GE WCVH6800J4WW, WCVH6800J4MV, WCVH6800J4MS, WCVH6800J4MR, WCVH6800J4BB Owner’s Manual

...

GEAppliances.com

Safety Instructions ............. 2,s

Operating Instructions

Control Panels ...................... 4, 5

Control Settings ..................... 6, 7

Features ........................... 8-10

Loading and Using the Washer .... 10, 11

Cleaning the Washer ............. 12-14

Installation Instructions ..... 15-20

Preparing to Install Your Washer ...... 15

Rough-In Dimensions ................. 16

Location of Your Washer ............. 16

Unpacking Your Washer .............. 17

Drain Requirements .................. 18

Electrical Requirements ............... 18

Water Supplg Requirements .......... 18

Installing the Washer ............. 19, 20

Replacement Parts ................... 20

GFWN1000

WBVH5200 WBVH5300

WCVH6400 WCVH6800

WHDVH680

Troubleshooting Tips ......... 2t-24

Consumer Support

Warrantg ............................ 25

Service Telephone Numbers .......... 28

ENERGYSTAR

As an ENERGYSTAR®partner, GE has determined that this

product meets the ENERGYSTAR®

guidelinesforenergg efficiencg.

Write the model and serial

numbers here: Model # Serial #

Youcan find them on 6 label on the side of the washer.

49-90392

12/08/09 GE

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING! or.,,our in,:ormo ionin ,ismon.o mus minimi ris,

of fire or explosion, electric shock, or to prevent property damage, personal injury or loss of life.

Theinstructions in this manual and all other literature included with this washer are

not meant to cover every possible condition and situation that may occur. Good, safe practices and caution MUSTbe applied when installing, operating and maintaining any appliance.

WATER HEATERSAFETY

Undercertain conditions,hydrogen gas may beproduced ina water heaterthat has not beenused for two weeks

or more.Hydrogen gas can be explosiveunder thesecircumstances.

Ifthe hot water hasnot beenusedfor two weeksor more,prevent the possibilitgof damage or injurgbg

turning on all hot water faucets and allowingthem to run for severalminutes. Dothis before usingang electrical appliance which isconnected to the hot water sgstem.Thissimple procedurewill allow ang built-up hgdrogen

gas to escape.Sincethe gas isflammable, do not smoke or usean open flameor applianceduring this process.

PROPERINSTALLATION

Thiswasher must beproperly installedand located inaccordance with the InstallationInstructions beforeit is used.

[] Installor storewhere itwill not beexposed [] Properlyground washerto conformwith allgoverning

to temperaturesbelowfreezingor exposed codesand ordinances.Followdetailsin Installation to the weather,which couldcausepermanent Instructions.

damage andinvalidatethe warranty.

YOURLAUNDRYAREA

[] Keepthe area underneath and around gout

appliances free of combustible materials such as lint, paper,rags and chemicals.

[] Do not leave the washer door open.An open door

could enticechildren to hang on the door or crawl insidethe washer.

[] Closesupervision isnecessarg ifthis appliance is

used bgor near children.Do not allow children to plag on,with or inside this or ang other appliance.

Usethis appliance

onlyfor its intended

purposeas describedin

this Owner's Manual.

WHEN USINGTHEWASHER

[]

Never reach into washer while it is moving. Wait until the machine has completelg stopped

before opening the door.

[]

Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce a toxic gas which mag cause death.

[]

Do not wash or drg articles that have been cleaned in, washed in, soaked in or spotted with combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, drg-cleaning solvents, kerosene, etc.) which mag ignite or

explode. Do not add these substances to the wash water. Do not use or place these substances

around gour washer or drger during operation.

[]

The laundry process can reduce the flame retardancg of fabrics. To avoid such a result, carefullg follow the garment manufacturer's wash and care instructions.

[]

To minimize the possibilitg of electric shock, unplug this appliance from the power supplg or disconnect the washer at the building's

distribution panel bg removing the fuse or switching off the circuit breaker before

attempting ang maintenance or cleaning. NOTE: Pressing the power button does NOT disconnect

the appliance from the power supplg.

GEAppliunces.com

Never attempt to operate this appliance if it isdamaged, malfunctioning, partially

disassembled, or has missing or broken parts, including a damaged cord or plug.

Do not slam the washer door closed. Do not trg to force the door open when locked (LOCKED

indicator ON).This could result in damage to the washer.

Thewasher isequipped with an electrical overload protector. The motor will stop

if it becomes overheated. The washer will automaticallg restart after a cool-down

period of upto 2 hours, if the washer has not been manuallg turned off

during this time.

WHEN NOT IN USE

Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if

a break or rupture should occur. Check the condition of the fill hoses; GErecommends

changing the hoses everg 5 gears. Before discarding a washer, or removing it

from service, remove the washer door to prevent children from hiding inside.

[] Do not attempt to repair or replace any part of

this appliance unless specifically recommended

in this Owner's Manual, or in published user-repair instructions that gou understand and have the

skills to carrg out.

[] Do not tamper with controls.

READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVE THESE INSTRUCTIONS

About the washer control panel.

Find the illustration that closely matches your mode! and see the cycle descriptions starting on page 6 for details.

(Onsome

models)

WASH TEPIP

o •

HOT

COrD

TAPCOLD

GEAppliances.com

• •

About the washer control panel.

Power

press to "wake up" the displag. Ifthe displag is active, press to put the washer into standbg mode.

NOTE: Pressing POWER does not disconnect the appliance from the power supply.

Wash Cycles

The wash cgcles are optimized for specific tgpes of wash loads. The chart below will help gou match the wash setting with the loads. The GentleCleaff _ lifters lightlg tumble the clothes into the water and

detergent solution to clean the load.

WHITES For heavilg to lightlg soiled white cottons, household linens, work and plag clothes.

COLORS/NORMAL For heavg to lightlg soiled colorfast cottons, household linens, work and plag

clothes.

STAINWASH For heavg soiled colorfast cottons, household linens, work and plag clothes.

EASYCARE Forwrinkle-free and permanent press items.

(PERMAPRESS}

(some models)

ACTIVEWEAR For active sports, exercise and some casual wear clothes. Fabrics include modern

(some models) technologg finishes and fibers such as spandex, stretch and micro-fibers.

DELICATES For lingerie and special-care fabrics with light to normal soil. Provides gentle

(some models) tumbling and soak during wash and rinse.

HANDWASH For items labeled hand-washable with light soils. Provides gentle rocking to mimic

the handwashing action.

WASHABLE Forthe washing of machine washable wool products, provided that theg are

WOOLS washed according to the instructions on the garment label. When selecting this

(some models) cgcle, gou must use a detergent suitable for washing wool.

MY CYCLE Pressto use, create or modifg custom wash cgcles.

(some models)

SPEEDWASH For lightlg soiled items that are needed in a hurrg. Cgcle time isapproximatelg

30 minutes, depending on selected options.

DRAIN & SPIN Drain and spin at any time.

RINSE& SPIN To quicklg rinse out ang items at ang time.

GEAppliances.com

Soil Level

Changing the SOIL LEVELincreases or decreases the wash time to remove different amounts of soil.

To change the SOIL LEVEL,press the SOIL LEVEL button until gou have reached the desired setting.

Spin Speed

Changing the SPIN SPEEDchanges the final spin speed of the cgcles. Alwags follow the fabric manufacturer's care label when changing the SPIN SPEED.

To change the SPIN SPEED,press the SPIN SPEED button until gou have reached the desired setting.

Higher spin speeds are not available on certain cgcles, such as Delicates. Higher spin speeds remove more water from the clothes and will help reduce drg time, but mag also

increase the possibilitg of setting wrinkles on some fabrics.

Wash Temp

Adjust to select the proper water temperature for the wash cgcle. The prewash and rinse water is

alwags cold to help reduce energg usage and reduce setting of stains and wrinkles. Follow the fabric manufacturer's care label when selecting the wash temperature.

To change the wash temperature, press the WASH TEHP button until gou have reached the desired

setting. The Sanitized wash temperature is not available on certain cgcles, such as Delicates.

When selecting the Sanitizewash temperature (on some models), the washer increases the water temperature to sanitize and kill more than 99% of mung common bacteria found in home laundrg. The

sanitize wash temperature is onlg available on Stain Wash and Whites wash cgcles. For best results, select

the heavg soil setting when using the Sanitize wash temperature setting.

NOTE: The first !0 seconds of the wash fill is always cold. This feature assists in conditioning the fabric and preventing stains from setting on garments.

START/PAUSE

Pressto start o wash cgcle. If the washer is running, pressing it once will pause the washer and unlock

the door. Pressagain to restart the wash cgcle.

NOTE:If the washer is paused and the cycle is not restarted within 2 hours, the current wash cycle will

be cancelled. NOTE:The washer performs automatic system checks after pressing the STARTbutton. Water will flow

in 45 seconds or less. You may hear the door lock and unlock before water flows; this is normal.

About the washer features.

NOTE:Features may not be available on all washer models.

Cycle Signal

Usethe SIGNALbutton to change Pressthe button until gou reach

the volume ofthe end ofcgcle signal, the desired volume.

Prewash Ion some models)

Prewashisan extra wash before

the main wash. Useit for heavilg soiled clothes orfor clothes with a care label

that recommends prewashing before washing. Besureto add high-efficiencg

Extra Rinse

Usean extra rinsewhen additional rinsing isdesiredto remove excessdirt and

detergent from soiled loads.

Delay Start (on some models)

Youcan delagthestart of awash cgcle

for 10-18 hours,depending onthe model.

Pressthe DELAYSTARTbutton to choose

the numberof hours gou want to delag the start of the cgcle,then pressthe START

button.The machine willcount down and

start automaticallg at the correct time.

detergent, or the proper wash additive

to the prewash dispenser.

NOTE:When selecting prewash, it is recommended to use powder

detergent in the main wash (detergent) compartment.

NOTE:Ifyou forget to fullyclosethe door, a reminder signalwill beepremindingyou

to do so. NOTE:Ifyou open thedoor when the delay

iscounting down, the machine willenter thepause state.Youmustclosethe door

and pressSTARTagain in orderto restart thecountdown.

Lock

Youcan lock the controls to prevent ang selections from being made. Orgou can

lockthe controls after gou have started

a cgcle. Children cannot accidentally start

the washer by touching pads with this option selected.

To lockthe washer, pressand hold the DELAYSTARTbutton for 3 seconds

(onsome models useSIGNALbutton).

To unlockthe washer controls, press

and hold the DELAYSTARTbutton for 3 seconds.

Thecontrol lock icon on the displagwill

light up when it is on.

HOLD 3 SECSTO LOCK & UNLOCK

CONTROL PANEL

NOTE:The POWERbutton can still be used when the machine is locked.

MY CYCLE (on some models)

ii_iii_iiill_I i__ !_ ii_i_

Tosavea favoritecgcle,setthe desired settingsforwash cgcle,soillevel,spinspeed

and washtemp settingsand holddownthe

NOTE: When using MY CYCLE, wash options cannot be modified after the

cycle has been started.

MYCYCLEbutton for3 seconds.Abeepwill soundto indicatethecgclehas beensaved.

NOTE:If you change wash options with

MYCYCLEbefore starting the cycle, the

To usegour custom cgcle,pressthe MYCYCLEbutton beforewashing a load.

MYCYCLElight will turn off and you will

be returned to the base cycle.

Tochange the saved cgcle,set the desired settings and hold down the MYCYCLE

button for 3 seconds.

BASKET CLEAN

BasketClean isa cgcle that freshens up

the insideof gour washer. The cgcle uses

bleachor other availablewashing machine cleanersand morewater to

once evergmonth to reduceodor and residuebuildup insidethe washer.

Formore information on BasketClean, referto the Careand Cleaningsection on page 12.

refresh gout washer. UseBasketClean

The Dispenser Drawer

Slowlyopen the dispenser drawer by pulling it out until it stops.

After addinglaundry products,slowly dose

thedispenserdrawer.Closingthe drawer too

quicklycouldresultin earlydispensingof the bleach,fabricsofteneror detergent.

ThePrewashCompartment(onsomemodels)

i Only usethe PrewashCompartmentifyou

are selectingthe Prewashcyclefor heavily soiledclothes.Add measureddetergentor

prewashadditiveto the backleft prewash

compartment of the dispenserdrawer.

[] Detergentor prewashadditive isflushed

from thedispenserinthe prewashcycle (ifselected).

GEAppliances.com

Youmay seewater in thebleachand fabric softenercompartmentsat theendof thecycle.

Thisis aresultofthe flushing/siphoningaction and is part of thenormaloperationof the

washer.

NOTE:Liquiddetergentwill drain intothe washerdrumas itis added.

[] Detergentusagemay needto be adjusted

for watertemperature,water hardness,size and soil levelofthe load.Avoid usingtoo

muchdetergent inyour washerasit can lead

to oversudsinganddetergent residuebeing

lefton the clothes.

Pew@Detergent

NormalHEL Det_

2XHELiquid

DetergentSetting{

Imostcommon setting),,

3XHE Lic

Deterge

Settin(

Appearancemayvary

Onsomemodels,theLiquidBleach Compartmentisinthecenter.

The Detergent Compartment

[]High-efficiency detergent is required

for this washer. Usethe detergent

manufacturer's recommendedamount.

Thedetergentselectioninsertmust beplaced

inthe detergentcompartment in a specific positionaccordingto what type ofdetergent

you areusing. m PowderDetergent-Placethe insert

in the rear position.ThePowderIcons_ mustline up oncenter when the insert

isinthe powderposition.

[] Liquid Detergent- Youwill needto adjust

the insertaccordingto the type ofLiquid

Detergentyou are using.The iconson the sideof the detergentcompartment must line up onthe center whenthe insertisin position.

NOTE:Not allmodels have the 2x and 3x detergentsettings.Some have only regular

HEdetergentsettings. Youmust reducethe amount of detergent for 2x or 3x detergent

per bottleinstructions.

The Liquid Bleach Compartment

IMPORTANT:The bleach compartment

position varies by model.Besure to identify

thecorrect compartment for bleach before using.

tf desired,measureout the recommended amount of liquid bleach,not to exceed

1/5 cup(80ml),and pourinto the center compartment labeled"LIQUIDBLEACH"

markedwith this symbol,/_,.

Hovethe insertby pullingit upand replace it bysliding itdown betweeneither the rear

or front detergent compartment moldedrails, asdesired,for powder or liquiddetergent.

[] Add measureddetergent to thefront left

detergent compartment ofthe dispenser drawer.

[]

Detergentis flushedfrom the dispenser

at the beginningof thewash cycle.Either

powderedor liquiddetergent can be used.

[]

Detergentusage may needto beadjusted for watertemperature,water hardness, sizeand soil levelof the load.Avoidusingtoo

muchdetergent in your washeras itcan lead to oversudsingand detergent residuebeing

left onthe clothes.

[] Usingmore detergent than the

recommendedquantity cancause

residuebuildupon your washer.

Donot exceedthe maximumfill line.Overfilling cancauseearlydispensingof the bleach which

couldresultin damagedclothes. NOTE:Do notusepowderedbleachin the

dispenser.

Onsomemodels,theLiquidBleach Compartmentisontheright. 9

About the washer features.

The Fabric Softener Compartment

IMPORTANT:The fabric softener compartment position varies by model. Be sure to identify

the correct compartment for fabric softener

beforeusing.

tf desired,pour the recommendedamount of liquidfabric softener into the comportment

labeled"FABRICSOFTENER."

Onsomemodels,theFabricSoftener Compartmentisontheright.

Onsomemodels,theFabricSoftener Compartmentisinthecenter.

Loading and using the washer.

Useonly liquidfabric softener inthe dispenser.

Dilutewith water to themaximum fill line. Donot exceedthe maximumfill line.Overfilling

cancauseearlydispensingof the fabric softener

which could stain clothes.

NOTE:Do notpour fabricsoftener directly on the wash load.

Always follow fabric manufacturer's core label when laundering.

Sorting Wash Loads

Sort laundry into loads that can be washed together.

Colors Soil Fabric Lint

Whites Heavy Delicates Lint Producers

Lights Normal Easy Care Lint Collectors Barks Light Sturdy Cottons

[] Combine large and small items in a load. Load large items first. Large items should not be more than

half the total wash load.

[] Washing single items is not recommended. This may cause an out-of-balance load. Add one or two

similar items.

[] Pillows and comforters should not be mixed with other items. This may cause an out-of-balance load.

Pre Clothes

[] To avoid snags during washing.

Follow these steps to maximize garment care.

Closegarment zippers, snaps, buttons and hooks. Mend seams, hems, tears.

Empty all items from pockets. Remove nonwashable garment accessories such as ornaments and nonwashable trim materials.

[] To avoid tangling, tie strings, draw ties and belt-like materials. [] Brush away surface dirt and lint; treat spots and stains. [] Promptly wash wet or stained garments to maximize results. [] Mix garments using recommended maximum load sizes on page !!. [] Use nylon mesh garment bags to wash small items.

[] Wash multiple garments at one time for best results.

Loading the Washer

GEAppliances.com

Wash drum may be fully loaded with loosely added

items. Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etcJ.

Maximum Lauding Sizes*

WORKWEAR

4 Jeans

5 Workwear Shirts 5 Workwear Pants

LINENS

2 Bath Sheets

10 Bath Towels/

12 Washcloths

7 Hand Towels/

2 Terrycloth

Bath Mats

2 Flat Queen-Sized

Sheets

2 Fitted Queen-

Sized Sheets

4 Pillowcases

MIXEDLOAD

4 Pillowcases

2 Hand Towels

2 Flat Sheets/

2 Fitted Sheets 2 Bath Towels/

4 Washcloths

6 Shirts (Men's

or Women's)

4 Pair Pants

or Twills)

5 T-Shirts

7 Pairs of Boxers

4 Pairs of Shorts

6 T-Shirts 4 Pairs of

Sweatpants

4 Sweatshirts

2 Hoodies

7 Pairs of Socks

To add items after washer has started, press START/PAUSEand wait until the door is unlatched.

The washer may take up to 30 seconds to unlock the door after pressing START/PAUSEdepending

on the machine conditions. Do not try to force open the door when it is locked. After the door unlocks,

open gently. Add items, close the door and press START/PAUSEto restart.

SPEEDWASH

DELICATES**

7 Bras

7 Panties

3 Slips

2 Camisoles

4 Nightgowns

(Khakis

(2-4 GARMENTS}

2 Casual Wear

Work Shirts

! Pair Casual Wear

Work Pants

3 Soccer Uniforms

*Exceeding maximum recommended load sizes may affect cleaning performance and garment care.

**Using a nylon mesh bag for small items is recommended.

Cleaning the washer.

Careand Cleaning

Exterior: ImmediatelLl wipe off anLl spills. Wipe with damp cloth. Do not hit surface with sharp objects. Moving and Storage: Ask the service technician to remove water from drain pump and hoses.

Do not store the washer where it will be exposed to the weather. When moving the washer,

the tub should be kept stationurg bLlusing the shipping bolts removed during installation. See Installation Instructions in this book. If these parts are not available, theg can be ordered

bg visiting our Website at GEAppliunces.com or bg calling 800.GE.CARES. Long Vacations: Be sure the water supplg is shut off at the faucets. Drain all water from the hoses if the

weather will be below freezing.

Cleaning the interior of the Washer

To clean the interior of the washer, select the BasketClean feature on the control

panel. The cgcle will use more water, in addition to bleach, to refresh gout

washer.

NOTE:Readthe instructions below completelLl before starting the

BasketCleancgcle.

1. Remove any garments or objects from the washer and ensure the washer

basket is emptLl.

2. Open the washer door and pour

one cup or 250 ml of liquid bleach or other washing machine cleaner

into the basket.

. Close the door and select the

BasketClean cgcle. Pushthe START button.

4. When the BasketClean cLlcle is working, Llouwill see CLn on the

displuLl.The cLlclewill complete in about 90 minutes. Do not interrupt

the cLlcle.

5. After the cgcle is complete, leave the door open slightlLl for better

ventilation.

If for anLlreason the cLlcle needs to be interrupted, the door will not open

immediatelLl. Forcing open the door at

this stage mall cause water to flood. The door will open after the water is

drained to a level where it would not

flood the floor.

BasketClean mall be interrupted bll pressing the START/PAUSEbutton in between cllcles. A power outage in

the house might also interrupt the cllcle. When the power supplll is back, the

BasketClean cllcle resumes where it had stopped. When interrupted, be sure to run

a complete BasketClean cllcle before using the washer. If the POWER button

is pressed during BasketClean, the cllcle

will be lost.

IMPORTANT:

[] Run BasketClean with 1 Cup

(250 ml) of bleach once a month.

[] After the completion of a BasketClean

cllcle, the interior of llour washer mall have a bleach smell.

[] It is recommended to run a light color

load after the BasketClean cllcle.

Pour spout

Cleaning the Pump Filter

Due to the nature of the front-load washer, it issometimes possible for small articles

to pass to the pump. The washer has a filter to capture lost items so they are not

dumped to the drain. To retrieve lost items, clean out the pump filter.

1. Using a coin or flat screwdriver in the notch on the door, open

the access door.

2. Place a shallow pan or dish under

the pump access door and towels

on the floor in front of the washer to protect the floor. It is normal to catch

about a cup of water when the filter is removed.

3. Pull down the pour spout.

GEAppliances.com

Pump

Turn the pump filter counterclockwise

and remove the filter. Open slowly to

allow the water to drain.

Clean the debris from the filter.

Replace the filter and turn clockwise.

Tighten securely.

7. Flip up the pour spout.

8. Close the access door.

Cleaning the Door Gasket

Open the washer door. Using both hands, press down the door gasket. Remove any

foreign objects if found trapped inside the gasket. Hake sure there is nothing

blocking the holes behind the gasket.

While holding down the door gasket,

inspect the interior gasket by pulling it down with your fingers. Remove any

foreign objects if found trapped inside this gasket. Hake sure there is nothing

blocking the holes behind the gasket.

When you are finished cleaning the door gasket, remove your

hands and the gasket will return

to the operating position.

Cleaning the washer,

Locktabisvisible onlyafter drawer

hasbeenpulledout

Dispenser Drawer Area: Detergent and fabric softener mag build up in the dispenser drawer. Residue should be removed once or twice a month.

[] Remove the drawer bg first pulling it out until it stops. Then reach back into

the left rear corner of the drawer cavitg and press down firmlg on the lock tab, pulling out the drawer.

I Remove the inserts from the bleach and fabric softener compartments and

the detergent insert. Rinsethe inserts and the drawer with hot water to remove traces of accumulated laundrg products.

[] To clean the drawer opening, use a small brush to clean the recess. Remove

all residue from the upper and lower parts of the recess.

[] Return inserts to the proper compartments. Replace the dispenser drawer.

Installati

her

I structi

j If you hove any questions, call 800.GE.CARE5(800.452.2757) orvisitour Website at:6EApplionces.com J

BEFORE YOU BEGIN

Read these instructions completely and carefully.

. IH PORTANT - Savetheseinstructions

for local inspector's use.

" IM PORTJ_NT - Observe all governing

codes and ordinances,

. Note to Installer - Be sure to leave these

instructions with the Consumer.

, Note to Consumer - Keepthese instructions

for future reference.

, Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

, Completion time - 1-3 hours , Proper installation isthe responsibility of the installer. , Product failure due to improper installation is not

covered under the Warranty.

FOR YOUR SAFETY:

-_kWARNING

TOOLS REOUIRED FOR WASHER INSTALLATION

[] !/4" nut driver

[] 3/8" socket with ratchet [] 3/8" open-end wrench [] Adjustable wrench or 7/!6" socket with ratchet

[] Adjustable wrench or 9/!6" open-end wrench [] Channel-lock adjustable pliers

[] Carpenter's level

PARTS SUPPLIED

[] CableTie

[] Water Hoses(2)

, This appliance must be properly grounded and

installed as described in these Installation Instructions.

, Do not install or store the appliance in an area where

it will be exposed to water/weather. Seethe Location of Your Washer section.

NOTE:This appliance must be properly grounded, and electrical service to the washer

must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70.

[] HoseGuide

STACK BRACKET KIT

A stack bracket kit is available at additional cost.

It can be ordered inthe United States by visiting

our website at GEAppliances.com or calling

800.GE.CARES.Order kit #WE25X!00!8 or GEFLSTACK.

Installation Instructions

LOCATION OF YOUR WASHER

Do Not Install the Washer:

1.In an area exposed to dripping water or outside weather conditions. The ambient temperature should

never be below 60°F (15.6°C)for proper washer operation.

2.In an area where it will come in contact with curtains or drapes.

3.On carpet. The floor MUSTbe a hard surface with a maximum slope of 1/2" per foot (1.27cm per 30 cm).To make sure the washer does not vibrate

or move, you may have to reinforce the floor.

NOTE:If floor is in poor condition, use 3/a" impregnated plywood sheet solidly attached to the existing floor

covering.

IMPORTANT:

Minimum Installation Clearances

. When installed in alcove: Sides, Rear,

Top = 0" (0 cm)

, When installed in closet: Sides, Rear,

Top = 0" (0 cm), Front = 1" (2.54 cm)

• Closet door ventilation openings required: 2 louvers each 60 square in. (387 cm2),located 3"

(7.6cm) from top and bottom of door

ROUGH-IN DIMENSIONS

FRONT

27.0"

._ (68.6cm) _-

20.4"(51.9cm) _l

ELECTRONICTRANSPARENTVBOR_1

%_ ® OOo J

SIDE

3&6"

(772 cm)

2.2"

(5.6cm)

40.6"*

(103.1cm)

1,6"

_" (3.9cm)

*NOTE:With pedestal,62.6"

Stacked,84"

........................................[ t ......

40.6"*

(103.1cm)

39.1"

(99.2crn)

+ 36 hidden pages