GE SCB2000CAA Specification
Specification Revised 10/00
SCB2000CAA - Advantium™Wall Oven
Dimensions (in inches)
• These ovens may be installed directly into a wall or wall oven cabinetry,
30" minimum width.
• The front surface of the oven will be nearly flush with surrounding cabinetry doors.
• This oven can be installed over any GE single electric built-in oven or a
single GE electric built-in warming drawer.
• This oven must be installed at least 36" above the floor.
IMPORTANT: This oven is not approved for use above another
built-in Speedcook oven, side by side or under the countertop
installations.
• For personal safety, this oven cannot be installed in a cabinet arrangement such as an island or peninsula.
• Cabinets installed adjacent to wall ovens must have an adhesion spec of
at least 194°F temperature rating.
• Allow for clearance to adjacent corners, walls, drawers, etc.
29-25/32"
15"
(Recessed
Portion)
21-7/8"
15-27/32"*
28-7/16"
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,
®
GE Profile Performance Series,
™
GE Profile™or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
27/32"
14-1/8"
15/32"
27/32"
20-27/32"
11/16"
7/8"
13"
9/16"
Single Speedcook Installation
Product rating is 120/208 or 120/240 volt, 60 Hz, 30 Amps. This product must be connected to a supply circuit
of the proper voltage and frequency and protected by a time delay fuse or circuit breaker. The power supply
should be brought to a separate 30 ampere branch circuit. Wire size must conform to the requirements of the
National Electric Code or the prevailing local code.
Combined Speedcook and Wall Oven Installation:
When installed in combination with a GE single wall oven, use separate electrical junction boxes,
OR,
Install a single junction box connected to 50 amp. supply circuit or properly rated supply circuit.
• Refer to single oven installation instructions for electrical requirements of
that product.
• These connections must be made by a qualified electrician. All electrical
connections must meet National Electrical code or prevailing local codes.
Combined Speedcook and Warming Drawer installation:
When installing the Speedcook oven over a GE electric warming drawer, a separate 120V, 60Hz,
properly grounded receptacle must be installed. See instructions packed with the warming drawer.
Electrical Requirements
Installation Requirements
*Excluding handle
SCB2000CAA - Advantium™Wall Oven
36-3/4" Min.
Required
30"
19"
Min
Construct Solid
Bottom Min. 3/8"
Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides
28-1/2"
21"
36-3/4" Min.
30"
24"
Min.
Construct Solid
Bottom Min. 3/8"
Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides
2" Min.
Install 2 x 4
or 2 x 2
Runners or
Solid Bottom,
Must Support
100 lbs.
28-1/2"
21"
9-1/4"
*45-1/4"
30"
24"
Min.
Construct Solid
Bottom Min. 3/8"
Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides
2" Min.
Per Oven
Requirement
28-1/2"
21"
Single Speedcook Installation
Order a 30" wide single oven cabinet or cut the opening
in a wall to dimensions shown.
The rough opening must be:
• Depth - 19" Min.
• Width - 28-1/2" Min.
• Height - 21" Min.
• 36-3/4" from the floor to the cutout is required.
• These ovens require 3/4" overlap on each side, top and
bottom of the cutout.
• Oven overlaps will conceal cut edges on all sides of
the opening.
Specification Revised 10/00
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,
®
GE Profile Performance Series,
™
GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.
Note: Additional clearance between the
cutouts may be required. Check to be sure
the oven supports above the Warming
Drawer location does not obstruct the
required interior 23-1/2” depth and 9-1/4”
height. See installation instructions for
details.
Speedcook Oven Installation above a single
GE Built-In Wall Oven
Speedcook Oven Installation above a
GE Warming Drawer
Loading...