GE WNCJ2050D0WC, WNCK2050D0WC, WNCK2050D1WC, WNRD2050D1WC, WNRD2050DCWC Installation Guide
...
i i =ll = i i =• L •
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT - ObserveaH
governing codes and ordinances.
. Note to Installer- Be sure to leave these instructions
for the consumer's and local inspector's use.
, Skill revel - Installation of this commercial washer
requires basic mechanical and electrical skilrs. Proper
installation is the responsibility of the installer.
Product failure due to improperinstallation is not
covered underthe GEAppliance Warranty.
i i ii
IMPORTANT -I you,eceiveda
damaged commercial washer, you should immediately
contact your dealer or builder.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS
shown throughout these instructions.
Hit i= i ==n = i
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
IPub,No,31-t5558
[Dwg,No,143BB310P032
ND 658-04 (7/03)
Installation Preparation
i i i ] i
i i i i
TOOLS YOU WILL NEED:
Socketset
Slip]oint pliers
i i i i
INSTALLATION REQUIREMENTS:
LOCATION
Washer must be installed on firm flooring to minimize
vibration during spin cycles. Concrete flooring is
best, but wood base [ssufficient providedthat floor
support meets FHA standards. Washer should not be
installed on rugs or carpet, be exposed to weather or
temperatures below freezing.
ELECTRICAL AND PLUMBING
REQUIREMENTS
• FORPERSONAL SAFETYDO NOTUSE
AN EXTENSION CORDORADAPTER
PLUGWiTH THIS APPLIANCE.
WARNING
• DONOT,UNDERANY CIRCUM-
STANCE, CUTORREMOVETHETHIRD
GROUNDING PRONG FROMTHEPOWERCORD,
• FOLLOWNATIONAL ELECTRICCODEANSIINFPA
70 ORLOCALCODESAND ORDINANCES.
i i i i ii i
i.iq
i
PLUMBING
•Water Pressure-Must be 10 psi minimum to 150psi
maximum dynamJc pressLire measured at faucet.
•Water Temperature-Water heater should be set to
deliver water at 120°F to 150% (50°Cto 66°C)IN
THEWASHER when HOTwash is selected.
• Shutoff Valves-Both hot and cold shutoff valves
(faucets) should be supplied.
• Drain-Water may be drained into a standpipe or set
tub. The discharge height MUST NOT BE LESS
THAN 30INCHES nor more than 8feet above the
base of the washer. The standpipe must be 1-1/2
inches minimum inside diameter and must be open
to the atmosphere.
i i i
COUNTDOWN DISPLAY
(WCCD AND WLCD MODELS ONLY)
The countdown display shows the remaining time in
the cycle. The display board isconfigured properly at
the factory for the correct cycle timer installed in the
washer. If you wish to change the cycle timer, or add a
debit card interface to the washer, you will need to
change the configuration setting of the countdown
display board as follows.
ON
1 2 3 4
Switch Numbers---]
ELECTRICAL PREPARATION
This appliance must be supplied with 115V,60Hz,and
connected to an individual, properly grounded branch
circuit, protected by a 15or
20 amp circuit breaker or
fuse.
• If the electric supply
provided does not meet
the above specifications,
call a licensed electrician.
GROUNDING INSTRUCTIONS
This appliance must be
grounded. In the event of
malfunction or breakdown,
grounding will reduce the risk
of electric shock by providing
a path of least resistance
for electric current. This
appliance is equipped with a
cord having an equipment- AttachGroun_l
grounding conductor and a (ObtainLocally)
grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
If required, an external ground wire (not provided)
which meets local codes may be added. Attach to
washer cabinet with sheet metal screw (not provided)
to rear of washer as illustrated. The screw required is
a #8 sheet metal screw, 18 threads per inch, 1/2 inch
long. It can be obtained locally at any hardware store,
InsureProperGround
ExistsBefareUse
32 Minutes
25 Minutes
21 Minutes
Debit Card
i i
1 1 0 0 '
0 1
1 0 10 _
o 0
i
,_ WARNING: improper connection of the
equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician if
you are in doubt as to whether the appliance is
properly grounded.
iii
ii ii i
Loading...