I
I
Refr&erator
English Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
verSiOn franchise......................,... 23
Version en espafiol....... . . . . . . . . . . . . . . 45
Safe~
instructions......., . . . . . . . . . . . . . . . .
3
Operating Instructions, Tips
Automatic
Icemaker
& Dispenser . . . . . . . . 5-7
EnergV-Saving
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Food Storage Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . 8
Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
9, 10
Storage Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Temperature Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
4
Care and Cleaning
Behind the Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning–Inside and Outside . . . . . . . . . . . . . . . . . . 11
Drawer and Cover Removal . . . . . . . . . . . . . . . . . . . . . 12
Light Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . .
.
12
Under Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
11
Water Filter
AccessorV
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
7
GE Appliances
Problem Solver . . . . . . . . . . . . . . . . . . . . .
. 17-19
Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . 17
More questions ?...ln the United States call
GE Answer
Centerm 80~626.2000
In Canada consult your local telephone
tiiectory
for the Cameo
Servjce
Center
Preparation
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
13
Level
ing............
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
13
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
13
Moving & Vacation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
13
Water Supply to Icemaker....... . . . . . . . . . . . . . . . . . 13
Installation
installation... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
14-16
Adapter Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical Requirements . . . . . . . . . . . . . . . . . . . .
.
14
Extension Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
14
Water Line
Installation,...............,...
15, 16
Consumer Services .................20
Appliance Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Model and Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warranty for Canadian Customers ........21
Warranty for U.S. Customers . . . . . . Back Cover
Models: SidebySide2Q2224and27
with Dispenser
HELP US HELP YOU...
Write down the model
and serial numbers.
You’ll sce
them on a
ltibel
on the
wall beside
the
top
drawer or at the bottom, just inside the
fresh food
compartment door.
These numbers are also
on
the Consumer
Product Ownership Registration Card that
came with your refrigerator.
Before sending in this card, please write these
numbers here:
Model Number
Serial Number
Use these numbers in any correspondence or
service calls concerning your refrigerator.
Read this book carefully.
It is
in[ended
to help you
opcra[c
and
maintain your new refrigerator
pI-OpCrly.
Keep it handy for answers [o
yoLIr clucs[itJIls.
If you don’t
undcrst~nd son]c(hing or IIccd
more help,
write
(include
y(mI pllt)nc Il~IIIIbcI):
In the United States:
Consumer
Al”fairs
GE
Appliances
Appliance Park
Louisville, KY 40225
In Canada:
Manager Consumer Relations
2645 Skymark Ave.,
Mississauga, Ontario
Canada L4W 4H2
Save
time and
money.
Ilef’ore
you request service...
(heck (hc
Problem Solver section in this
book.
It
lists minor operating problems that
you can correct yourself.
ENERGY-SAV~G
TWS
● Location of your refrigerator is important. Avoid locating it next to
● Be sure the doors are closed tightly. Before leaving the house or
your range, a heating vent or
wbere
the sun will shine directly on it.
retiring for the night, check to be sure the doors haven’t been
left
●
Close the doors as soon as possible, particularly in hot, humid weather.
open accidentally.
●
Keep foods covered to reduce moisture buildup inside the refrigerator.
IF YOU NEED SERVICE
To obtain service, see the Consumer Services
For Customers in the United States:
page in the back of this book.
FIRST, contact the people who serviced your
We’re proud of our service and want you to
appliance. Explain why you are not pleased.
be pleased. If for some reason you are not
In most cases this will solve
tbe
problem.
happy with the service you receive, here are
3
steps to follow for further help.
NEXT, if you are still not pleased, write
all the details—including your phone
number—to:
Manager, Consumer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
FINALLY, if’ your problem is still not
resolved, write:
Major Appliance Consumer
Action Panel
20
North
Wacker
Drive
Chicago, IL
60606”
For Customers in Canada:
FIRST, contact the people who serviced your
appiiance.
Explain why you are
not
pleased,
In most cases this will solve the problem
NEXT.
if you are still not pleased,
write all
the detai
Is—includin&
your phone number to:
Manager Consumer Relations
2645 Skymark Ave.,
Mississauga, Ontario
Canada L4W 4H2
2
WORTANT SA~TY ~STRUCTIONS
Read W instructions
before
using
ttis
appliance.
A
WARNIN&When
using this appliance,
always exercise basic safety precautions,
including the following:
. Use this
appliance only for its intended purpose
as
described in this Use and Care Guide.
o
Q
This refrigerator must be properly
‘Q-\”:~
?.+ -
installed and located in accordance
with the Instillation Instructions
before it is used.
●
Never unplug your refrigerator by
palling on the power cord.
Always
grip-
plug
firmly
and pull straight out from
the
outlet.
●
Repair or replace immediately all electric
service cords that have become frayed or
otherwise damaged.
Do not use a cord that
shows cracks or abrasion damage along its length
or
at either the plug or connector end.
●
When moving your refrigerator away from the
wall, be
carefd
not to roll over or damage the
power cord.
c
Do not allow children to climb, stand or
hang on the shelves in the refrigerator. They
could damage the refrigerator and seriously
injure themselves.
a
●
If your old refrigerator is still around
the house but not in use, be sure to
remove the doors.
This will reduce the
possibility of danger to children.
c
After your refrigerator is in operation, do
not touch the cold surfaces in the freezer
compartment, particularly when hands are
damp or wet.
Skin may adhere to these extremely
cold
surfaces.
●
If your refrigerator has an automatic
icemaker,
avoid contact with the moving parts of the ejector
mechanism, or with the heating element that
releases the cubes. Do not place fingers or hands
on the automatic
icemaking
mechanism while the
refrigerator is plugged in.
●
Don’t refreeze frozen foods which have thawed
completely.
The United States Department of
Agriculture in Home and Garden Bulletin
No. 69 says:
“..
.You
may safely refreeze frozen foods that
have thawed if they still contain ice crystals or if
they are still cold—below
40°F, (4°C.).
“..
.Thawed
ground meats, poultry or fish that
have any off-odor or off-color should not be
refrozen and should not be eaten. Thawed ice
cream should be discarded. If the odor or color of
any
food is poor or questionable, get rid of it. The
food may be dangerous to eat.
“Even partial thawing and refreezing reduces the
eating quality of foods, particularly fruits,
vegetables and prepared foods. The eating quality
of red meats is affected less than that of many
other foods. Use refrozen foods as soon as
possible to save as much of their eating quality as
you can.”
●
Unplug your refrigerator before
cleaning and making repairs.
NOTE:
We strongly recommend that
any servicing be performed by a
qualified individual.
●
Before replacing a burned-out light bulb, the
refrigerator should be unplugged in order to avoid
contact with a live wire filament. (A burned-out
light bulb may break when being replaced,)
NOTE:
Turning control to OFF position does
not remove power to the light circuit,
●
Do not store or use gasoline or other flammable
vapors and
Iiquids
in the vicinity of this or any
other appliance.
SAW T~SE
~STRUCTIONS
3
OPEMT~G
YOUR
REFMGEWTOR
Set the Temperature Controls
The temperature controls let you regulate the temperature in the fresh
food and freezer compartments.
At
first,
set the Fresh Food control at “5” and the Freezer control at “C”.
Allow 24 hours for the temperature to stabilize, whether you are
setting the controls for the first time or adjusting them later. Then, if
you want colder or warmer temperatures in either compartment, adjust
the controls one step at a time.
NOTE: Moving the Fresh Food control to OFF turns off cooling in
both
compartments-fresb food and freezer—but does not shut off
power to the refrigerator.
How to Test Temperatures
Use the milk test for the fresh food compartment. Place a container
Use the ice cream test for the freezer compartment. Place a
of milk on the
top
shelf in the fresh food compartment. Check it a day
container of ice cream in the center of the freezer compartment. Check
later. If the milk is too warm or too cold, adjust the temperature controls.
it after a day. If it’s too hard or too soft, adjust the temperature controls.
Always
allow
24 hours for the refrigerator to reach the
temperature you set.
Automatic Energy Saver System
No Defrosting
You won’t find an “energy saver” switch on this refrigerator.
It is not necessary to defrost the freezer or fresh food compartments.
Warm liquid from the refrigerator’s condenser is automatically
Your refrigerator is designed and equipped to defrost itself automatically.
circulated around the front edge of the freezer compartment to help
keep moisture from forming on the outside of the refrigerator during
humid weather,
Marry
refrigerators use special electric heaters. This refrigerator needs
none. That’s why there is no “energy saver” switch.. there’s no need
for it.
If you turn your household thermostat below
60°F. (16°C.)
at night...
,. you may want to move the freezer control one
step colder. Cooler temperatures in the house may
cause the compressor to operate less frequently,
! ,’
‘.
thus allowing the freezer compartment to warm
somewhat. To protect your frozen food supply,
leave the freezer
setting
at this colder setting for
D
Moving the freezer control to colder setting should have no effect on
,,. ,.
,.
your fresh food compartment. However, if freezing occurs, move the
#o
fresh food control one step warmer,
$
When you stop turning the thermostat down, turn the refrigerator’s
‘“
controls back to their regular settings.
tbe
entire winter or for-as long as you keep
~our
thermostat tuined down.
4
AUTOWTIC ICEW~R
& DISPENSER
(on some models)
How They Work
The automatic icemaker makes ice continually. The dispenser
dispenses water, ice
cubes or crushed ice through the
freezer
compartment door. Here’s how they work.
Water flows from the
(1)
dual solenoid valve
to the
(2) water tubing and
to the
(3) automatic icemaker
as needed.
Water is frozen in the
(4) cube mold and
ejected into the
(s)
storage bin where
a motor-powered
auger moves
cubes forward.
Cubes fall
throtrgb
the chute in the door when the dispenser
pad is pressed.
When CRUSHED is selected (on some models), a baffle channels
cubes through the crusher and crushed
ice
falls through J chute into
the glass,
When WATER is selected, (on some models) water flows through
tbe
(6) tubing in the door and is dispensed when the dispenser
pad is pressed.
(7) A light switch (on some models) turns the night light in the
dispenser on or off.
The
Iigbt
also comes on
wben
the dispenser pad is pressed.
The light in the dispenser should be replaced with a 7 watt maximum
bulb when it burns out.
Important Facts about Your Ice & Water Dispenser
● If this is your first icemaker you’ll hear occasional sounds that
may be unfamiliar. These are normal
icemaking
sounds and are not
cause for concern.
● Your icemaker will produce 8 cubes per cycle—approximately
120 cubes in a 24-hour period—depending on freezer compartment
temperature. room temperature, number of door openings and other
use conditions.
● Intermittent dispensing of ice is normal. If ice
flow
interruption is
more than brief, ice clump(s) may be the cause and should be
removed following instructions in this section.
● Avoid overfilling glasses with ice and using narrow or extra-tall
glasses. This can jam the chute or cause the door in the chute to
freeze shut. Periodically open the freezer compartment door and look
down into the chute. If ice is blocking the chute, poke it through with
a wooden spoon.
● To help keep bits of ice from being sprayed beyond the glass,
place the glass close to the ice chute—but not so close that it blocks
outcoming
ice.
● Fill glasses with ice before adding soda or other beverage mixes.
● Beverages and foods
sbould
not be quick-chilled in the ice
storage bin. Cans, bottles or food packages in the storage bin may
cause the icemaker or auger to jam.
● Do not add ice from trays or bags to the storage bin.
It
may not
crush or dispense well.
Before Using Your Icemaker and Dispenser
If you use your refrigerator before the water
connection is made, raise the ice access door
and
make sure the icemaker feeler arm is in the
STOP (up) position. When the water supply has
~
been connected to the icemaker, move the feeler
arm to ON (down) position.
4
~!4
,
arm in
min
(up)
n)
position position
At first there will be a
delay
before water is dispensed and ice is
made.
On models with a water dispenser,
if no water is dispensed when the refrigerator is
first installed, there may be air in
the
water line
system. Press the dispenser pad for
at
least two
minutes to remove trapped air from the water
line and to fill the water system.
/
Push the dispenser pad
until the water line is filled.
The ice cube mold will automatically fill with water
A~ER
cooling
to freezer temperatures. The first cubes normally freeze after
several hours.
NOTE: With a newly-installed refrigerator, allow about 24 hours
for the freezer compartment to get cold enough to make ice.
(((ltll;llu(,(l ?1(,.1-[ [?[1,s<,)
5
AUTOWTIC ICEWmR
& DISPENSER
(continued)
Once Your Icemaker and Dispenser are in Operation
Throw away the first few batches of ice cubes (16 or 24 cubes). This
To make sure the bin
fills with ice, level the cubes occasionally.
will
flush away
any
impurities in the water line. Do the same thing
When cubes fall into tbe bin they may pile up close to the icemaker
after vacations or extended periods when ice isn’t used.
and push the feeler arm to the STOP (up) position before the bin gets
On models
witb
a water dispenser, pour the first 6 glassfuls of water in
full.
Keeping the cubes level allows the icemaker to
fill
the bin.
the kitchen sink. The first water through the system picks up a slight
“plastic” taste from the water tubing.
To Dispense Ice and Water
ect
CUBES, CRUSHED ICE
some
models)
or WATER.
Dispenser
pad
● Grip tbe glass or other container
near the rim and press the rim
against the center of the dispenser
pad.
Dispenser
pad
When Dispensing Ice...
When Dispensing Water...
Some”crushed ice maybe dispensed even though you selected
The first glass of water dispensed may be warmer than the
CUBES. This happens occasionally when a few cubes
get
channeled
following ones. This is normal.
to the crusher.
Dispensed water is cool, not iced. For colder water, simply add
Sometimes a mound of snow will form on the door in the ice chute.
crushed ice or cubes before dispensing water.
This condition is normal, and usually occurs when you have dispensed
crushed ice repeatedly, The snow will eventually evaporate.
Sometimes crushed ice will spray beyond the glass. To
avoid
this,
hold the glass up close to the chute.
CAUTION: Never put fingers or other objects into the
dispenser
opeting.
To Stop Dispensing
Release pressure from the
dispenser pad and wait a few
seconds to catch the last bits of ice
or drops of water.
There may be some dripping after
dispensing crushed ice or water. If
there is a lot of dripping, the spill
should be wiped dry right away.
Do not pour water in the spill shelf because it is not self draining—
pour it in the kitchen sink. The shelf
and
its
~rille
should be cleaned
If Ice Clumps Form in the Storage Bin...
The icemaker ejects cubes in groups of 8,
and
it is normal for several
cubes to be joined together. However, if you don’t use the
ice very often, ice clumps may form in the storage bin and can clog
the dispenser.
If this happens:
● Remove the storage bin from the freezer.
● Break up ice clumps with your hands, Throw away any clumps that
you can’t break up.
● Replace the bin before the remaining cubes melt and fuse together.
;egularly according to Care and Cleaning
Press here to remove grille
instructions.
Tbe grille is easily removed
by pressing on the back right corner.
A
6
To Remove Ice Storage Bin
[.ift [he left
corner to tree
the
bin
from
the shelf. Pull the bin straight
out
while
supporting it at front
and back.
To Replace Ice Storage Bin
Slide
the bin back until the tab on the bin locks
into the slot in the shelf.
If the bin does not
go
all the way back, remove
it
and
turn the drive mechanism I/4 turn. Then
push the bin back again until the
tab
on the
bin locks into the slot in the shelf.
If Ice Is Not Used Often...
Move Feeler Arm to STOP (up) Position when...
“Old’. ice
cubes will become cloudy and taste
stale.
Empty
ice
● Home water supply is to be turned off
for
several hours,
storage bin periodically and wash it in lukewarm water, Be sure to
● Ice storage bin is to be removed for a period of time.
allow storage bin to cool before replacing it—otherwise ice cubes will
stick to the metal auger.
●
Goin&
away on vacation, at which time you should also turn off the
valve in the water supply line to your refrigerator.
Water Filter Accessory
Yout ice cubes can
only bc as fresh-tasting as the water that produces them.
/ I
FOOD
STOMGE
SUGGESTIONS
Suggested storage times for meat and poultry*
Eating
quali~
DAYS IN
MONTHS IN
drops after
Eating
quali~
DAYS
IN
MONTHS IN
REFRIGERATOR
FREEZER
drops after
time
shown
REFRIGERATOR
FREEZER
AT 35° to
40°F.
AT O“F.
time shown
(2° to
4“C.)
AT 35° to
40”F.
(-18°c,)
AT O“F.
(2°
to4°c.)
(-18°C.)
Fresh Meats
Fresh Poultry
Roasts (Beef & Lamb) 3 to 5 6 to 12
Chicken & Turkey
(Whole) . . . . . . . . . . . . . . . . 1 to 2..............................12
Roasts (Pork & Veal) 3 to 5 ..,........................4 to 8
Chicken (Pieces) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 2 ,..............................9
Steaks (Beef) . 3 to 5 6 to 12 Turkey (Pieces) 1 to 2 ...............................6
Chops (Lamb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 to 5 ...........................6to 9
Duck & Goose (Whole) . . . . . . . . . . . . . . . . . . . . . 1 to 2...............................6
Choos
(Pork) 3 to 5
..........................,3
to 4
Giblets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
1 to 2
....................,..........3
Ground &
Stew
Meats . 1 to 2
......,........,...........3
to
4+
Variety Meats 1 to 2 ...........................3 to 4
Sausage (Pork) 1 to 2 ...........................1 to 2
Processed Meats
Cooked Poultry
Pieces (Covered with Broth) ..............1 to 2................................6
Pieces (Not Covered) . . . . . . . . . . . . . . . . . . . . . . . . 3 to 4......,,.......................1
Cooked Poultry Dishes 3 to 4 ...........................4 to 6
Frankfutiers...
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
7..................................l/z
Ham (Whole)
....................,......,,,......,,,. 7..,,,,.......,,................1
to 2
Ham (Half) 3 to 5 ...........................1 to 2
Ham (Slices) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
3...............................1 to 2
Luncheon Meats 3 to 5.......... Freezing not recommended.
Sausage (Smoked) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.............. Freezing not recommended.
Sausage (Dry & Semi-Dry) .............14 to 21 ........ Freezing not recommended.
Cooked Meats
Cooked Meats and Meat Dishes . . . . . . . . 3 to 4 ...........................2 to 3
(Other than for meats& poult~)
FREEZER
Most fruits and vegetables ..........8-12 months
Lean fish .......................................6-8 months
Fatty fish, rolls and breads, soups, stew, casseroles .........2-3 months
Cakes, pies, sandwiches, leftovers (cooked),
ice cream (original carton) ......1 month max.
Meats, fish and poultry purchased from the store vary in quality and age;
consequently, safe storage time in your refrigerator will vary.
Gravy & Meat Broth . . . . . . . . . . . . . . . . . . . . . . . . . . 1 to 2 ...........................2 to 3
*U.S. Department of Agriculture
Fresh Food Storage Tips
To store vegetables:
● As a further aid to freshness,
Cbeese:
● Use the vegetable drawers — they have
prepackaged vegetables can be
● Wrap well with wax paper or aluminum
been designed to preserve the natural
stored in their original wrapping.
foil,
or
put in a plastic bag.
moisture and freshness of produce. Unfrozen meats,
fish,
and poultry:
●
Carefully wrap to
expel air and help
● Covering vegetables with a moist towel ● Always remove store wrappings.
helps maintain crispness.
prevent mold.
● Rewrap in foil, plastic wrap or wax paper
● Store prepackaged cheese in its own
and refrigerate immediately.
wrapping if you wish.
Tips on Freezing Foods
There are 3 essential requirements for efficient home freezing.
1. Initial quality. Freeze only top-quality foods, Freezing retains
quality and flavor; it cannot improve quality.
2. Speed. The quicker fruits and vegetables are frozen after picking,
the better the frozen product will be. You’ll save time, too, with less
culling and sorting to do.
3. Proper packaging. Use food wraps designed especially
for freezing.
To freeze meat, fish and poultry, wrap well in freezer-weight foil (or
other heavy-duty wrapping material), forming it carefully to the shape
of the contents. This expels air. Fold and crimp ends of the package to
provide a good, lasting seal. Don’t refreeze meat that has been
completely thawed; meat, whether raw or cooked, can be frozen
successfully only once.
Fine-quality ice cream, with high cream content, will normally
require slightly lower temperatures than more “airy” already-packaged
brands with low cream content.
● It will be necessary to experiment to determine the freezer
compartment location and temperature control setting to keep your
ice cream at the right serving temperature.
● The rear of the freezer compartment is slightly colder than the front.
New
technique.r are
c~n.stantly
being
developed.
Con.rult
the County
Exten.~ion
Service or your
local
Utility Company for the latest
information on,tkeezirrg und .\toring ji)od.~.
8
Fruit &
Vegetable
Drawer
1
Convertible
fl
7: -
Meat Keeper
~
Fruit & Vegetable Drawer (on some models)
Convertible Meat Drawer
(on
some models)
II
This refrigerated drawer keeps unwrapped
foods fresh
by retaining the
The Convertible Meat Drawer has its own
natural moisture content of foods such as: cold air duct to allow a stream of cold air
~
●
Artichokes
●
Cherries
●
Plums
●
Asparagus
from the freezer compartment to flow
●
Corn
●
Radishes
around the drawer.
●
Beets, topped
●
Currants
●
Rhubarb
●
Blueberries
The variable temperature
●
Greens, leafy● Spinach
control regulates the air flow from
●
Carrots
●
Lettuce
●
Tomatoes, ripe
●
Celery
the freezer compartment.
●
Parsley
●
Peas, green
As in any refrigerated storage area, it is recommended that foods with
strong odors be stored wrapped—foods such as:
●
Broccoli
●
Cabbage
●
Parsnips
●
Brussels sprouts
●
Cauliflower● Turnips
●
Green onions
Storage time will depend upon the type of food and its condition when
placed in the drawers.
Excess water that may accumulate in the bottom of the drawer should
be emptied and the drawer wiped dry. The drawer is partially sealed
by gaskets
tittached
to the cover. Always replace the drawer in this
cover and push the drawer all the way
in,
.
Set control lever to MEATS or to
II
II
u
the coldest setting to store fresh meats.
If lever is left in this position for a long
period of time, some frost may form on
the inside of the drawer.
Set control lever to
VEG
or away from the coldest setting to convert
the drawer to normal refrigerator temperature and provide extra
vegetable storage space.
Cold
air duct is turned off.
Variable settings between these extremes can be selected.
Sealed Snack Pack (on some models)
‘The sealed Snack Pack-–and shelf to which it is attached—can be relocated within the Fresh
Food compartment. The sealed drawer retains sufficient humidity for convenient storage of
lunch meats, cheese, hors d’oeuvres, spreads and snacks.
S~I
How to Rearrange Your Shelves
Shelves in the fresh food compartment are adjustable, enabling
you to make efficient shelf arrangements to fit your family’s food
storage needs.
To remove shelves:
Tilt
the shelf up at front,
then lift it up and out of the
tracks on the rear wall of
the refrigerator.
.Ws
To relocate shelves:
Select desired shelf height.
With shelf front raised
slightly, engage the top
hooks in the tracks at the
rear of the cabinet. Then
lower the front of the shelf
until it locks into position.
Wire shelves (on some
models) are adjustable in the
❑
Engage
top
hook
❑
Lower to
lock into place
same manner.
9
S~LWS
(continued)
Bins on Fresh Food Compartment Door
(on
some models)
Adjustable bins
cun
easily be carried
from
refrigerator to
work area.
To remove:
Lift bin straight up until
mounting hooks disengage.
To replace or relocate:
Select desired shelf height.
engage bin’s hook in slots
on the tracks
of the door,
and push in. Bin will lock
in
piace
The divider (on some models) helps prevent tipping, spilling or
sliding of small items stored on the door
shelf.
Place index finger and
middle finger on either side
of the divider near the front and simply
move it back
and
forth to
fit
your needs.
Shelves in Freezer Compartment
Shelves in the freezer are easily removed and replaced
(on some models).
To remove:
1. While pressing tabs on the shelf
supports on right wall, lift the.
shelf out of grooves in the supports.
2. Pull shelf sideways until the
shelf rods come out of holes
on left
wall.
To replace shelves
Insert the rods into the holes. Then,
while pressing the tabs, lower the
shelf into the grooves in the supports.
Be sure the shelf wire is fully inserted
into grooves.
If shelf supports at desired level on
right wall do not have tabs, merely
lower shelf into place on supports.
9
Deep Door Shelves in the Freezer Compartment (on some models)
Detachable shelf extenders deepen and enclose fixed
door shelves, providing more storage room and greater
storage flexibility.
To remove: Lift the shelf extender straight up until the
mounting hooks come out
of the slots in the door.
To replace: Line up the hooks with the slots in the door
and push in and down.
Quick Shelf
TM
Swing Down Shelf (on some models)
This swing-down shelf
provides extra shelf space when
needed.
When you want to use it, pull
the shelf forward as far
as
it goes,
then lower
it.
Be careful not to
force it down before it is pulled
e
;
b
—-
—
:11,-,
~-.%~v~,
~
out
all
the way.
n+
To raise it back into position, pull the shelf forward, push it up and
slide it back
fully
until it stops.
10
Cleaning—Outside
The
water and ice dispenser spill shelf should be wiped dry
immediately
to
prevent spotting, Water left on the shelf may leave
deposits that you can remove
by
soaking with undiluted vinegar. You
can also use a paste of non-precipitating water softener (such as
Calgon
brand) and water, or I teaspoon (5 ml) of citric acid powder
per pint (500 ml) of hot tap water. Soak until the deposit disappears or
becomes loose enough to rinse away. Usually
30
minutes
sofiking
time
is adequate. Avoid using wax on the spill shelf and trim.
The door handles and trim can be cleaned with a cloth dampened
with a solution of mild liquid dishwashing detergent
and
water.
Dry
with a soft cloth. Don’t use wax on the door handles
~nd
trim.
Keep the finish clean. Wipe with a clean cloth lightly dampened
witt
kitchen appliance wax or mild liquid dishwashing detergent. Dry and
polish with a clean, soft cloth. Do not wipe the refrigerator with a
soiled dishwashing cloth or wet towel. These may leave a residue that
can
erode the paint. Do not use scouring pads, powdered cleaners,
bleach or cleaners containing bleach because these products can
scratch and weaken the paint finish.
Protect the paint finish. The finish on the outside of the refrigerator
is a high quality, baked-on paint finish. With proper care, it will stay
new-looking and rust-free for years. Apply a coat of
kitchen/applianct
wax when the refrigerator is new and then at least twice a year.
Appliance Polish Wax & Cleaner (Cat. No.
WR97X0216)
is available
from Service and Parts Centers.
Cleaning—Inside
Inside the fresh food and freezer compartments should be cleaned
at least once a year. Unplug the refrigerator before cleaning. If this is
not practical, wring excess moisture out of sponge or cloth when
cleaning around switches, lights or controls.
Use warm water and baking soda solution—about a tablespoon
(I5 ml) of baking soda to a quart ( 1 L) of water. This both cleans
and
neutralizes odors. Rinse thoroughly with water and wipe dry,
Other parts of the refrigerator—including door gaskets, meat and
vegetable drawers, ice storage bin and ail plastic part—can be
cleand
the same way. After cleaning door gaskets, apply a thin layer
of petroleum jelly to the door gaskets at the hinge side. This helps
keep the gaskets from sticking and bending out of shape. Do not use
cleansing powders or other abrasive cleaners.
Avoid cleaning cold glass shelves with hot water
bectiuse
the extreme
temperature difference may cause them to break.
To help prevent odors, leave an open box of baking soda in the
rear of the refrigerator, on the top shelf. Change the box every
3
months. An open box of baking soda in the freezer will absorb stale
freezer odors.
Do not wash any plastic parts from your refrigerator in
your automatic dishwasher.
Drain opening in freezer compartment.
During yearly cleaning, remove bottom freezer
basket and flush a solution of baking soda —
1 teaspoon (5 ml) and 2 cups (500 ml) of hot
(not boiling) water— through the drain line with
the help of a meat baster. This will help eliminate
odor and reduce the likelihood of a clogged drain
line. If drain becomes clogged, use a meat baster
and
baking-soda-and-water solution to force the
clog through the drain line.
Behind Refrigerator
Care should be taken in moving your refrigerator away
from
the wall.
All types of floor coverings can be damaged, particularly cushioned
coverings and those with embossed surfaces. Pull the refrigerator
straight out and return it to position by pushing it straight in. Moving
your refrigerator in a side direction may result in
damage
to your
floo[
covering or refrigerator.
When pushing the refrigerator back, make sure you don’t roll over the
power cord or
icemaker supply line (on some models).
Under Refrigerator
For most efficient operation,
you need to keep the area under the
refrigerator clean. Remove the base
grille and either sweep away or
vacuum up dust that is readily
~ccessible.
For best results, use a
brush specially designed for this
purpose. It is available at most
appliance parts stores. This easy
ci~aning
operation should be done
/
at least~n;e a year.
Clean the condenser coils
at least once a year.
((on[inued nexl
page)
11
CAW Am
CLEAN~G
(continued)
Drawer Removal
Drawers will stop
before coming
all the way out of the refrigerator to
help prevent contents from spilling
onto
the
floor,
Drawers can easily
be rcmoved
by tilting up slightly and pulling past the “stop” location.
To remove drawers when the refrigerator door cannot be opened
all the way:
1. Remove food
from
the drawer and its cover. If your refrigerator has
adjustable shelves, remove
food
from the bottom shelf and
temporarily relocate it
higber
up in cabinet.
2. Remove the flexible gasket at the
rear of tbe top drawer. Lift each
:1
end straight up until the slots on
the gasket are free of the drawer
support
tabs.
*
“
‘,. ,,,;,, ,/,
,
r“
‘----=--
*
/l/Ajj/l’l!
--——
————_-.. .–
3. Pull the drawer partway out. Reach
in, push the rear of the glass up; at
the same time,
pusb
it back until it
clears front-corner retainers.
4. Tilt
and
remove the cover.
5. Pull the drawer forward, lift the
front
to
clear stops, and remove tbe
drawer.
If the refrigerator door
doesn’t open completely, pull the
drawer out until it hits the
door.
Then lift the drawer up until it is
higher
than
the drawer supports, tilt
it and take it out.
6.
If tape holds the Convertible Meat
Drawer (on some models) cover to
the
drawer supports, remove the
ta~e.
Pull drawer
partway
out. Reach
‘m
.JQ,YI
jli,,
in:
push the rear if tbe
g~ass
up and,
at
the same time, back, until it clears
front-corner retainers,
7. Tilt
tirrd
remove the cover.
Avoid cleaning the cold glass cover
with hot water because the extreme
temperature difference may cause it
to break.
8.
Tilt and remove the drawer.
After cleaning, replace in reverse
order. When replacing the drawer
make sure
you
slide it through both
drawer
guides
on the
left
side.
When drawers and covers are back in
place,
reinstall gasket at the rear of the
top drawer. Fit the end of the plastic
drawer support into the slot on the
Easket,
with the rubber gasket tlap
facing
you. Make sure the gasket
snaps into place.
e
‘~:
~~
--” ‘~:,/~~ z>,,,
,’/,’//// ,1
-.—-.=
=—=.
Light Bulb Replacement
Fresh Food Compartment-Upper Light
1. Unplug refrigerator.
—
2.
To align the control knob
Grooved
properly, note position of
~:~~~lde
numbered control for proper
reassembly, turn control to
OFF
and
pull off knob.
3.
PLdl
bottom of
li&ht
panel
down about
1/4
inch (6 mm)
‘m
Pin
retainer,
‘&: ,%
*Q %:&
-.
~~
.1
-
,,,
just enough to disengage lip at
rear from grooves in retainers
\!
7,
on rear wall.
4. Lift panel to disengage top from pins on side walls and
remove panel.
After replacing with same size bulb, reinstall panel (hang top on pins;
pull bottom down, push it back and release it to let lip
engage
grooves
in retainers). Replace temperature control knob in OFF position, turn
it to previous setting and plug refrigerator back
in.
Fresh Food Compartment-Lower Light (on some models)
This light is located behind a shield at the rear of tbe fresh food
compartment
1.
Unplug the refrigerator.
2. Grasp the top edge of the shield and lift it up and forward to free its
top
edge.
3. After replacing with the same size bulb, hook the top of the
shield
back in place.
Freezer Compartment
1.
Unplug the refrigerator.
2. Remove the shelf just below light shield. (The shelf
will be easier to remove if it is emptied first. )
3. Pull the light shield
toward
you to reach the bulb.
After replacing with same size bulb, reinstall shelf and plug the
refrigerator back in.
12
Preparing for Vacation
Preparing to Move
For shorter vacations, remove perishable foods and leave controls
Disconnect power cord from wall outlet, remove
all
food, and clean
at regular settings. However, if room temperature is expected to
drop below
60°F.
(
16°C.),
follow same instructions in Temperature
and dry the interior,
Control section.
Secure
all
loose items such as grille, shelves and storage pans by
taping them securely in
place to prevent damage.
For
long
vacations or absences, remove food and shut off power to
Be sure refrigerator stays in
upright
position during actual moving
an(
refrigerator. Move the Fresh Food control to OFF position and clean
interior with baking soda solution of
I
tablespoon (15 ml) of soda to
in van. Refrigerator must be secured in van to prevent movement.
1 quart (1 L) of water. Wipe dry. To prevent odors,
leave
open box of
Protect outside of refrigerator with blanket.
soda in refrigerator. Leave doors open.
Move the icemaker (on some models) feeler arm to STOP (up)
position and be sure to shut off water supply to the refrigerator.
Refrigerator Location
Clearances
Do not install refrigerator where temperature
will
be below
Allow the following clearances for ease
of installation, proper air
60°F. (16°C.)
because it will not run often enough to maintain
circulation, plumbing and electrical connections.
proper temperatures.
Sides
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
5/8” (15
mm)
Do install it on a floor strong enough to support a fully loaded
Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
1“ (25 mm)
refrigerator.
(~built-in,
allow 7& ’’(22 mm) for hinge covers.)
Also see Energy-Saving Tips regarding location.
Back l“ (25 mm)
If the refrigerator is against a wall on either side,
allow
the
following door clearances:
for 20’, 22’ and 24’ models
....,...........................3/4”
(19 mm)
for 27’ models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
........1 ‘/1” (38 mm)
Rollers
Adjustable rollers behind the base
grille
enable you to move the
refrigerator away from the wall for
cleaning. These rollers should be set
so the refrigerator rests firmly on the
floor. To assure that the doors
will
close automatically from a half-way- s
open position, there is a built-in tilt
from the front to the back of the
cabinet.
Side-bv-side refrigerators
also
Leveling
F
To adjust rollers, remove the base
grille by grasping it at the bottom and
&
pulling it out.
.,.
,,,’
1
firn
the roller adjusting screws
clockwise to raise the refrigerator,
*
h
~~Ü‹(•v•tÙp•èØp•ÀÑp•
@
counterclockwise to lower it. Use an
‘~ ‘%@i”r.:,
adjustable wrench (3/8” (9 mm) hex
. .
.
~90N6
head bolt) or pliers.
When leveling, you can improve door closure by raising the front
have specially
~esigned d~or
hinges that
lift
both doors slightly when
approximately 5/8” (15 mm)
trom
the
floor.
opened, allowing the force of gravity to help close them securely.
To replace base grille,
align
prongs on back of grille with clamps in
cabinet and push forward
until grille
snaps into place.
Water Supply to Icemaker (on some models)
If your refrigerator has an icemaker, or if you plan to add an icemaker later, the icemaker will have
to be connected to a
cold
water line. A water supply kit containing copper tubing, shut-off valve,
fittings and instructions is available at extra cost from your dealer. There should be sufficient tubing
for the icemaker from the cold water supply to allow you to move the refrigerator out from the wall
several feet (approximately 8 feet (244 cm) of
l/4° (6 mm) copper tubing in three 10-inch (25 cm)
diameter coils),
13
~STALLATION ~~UI~MENTS
IMPORTANT... PLEASE
RE
CA~FULLY
How to Connect Electricity
For personal safety, this
appliance must be
properly grounded.
The power cord of
tbis
appliance is equipped with a
3-prong (grounding) plug
which mates with a standard
3-prong (grounding) wall
outlet to minimize the
possibility
of electric shock
hazard
from
this appliance.
Pref
Have the wall outlet and circuit checked by a qualified electrician!
to
make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your
personal responsibility and obligation to have it replaced with
a
properly grounded 3-prong
wall
outlet.
I I
DO
NOT, UNDER
ANY CIRCUMSTANCES, CUT OR REMOVE
THE THIRD (GROUND) PRONG FROM THE POWER CORD.
I
I
Use of Adapter Plug
Because of potential
hazards under certain
conditions, we strongly
recommend
agtiinst
use
of an adapter plug.
However, if you still elect
to use
an
adapter, where
local codes permit, a
TEMPORARY
CONNECTION may be
made to a properly
grounded 2-prong
wall outlet by use of
a UL listed adapter
available at most local
hardwfire
stores.
TemporaW Method
(Adapter plugs not
permitted in Canada.)
Align large prongs/slots.
~n
@
.
/---
“
A
w“-”
/
w“’
u
Insure proper grounding and firm
connection exists before use.
The larger slot in the adapter must be aligned with
the
larger slot in
the wall outlet to provide proper polarity in the connection of the
power cord.
Use of an adapter plug will increase the clearance needed for the back
of the refrigerator.
CAUTION: Attaching the adapter
ground terminal to a wall outlet
cover screw does not ground the appliance unless the cover screw is
metal,
and not insulated, and the wall outlet is grounded through the
house wiring. You should have the circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
When disconnecting the power cord from the adapter,
always
hold
the adapter in
place
with one hand while pulling the power cord plug
with the other hand.
If
this is not done, the adapter ground
terminul
is
very likely to break with repeated use.
Should the adapter ground terminal break, DO NOT USE the
appliance until a proper ground has again been established.
Electrical Requirements
Use of Extension Cords
The refrigerator should always be plugged into its own individual
Because of potential safety hazards under certain conditions, we
electrical
outlet
which has a voltage rating that matches the rating plate.
strongly recommend against the use of an extension cord. However. if
This provides the best performance and also prevents overloading house
you still elect to use an extension cord, it is absolutely necessary that it
wiring circuits which
could
cause a fire
hazard froln
overheated wires.
be a
UL-listed
3-wire grounding type appliance extension cord having
a grounding type plug and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and
120
volts.
14
UUTION:
● If you use your refrigerator before connecting
the water line, make sure the icemaker feeler arm
is kept in the STOP (up) position.
. Do not install the icemaker tubing in areas
where temperatures fall below freezing.
●
When using any electrical device (such as a
power drill) during installation, be sure the device
is insulated or wired in a manner to prevent the
hazard of electric shock.
●
Al
installations must be in accordance with
local plumbing code requirements.
WHAT YOU WILL NEED
● A cold water supply is required for automatic
icemaker operation. The water pressure must be
between
20 and 120
p.s.i.
●
Power
dri~,
unless you have a
seti-piercing
valve.
● Copper tubing, 1/4” (6 mm) outer diameter to
connect the refrigerator to the water supply. Be
sure both ends of the tubing are cut square.
To determine how much copper tubing you need:
measure the distance from the water valve on the
back of the refrigerator to the water supply pipe.
Then add 8 feet (244 cm). Be sure there is
sufficient extra tubing (about 8 feet [244 cm]
coiled into 3 turns of about 10 inches [25 cm]
diameter) to allow the refrigerator to move out
from the wall after installation. Do not use plastic
tubing or plastic fittings because the water supply
line is under pressure at all times.
Mso,
certain
types of plastic tubing may become brittle with
age and crack, resulting in water leakage.
c
Shutoff valve to connect to the cold water line.
The shut-off valve should have a water inlet with a
minimum inside diameter of 5/32” (4 mm) at the
point of connection to the COLD WATER LINE.
Saddle-type shut-off valves are included in many
water supply kits. Before purchasing, make sure a
saddle-~pe valve complies with your local
plumbing codes.
. Two 1/4” (6 mm) outer diameter compression
nuts and 2 ferrules (sleeves) – to connect the
copper tubing to the shutoff valve and the
refrigerator water valve.
●
If your existing water line has a flared fitting at
the end, you will need an adapter (available at
plumbing supply stores) to connect the water line
to the refrigerator OR - you can cut off the flared
fitting with a tube cutter and then use a
compression fitting.
WARRANTY INFORMATION
This water
tie
initiation is not warranted by
tie
refrigerator or icemaker manufacturer.
FOMOW
these instructions
ae~
to minimize
the risk of expensive water damage.
❑
SHUT OFF THE
WIN
WATER SUPPLY.
Turn on the nearest faucet long enough to clear
the line of water.
❑
INSTALL THE SHUTOFF VALVE ON THE
NEAREST FREQUENTLY USED DRINKING
WATER LINE.
Typical ways to
connect
to water supply
Through floor
Under sink
Through wall to
In crawl
to basement
to cold utility room cold
space
under
cold water pipe
water pipe water pipe
house
a.
Choose a location for the valve that is easily
accessible. It is best to connect into the side of
a vertical water pipe. When it is necessary to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
b. Drill a 1/4” (6 mm) hole in the water pipe,
using a sharp bit. Remove any burrs resulting
from drilling the hole in the pipe. (Do not drill a
hole if the valve is a
seM-piercing
type.)
c. Fasten the
shutoff valve to
the cold water pipe
with the pipe clamp.
d. Tighten the
clam~
screws until the
t
seali~g
washer begins to
swell. Do not overtighten
or you may crush the
4
Veflical
cold water
pipe
copper tubing.
(((jlftitri((,(l
11(,.\r 17cI,Y1,)
15
❑
ROUTE THE COPPER TUBING BETWEEN THE
COLD WATER LINE AND THE
REFRIGEWTOR.
Route the tubing through a hole drilled in the
floor or wall
@ehind
the refrigerator or adjacent
base cabinet) as close to the wall as possible. Be
sure there is sufficient extra tubing (about 8 feet
[244 cm] coiled into 3 turns of about 10” [25 cm]
diameter) to allow the refrigerator to move out
from the wall after installation.
❑
CONNECT THE COPPER TUBING TO THE
SHUTOFF VALVE.
Compression nut
Saddle type
Place the compression
shutoff valve
nut and ferrule (sleeve)
onto the end of the
JALI
WI
I
Tighten the compression
~u~letv,l~ I
\
Ferrule
nut securely.
(sleeve)
—
I
~
TURN ON THE
WATERAHD
FLUSH OUT
THE TUBING.
a.
Turn the main water supply on and flush out
the tubing until the water is clear.
b. Shut the water off at the water valve after
about one quart of water has been flushed
through the tubing.
❑
CONNECT THE COPPER TUBING TO
THE REFRIGERATOR.
Before
mating
the connection to the
refrigerator, be sure the refrigerator power
cord is not plugged into the
wdl
outiet.
We recommend installing a water filter
(available at Service and Parts Centers) if your
water supply has sand or particles that could clog
the screen of the refrigerator’s water valve. Install
it in the water line near the refrigerator.
a.
Remove the plastic flexible cap from the
water valve.
b. Place the
compression nut
and ferrule
(sleeve) onto the
end of the tubing
as shown.
c. Insert the end
of the copper
tubing into the
water valve
connection as far
as possible. While
1/4” Copper
Tubing
tubing (6 mm)
clamp
holding
Refrigerator connection
the tubing, tighten the
fi~ing.
d. Fasten the copper tubing into the clamp
provided to hold it in a vertical position. You may
need to pry open the clamp.
❑
TURN THE WATER ON AT THE
SHUTOFF VALVE.
Tighten any connections that leak.
❑
PLUG THE REFRIGERATOR POWER CORD
INTO A GROUNDED ELECTRICAL OUTLET.
❑
SET THE ICEMAKER FEELER ARM TO THE OH
(DOWN) POSITION.
The
icemaker will not begin to operate until it
reaches its operating temperature of
15°F (-9°C.)
or below. It will then begin operation automatically
tithe
icemaker is in the ON (down) position.
NO~:
The icemaker may double-cycle when it
first starts, causing some water spillage from the
icemaker into the ice bucket. This is normal and
should not happen again. The first few batches of
cubes should be thrown away, so that remaining
impurities in the water line will be flushed out.
❑
MOVE THE REFRIGERATOR BACK TO
THE WALL.
~range
the coil of copper tubing so that it does
not vibrate against the back of the refrigerator or
against the wall.
16
QUESTIONS?
USE THIS PROBLEM SOLVER
PROBLEM
REFWGERATOR
DOES NOT OPERATE
MOTOR OPERATES
FOR LONG PERIODS
MOTOR STARTS
&
‘TOPS FREQUENTLY
VIBRATION OR
RATTLING
POSSIBLE CAUSE
●
May be in
defrost cycle when motor does not operate for about 30 minutes.
●
Temperature control in OFF position.
c
If interior light is not on, refrigerator may not be plugged in at wall outlet.
●
If plug is secure and the refrigerator still ftils to operate, plug a
lamp
or a
small
appliance into the same outlet to determine if there is a tripped circuit breaker or
burned out fuse.
●
Modern refrigerators with more storage space and a larger freezer
compartment require more operating time.
●
Normal when refrigerator is first delivered to your home—usually requires 24
hours to completely cool down.
●
Large amounts of food placed in refrigerator to be cooled or frozen.
●
Hot weather—frequent door openings.
●
Door left open.
●
Temperature controls are set too cold. Refer to instructions for use
of Temperature Controls.
●
Grille and condenser need cleaning. Refer to Care and Cleaning page.
●
Check Energy-Saving Tips.
●
Temperature control starts and stops motor to maintain even temperatures.
●
If refrigerator vibrates, more than likely it is not resting solidly on the floor and
front roller screws or front leveling legs need adjusting, or floor is weak or uneven.
Refer to Rollers section on Installation Requirements page.
●
If dishes vibrate on shelves, try moving them. Slight vibration is normal.
NOWL OPEMTING
SOUNDS
I
~ese sowds
are normal and do not
hdate
a need for sertice.
The new high efficiency compressor runs faster and will have a higher
pitch hum or pulsating sound while operating.
Defrost timer and refrigerator control clicks on and off.
The fan circulating air inside the freezer which keeps the
temperatures throughout.
Water dropping on the defrost heater causing a
sizzling, hissing or popping sound during the defrost cycle.
The flow of refrigerant through the freezer cooling
coil sounds like boiling water or a gurgling noise.
Cracking or popping of cooling coils caused by expansion
and contraction during defrost and refrigeration
!,.
8;<
Water dripping as it melts from the evaporator
and flows to the drain pan during the defrost
cyc
Icem*er
(on some models):
The
icemaker
water valve will buzz when the ice
with water.
fithe feeler arm is in the ON (down) position it will buzz even if it has
not yet been hooked
up to water. Keeping the feeler arm in the ON (down) position
before it is hooked u~ to water can
damage
the
icemaker.
To prevent this, raise the
feeler arm to the ~P (up) position.
Th;s
will stop the buzzing.
(((>~7tinu(,d ~7f,.rf I)CIX<,,
me
sound of cubes
dropphg
into the bin and water running in pipes as
icemaker retis.
17
PROBLEM
SOLWR
(continued)
PROBLEM
HOT AIR FROM
BOTTOM OF
REFRIGERATOR
DOOR NOT CLOSING
PROPERLY
FRESH FOOD OR
FREEZER COMPARTMENT
TEMPEWTURE
TOO WARM
FOODS DRY OUT
FROST OR ICE
CRYSTALS ON
FROZEN FOOD
SLOW ICE CUBE
FREEZING
ICE CUBES HAVE
ODOWTASTE
AUTOMATIC
ICEMAKER
DOES NOT WORK
CUBE DISPENSER
DOES NOT WORK
POSSIBLE CAUSE
s
Normal air flow cooling motor.
In the refrigeration process, it is normal that heat
be expelled in the area under the refrigerator. Some floor coverings will discolor
at these normal and safe operating temperatures. Your floor covering supplier
should be consulted if you object to this discoloration.
. Door gasket on hinge side sticking or folding over. To correct, put a small
amount of petroleum jelly on face of gasket.
●
Temperature control not set cold enough. Refer to Temperature Control section.
●
Warm weather—frequent door openings.
●
Door left open for long time.
●
Package may be holding door open.
●
Foods not covered, wrapped or sealed properly.
. Door may have been left ajar or package holding door open.
●
Too frequent or too long door openings.
●
Frost within package is normal.
●
Door may have been left open.
●
Turn temperature of freezer compartment colder.
●
Old cubes need to be discarded.
●
Ice storage bin needs to be emptied and washed.
●
Unsealed packages in refrigerator andor freezer compartments may be
transmitting odor/taste to ice cubes.
●
Interior of refrigerator needs cleaning
—refer to Care and Cleaning section.
●
Poor-tasting incoming water. Install a water filter—see Water Filter
Accessory section.
●
ON-STOP control in STOP (up) position.
●
Water supply turned off or not connected.
●
Freezer compartment too warm.
●
Cubes too small-water shutoff valve connecting refrigerator to home
water line may be clogged.
●
Sometimes cubes fuse to the side of the ice mold and hold the feeler arm in the
STOP (up) position. Remove this ice to restart the icemaker.
●
When reaching for cubes by hand, you may have pushed the feeler arm into the
STOP (up) position by mistake.
●
Piled up cubes in storage bin may cause icemaker to shut off too soon. With
icemaker feeler arm in STOP (up) position, level cubes in bin.
●
No ice cubes. Remove storage container. If cubes are frozen to wire arm,
remove cubes.
●
No ice cubes. Icemaker turned off or water supply turned off.
“
Irregular ice clumps in storage container.
Bre&
up as many as you can with
fingertip pressure and discard the remaining clumps.
18
PROBLEM
WATER HAS POOR
TASTE/ODOR
WATER IN FIRST
GLASS IS WARM
WATER DISPENSER
DOES NOT WORK
DIVIDER BETWEEN
FRESH FOOD AND
FREEZER COMPARTMENTS FEELS WARM
MOISTURE FORMS
ON OUTSIDE OF
REFRIGERATOR
MOISTURE
COLLECTS INSIDE
WATER ON KITCHEN
FLOOR OR ON
BOTTOM OF FREEZER
REFRIGERATOR
HAS ODOR
INTERIOR LIGHT
DOES NOT WORK
POSSIBLE CAUSE
●
If the water dispenser
has
not been used for a long time, dispense water
in regular manner until
all
water in the system is replenished with fresh water,
●
Poor-tasting incoming water. Install a water filter—see Water Filter section.
●
Allow about 24 hours for water to cool to proper temperature after
refrigerator is first installed.
●
If water dispenser has not been used for a long time, water in first
glass will not be as cool as in succeeding glasses.
●
If the water system has been drained, allow several hours for replenished
supply to
chill.
c
Water supply line turned off or not connected.
●
Supply line may be clogged with sediment.
●
If no water is dispensed when the refrigerator is first installed, there may be air in
the water system. Press the dispenser pad for at least two minutes to remove trapped
air from the water line and to fill the water system.
●
Normal warmth is created by automatic energy saver system circulating warm
liquid around front edge of freezer compartment to help prevent condensation
on outside of refrigerator in hot, humid weather.
●
Not unusual during periods of high humidity.
●
Too frequent or too long door openings.
●
In humid weather, air carries moisture into refrigerator when doors are opened.
●
The drain in the bottom of the refrigerator may be clogged. Remove any ice on
the freezer bottom and clean the drain. Refer to Care and Cleaning section.
“
When using the dispenser use a glass no taller than six inches (15 cm) tall. A taller
glass may be jamming cubes in the funnel chute. They can fuse inside the chute
and drop out later, leaving water or ice on the floor.
●
Foods with strong odors should be tightly covered.
●
Check for spoiled food.
●
Interior needs cleaning. Refer to Care and Cleaning section.
“
Defrost water
system
needs cleaning.
●
Keep open box of baking soda in refrigerator; replace every 3 months.
●
No power at outlet.
●
Light bulb needs replacing. See Care and Cleaning section.
If you need more help...
In the United States call, toll free:
GE Answer Center” 800.626.2000 consumer information service
In Canada: Manager Consumer Relations
2645
Skymark Ave.,
Mississauga,
Ontario Canada
L4W 4H2
19
We’ll Be There
Witi
the purchase
ofyc)ur
new GE appliance, receive the assurance that
ifyou
ever need information”
or assistance from
CJE,
we’ll be there. All you have to do is
call+)r
write!
In-Home Repair Service
In the
UndedStates:80MEXARES (80M32-2737)
A(;klr(msunlcr
scrvicc’f]ro[i:ssit)rl;il will[)r-()~iclc.cxf]c,r[ rc’p:iit-s er-vice,sc :heclufeci
at :~timc{tl;i[’sconvcnicrlt fory(m, Many(;F(;or]slrrllt!r
Scmicc:c or~lp~~ny-()[~er-: ite(l loc:ttiorlsoflktyou
scr~icetocf;lyot-tomorrow,
orat
yourc:(mvenienc:e (7:() ()a.m. t[)7:()()p.m.
weckci~~ys, !):()()
a.m. [02:()()p.m.S:~t~lrci~iys) .()~llfi~ct()ry-tr:linc!ci
re(llrli(i~{nskrlow”
y(nrrapf]liance insicle~inclotlt-so”
lT~ostl-c:p:~irs(:all
hell:{rl(lleclirlj~ls[
(mc
visil.
In Canada
consultyourlocal
telephone tiiectoryforthe Cameo Service or
AuthorkedService
Center
nearestyou.
GEAnswerCente~
In the
UnitedStates:80~6262000
Whatt:vcryour
(fllc’s[iotl:iho~i[” :irly(; lir Tl:\jor:t[]f>li: irlcc,
(;l;.
,\rlswcr(;errrel-@) illfi)rrrl:~liorlsc,rvice is:ll,:iil:lt)lctoflclf]. YOL]l-(2111-:{rlclyoLlr”
qtresti(m-willbc :~nswel’c’clf>r’onlptfy ;ir~ci(’()~lrtt>()trsly. AncIyoL](’:irl[’:ll12irly
ti]ne. (; E:
Ar]s\vcr(; cntcl(” >
scrvic:c
is open
2’4110LLl’s21[12L}J,
7cia>s
~]
week.
In Canada contact
Managec
Consumer Relations, Cameo, Inc., 2645
S@markAvenue, Mississauga,
Ontario, Canada
L4W4H2
kr
Customers With Special Needs...
In the United
States:80~62E2000
UpmT1-ecfuest,(;E
willf>r’ovidcflr-:~illc” c:orltr’olsfi )t:iv ’:lriery”
of’(;ll:~ppii~inces, arld:iht-ochurc
to;~ssist
irlpl;lnnirlg :tt]:tt’rict’-f i’ct: ki~(herlfi)t
[)ersorls~vitl~limitecl mohility.’root]r>~irl rllcscitcr]~s,
ficcof’(ll;~tge,
(:;111800.(;26.2000.
(;otlstrmers
with ir]lp:~irc:cIt]e;itirlg
ot-specrh
whoh~[ve
:icccssto:iTl)l)ol-” :i(:orlventiorl;~ lteletypt:wrr-i[er”” 111:~yc:t11800J1’1
)1)-(
;l{A(;”
(800-8f3f3-4f322)” loreqllcslin fi)rr~l;ltiorl( ~r-” st>r-virc.
In Canada contact
ManageK
Consumer Relations, Cameo, Inc., 2645
SkymarkAvenue, Mississauga,
Ontario, Canada
L4W4H2
Service contracts
In the
UndedStates:80M2&2224
80M61-36361n
Canada
Pa& andAccessories
In
tie
United
States:80@626-2002
Indtidtrafs
qutified toservice~eirown
apphaces(:~ntl;ltc’
rlcc,cl<:clp:irtsor ;~c:(c’ssoriesscrlt clirt:(:tlyt ottlc’irhor
T]c:.”
Ttle(;EI[)~trtssystcrr~
pro~icl(:s:~((ess
toovcr47,(
)()()
p~11ts...:~r]c1° :ill(;~(;t:rl~]illt Rt’rlcw~il
f’:irts:~re fillly warranted. VISA,
M:tster”(;:lrcii
~ncll)isco\er c:arrisiuc
arc’cpted.
User maintenance instructions contained in this boofdet cover procedures intended to be performed by any user. Other servicing
generaffy
shodd
be referred to
quafified
service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
In Canada
consultyourlocal
telephone
tiiectoryhr
the Cameo Service
orAuthorhedService
Center
nearest you
20
CONSUMER WARRANTY
(for customers in Canada)
FIRST
YEAR
CAMCO
warrants the replacement or repair of all parts of this Refrigerator which prove to be
defective in material or workmanship, for one year from the date of purchase. Such
pafls will be
repaired or replaced at the option of Cameo without charge, subject to the terms and conditions
set out below.
The DEALER warrants to provide the service labor for the repair or replacement of all pafls of
this Refrigerator which prove to be defective in material or workmanship for one year from the
date of purchase.
NEXT FOUR YEARS
CAMCO warrants the hermetically sealed refrigerator system (namely: Evaporator, Condenser,
Motor Compressor, interconnecting Tubing, Drier and Refrigerant Charge) against defects in
material or workmanship for an additional four years. These parts will be repaired or replaced
at the option of Cameo without charge, subject to the terms and conditions set out below.
The DEALER warrants for the next four years to provide the service labor necessary to repair
or replace the hermetically sealed refrigeration system, subject to the terms and conditions set
out below.
TERMS AND CONDITIONS
1.
This warranty applies only to single family domestic use in Canada when the Refrigerator has
been properly installed according to the instructions supplied by Cameo and is connected to
an adequate and proper utility service. Damage due to abuse, accident, commercial use, and
alteration or the removal or defacing of the serial plate, cancels all obligations of this warranty.
Service during this warranty must be
petiormed by an Authorized Cameo Service Agent.
2. Neither Cameo nor the Dealer is liable for any claims or damages resulting from any failure of
the Refrigerator or from service delays beyond their reasonable control.
3. To obtain warranty service, purchaser must present the original bill of sale. Components
repaired or replaced are warranted through the remainder of the original warranty period only.
4. This warranty does not cover expense involved in making this appliance readily accessible
for
sewicing.
5. This warranty gives you specific legal rights. Additional warranty rights may be provided by
law in some areas.
Cameo
Sewice is available coast-to-coast. See preceding page for sewice information.
If
futiher help is needed concerning this Warranty, contact:
Manager, Consumer Relations
Cameo Inc., Consumer Service
2645
Skymark Avenue,
Mississauga,
Ontario
L4W
4H2
I Pati No. 162 D7733PO01
I
Pub.
No.
49-6775
I
Side by Side 20, 22, 24 and 27 Models
21
NOTAS
67
YOUR GENERAL ELECTRIC REFRIGERATOR
Staple
sales slip or
cancelled
check
WARRANTY
here. Proof of original
purchase
date
is needed to obtain service
(for customers in the United States)
under warranty.
I
I
WHAT IS COVERED
FULL ONE-YEAR WARRANTY
For one year from date of original
purchase, we will provide, free of
charge, parts and
sewice labor in
your home to repair or replace
any
Pati
of
the
refrigerator that fails
because of a manufacturing defect.
FULL FIVE-YEAR WARRANTY
For five years from date of original
purchase, we will provide, free of
charge, parts and service labor in
your home to repair or replace any
part of the sealed refrigerating
system (the compressor, condenser,
evaporator and all connecting
tubing) that fails because of a
manufacturing defect.
LIMITED LIFETIME WARRANTY
For the life of the refrigerator, we
will replace, free of charge,
any
sethrough
pan or drawer made
from
Lexa#
po/ycarbonate
resjn
and furnished with the refrigerator if
the pan or drawer breaks during
normal household use. Drawer
covers are not included. The drawers
can be exchanged at a GE
Sewice
and Parts Center, or by writing to the
address below.
This warranty is extended to the
original purchaser and any succeeding
owner for products purchased for
ordina~
home use in the 48 mainland
states, Hawaii and Washington,
D.C.
In Alaska the warranty is the same
except that it is LIMITED because you
must pay to ship the product to the
service shop or for the service
technician’s travel costs to your home.
Ail warranty service will be provided
by our Factory Service Centers or by
our Authorized Customer
Care@
servicers during normal working hours.
Should your appliance need service,
during warranty period or beyond, call
800-GE-CARES (800-432-2737).
WHAT IS NOT COVERED
● Sewice trips to your home to
teach you how to use the product.
Read your Use and Care
material.
If you then have any
questions about operating the
product, please contact your
dealer or our Consumer Affairs
office at the address below, or
call, toll free:
GE Answer
Cente@
800.626.2000
consumer information service
I
● Improper installation.
● Replacement of house fuses or
If you have an installation problem,
resetting of circuit breakers.
contact your dealer or installer.
● Failure of the product if it is used
You are responsible for providing
for other than its intended purpose
adequate electrical, plumbing and
or used commercially.
other connecting facilities.
Q
Damage to product caused
by accident, fire, floods or acts
of God.
● Loss of food due to spoilage.
WARRANTOR IS NOT
RESPONSIBLE FOR
CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
va~
from state to state
To know what your legal rights are in your state, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company
If further help is needed concerning this warranty, write:
Manager—Consumer Affairs, Appliance Park, Louisville, KY 40225
This book js
prjnted
on recycled paper.
Pati
No. 162
D7733POOI
Pub. No. 49-6775
Side by Side 20, 22, 24 and 27 Mode
Printed in
the United
state:
10-93
CG
Loading...