GE Trivection JT930, Trivection JT980, Trivection ZET3038, Trivection ZET3058 Installation Instructions Manual
Ilnstallation
nstructions
30" Built-In Trivection TM
Wall Oven
JT930, JT980, ZET3038, ZET3058
I I'_'1 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com I
BEFORE YOU BEGIN
Read these instructions completely
and carefully,
• IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT - Observeall
governing codes and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these
instructions for future reference.
• Skill level - Installation of this appliance
requires basic mechanical and advanced
electrical skills.
• Completion time - 1 to 3 hours
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
-&WARNING - This appliance must
be properly grounded.
• ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT
permitted on these products.
FOR YOUR SAFETY:
• Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F) generated
by the oven.
_i WARN ING: Theelectricalpowerto
the oven supply line must be shut off while
line connections are being made, Failure to
do so could result in serious injury or death,
• To prevent damage to the door and to
prevent excessive microwave leakage, do
NOT remove the door on the single wall
oven or the upper oven door on the double
wall oven.
229c4053P546-2
31-10557-2 04-04 JR
Installation Instructions
PREPARE TO INSTALL THE OVEN
TOOLS YOU WILL NEED
Drill with 1/8" Bit
(Extension may be
required)
Safety Glasses
Adjustable Wrench
(for 1-7/16" Nut)
Straight Edge or
Square
Pencil
Phillips Screwdriver
Level
Tape Measure
Hand or Sabre Saw
Gloves
PARTS INCLUDED
Metal
Bottom Trim
12 Screws
Plastic
Bottom Trim
OR
Metal Bottom
Trim Assembly
MATERIALS YOU MAY NEED
Strain Relief Junction Box Wire Nuts
Clamp for 1/2"
conduit
60" of String for Single Ovens
96" of String for Double Ovens
2
Installation Instructions
Ill PRE-INSTALLATION
All installation information on the following
pages is to be used for SINGLE and DOUBLE
oven installation!
[] Remove packaging materials. Check
behind hinges. Remove plastic on trims
and panel, all tape around the oven and
any shipping screws securing the oven
to the base pad. Use caution when lifting
the oven forward; the ovens are front
heavy.
_D DD
OB_E_ OD
A =
Broiler Pan
and Grid
Oven Racks
_ iterature
Pack
[] Open oven door and remove literature
pack, broiler pan and grid and oven
racks.
[] Remove Installation Instructions from
literature pack and read them carefully
before you begin.
[] Be sure to place all literature, Owner's
Manual, Installation Instructions, etc.
in a safe place for future reference.
Ill PRE-INSTALLATION (CONT.)
NOTE: To prevent damage to the door and
to prevent excessive microwave leakage, do
NOT remove the door on single wall oven
models or the upper oven door on double
wall oven models.
[] The lower oven door on the double
wall oven may be removed as an added
convenience during installation.
See Step 4.
DO NOT LIFT THE OVEN BY THE HANDLE!
[]
[]
Place the oven on a table or platform
even with the cutout opening. (Platform
must support 225 Ibs. single, 375 Ibs.
double.)
Remove the bottom trim from the top
of the oven. It will be installed at the end
of the installation process.
3
Installation Instructions
SINGLE BUILT-IN OVEN CUTOUT OPTIONS
CUTOUT OPTIONS FOR SINGLE
BUILT-IN OVENS
Skip to Step 3 for Double Built-In Oven models.
There are 4 installation options for single built-in ovens.
Choose the appropriate one for your application:
[] WALL MOUNTiSINGLE BUILT-IN OVEN OPTION
[] WALL MOUNTiSINGLE BUILT-IN OVEN BELOW
AN ADVANTIUM TM OVEN OPTION
[] WALL MOUNTiSINGLE BUILT-IN OVEN ABOVE
A WARMING DRAWER OPTION
[] UNDER COUNTERiSINGLE BUILT-IN OVEN
OPTION
[] WALL MOUNT--SINGLE BUILT-IN OVEN
OPTION
All corners must
be cut square
-....
Allow 11/16"--..9_
on sides for
overlap of oven
beyond cutout
_j 21" _3v_
Allow a minimum of
21" for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
3
Cutout Width
28 1/2" Min
_28 5/8" Max. a
Opening
between
inside walls
must be at
Least 28 1/2"
Wide
Allow 1" minimum
at top and 1 1/4"
minimum at bottom
"for overlap of oven
beyond cutout
Cabinet
Width 30"
/2"
Required Junction
Box Area
Cutout Height _2'27 1/4" Min.
-27 5/16" Max.
Recommended
cutout location
from floor
32 1/2"
Cabinet Width
Recommended
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
30"
32 1/2"
23 1/2" Min.
28 1/2" Min.
28 5/8" Max.
27 1/4" Min.
27 5/16" Max.
[] WALL MOUNT--SINGLE BUILT-IN OVEN
OPTION (CONT.)
NOTE: If the cabinet does not have a front
frame and the sides are less than 3/4" thick,
shim both sides equally to establish the
cutout width.
If the cabinet does not have a solid bottom,
two braces or runners must be installed level
with the bottom of the cutout to support the
weight of the oven. For single ovens, the
runners and braces must support 225 Ibs.
The solid bottom or runners must be level
with the bottom of the cutout, or the bottom
trim may not install correctly and then
interfere with the door opening.
equivalent
runners
level with
bottom of
cutout
Suitable
Bracing to
Support
Runners
-f---_Ove 21 5/8"-----_
r Centerline \
of Cabinet
NOTE: This oven is not approved for
stackable or side by side installation.
4
Installation Instructions
[] WALL MOUNT--SINGLE BUILT-IN OVEN
BELOW AN ADVANTIUM OVEN OPTION
30"_-_ 24"
I Mt n_-_
Construct
solid bottom
min. 3/8"
plywood
supported
by2x4or
1 x 2 runners,
all four sides
2" Min.
• When installed over a single wall oven,
allow at least 2" between the two openings.
This separation will provide clearance for
bottom overlap of the Advantium oven and
top overlap of the single wall oven.
• If you are replacing a GE/Monogram electric
double oven with the combined installation
of an Advantium and single wall oven, the
middle rail separating the two openings
may need to be larger than the 2" min.
shown.
• Always maintain 36 3/4" min. distance from
the floor to the Advantium oven cutout in
any installation combination.
• When installed in combination with a
GE/Monogram single wall oven, use
separate electrical junction boxes.
• Refer to Advantium oven installation
instructions for electrical requirements and
installation details of that product.
• Advantium ovens are approved for
installation above only certain specified
wall oven models. See the label attached
to the top of the oven for approved
Advantium oven models.
5
[] WALL MOUNT--SINGLE BUILT-IN OVEN
ABOVE A WARMING DRAWER OPTION
23 /2" Min. _-
inside __
.
Construct
solid bottom
min. 3/8"
plywood
2" Min.
Bottom of warming drawer must be 1"
above toekick
• A 2" min. clearance between oven and
warming drawer cutouts is required.
• Additional clearance may be required if
2 x 4 blocks are used to support the solid
floor of the oven above. Check to be sure
that oven supports above the Warming
Drawer location do not obstruct the
required interior depth and height.
• Refer to warming drawer installation
instructions for electrical requirements and
installation details of that product.
• Warming drawers are approved for
installation below only certain specified
wall oven models. See the label attached to
the top of the oven for approved warming
drawer models.
NOTE: A single wall oven can be installed in
combination with the Advantium oven above
and a warming drawer below as long as the
dimensions and information on this page are
applied to the combination installation.
Loading...