GE WM7M Specification Sheet
GE
AREA LIGHTING
g
Lighting Solutions
GUIDE FORM SPECIFICATIONS
WALLMOUNT TM 175 LUMINAIRE
GENERAL DESCRIPTION
The totally enclosed, weather-resistant luminaire designated
_______ (identify) shall be a GE WALLMOUNTTM 175 luminaire,
ordering number _______ (specify WM7M or WM7S, plus ordering
number logic from catalog) or approved equal, to operate one
_______ (specify [(50, 70, 100 or 150[55V]) watt high pressure
sodium (HPS) or 175 watt metal halide mogul-base] or [(50, 70,
100 or 150 [55V]) watt HPS or (70, 100 or 175) watt metal halide
medium-base]) lamp from a nominal _______ (specify 120, 208,
240, 277, 347 or 480) volt, 60 Hertz power source. The luminaire
shall include a completely prewired integral ballast and an optical
assembly. The luminaire shall be UL/cUL Listed SUITABLE FOR WET
LOCATIONS. Standard construction is IP55. Ballast , housing, optical
and luminaire assembly shall all be from the same manufacturer.
MECHANICAL CONSTRUCTION
The luminaire shall include a die-cast aluminum housing and
side-hinged door with glass refractor sealed to it and providing
complete front access to ballast and lamp. The luminaire shall
have standard and vandal-resistant screws provided to secure the
refractor to the housing. Die-cast aluminum surfaces shall have
an electrocoat _______ (specify dark bronze or gray) paint finish.
Multiple junction box mounting patterns shall include provisions
for 3-¼-inch (83 mm) octagonal, 4-inch (102 mm) octagonal or
2-inch x 4-inch (51 x 102 mm) rectangular junction box and provisions for an optional knuckle wall mount or slipfitter. The luminaire
shall be mounted with 3/8-inch (9.5mm) bolts. There shall be a
knock-out for optional field-installed photoelectric control kit and
a .5-inch (13mm) threaded top conduit entrance.
BALLAST OPERATION
OPTICAL ASSEMBLY
Th e op ti ca l as se mb ly s ha ll h ave a “sna p- in ” an odized
al uminum reflect or with Alzak✝ fi ni sh, impact/h eat-resi stant tempe re d pris matic borosil icate re fractor and
a _______ (specify mogul base socket with superior lamp
gri pp ing , wit ho ut l amp [WM7 MXXXX XXXXX XXXX] or
medium base socket with HPS or metal halide lamp included
[WM7SXXXXXXXXXXXX]). The mogul base E39 socket shall have
added insulation, giving it the ability to handle the higher pulse
ratings of newer HID systems.
* REFER TO PRO DUCT PAGE FOR BALL AST S ELECTION.
FOR MORE DEFIN IT IV E INF OR MATIO N, R EF ER T O
B A L L AST S P E C I FI CAT IO NS I N T ECHNIC A L D ATA
SECTION.
The luminaire shall have a standard _______ (specify) ballast*. The
ignitor (for HPS only) and ballast shall be prewired to the lamp
socket requiring connection of power supply leads only. The ballast shall be in full compliance with lamp-ballast specifications
available to the fixture manufacturer from the lamp manufacturers
at the time of fixture manufacture.
The ballast shall reliably start and operate the lamp in ambient
temperatures down to -20°F for metal halide and -40°F for HPS.
Guide Form Specifications – 2011
g
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1 6 9 4 3 5 3 3- - -- 8 8 8
GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
Loading...