Page 1
2
Important Safety Information
4
Operating Instructions
The Controls on Your Washer
Other Washer Features
Preparing to Wash
Care of Product
10
Helpful Information
Specialized Fabric Guide
11
If Something Goes Wrong
Washer
Owner’s Manual
Model: YISR309JT
175D1807P286
79-90019
7-99 JR
Printed in the United States
Page 2
2
Water Heater Safety
Important Safety Information
Read all safety information before using
Under certain conditions
hydrogen gas may be produced
in a water heater that has not
been used for two weeks or more.
HYDROGEN GAS CAN BE
EXPLOSIVE UNDER THESE
CIRCUMSTANCES.
If the hot water has not been used
for two weeks or more, prevent
the possibility of damage or injury
by turning on all hot water taps
and allow them to run for several
minutes before using any
electrical appliance which is
connected to the hot water
system. This will allow any
hydrogen gas to escape. Since
the gas is flammable, do not
smoke or use an open flame
or appliance during this process.
SAVE THESE INSTRUCTIONS
Page 3
• Use this appliance only for its
intended purpose as described
in this Owner’s Manual.
— Properly ground to conform
with all governing codes and
ordinances. Follow details in
Installation Instructions.
— Install or store where it will not be
exposed to temperatures below
freezing or exposed to the weather.
• Do not repair or replace any
part of the appliance or attempt
any servicing unless specifically
recommended in this Owner’s
Manual or in published userrepair instructions that you
understand and have the skills
to carry out.
• Do not tamper with the controls.
• Never reach into the washer
while it is moving.
• Close supervision is necessary
if this appliance is used by or
near children or infirm persons.
Do not allow children to play
inside, on or with this appliance
or any discarded appliance.
Dispose of discarded appliances
and shipping/packing materials
properly. Before discarding
a washer, or removing from
service, remove the washer lid.
• Do not wash or dry articles that
have been cleaned in, washed
in, soaked in, or spotted with
combustible or explosive
substances (such as wax, oil,
paint, gasoline, degreasers,
dry-cleaning solvents, kerosene,
etc.) which may ignite or
explode. Do not add these
substances to the wash water.
Do not use these substances
around your washer and/or
dryer during operation.
• To minimize the possibility
of electric shock, unplug this
appliance from the power supply
or disconnect the washer at the
household distribution panel by
removing the fuse or switching
off the circuit breaker before
attempting any maintenance
or cleaning.
• NOTE: Turning the Cycle
Selector knob to an off position
does NOT disconnect the
appliance from the power supply.
3
Warning
To reduce the risk of fire, electric shock, or injury to persons
when using your appliance, follow basic precautions, including
the following sections.
Safety Precautions
Page 4
4
By selecting load size, you are setting the
water level. For the best results, select a size
appropriate for the load you are washing.
This refers to the speed of the agitator during
the wash and the basket during the spin.
With the Normal wash speed the agitator moves
faster. Use for cottons, denims and play clothes.
With the
Gentle wash speed the agitator moves
slower. Use for delicate and knit items.
The Fast spin speed is for durable items.
The Slow spin speed is for delicate items like
sweaters and lingerie. Clothes will be less dry
than when using a fast spin speed.
Operating Instructions
The controls on your washer
LOAD SIZE
RESET
MEDIUM
LARGE
SMALL
SUPER
1 2 3
2
1
Load Size Wash/Spin Speed
Page 5
5
Always follow Fabric Manufacturer’s Care
Label or instructions when laundering. Use
this chart as a general guide.
• Push in the Cycle knob to select the desired
cycle. See the above Cycle Descriptions.
• Add detergent.
• Add clothes and close lid.
• Pull out the Cycle knob to start washer.
Cycle Descriptions
For information on fabric care for specialty
items see the Specialty Care Guide.
4
wash
temperature
hot
warm*
warm*
cold
warm*
rinse
temperature
cold
cold
cold
cold
warm*
4
3
Wash/Rinse Temp
Selecting Cycle/Starting Washer
COTTONS WHITE
COTTONS COLORS
PERMANENT PRESS
DELICATES
WASHABLE WOOLENS
See next page for other washer features
*Warm water is approximately 32°C. to 43°C. (90°F. to 110°F.) (hand comfortable).
COTTONS REGULAR
For heavily to lightly
soiled cottons, linens,
work and play clothes.
PERMANENT PRESS
For synthetics and
blends with normal soil.
KNITS
Specially designed for
normally soiled knits.
DELICATES
For lingerie and
specialcare fabrics with
light to normal soil.
Wash/Rinse Temperature Guide
AUTO SOAK
For heavily soiled
clothes. Begins with a
brief agitation, soaks
for a specified period of
time, then moves
through the rest of the
cycle automatically.
Page 6
6
Operating Instructions
Other washer features your model may have
This dispenser dilutes liquid
chlorine bleach before it reaches
into your wash load. To use, follow
these steps:
1
Check clothing care labels for
special instructions.
2
Measure liquid bleach carefully,
following instructions on bottle.
3
Before starting the washer, pour
measured amount of bleach
directly into bleach dispenser.
Avoid
splashing or over-filling
dispenser.
NOTE:
•
Never pour undiluted liquid chlorine
bleach directly onto clothes or into
the wash basket.
•
Do not pour powdered bleach
into bleach dispenser. If you prefer
to use powdered bleach, pour it
into the wash basket with your
detergent.
Liquid Bleach
Dispenser
Pour liquid bleach into bleach
dispenser
This cap fits into the top of the
agitator. If it accidentally comes off,
simply put it back on.
Agitator Cap
Do not pour anything into the
agitator if the top is removed
When you use extra detergent
or bleach to clean heavily soiled
clothes, you may want to use the
Extra Rinse option. This option
provides a second deep cold rinse
in the Cottons Regular cycle. Turn
the Extra Rinse knob to SET.
The washer will pause for a few
minutes before the Extra Rinse
option begins.
Extra Rinse
OFF
SET
Page 7
This dispenser automatically
releases liquid fabric softener at the
proper time during the cycle. To
use, follow these steps:
1
Make sure dispenser is securely
attached to agitator.
2
Pour liquid fabric softener
into dispenser, using amount
recommended on package.
3
Add water to dispenser until it
reaches the maximum fill line.
NOTE:
•
Do not stop the washer during
the first spin. This will cause
the dispenser to empty too soon.
•
Do not use the Fabric Softener
Dispenser with the Auto Soak.
•
Never pour fabric softener directly
on clothes. It will leave spots on
clothes.
•
Only use dispenser for liquid fabric
softeners. If dispenser gets clogged,
see Cleaning section below.
Do not pour anything into the
agitator if the top is removed
Fabric Softener
Dispenser
1
Remove the dispenser from the
top of the agitator.
2
Separate the dispenser cup from
the cover by grasping the top and
pushing down on the inside of the
cup with your fingers. Dispenser
cup will pop free from the cover.
3
To clean dispenser, soak both the
dispenser cup and the dispenser
cover in a solution of warm water
and liquid detergent.
4
If necessary, loosen build-up with
a clean, soft cloth after soaking.
Do not use a stiff brush; you may
roughen the surface of the
dispenser.
5
Rinse and reassemble dispenser.
Place dispenser back on the
agitator.
Cleaning Fabric
Softener Dispenser
Pour liquid fabric softener
and water into fabric softener
dispenser
Separate for cleaning
The lint filter is located under the
agitator. It is self-cleaning and
requires no maintenance.
Lint Filter
7
Page 8
8
Operating Instructions
Preparing to Wash
Always follow Fabric Manufacturer’s
Care Label when laundering.
Sort by color
(Separate colorfast from
non-colorfast fabrics*)
• Whites
• Lights
• Darks
Separate by fabric type
• Cottons and linens
•
Permanent press cottons and
blends
• Synthetic and poly knits
• Delicates
Separate lint producers from
lint collectors
• Lint producers: terry cloth and
chenille
• Lint collectors: velveteen and
corduroy
Sort by soil
• Light
• Medium
• Heavy
* Non-colorfast fabrics may bleed or fade. Sort by
individual color.
Sort
Always add detergent before
adding clothes so that the
detergent can work effectively.
Using the correct amount of
detergent is one of the most
important things you can do to
make sure your wash comes out
clean. Always follow the detergent
package directions.
Using too little detergent is
a common cause of laundry
problems. Use more detergent if
you have hard water, large loads,
greasy or oily soils or lower water
temperature.
Detergent
Page 9
Load dry items loosely, spacing
evenly around agitator, and close
the lid.
A typical wash load: two twin sheets,
two tablecloths, four collared
shirts, three pillow cases, three
small bath
towels, three t-shirts,
and three pairs of shorts
.
Place large items in bottom, small
items in the middle and medium
items on top.
When loading wet items make
sure you set the load/water level
high enough to allow the items to
move freely.
Wash bulky items like blankets
separately.
To add items after washer has
started, push in Cycle knob and
submerge additional items next to
the agitator. Close the lid and pull
Cycle knob out to restart.
To reduce wrinkling, give
permanent press items, synthetics
and poly knits room to move freely
in the washer.
NOTE:
•
Do not wrap large items like sheets
around the agitator.
•
Do not wash fabrics containing
flammable materials (waxes,
cleaning fluids, etc.) in your washer.
Load
Leave the lid open after washing
to allow moisture to evaporate. The
wash basket is practically care free.
If you want to clean the washer use
a clean soft cloth dampened with
liquid detergent, then rinse. (Do
not use harsh or gritty cleaners.)
Fill Hoses—
Hoses connecting
washer to faucet should be replaced
every five years.
Moving and Storage—
Ask the service
technician to remove water from
drain pump and hoses. Contact
your local distributor for
information on how to keep the tub
stationary when moving the washer.
Long Vacations—
Be sure water
supply is shut off at taps. Drain all
water from hoses if weather will be
below freezing.
The Washer
Care & Cleaning
9
Page 10
Down-Filled Garments Always wash down-filled garments separately from other types
of garments. Wet down gives off an odor that will disappear when
the down is dried. Wash down items frequently to fluff up the
down and to retain down’s warmth. When washing make sure
the load is balanced. Add towels if necessary. Always tumble-dry
down garments.
Pillows Pillows are made from a variety of materials. Wash only if
recommended on the Pillow Manufacturer’s Care Label. Before
washing check pillows for weak seams or holes, and mend. Let
the washer fill with water and add detergent. Let the washer
agitate for several minutes and then add pillows in pairs. This
will keep the load balanced. Use the largest load/water level
available.
Blankets Let the washer fill with water, add detergent, allow detergent to
dissolve, then add blanket. Wash only one blanket at a time.
Permanent Press Clothes Select a larger load/water level than normal. This will provide
that are Line Dried more water to help reduce wrinkling and to allow clothes enough
room to move around. Remove clothes as soon as the wash cycle is
complete and hang them up immediately.
Heavy Loads The SUPER WASH cycle is specially designed for extremely
heavy loads. For normal load sizes, the REGULAR wash cycle is
recommended for optimum performance and water and energy
consumption. For best results, always follow the fabric
manufacturer’s care instructions.
If you have any questions, please call the Major Electrical
Appliances head office at 02-9825-9424.
10
Helpful Information
Specialty Care Guide
Item Suggested Care
Always follow Fabric Manufacturer’s Care Label or instructions when laundering.
Otherwise use the information below as a general guide.
Page 11
11
If Something Goes Wrong
Problem Possible Causes What to Do
Washer is unplugged • Make sure cord is plugged securely into a
working outlet.
Water supply is turned off • Turn both hot and cold taps fully on.
Controls are not set properly • Check controls and make sure Cycle knob
is pulled out to ON position.
Lid is open • Close lid and pull Cycle knob out to ON
position.
Circuit breaker/fuse is • Check house circuit breakers/fuses. Replace
tripped/blown fuses or reset breaker. Washer should have
separate outlet.
Washer Won’t Operate
Drain hose is kinked or • Straighten drain hose and make sure
improperly connected washer is not sitting on it.
• Top of drain outlet should be less than
1m (3 ft.) above floor.
Water Won’t Drain
Control is not set properly • Check water temperature control and adjust.
Water supply is turned off • Turn both hot and cold taps fully on and
or improperly connected make sure hoses are connected to correct
taps.
Water valve screens are • Turn off the water source and remove the
stopped up
water connection hoses from the upper back
of the washer. Use a brush or toothpick to
clean the screens in the machine. Reconnect
the hoses and turn the water source back on.
House water heater is not set • Make sure house water heater is delivering
properly water at 48°C.–65°C. (120°F.–150°F.).
Water Temperature
is Incorrect
Page 12
12
Problem Possible Causes What to Do
Fill hoses or drain hose is • Make sure hose connections are tight at taps
improperly connected and make sure end of drain hose is correctly
inserted in and secured to drain facility.
Household drain may
•
Check household plumbing. You may need
be clogged to call a plumber.
Constant water pressure to the • Tighten hoses at the taps and turn the water
fill hoses at the water source off after each use.
•
Check condition of the fill hoses; they may
need replacement after 5 years.
Water Leaks
Washer is uneven • Make sure washer is level and firm
to the floor.
Washer load is unbalanced • Push the Cycle knob in to stop the
washer, open the lid and redistribute
the load evenly. Close the lid and restart.
Shipping rod has not been • Remove the shipping rod on the bottom
removed right side of the washer just before sliding
the washer in place. Do not use the washer
with the shipping rod in place.
Water is draining • There will be a gurgling “sucking” sound
prior to the spin cycle. This is normal and
will stop as soon as the machine goes into
the spin cycle.
Washer is Noisy
The washer normally pauses
between washing steps
Washer Pauses
in Cycle
Incorrect cycle • Make sure the cycle selected matches the
selected load you are washing.
This is normal for some fabrics
Clothes too Wet
If Something Goes Wrong
Page 13
13
Problem Possible Causes What to Do
Incorrect sorting • Separate lint producers from
lint collectors.
Washing too long • Wash small loads for a shorter time than
larger loads.
Detergent not dissolving •
For best performance always add detergent
before adding clothes. If you use powdered
detergent, pre-dissolve
detergent in hot water
before adding to washer.
• Try a liquid detergent.
• Use warmer water temperature.
Overloading • Make sure load/water level setting matches
load size.
Too much bleach • Check bleach package for correct amount.
Not enough detergent • Try using more detergent.
Incorrect use of fabric softener • Check fabric softener package for
instructions (see Fabric Softener
Dispenser section).
Lint or Residue
on Clothes
Improper loads • Avoid mixing heavy items (like work
clothes) with light items (like blouses).
• Separate permanent press from
other laundry.
• Try a fabric softener.
Overloading or incorrect • Load your washer so clothes have enough
water level room to move freely.
Incorrect wash and dry cycles • Match Cycle selection to the type of fabric
you are washing (especially for permanent
press loads).
Repeated washing in water • Wash in warm or cold water with plenty
that is too hot of detergent.
Wrinkling
Page 14
14
If Something Goes Wrong
Problem Possible Causes What to Do
Some fabrics will naturally • Hot water is more likely to cause shrinkage
shrink in the wash than cold water.
• Follow directions on fabric care label.
Shrinkage
Pins, snaps, hooks, sharp • Fasten snaps, hooks, buttons, and zippers.
buttons, belt buckles,
• Remove loose items like pins, objects in
zippers, and sharp objects
pockets and sharp buttons.
left in pockets
• Turn knits (which snag easily) inside out.
Undiluted chlorine bleach • Check bleach package instructions for
proper amount.
• Never add undiluted bleach to wash or
allow clothes to come in contact with
undiluted bleach.
Small tears or holes • Repair tears and holes before washing.
present before wash
Chemicals like hair bleach, • Rinse items that may have chemicals
hair dye, permanent wave on them before washing.
solution and toilet bowl cleaners
Permanent press items • While this is not caused by the washer,
naturally fray (especially you can slow the fraying process by
collars and cuffs) washing small permanent press loads with
a higher load/water level setting.
• Avoid washing heavy items (like towels)
with permanent press items.
Snags, Holes, Tears,
Rips, or Excessive
Wear
Page 15
Problem Possible Causes What to Do
Not enough detergent • Try using more detergent (especially with
(larger loads, heavy soil, larger loads).
and hard water might
• If you live in a hard water area try using
require more detergent)
a water conditioner or install a water
softener.
Water is not hot enough • Make sure water heater is delivering water
at 48°C.–65°C. (120°F.–150°F.).
• Do not use the washer when hot water is
used for other needs (dishes, baths, etc.).
Washer is overloaded • Make sure load/water level setting matches
load size.
Soak time is too short • Soak at least 30 minutes.
Soaking with too little detergent • Use more detergent (especially with
heavy soil).
Detergent is not dissolving • Add detergent as wash basket fills with
water before you load clothes.
To restore grayed clothes, • Put clothes through a wash cycle using hot
try one of the following water. (Check the garment’s manufacturing
care label to see if hot water can be used.)
Add a non-precipitating water softener. Use
2 1⁄ 2 times more than is recommended
for normal water softening. Do not use
detergent or soap. Allow clothes to go
through a complete cycle. Repeat if
necessary.
• Soak your clothes using a water softener
instead of a soaking agent. Allow clothes
to soak for about 20 minutes.
Grayed Clothes
15
Page 16
16
Not enough detergent • Always use the recommended amount
on a consistent basis of detergent.
Chlorine bleach may yellow • Use non-chlorine bleach.
some fabrics
Iron or manganese in water may •
Use extra detergent plus a non-precipitating
cause yellowing or yellow spots water softener dissolved in water and
non-chlorine bleach.
• Run hot water for 2 minutes to help the
pipes clean out iron buildup.
• Drain your house water heater occasionally.
• To remove spots spread stain area over a pan
of boiling water and squeeze lemon juice
through the stain.
Yellowed Clothes
Incorrect use of fabric softener • Check fabric softener package
for instructions (see Fabric Softener
Dispenser section).
• To remove spots dampen the spots
and rub with undiluted liquid detergent.
Rewash, using chlorine bleach if it is safe
for the fabric.
Blue or Gray Spots
Type of detergent • Switch to a lower sudsing detergent brand
and follow instructions on package.
Very soft water • Try less detergent.
Too Many Suds
Result of normal wear on • While this is not caused by the washer,
poly-cotton blends you can slow the pilling process by washing
poly-cotton blends inside out.
Pilling
If Something Goes Wrong
Problem Possible Causes What to Do
Loading...