GE UM5 Specification Sheet

GE

INDOOR LIGHTING

g

Lighting Solutions

GUIDE FORM SPECIFICATIONS
UNIMOUNT® 400 LUMINAIRE

LOW BAY ENCLOSED

GENERAL DESCRIPTION

The complete luminaire designated _____ (identify) shall be
a _____ GE UNIMOUNT® 400 luminaire, ordering number
_____(specifyUM5 or UM5W, plus ordering number logic from
catalog) or approved equal, to operate one _____ (specify [200,
250 or 400] watt high pressure sodium [HPS], [250 or 400] watt
metal halide, [320, 350 or 400] watt pulse start metal halide
or 400 watt mercury) lamp from a nominal _____(specify 120,
208, 220, 240, 277, 347 or 480) volt 60 Hz or (220, 230, 240 or

380) volt 50 Hz power source. The luminaire shall include a
completely prewired integral ballast and an optical assembly
with _____ (specify 1.5, 1.6, 1.7 or 1.9 according to photometric
selection table) IES Spacing Criterion (SC). The luminaire shall
be suitable for continuous service indoors in a maximum ambi­ent temperature of _____ (specify 55o or 65oC ). The
luminaire shall be UL Listed SUITABLE FOR DAMP LOCATIONS
and C-UL (Canadian) Listed for Indoor Locations. Standard con­struction is IP52. Units with W (Wet Location) option are IP54..

MECHANICAL CONSTRUCTION

For ease of installation and to facilitate maintenance and re­placement, the luminaire shall be supplied as components —
ballast and optical.

The ballast housing and optical assembly shall be provided
with easy-to-read moisture-resistant nameplates which can be
seen without disturbing the installed luminaire. All ballast and
optical assemblies shall include provisions for optional field
mounting of safety chains.

The ballast housing and mounting plate, shall be made of die­cast aluminum. The ballast housing shall have an electrocoat
gray paint finish.

A heavy duty mogul base socket with superior lamp gripping
shall be mounted to the ballast housing. The socket shall have
the ability to handle the higher pulse ratings of newer HID
systems.

To facilitate mounting, the luminaire shall have separate light­weight mounting components that can be easily removed from
the ballast housing and assembled to the structural or mount­ing hardware prior to mounting of the remainder of the lumi­naire. The mounting device must provide a positive vibration­resistant locking means including a set screw.

The wiring access cover plate and all screws requiring removal
during normal conduit mounting and/or wiring shall be captive.

The Ballast housing shall incorporate GELS EZ Connect™
plug-in wiring harness that provides for easier wiring
installation and quick replacement.

EZ Connect™ plug-in wiring harness shall enable the use of
*GELS Critique™ plug-in luminaire diagnostic test device.

BALLAST OPERATION

The luminaire shall contain a standard _______ (specify
Autoreg) type ballast* in full compliance with lamp-ballast
specifications available to the fixture manufacturer from the
lamp manufacturers at the time of fixture manufacture.

The ballast shall reliably start and operate the lamp in
ambient temperatures down to -20
halide or -40oF for HPS.

The luminaire and ballast shall be from the same
manufacturer.

o

F for mercury and metal

OPTICAL ASSEMBLY

Mounting of the optical assembly to the ballast assembly must
be secured by positive vibration-resistant means.

The optical assembly shall be enclosed and gasketed. The re­fractor shall be _______ (specify UV stabilized injection molded
prismatic heat-resistant acrylic or polycarbonate resin) for low
brightness. It shall be hinged and latched for lamp access and
no-tool relamping. The stainless spring steel door latches shall
be over-center, vibration-resistant type providing a spring-like
clamping action to the gasket.

The large diameter optical assembly shall dissipate heat and
provide precise light control for all high intensity
discharge (HID) light sources. The textured aluminum reflector
shall have an Alzak
the reflector shall be painted white (U4MW).

* REFER TO PRODUCT PAGE IN GELS PRODUCT CATALOG FOR
OTHER BALLAST SELECTIONS AND CRITIQUE™ DIAGNOSTIC TEST
DEVICE CAPABILITY. FOR MORE DEFINITIVE ELECTRICAL INFOR­MATION, REFER TO BALLAST SPECIFICATIONS IN TECHNICAL
DATA SECTION.

✝

finish on all surfaces (U4M) or the inside of

Guide Form Specifications – 2011

g

GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com

1 6 9 4 3 5 3 3- - -- 8 8 8

GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.