TM
SCB2000F – Advantium™ Wall Oven
Dimensions (in inches)
Cutout width |
4-3/16 |
|
|
|
|
||
28-1/2 |
|
|
|
15-27/32 |
19 |
|
|
Excluding |
|
||
Handle |
Cutout depth |
|
|
|
|
Junction |
|
|
|
box |
|
A |
B |
location |
|
|
|
||
21-7/8 |
21 |
|
|
Cutout height |
|
||
|
|
||
|
|
Construct Solid |
|
|
|
Bottom Min. |
|
29-25/32 |
Required |
3/8" Plywood |
|
Supported by |
|||
|
cutout location |
||
|
|
36-3/4" |
2 x 4 or 1 x 2 |
|
Runners, all |
||
minimum |
||
Four Sides. |
||
from floor |
||
(Must Support |
||
|
||
|
150 lbs.) |
|
30 |
|
A=Allow 1" overlap of oven over top and bottom edges of cutout. B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
Specification Revised 11/03
Note: Cabinets installed adjacent to wall ovens must have an adhesion spec of at least 194°F temperature rating.
Most 30" Wall Cabinets can be used with this unit.
Note: 2" minimum between cutouts when installed above warming drawer or single wall oven.
Listed by
Underwriters
R Laboratories
For answers to your Monogram,® GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
240428
TM
SCB2000F – Advantium™ Wall Oven
Single Speedcook Installation
30" |
19" |
|
Min |
||
|
||
|
28-1/2" |
21"
Construct Solid
Bottom Min. 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides
36-3/4" Min.
Required
Order a 30" wide single oven cabinet or cut the opening in a wall to dimensions shown.
The rough opening must be:
•Depth – 19" Min.
•Width – 28-1/2" Min.
•Height – 21" Min.
•36-3/4" from the floor to the cutout is required.
•These ovens require 3/4" overlap on each side, top and bottom of the cutout.
•Oven overlaps will conceal cut edges on all sides of the opening.
Specification Revised 11/03
Speedcook Oven Installation above a GE Warming Drawer
30" |
24" |
|
Min. |
||
|
||
|
28-1/2" |
21"
9-1/4"
36-3/4" Min.
Construct Solid
Bottom Min. 3/8"
Plywood Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides
2" Min.
Install 2 x 4 or 2 x 2
Runners or
Solid Bottom,
Must Support
100 lbs.
Note: Additional clearance between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location does not obstruct the required interior 23-1/2” depth and 9-1/4” height.
See installation instructions for details.
Speedcook Oven Installation above a single GE Built-In Wall Oven
30" |
24" |
|
Min. |
||
|
||
|
28-1/2" |
|
21" |
|
Construct Solid Bottom Min. 3/8" Plywood Supported by
2 x 4 or 1 x 2 Runners, all Four Sides
2" Min.
Per Oven
Requirement
*45-1/4"
|
Listed by |
|
Underwriters |
R |
Laboratories |
For answers to your Monogram,® GE Profile™ or GE appliance questions, visit our website at GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
240428