GE SCA2000BBB User Manual

Specification Revised 11/99

R

Listed by
Underwriters
Laboratories

SCA2000BBB - GE Profile Performance™Advantium™Oven

Dimensional Information (in inches)

66" MIN.

Mounting

height

from
floor

30"

MIN.

width

required

Exhaust outlet

connects to

3-1/4" X 10" duct

16-3/32

20-1/2"

Door open

14-13/16

15-19/32

12"

MAX.

1. A minimum of 30” between the cabinets is required for the installation. If the space
between the cabinets is than 30”, a Filler Panel Kit may be used to fill the gap between
the oven and the cabinets. Your Owner’s Manual contains the kit number for your model.

2. Make sure the bottom edge of the cabinet that will be above the oven will be at least 66”
from the floor and 30” from the cooking surface.

3. For easier access to change the hood and range lamps, the bottom of the oven should be
at least 2” above the range backsplash.

4. If you are going to vent your oven to the outside, see exhaust duct
preparation instructions.

5. When installing the oven beneath smooth, flat cabinets, be careful to follow the
instructions on the top cabinet template for power cord clearance.

6. For best installation results, we recommend a maximum cabinet depth of 12”.

Installation Information: This information is not intended to be used for installing unit described.

Before installing, consult installation instructions packed with product/kit for current dimensional data.

For answers to your Monogram,

®

GE Profile Performance Series,

™

GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.

Electrical Requirements:

Product rating is 240/208 volts AC, 60 Hertz, 30 amps and 6.5 kilowatts. This
product must be connected to an individual properly grounded branch
circuit, protected by circuit breakers or time delay fuses. Wire size must
conform to the requirements of the National Electric Code or the prevailing
local code for kilowatt rating. The outlet box should be located in the cabinet
above the oven. The supply circuit and outlet box should be installed by a
qualified electrician and conform to all prevailing electrical codes. The wall
outlet receptacle recommended for this appliance is NEMA#14-30R and
accepts the four prong grounded plug of this appliance.

WARNING - PLEASE READ CAREFULLY.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID
SEVERE OR FATAL SHOCK.

DO NOT UNDER ANY CIRCUMSTANCES, CUT, DEFORM, OR REMOVE ANY OF THE
PRONGS FROM THE POWER CORD. DO NOT USE WITH AN EXTENSION CORD.

Insure proper ground
exists before use.

NEMA 14-30R
Wall Receptacle

Installation Requirements:

For answers to your Monogram,

®

GE Profile Performance Series,

™

GE Profile™or GE appliance questions, call
GE Answer Center®service, 800.626.2000.

R

Listed by
Underwriters
Laboratories

Specification Revised 11/99

SCA2000BBB - GE Profile Performance™Advantium™Oven

Hood Exhaust Duct

Outside ventilation requires a HOOD EXHAUST DUCT. Read the following
carefully.

EXHAUST CONNECTION:

The hood exhaust has been designed to mate with a standard 3-1/4” x 10”
rectangular duct.

If a round duct is required, a rectangular-to-round transition adaptor must be
used. Do not use less than a 6” diameter duct.

REAR EXHAUST:

If a rear or horizontal exhaust is to be used, care should be taken to align
exhaust with the space between studs, or wall should be prepared at the
time it is constructed by leaving enough space between the wall studs to
accommodate exhaust.

Duct Equivalent

A. Rectangular-To-Round 5 Ft.

Transition Adaptor

B. Wall Cap 40 Ft.
C. 90° Elbow 10 Ft.
D. 45° Elbow 5 Ft.
E. 90° Elbow 25 Ft.
F. 45° Elbow 5 Ft.
G. Roof Cap 24 Ft.

Grille

Filter Kit Accessory

Filter Kit
JX81A–Recirculating

Charcoal Filter Kit
To be used when

the Advantium oven
cannot be vented
to the outside.

MAXIMUM DUCT LENGTH:

For satisfactory air movement, the total duct length of 3-1/4” x 10” rectangular or
6” diameter round duct should not exceed 140 equivalent feet.

ELBOWS, TRANSITIONS, WALL AND ROOF CAPS, etc., present additional
resistance to airflow and are equivalent to a section of straight duct which is
longer than their actual physical size. When calculating the total duct length, add
the equivalent length of all transitions and adaptors plus the length of all straight
duct sections. The chart below shows the approximate feet of equivalent length of
some typical ducts.