GE ZBD0700K01II, ZBD0700K03II, ZBD0700K10II, ZBD0700K15II, ZBD0700N00II Installation Guide

...

Download

Installation Instructions

Built-In Dishwashers

ZBD6800 ZBD6880 ZBD6890* ZBD0700* ZBD0710

Design Guide with Installation Instructions

*For ZBD6890 and ZBD0700 also refer

to the instructions provided on the template packed with that model.

Monogram:

Safety Information

BEFORE YOU BEGIN

Readthese instructionscompletelyandcarefully.

IMPORTANT- Savetheseinstructionsfor

local inspector's use.Observe all governing codes and ordinances.

• Note to Installer -- Besureto leavethese

instructions with the Consumer.

• Note to Consumer -- Keeptheseinstructions

with your Owner'sManual for future reference.

• Skill Level --Installation of this dishwasher requires

basic mechanical and electrical skills. Properinstallation

is the responsibilityofthe installer.Productfailure due to improperinstallationis not coveredundertheGE ApplianceWarranty.

• Completion "13me-- 1 to 3 Hours.

New installations require moretime than replacement

installations.

CONTENTS

InstallationPreparation

Parts Supplied..............................................................................3

Materials YouWill Need............................................................3

ToolsYouWill Need ....................................................................3

Models Available ........................................................................4

Advance Planning......................................................................4

Prepare Dishwasher Enclosure................................................4

Drain Requirements ....................................................................5

Prepare Electrical Wiring ..........................................................6

PrepareHotWater Line..............................................................7

InstallationInstructions

Step 1, Check DoorBalance......................................................7

Step 2, RemoveWood Base, InstallLeveling Legs ..............8

Step3, RemoveToeKick ............................................................8

Step4, InstallPower Cord ........................................................8

IMPORTANT --The dishwasher MUST

be installed to allow for future removal from the enclosure if service is required.

If you received a damaged dishwasher, you should immediately contact your dealer or builder.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

FOR YOUR SAFETY

Readandobserveall CAUTIONandWARNINGSshown

throughouttheseinstructions. While performinginstallationsdescribedinthis booklet,

gloves,safetyglassesorgogglesshouldbeworn. ForMonogramlocal service in yourarea, 1.800.444.1845.

ForMonogramservice in Canada1.888.880.3030 ForMonogramPartsandAccessories,call 1.800.626.2002.

Step 5, Install 90° Elbow ............................................................8

Step 6, PositionWater Lineand HouseWiring ......................9

Step 7, Install Drain Hose,GuideThrough Cabinet ..............9

Step 8, Slide Dishwasher Partially Into Cabinet....................9

Step 9, Install TrimPieces..........................................................9

Step 10,Position Dishwasher Under Countertop ................10

Step 11,Level Dishwasher ......................................................11

Step 12,Secure Dishwasher To Cabinet ..............................12

Step 13,ConnectWater Supply ..............................................13

Step 14,Connect Drain Line....................................................13

Step 15,Connect Power Supply..............................................14

Step 16,Pre-TestCheck List....................................................14

Step 17,Dishwasher Wet Test................................................15

Step 18,Replace Toekick ........................................................15

Step 19,Literature ....................................................................15

CustomPanelDimensions

CustomPanel for Models ZBD6890,ZBD0700......................15

Installation Preparation

PARTS SUPPLIED:

[] Two #8-18x 5/8"Phillips special headscrews, to secure

dishwasher to underside of countertop or sides of

cabinets. (Tapedto top side of dishwasher.) [] Side andtop trim pieces (on some models) [] Templatewith mounting hardware (not shown)

for Model ZBD6890Only

[] Drain Hoseand HoseClamp

MATERIALS YOU WILL NEED:

[] Ferrule, compression nut and 90° Elbow (3/8"NPT

external thread on one end, opposite end sizedto fit

water supply) [] Thread seal tape [] ULListedwire nuts (3)

Materials For New Installations Only:

[] Air gapfor drain hose, if required [] Waste tee for house plumbing,if applicable [] Electrical cable or power cord, if applicable [] Screw type hose clamps

[] Strain relief for electrical connection [] Handshut-off valve

[] Water line 3/8"rain.copper [] Couplerfor extending drain line, if applicable

Waste Tee

#8 Phillips Special Head

Screws 5/8"Long

Drain Hose

90° Elbow, Ferrule and

Compression Nut

Electrical Cable Hot Water line

(or Power Cord,if applicable@

Screw Type Strain Relief

Air Gap Hose Clamps

_ HoseClamp

Hand Shut-Off Thread

Valve Seal Tape

Trim Pieces

(on some models)

Wire Nuts (3)

Coupler

TOOLS YOU WILL NEED:

[] Phillips headscrewdriver [] 5/16"and 1/4"nutdriver

[] 6"Adjustable wrench [] Level

[] Carpenterssquare [] Measuring tape [] Safetyglasses [] Flashlight [] Bucketto catch water when flushing the line [] 15/16"socket (optional for skid removal)

[] Gloves

For New Installations Only:

[] Tubing cutter [] Drill and appropriate bits

[] Holesaw set

Gloves Bucket

Ph and 5/16" Head

Screwdriver

_115/16" Socket

Flashlight

1/4" Nutdriver

n6''AdJ_t_table

Level

Tubing Cutter

Carpenters Square

........... t

I dddihhhhhhhhl

Measuring Tape

Installation Preparation

ADVANCE PLANNING

• These dishwashers are designed for versatility,

adaptable to virtually any installation.

• All models have a full length door without the

traditional access panel.

• These dishwashers may be installed beneath

countertops of stone or other materials that will not accept screws. No trim kit required.

PREPARE DISHWASHER ENCLOSURE

ThisWallArea

34-1/2"Min, Undersideof Square

Countertop and

toFloor Plumb

Pipesorwires

DISHWASHER MODELS

ZBD0710 SS, Stainless Steel ZBD6880 SS, Stainless Steel ZBD6800 BB, Black ZBD6800 WW, White ZBD6890 Requires a 3/4" custom panel and handle ZBD0700 Requires a 3/4" custom panel and handle

,WARNING

To reduce the risk of electric shock, fire, or injury to persons, the installer must

ensure that the dishwasher is completely enclosed at the time of installation.

Figure B

Countertop

Min_

FloorMUST

beEvenwith

RoomFloor

*Dishwasher models ZBD6890

andZBDO700require a 3/4"

thick custom panel and will be

24-3/4" deep.

• The rough cabinet opening must be at least 24" deep, 24"wide and approximately 34-1/2" high from floor to

underside of the countertop.

• Plumbing and electrical service must enter the shaded

area.

• The dishwasher must be installed so that drain hose is

no more than 10feet in length for proper drainage.

34"

Adjustable to 35"

FigureA

Dishwasher

Opening2"Minimum

CLEARANCES:When installed into acorner, allow 2"min.

clearance between dishwasher and adjacent cabinet, wall or

other appliances. Allow 28-3/8" min. clearance from the front of

the dishwasher for door opening (Figure B).

Installation Preparation

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10 feet distance to drain.

• Do not connect drain lines from other devices to the dishwasher drain hose.

NOTE: An air gap must be used, if waste tee or disposer connection is less than 18" above floor to prevent siphoning,

DETERMINE DRAIN METHOD

The type of drain installation depends on the following question. [] Do local codes or ordinances require an air gap?

[] Is waste tee less than 18"above floor?

If the answer to either question is YES, Method 1MUST be used.

• If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2" dia, hole in the cabinet wall within the shaded areas shown in Figure Afor the drain hose

connection. The hole should be smooth with no

sharp edges,

Method 1--Air Gap with Waste Tee or Disposer An air gap must be usedwhen required bylocal codes and

ordinances. The air gap must beinstalled according to manufacturers instructions.

__;_ re

Figure C

Method 2--"High Drain Loop" with Waste Tee or Disposer

_.___

32 _

i Min. -L_

IMPORTANT-when

connecting drain line to disposer, check to be sure that drain plug has

been removed. DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE,

Remove

FigureD

Hopper

Plug

Installation Preparation

PREPARE ELECTRICAL WIRING

FORPERSONAL SAFETY:Remove house

fuse or open circuit breaker before

beginning installation. Do not use an

WARNING

extension cord or adapter plug with this appliance.

1-1/2" Dia.

Hole(Max.)

Electrical Requirements

• This appliance must be supplied with 120V,60 Hz., and

connected to an individual properly grounded branch circuit, protected by a 15or 20 ampere circuit breaker

or time delav fuse.

• Wiring must be 2-wire with ground and rated for 75°C (176°F).

• If the electrical supplv does not meetthe above

requirements, call a licensed electrician before proceeding.

Grounding Instructions--Cable Direct

This appliance must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and be connected to the equipment grounding terminal or

lead on the appliance. Grounding Instructions--Power Cord Models

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and

ordinances.

WARNING

The improper connection of the equipment grounding conductor can result in a risk of electric shock, Check with a qualified electrician or service representative if you are in doubt that the appliance is properly grounded,

from

Cabinet

Receptacle

Location

FigureE

Formodels equipped with power cord:Do not modify

the plug provided with the appliance; if itwill not fit the outlet, have a proper outlet installed by a qualified

technician.

Cabinet Preparation and Wire Routing

• The wiring may enter the opening from either side, rear orthe floor within the shaded area.

• Cut a 1-1/2" max. dia. hole to admit the electrical cable. Cable direct connections may pass through

the same hole asthe drain hose and hot water line,

if convenient. If cabinet wall is metal, the hole edge must be covered with a bushing.

NOTE: Power cords with plug must pass through a

separate hole.

Electrical Connection to Dishwasher Electrical connection is on the right front of

dishwasher.

• For cable direct connections the cable must be routed as shown in Figure E.Cable must extend

a minimum of 24" from the rear wall.

• For power cord connections, install a 3-prong

grounding type receptacle in the sink cabinet rear wall, 6" rain. or 18"max. from the opening, 6" to 18"

above the floor.

Area

White

Installation Instructions

PREPARE HOT WATER LINE

• The line may enter from either side, rear or floor within the shaded area shown in Figure E

• The line may pass through the same hole as the

electrical cable and drain hose. Or, cut an additional 1-1/2" dia. hole to accommodate the water line.

If power cord with plug is used, water line must not pass through power cord hole.

j / I I \

/ I I \

/4- ]'\

I l \\

fl I,,

Shut-off 1-1/2 Dia. ]

Valve Hole | i

,,,, /4- - ..... - -I,

Hoti::::: !,:::_ I:

F[om Z_// 19" FromWall \

Cab,net /[/_--2" FromFloor X--

Cabinet Face-_ FigureF

Water Line Connection

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location, such as under the sink. (Optional, but strongly

recommended and may be required by local codes.)

• Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than 3/8" O.D.copper tubing. Route the line as shown in Figure F

and extend forward at least 19"from rear wall.

• Adjust water heater for 120°F to 150°Ftemperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120 PSI.

BEFORE YOU BEGIN

Locate and set aside (for use in Step 12) the 2 Phillips special head screws wrapped with

yellow tape and stuck to the top or side of the

dishwasher. Remove drain hose from upper rack, if it has not been pre-installed, and set aside for use in Step 7.

[STEP 11CHECK DOOR BALANCE

• With dishwasher on the wood skid, check the door balance by opening and closing the door.

• If the door drops when released, increase the spring

tension. If the door rises when released, decrease the tension.

NOTE: The addition of the custom panel on model ZBD6890 will require exchange of the factory installed springs. Use the heavy-duty springs provided. See the custom panel template for additional instructions.

• Position the spring for increased or decreased

tension as required.

NOTE: Adjust both balance springs to the same amount of tension to prevent excessive door

twisting during use.

FigureG

CAUTION

Do not remove wood base until you are ready to install the dishwasher. The dishwasher will tip over when the door is opened if the wood base is removed.

Pulle

Decrease

Tension

Shoulder

CorrectSpring Tension CableRouting

TIP: If door does not open easily or falls too quickly, checkthe spring cable routing. Checkthatthe cable is properly aligned on the pulley (as shown).

Installation Instructions

ISTEP21REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT- Donotkickoffwoodbase!Damage

will occur.

• Move thedishwasher closeto the installationlocationandlayit on its back.

•Removethe fourleveling legsonthe undersideofthe wood basewith anadjustablewrench or 15/16"socket.

•Discardbase.

Figure H

•Screw levelinglegs backintothe dishwasherframe, approximately1/4"from frame as shown.

[STEP41INSTALL POWER CORD

UsePowerCordKitWX09XT0910availableforpurchasefroman authorizedGEAppliancesdealer.

Skipthisstepif dishwasherwill bedirectwired orhasa

factoryinstalledpowercord.

Thepower cordand connectionsmustcomplywith the National ElectricalCode,Section422and/or localcodesandordinances.

• Maximumpower cord lengthis 4feet beyondthe back of the dishwasher.

A B

Remove Insert Power

Junction Box CordWires

Cover Strain Relief

_ andTighten

Whit

Gr°u L

C CheckThat White, Blackand_

GreenDishwasher Wires Are Threaded

Thru Small Hole in Bracket

Figure K

UseUL Listed _ ///

Wire Nuts _/

ISTEP31REMOVE TOEKICK

• Removethe twotoekick screws.

Remove2

ToekickScrews

FigureJ

• Connectincomingpowercordwhite (orribbed)to dishwasher white, black(or smooth)to blackand groundto dishwasher

greenwire. UseULlistedwire nutsof appropriatesize.

• Replacejunctionboxcover.Besurewires are not pinched underthe cover.

[STEP 51 INSTALL 90 ° ELBOW

•Wrap90°elbowwith thread sealtape.

• Installa 90 elbow ontothe water valve.

Frontof Dishwasher

_ Water Valve

Elbow

90°_

II Hose

Thread

FigureL SealTape

Bracket

• Donotovertighten90° elbow,water valve bracketcouldbend or water valvefitting couldbreak.

• Positionthe endof the elbowtoface the rear ofthedishwasher.

Installation Instructions

ISTEP61POSITION WATER LINE

AND HOUSING WIRING

• Position water supply line and house wiring on the floor of the opening to avoid interference with base of dishwasher and components under dishwasher.

" " 4"

_,,5_____...._:__

House\\ \

FigureM

ISTEP71INSTALL DRAIN HOSE,

• Remove tape and wire tie holding the clamp to the drain hose. Be careful not to damage the drain hose.

• Stand the dishwasher upright.

• Slip the supplied

hose clamp over

the large end of the hose. Do not

tighten.

W_tner Wiring _ \

GUIDE THROUGH CABINET

ISTEP 81SLIDE DISHWASHER

PARTIALLY INTO CABINET

DO NOT PUSH AGAINST FRONT PANELWITH KNEES. DAMAGE WILL OCCUR.

• Slide dishwasher into the opening a few inches at a time.

_er

byGrasping Both

DoNot PushAgainst FrontDoorPanelWith

Knee.Damageto The DoorPanelWill Occur.

• As you proceed, pull the drain hose through the

opening under the sink. Stop pushing when the dishwasher is a few inches forward of adjacent

cabinetry.

• Make sure drain hose is not kinked under the

dishwasher and there is no interference with the water line and wiring or any other component.

SidesWith Hands

FigureP

Figure N

• Push hose over the drain outlet on the back side of the dishwasher. See illustration. Push the hose over the outlet and against the shoulder stop,

• Tighten the hose clamp with a 1/4" nut driver.

Insulation

Blanket Water

House

Figure0

Power Cord

• Position the dishwasher in front of the opening.

Insert drain hose into the cabinet side. If power cord is used, guide the end through a separate hole, 9

Wiring

(If Used)

ISTEP 91INSTALL TRIM PIECES

Skip this step if trim is not supplied with the dishwasher.

• Locate trim strips inside dishwasher,

• Press trim onto the tub flange on each side, Start with the top edge, pressing on as you move towards

the bottom,

• Press the two top trim pieces on each side of the latch,

• Open and close the door to check that trim does not

bind and does not interfere with door latch.

Trim Strip

Strip

Figure Q

Installation Instructions

ISTEP 101 POSITION DISHWASHER UNDER COUNTERTOP

• Push the dishwasher into the cabinet.

• Push at the sides with your hands. Do not use your knee against the door since door damage will occur.

• Check that the tub insulation blanket does not get "bunched-up" or interfere with the springs as you

slide it into the cabinet.

• Center the dishwasher in the opening.

• Check that the edges of the dishwasher door are behind the cabinet frame and aligned with the front

face of the cabinet as shown.

• Carefully open and close the door to ensure that the door panel does not catch or rub on the cabinet frame.

• If the door catches or rubs on the frame, reposition and/or level the unit (see Step 11) until the door moves freely and does not contact the cabinet frame.

The controls are designed to be hidden by your countertop. Align the dishwasher as shown in Figure T.

Do Not PushAgainst Sides With Hands er

Front DoorPanelWith Knee.Damageto The

Door PanelWill Occur. FigureR

NOTE: If the drain hose gets trapped between the wall and the back side of the dishwasher, it can prevent the dishwasher from sliding all the way back into the cabinet opening, and thus preventing aflush fit with the kitchen cabinet panels.

TIP: For best appearance installations of custom panel models, it may be necessary to cut off the back panel

of the tub insulation blanket so that the dishwasher door panel can be aligned flush with the kitchen

cabinet panels. The leveling legs can be used to increase or decrease

the amount of gap between the controls and the countertop affecting the visibility of the controls. Leave a 1/2"minimum gap between the underside of the countertop and the top of the dishwasher door (see Figure V).

IMPORTANT- Leave a 1/2" minimum

gap between the controls and the underside of the countertop to prevent condensation and damage to the control panel from screwheads.

NOTE: If this dishwasher is replacing an existing

dishwasher, the old countertop bracket screw holes may not be in the correct position to accept a top control model. New holes may be required.

Door

Fitsand

Swings

Back

Behind

Cabinet\

Frame

Correct

Alignment

,'' Top View

,,,,,''''' Mo .,oml

ControlsHidden

byCountertop FigureT

Countertop

FigureS

2 mm.

FigureV

Figure U

Installation Instructions

ISTEP 111 LEVEL DISHWASHER

IMPORTANT- Dishwasher must be level

for proper dish rack operation and wash performance.

and rack track inside

• Place level on door / the tub as shown to f

check that the //(fi _//

dishwasher is level. ///// ////

J__o Side

• Level the dishwasher by

adjusting the

four leveling legs

individually.

• Make sure 1/2"

minimum gap is maintained (see Figure V).

If adjustment to the right rear leveling leg is required, gain access by loosening junction box bracket screw (through the access hole) and rotate bracket

clockwise,

TIP: Pull lower rack out, about halfway, Check to be sure the rack does not roll forward or back into

dishwasher. If the rack rolls in either direction, the dishwasher must be leveled again,

• If the door hits the tub, the dishwasher is not installed correctly, Adjust leveling legs to align door to tub,

Access Hole

Turn Legsl /

_ FigureX

Installation Instructions

ISTEP 121SECURE DISHWASHER TO CABINET

The dishwasher must be secured to the countertop or the cabinet sides. When countertops are made of wood, use Method 1.When countertops are granite or other materials that will not accept screws, use Method 2 to

secure dishwasher atthe sides.

IMPORTANT-After leveling, verify that

the dishwasher is still in the correct position shown in Step 10.

Method 1--Secure dishwasher to wood countertop

• Fasten the dishwasher to the underside of the countertop with 2 Phillips screws provided,

Brackets

Wood Countertop

Side Mounting

Brackets

Figure Y

Countertop

Mounting

Tub

Brackets

Figure Y

IMPORTANT- Drivescrewsstraightand

flush. Protruding screw heads will scratch the top or sides of the control panel and can interfere with door closing.

t_I Figure Z

Method 2--Secure dishwasher with side mounting brackets

• Remove plug buttons (one on each side).

• Install screw through the hole in the side of the

dishwasher and into the adjacent cabinet.

Reinstall plug buttons.

Stone Countertop SideMounting Brackets

FigureAA

Both Methods--Maintain 1/2" Gap

Installation Instructions

ISTEP131CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

• Slide compression nut, then ferrule over end of water line.

• Insert water line into 90° elbow.

• Slide ferrule against elbow and secure with

compression nut.

IMPORTANT- Check to be sure that door

spring does not rub or contact the fill hose or water supply line. Test by opening and closing the door. Re-route the lines if a rubbing noise or interference occurs.

Line

Figure CC

90° Elbow

DoorSpring

ISTEP 141CONNECT DRAIN LINE

FOLLOW ALL LOCAL CODES AND ORDINANCES,

The drain hose molded end will fit 5/8" or 1"diameter connections on the air gap, waste tee or disposer. Cut

on the marked line as required for your installation.

Cutting Line

FigureDD

IMPORTANT:Do not cut corrugated

portion of hose

• If a longer drain hose is required, add up to 42"of

length for a total of 10ft. to the factory installed hose. Use 5/8" or 7/8" inside diameter hose and a coupler to

connect the two hose ends. Secure the connection

with hose clamps.

DRAIN LINE INSTALLATION

• Connect drain line to air gap, waste tee or disposer using either previously determined method.

Method 1--Air gap with waste tee or disposer

__ re __ re

Waste TeeInstallation Disposer Installation

FigureFF

Method 2--"High drain loop" with waste tee or disposer

Fasten to underside

_ _ of countertop,

Fasten to underside

i_ of countertop,

32"

Figur_

Coupler

HoseClamp

• Secure the drain hose to the air gap, waste tee or disposer with clamps.

NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED

10 FEETFORPROPER DRAIN OPERATION.

HoseClamp

Waste Tee Installation

Figure GG

IMPORTANT-when i--_/__ Remove

connecting drain line to disposer, _1 Hopper check to be sure that drain plug has ,._ Plug

been removed. DISHWASHER WILL NOT DRAIN IF PLUG IS LEFT IN PLACE.

TIP: Avoid unnecessary service call charges. Always be sure disposer drain plug has been removed before attaching dishwasher drain hose to the disposer.

Disposer Installation

Installation Instructions

ISTEP151CONNECT POWER SUPPLY

Skip this step if equipped with power cord, Goto step 16.

Verify that power is turned off at the source,

• Remove junction box cover "A".

• Secure house wiring to the back of the junction box with a strain relief "B".

• Locate the three dishwasher wires, (white, black

and green) with stripped ends. Insert dishwasher

wires through the small hole in the junction box "C".

Use wire nuts to connect incoming ground to green,

white to white and black to black "D".

• Replace junction box cover "E". Check to be sure that wires are not pinched under the cover.

A B

Remove InsertPower

JunctionBox CordWres Thru

Cover StrainRelief

_ andTighten i White

CCheckThatWl_ B_ik-lnd _ i

GreenDishwasherWires Are Threaded

ThruSmall Holein Bracket D

E ReplaceJunction BoxCover

, Gr°und___ Black

UseULListed

Wire Nuts

FigureHH

ISTEP 161PRE-TEST CHECK LIST

Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty,

[] Check to be sure power is OFF. [] Open door and remove all foam and paper

packaging.

[] Locate the Owner's Manual in the literature

package. [] Read the Owner's Manual for operating instructions. [] Check door opening and closing. If door does not

open and close freely or tends to fall, check spring

cable routing and spring adjustments. See Step 1. [] Checkto be sure that wiring is secure under the

dishwasher, not pinched or in contact with door springs or other components. See Steps 8 and 10.

[] Check door alignment with tub. If door hits tub,

level dishwasher. See Step 11. [] Pull lower rack out, about halfway. Check to be

sure it does not roll back or forward on the door.

If the rack moves, adjust leveling legs. See Step 11. [] Check door alignmentwith cabinet. If door hits

cabinet, reposition or relevel dishwasher. See

Steps 10,11 and 12. [] Check that door spring does not contact water line,

fill hose, wiring or other components. See Step 13.

If house wiring is not 2-wire with ground, a ground must be provided by the installer. When house wiring is aluminum,

WARNING

be sure to use UL Listed anti-oxidant compound and aluminum-to-copper

connectors.

[] Verify water supply and drain lines are not kinked

or in contact with other components. Contact with

motor or dishwasher frame could cause noise. See Steps 6 and 8.

[] Turn on the sink hot water faucet and verify water

temperature. Incoming water temperature must

be between 120°F and 150°F.A minimum of 120°F

temperature is required for best wash performance.

See "Prepare Hot Water Line," page 7.

[] Add 2 quarts of water to the bottom of the

dishwasher to lubricate the pump seal.

[] Turn on water supply. Check for leaks. lqghten

connections if needed.

[] Remove protective film if present from the control

panel and door.

Installation Instructions/Custom Panel Dimensions

ISTEP 171 DISHWASHER WET TEST

[] Turnon powersupply(or plugpower cordintooutlet,if

equipped).

[] Startthe unitto checkfor leaks.

- PushRINSEONLYpad.

- PushSTART/RESETpadonetime.

- Closedoor.

[] Checkto besure thatwater entersthe dishwasher.If water

doesnot enterthe dishwasher,checkto besurethatwater and powerareturned on.

[] Checkfor leaksunderthe dishwasher.If a leakisfound,turn

powersupplyoff,thentighten connections.Restorepower

after leakis corrected.

[] Checkfor leaksaroundthe door.A leakaroundthe door

couldbe causedby door rubbingor hittingagainstadjacent cabinetry.Repositionthe dishwasherif necessary.SeeStep12.

[] Thedishwasherwill drainandturn off about5minutesafter it

was started.Checkdrain lines.If leaksarefound,turn power off atthe breakerandcorrect plumbingas necessary.Restore

powerafter correctionsare made.SeeStep 15.

[] Opendishwasherdoorandmakesuremost ofthe water has

drained.If not,check that disposerplughasbeenremoved and/orair gap isnotplugged.SeeStep14.Also checkdrain linefor kinking.

[STEP191LITERATURE

• Besureto leavecompleteliteraturepackageand installation instructionswith the consumer.

CUSTOM PANEL FOR MODEL ZBD6890, ZBDO700

Thesedishwashersrequireafield installed3/4"thick custom paneland customhandle.Aninstallationtemplateis packed

with thesemodelsandmay beobtainedin advance.Order

Pub.No.31-30569-1.Completepanelinstallationinstructions are includedonthe template.

CUSTOM PANEL SEE REQUIREMENTS

HEIGHT Panelheightmustbebetween30-1/16"and30-1/4".

30-1/16" Min. 30-1/4" Max.

[] Runthedishwasherthroughanother"Rinse0nly" cycle.

Checkfor leaksand correctif required.

ISTEP181REPLACE TOEKICK

• Placetoekickagainstthelegsof the dishwasher.

Figure II

•Alignthetoekick with the bottomedgeandmakesureit is againstthefloor.

•Insertandtightenthe two toekick attachmentscrews.The toekick shouldstay in contactwith the floor.

TIP:Make suretoekick isagainstfloor to minimizenoise.

_23-3/4"_

• Ifthe panelheightis morethan30-1/4"itwill preventthe door from swingingopen.

• Ifthe panelheightis lessthan 30-1/16"it will not coverthe dishwasherdoorframe.

•Thetop ofthe custompanelmustbeflush with thetop ofthe door.The 1/2"minimumgapbetweenthetop ofthe doorand the bottomofthe countertopmust bemaintained.

Countertop

Z2"mio

WIDTH

Panelwidth mustbe23-3/4".

• Ifthe panelwidth is lessthan23-3/4"itwill notcoverthe dishwasherframe.

IMPORTANT:Toensureoptimumdoorbalanceperformance,

thecustompanelmustnotweigh morethan14Ibs.

Pub.No.31-30586 ] PartNo.206C1559P126J

11_04JR

NOTE:While performing installations described inthis book, safety glasses or goggles should be worn.

I_." Motwg'r.m °'_loon! ._t._-vic_"itt yo_tr _tre., .ill

l. 800.444. 1845.

NOTE: Pro(hl(:t iml)rov¢_m(nl is a cot_tinuing (:ride ax'or _t (;(_n(_l-_d El(_(tric. Tller(_i_r(, malel-ials, _q)l)(_n-an(¢_ and

Sl)(_(i_](_lions _t'(_ sul)je(t to (ll_lng(' wilhoul noli(¢!.

Monogram:

GEConsumer & Industrial LouisviIJe, KY40225

@2004GECompany

GE ZBD0700K01II, ZBD0700K03II, ZBD0700K10II, ZBD0700K15II, ZBD0700N00II Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual