GE ZBD6700, ZBD6600, ZBD6905, ZBD6900, ZBD7005 User Manual
...
Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In Dishwashers
ZBD6400, ZBD6500, ZBD6600
ZBD6700, ZBD6900, ZBD7000,
ZBD7100
Chef’s Washers
ZBD6605, ZBD6905, ZBD7005,
ZBD7105
Design Guide with
Installation Instructions
Monogram.
We bring good things to life.
®
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Save these instructions for
local inspector’s use. Observe all governing
codes and ordinances.
• Note to Installer - Be sure to leave these instructions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical and electrical skills. Proper installa-
tion is the responsibility of the installer. Product
failure due to improper installation is not covered
under the GE Appliance Warranty.
• Completion Time – 1 to 2 Hours. New installa-
tions require more time than replacement installations.
• IMPORTANT – The dishwasher MUST
be installed to allow for future removal from the
enclosure if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
FOR YOUR SAFETY
Read and observe all CAUTION and WARNINGS
shown throughout these instructions.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call
1-800-626-2002.
CONTENTS
Design Information
Product Dimensions .......................................................3
Models Available ............................................................ 3
Advance Planning .......................................................... 3
Installation Preparation
Materials You Will Need.................................................4
Tools You Will Need .......................................................4
Parts Supplied .................................................................5
Prepare Dishwasher Enclosure ..................................... 5
Drain Requirements .......................................................6
Prepare Electrical Wiring ...............................................7
Prepare Hot Water Line.................................................8
Custom Panel Dimensions
Custom Panels for ZBD6400 ......................................... 9
Custom Panels for ZBD7000, ZBD7005 ........................9
Installation Instructions
Step 1, Remove Packaging ...........................................10
Step 2, Install Leveling Legs ....................................... 10
Step 3, Remove Access Covers .................................... 10
Step 4, Install 90° Elbow...............................................10
Step 5, Install Power Cord............................................11
Step 6, Level Dishwasher ..............................................11
Step 7, Slide Dishwasher into Opening.......................11
Step 8, Connect Water Line........................................ 11
Step 9, Connect Drain Line ........................................ 12
Step 10, Connect Electrical ......................................... 12
Step 11, Position and Level Dishwasher ......................13
Step 12, Pre-Test Check List........................................ 13
Step 13, Dishwasher Wet Test ..................................... 13
Step 14, Secure Dishwasher
to Cabinet or Countertop ....................................... 14
Step 15, Install Toekick, Custom Toekick .................. 14
Step 16, Install Side Trim Strips ..................................14
Panel Installation for Models
ZBD7000 and ZBD7005............................................ 15
2
Design Information
PRODUCT DIMENSIONS
34"
Adjustable
*24"
to 35"
23-7/8"
*Dishwasher model
ZBD7000 and
Chef’s Washer
model ZBD7005
require a 3/4" thick
custom panel and
will be 24-3/4"
deep.
DISHWASHER MODELS
Traditional Built-In
ZBD6400 BB, Black - Accepts 1/4" or 3/4" custom
panels
ZBD6400 WW White - Accepts 1/4" or 3/4" custom
panels
Trim Kits for models ZBD6400
• ZPF625W (white) or ZPF625B (black) custom panel
kits, supports a 1/4" thick custom door panel.
• ZPF675W (white) or ZPF675B (black) custom panel
kits support a 3/4" thick custom door panel.
Traditional Built-In
ZBD6500 SS, Stainless steel door
Professional Series
ZBD6600 SS, Stainless Steel
Fully Wrapped
ZBD6700 BB, Black
ZBD6700 WW, White
ZBD6900 SS, Stainless steel with black controls
Fully Integrated
ZBD7000 II, Requires custom panel and handle
ZBD7100 SS, Stainless steel with tubular handle
CHEF’S WASHER MODELS
Professional Series
ZBD6605 SS, Stainless steel
Fully Wrapped
ZBD6905 SS, Stainless steel
Fully Integrated
ZBD7005 II, Requires custom panel and handle
ZBD7105 SS, Stainless steel with tubular handle
ADVANCE PLANNING
• These dishwashers are designed for versatility,
adaptable to virtually any installation.
• All models have a full length door or a modified
door to accept a full cabinet panel without the
traditional access panel
• Side tub flange trim is adjustable and will conceal
any slight gap between the dishwasher and adjacent
cabinetry.
• These dishwashers may be installed beneath
countertops of stone or other materials that will not
accept screws. No trim kit required.
Standard installation in 24" deep cabinets
• In standard 24" deep cabinets, the dishwasher door
will be flush with adjacent cabinetry.
• Models with 3/4" thick custom door panel will fit
flush with adjacent cabinetry.
Supplied or Custom Toekicks
• A 2-piece toekick is supplied with all models. The
toekick is height and depth adjustable.
• Depending on cabinetry style, a custom toekick can
also be installed to match cabinetry. Care must be
taken to assure door swing clearance above the
toekick.
• A notched continuous toekick may be necessary to
allow a long door panel, on models ZBD7000 and
ZBD7005, to swing back and under the dishwasher.
ADA-Compliant
Installation below 34" high countertops
A reduced height installation (32-1/2" min.) beneath
a 34" countertop, can be accomplished by removing
the front leveling legs. The rear legs should be
screwed in flush with the bottom support, as shipped.
The front of the dishwasher must be shimmed to
level the dishwasher. Water and electrical must be
routed through the back wall.
• All models are ADA-Compliant. Models ZBD7000
and ZBD7005 offer even more installation and
design flexibility because the required custom door
panel may be sized from 26-1/4 to 30-1/4" height.
See page 9 for details.
3
Installation Preparation
MATERIALS YOU WILL NEED:
Materials Required for All Installations
¨ 90° Elbow (3/8”NPT external thread on one end, opposite
end sized to fit water supply)
Note: Use new ferrule. Do not use old parts.
¨ Strain relief for electrical connection
¨ Thread seal tape
¨ UL Listed wire connectors (3)
¨ Screw type hose clamps
Materials For New Installations Only:
¨ Air gap for drain hose, if required
¨ Waste tee for house plumbing, if applicable
¨ Electrical cable or power cord, if applicable
¨ Hand shut-off valve (recommended)
¨ Water line 3/8” min. copper or 1/2” min. plastic (plastic
must be tested for temperature and pressure)
¨ Coupler for extending drain line, if applicable
90° Elbow
Thread Seal
Tape
Waste Tee
Air
Gap
Wire Nuts
Coupler
Shut-Off
Valve
Screw Type Clamps
Strain Relief
Electrical Cable
or Power Cord
Hot Water Line
TOOLS YOU WILL NEED:
Tools Required for All Installations
¨ Phillips head and flat blade screwdrivers
¨ 3/8”, 5/16” and 1/4” nutdrivers
¨ Level
¨ Carpenters square
¨ Measuring tape
¨ Safety glasses
¨ Flashlight
¨ Bucket to catch water when flushing the line
¨ Tubing cutter
¨ Gloves to protect against sharp edges
¨ Wire strippers
For New Installations Only:
¨ Drill and appropriate bits
¨ Hole saw set
Gloves
Wire Strippers
Level
Flat Blade Screwdriver
Safety Glasses
Bucket
Measuring Tape
Nut Driver
Phillips Head
Screwdriver
Tubing
Cutter
Flashlight
Adjustable
Wrench
Drill
and Bits
Square
Hole
Saw Set
4
Installation Preparation
PARTS SUPPLIED:
Remove the hardware accessory bag and other parts
from inside or taped to the outside of the dishwasher.
Check contents against illustrations to insure that all
parts are included.
¨ 2-piece toekick
¨ 6 screws (see illustration)
¨ 2 leveling legs
¨ Template for the installation of a
custom panel packed with models
ZBD7000 and ZBD7005 only
¨ Junction box cover
Junction
Box Cover
with screws
2 Leveling Legs
Template
for
ZBD7000
ZBD7005
Only
Template with Mounting Hardware
Screws A
(2) Countertop
Mounting
Screws
Screws B
(2) Cabinet
Mounting
Screws
Screws C
(2) Color
Matched
Toekick
Screws
PREPARE DISHWASHER ENCLOSURE
This Wall Area
must be Free of
34" to 35"
Underside
of Countertop
to Floor
*Models ZBD7000 and ZBD7005 with custom panels are 24-3/4" deep
• The rough cabinet opening must be at least 24” deep,
23-7/8”min. to 24-1/4” wide. The height should be 34”
min. and 35” max.
Note: ADA installation, beneath 34" high countertops may be accomplished by removing front leveling legs. Drain hose, water and
electrical must be routed through the cutout on the back of the
dishwasher.
• The dishwasher must be installed so that drain hose is
no more than 10 feet in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides
and back, but should not support any part of the
enclosure.
Pipes or Wires
1-3/4"
23-7/8" Min.
24-1/4" Max
24"
Min.
6"
Insulation
2-Piece Toekick with
Sound Insulation
• The floor inside the opening must be even and level
with the finished floor of the kitchen. If the kitchen
floor is tile, it may be
higher than the floor of
the installation cutout.
Pieces of wood may be
placed into the cutout
floor to make it level or
higher than the room
floor. This will allow easy
20-1/2"
removal for any future
service.
Corner Installation
• When installing into a
corner, allow 2" min.
clearance between
dishwasher and adjacent
cabinet or wall.
• Allow 24-1/8" min.
clearance from the front
of the dishwasher for door
opening.
Countertop
Dishwasher
Clearance for Door
Opening 2" Minimum
24-1/8"
5
Loading...