftheunit.

ZTBSS1TubularHandle
ZTBSS1Monogramstainlesssteeltubularhandleisavailablefor

modelsZDWI240WIIandZDBI240WII.

L- i
1 ;

90° i

4"Minimum

1

;

1 23-5/8"
i

to Wall

SIDE-BY-SIDE INSTALLATIONS

Increase storage capacitg bg installing two Monogram
beverage centers, wine chillers or wine reserves together

Or,for a complete refreshment center, install ang two
of these units together.

• A side-bg-side installation requires at least a47-1/2"
wide opening. No trim kits required.

• Products must operate from separate, properlg
grounded receptacles.

34-1/2"-35"

Installation Instructions

TOOLS REQUIRED

• #2 Phillips screwdriver

• Adjustable wrench

PARTS SUPPLIED

• Monogram nameplate

• Hardware for changing door swing

• Optional stainless steel toekick with screws and
spacers

• Left and right side hinge covers

• Top screw hole cover

GROUNDING THE WINE CHILLER,
WINE RESERVE AND BEVERAGE

CENTER

IMPORTANT - Pleasereadcarefullg.

FOR PERSONAL SAFETY',THIS APPLIANCE MUST BE
PROPERLY'GROUNDED.

The power cord of this appliance isequipped with o
three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.

Have the wall outlet and circuit checked by a qualified
electricianto makesurethe outlet ispropedggrounded.

Where a standard 2-prong wall outlet is encountered, it
is gour personal responsibilitg and obligation to have it
replaced with a properlg grounded B-prong wall outlet.

STAINING WOOD DRAWER FRONTS

The drawer fronts are unfinished cherrg wood. During
use, oil from hands may accumulate and stain the

wood.

• The drawer fronts may be stained and sealed to
match adjacent cabinetrg. The tinted glass will make
the stained wood appear darkeE A true color match
can be seen onlg when the door is opened.

• Applg the stain and sealer according to the
manufacturer's instructions. To avoid unpleasant
odor, keep the door open to ventilate and allow
the stain/sealer to drg completelg before using
the product.

INSTALLING THE CUSTOM FRAME PANEL

Go to page 6 for custom frame panel size,depending
on gour cabinet size and style.

• Install a custom handle of gour choice or optional
ZTBSS1Tubular Handle onto the custom panel before
the panel is secured to the door.

• The custom panel should be installed before sliding
the product into the installation location.

ISTEP1] REMOVE PACKAGING

•Remove cornerblocksand foam drawerstops.

•Remove allpackingmaterial,topeand protective
plasticcoverings.

•Remove stainlesssteeltoekicktapedtotheback
oftheunit.

CAUTION: Small objects area choke hazard

for children. Remove and discord ong parts not used.

DO NOT, UNDER ANY
CIRCUMSTANCES, CUT

OR REMOVE THE THIRD
(GROUND) PRONG

FROM THE POWER CORD.

DO NOT USEAN ADAPTER PLUGTO CONNECTTHE
REFRIGERATORTO A 2-PRONG OUTLET.

DO NOT USEAN EXTENSION CORD WITH THIS
APPLIANCE.

MISE EN GARDE :Lespetitsobjets

peuvent @tronglerles enfonts. IIfoutjeter toutes les
pi@cesqui ne sont pos utilis@es.

Installation Instructions

ISTEP 2 IREVERSE DOOR SWING

SKIPTHIS STEPIF DOORSWING SUITSTHE
INSTALLATION

Parts Included:

• Top left case hinge

• Bottom left case hinge

• Left and right side decorative hinge cover

• Decorative hinge screw hole cover

• Torx ® driver bit

Install

3 Hinge i _

Screws i

Remove

Top Hinge

Tools Required:

• Phillips screwdriver

• Electric drill

Remove the door:

• Flatten the shipping carton to use as a pad.

• Remove the 2 screws and the toekick. Set aside the
screws and toekick for final installation.

• Use the supplied Torx® bit and electric drill to remove
the 3 screws holding the top case hinge. Lift off the

hinge.(Screwswill be used to install the new hinge.)

• Lift the door off the bottom case hinge.

• Remove the bottom case hinge pin and bracket.

Rotate the door:
The handle will be on the right side of the door; hinges

will be installed on the left side of the case.

• Remove the door stop and cam riser on the original

bottom right side of the door.

• Remove the fill plug on the top right side
of the door.

• Turn the door over and reinstall the fill plug on the

new left side.

Reinstall the door:

• Install the original door stop and cam riser onto the

bottom left side of the dooE

• Install the new supplied bottom case hinge pin and

bracket onto bottom left side.

• Placethe door onto the bottom case hinge.

• Install the supplied left-hand top case hinge with the
3 original screws.

• Select the hinge cover marked with an "L".

• Peel backing off the tape inside the decorative hinge
coveE InstallCovers

• Pressand snap the hinge _
cover into place. &..

• Snap the screw hole cover into _I/

place on the opposite side.
IMPORTANT:
Check to be sure screws are tight and that the door

is straight and does not sag.The door should swing
freelu.

Hinge

Pinand
Bracket

Remove

Hinge

Apply Monogram Nameplate:

• Install the Monogram nameplate. See instructions
and template on back cover,

Install Toekick

The toekick has a

cutout on the left
and right sides. 1 II _I

Remove /f_J_l _----- ] II

the plug on |
the left side L MoveFill

and ( I ', _] Plugto
reinstall on \ I,,,,,_', /_t RightSide

the right X _ _ /

side. If Uou
choose to _L __ "'_

install the -_
stainless steel toekick,

reinstall the plug on the right side of that toekick.

• Install original screws and spacers or screws and
spacers supplied with the stainless steel toekick.
Install screws through the spacer standoff, toekick

and into the base as shown.

Installation Instructions

ISTEP 31LEVEL

• Use an adjustable wrench to turn the leveling legs and
raise or lower the product.

• Adjust carefullg; the product should be level and plumb
with cabinetry, and should align with adjacent toekick
height.

TurnRightto Lower
TurnLeftto Raise

If gou skipped Step 2:

• Selectthe hinge cover marked "R"or "L",depending
on door swing.

• Peel backing off the tape inside the decorative
hinge cover. Pressand snap into position.

• Snap the screw hole cover into place on the
opposite side.

ISTEP 41CONNECT POWER

• Connect power cord plug to a properlg grounded
receptacle.

• Check to make sure power is on by opening the door
to see if interior light turns on.

ISTEP SI SLIDE PRODUCT INTO

THE CUTOUT

• Carefully, slide the unit into the opening. Be careful
not to entangle the power cord.

• Make certain that the door protrudes 1" beyond
the surrounding cabinets (1-7/8" for custom frame

models).

• Check again to be sure the unit is level.

[STEP 6] INSTALL NAMEPLATE

• Follow instructions on the back page for installation of
the Monogram nameplate.

CUSTOM FRAME PANEL MODELS

ModelZDWI240WIIand ZDBI240WlI
Thesemodelsrequirea custompanelframe surrounding

the glass.Thereare two options:the panel mug be 29-3/4"
or 30" high.A 30"panel requiresa notchcut into the bottom

of the panelto avoid interferencewith the hinges.

• Routthe backsideofthe panelto the dimensionsshown.

• A custom handle of your choice or ZTBSS1TubularHandle
must be installedbeforethe panelis mountedonto

the door.

NOTE:The 4 corners
of the routed areas

mustbe squared J

to fit the coroers/

ofthe metal / - , I\
door frame.

Option 1 Option 2

I-- 23-1/8"--

2-1/4"
wide, _

°ffhel ! ] I deep,1-1/8"wide I

°, i I

- /8 w de : / 2-1/2 at--I :3
[_ _ bottom t --

3/4" Thick Custom Pane I--I

Sack Side 2-1/4"

NOTE: Right-hand models Cutthe notch
illustrated. Cut notches I/8" deep,1/4"

for hinge clearance on the wide and 1/4"
opposite side for left-hand high
door swing.

ChooseOption1 or Option2 panelsizedependingon
cabinetry sizeor stgle.

NOTE:A solid panel that covers the door glass CANNOTbe
installed on these models.

Installthe custom panel:

• Openthedoor fully.

• Removethe gasketsurroundingthe insideofthe doorto
exposethe existingscrew holesfor the custompanel.

• Holdthecustom frame panelagainstthe door andalign
carefullg,top to bottomand sideto side.Harkscrewhole
locationsonthe backside of the panel.

• Drillpilot holesinthe back sideofthe custom panel.In
hardwood,drill 3/32" pilot holes.Insoftwood,drill 5/64" holes.

• Securethe preparedpanelto the doorusingten (10)
#8 x 5/8" screws.Drivethescrewsthrough the doorframe

and into the wood.

• Replacethe gasket.

i

m m Screws

#8x5/8"

[STEP 7] SET TEMPERATURE CONTROLS

• Thetemperature controls are preset. Refer to the
Owner's Manual for more information. Allow 24 hours

for temperature to stabilize.

GLASS

Back

÷ ÷

fDoor

Frame

/./Custom

Framed
Panel

ZTBSS1 Monogram Tubular Handle Kit

BEFOREYOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT - Savetheseinstructions

for Iocul inspector's use.

IMPORTANT - Observe oil governing codes

and ordinances.

Note to Installer - Be sure to leave these

instructions with the Consumer.

Note to Consumer- Keepthese instructions

with your Owner's Manual for future reference. This kit
provides o stainless steel tubular handle to coordinate
with other Monogram appliances.

• The tubular handle must be installed onto the 3/4" thick
portion of the custom wood panel before the panel is

secured to the doo_

INSTALL THE TUBULAR HANDLE

• Use the handle as o template to locate and mark the
exact position of the screw holes. Becareful to ovoid
interference with custom panel mounting screws.

• Draw o pencil line, top to bottom and 7/8" from the
outside edge.

• Hold the tubular handle against the appearance side,
centered on the marked line.

• Mark the screw hole locations at the center of the
handle attachment posts.

• Center punch the marked hole locations. Drill 1/4"
pilot holes from the appearance side through the
entire panel thickness.

• Use o 1/2" spade bit to drill 1/4" to 5/16" deep into
the back side of the panel. Insert washer (spacer)into

the hole.

• Install screw through the handle standoff and into the
pilot hole.

• Fasten nut onto the screw until the standoff is tight
against the panel. The screw hole on the standoff
should be pointing down toward the floor.

• Place handle attachment posts inside the standoffs.

• Use the Allen wrench to install the set screws. Tighten
handle to standoffs.

TOOLS AND MATERIALS REQUIRED

• Gloves to protect against sharp edges

• #2 Phillips screwdriver

• Drill and 1/4" bit and 1/2" spade bit

• Safety glosses

• Center punch

• Pencil

THIS KIT INCLUDES

• Tubular handle

• 2 Mounting screws

• 2 Handle standoffs

• 2 Set screws for standoffs

• 2 Nuts

• 2 Washers

• Allen Wrench

1_7/8"

::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::

24-7/32"

Custom

,Framed

Panel --

Handle
Standoff

Screw

/

30"

JTubular

Handle

Handle

Attachment

Post

Set
Screw

TEMPLATE FOR NAMEPLATE LOCATION

r

Upper Left

Cornerof
Glassif Hinge

ison Left

:4 DoorFrameSide

To position nameplate:

• Cut template along dotted line.

• Hold or tape template behind glass
door so that it isvisible from the

front side.

• Remove backing from nameplate.

• Place nameplate onto front side of
door, matching illustration on the

template.

_,j__ C_uton DottedLine

TopofBadge_y

Monogram.

DOORNAMEPLATELOCATION

_Top of GlassDoor

4:

UpperRight
Cornerof

Glassif Hiflge
ison Right

DoorFrameSide

IMPORTANT:Nameplate must
be placed on the opposite side of the

door handle.

Pub.No. 31-46122-2
Port No.197D7840PO01

12-07 JR
Printed in Slovenia

Note: While performing installations described in this book,
safety glasses or goggles should be worn.

For i'4onogram ®local service in your area, call

1.800.444.1845.

Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.

GE Consumer & Industrial
Appliances

General Electric CompQn U
Louisville, KY 40225

ge.com