GE SBSD227FGG, SBSD227FWW, WBVH6240F0GG, WBVH6240F0WW, WCVH6260F0GG Installation Guide
...
nstallation
Ilnstruct ons
Instructions en fran_ais : ............ 4
Instrucciones en espa_ol: ........... 8
SBSD227FWW
White Pedestal Base
For Washer Models: GBVH6260, GCVH6260,
WCVH6260, WBVH6240, WHDVH626
For Dryer Models: DCVH515, DHDVH52, DBVH512
SBSD227FGG
Granite Pedestal Base
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
• IMPORTANT - Savethese
instructions for local inspector's use.
• IMPORTANT - Observeall
governing codes and ordinances.
• Note to Consumer - Keep these
instructions with your Owner's Manual
for future reference.
• Completion time - 1 to 2 hours
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation
is not covered under the Warranty.
CAUTION - Due to the size and
weight of these products, and to reduce the
risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
• See washer and dryer installation
instructions for additional installation
requirements and guidelines.
KiT CONTENTS
4 Support Pads
4 Mounting Screws
TOOLS YOU WILL NEED
Phillips Head
Screwdriver
9/16" Open End Wrench
or Adjustable Wrench
8 mm Socket Wrench
INSTALLATION PREPARATION
Remove the packaging.
The Drawer divider is taped at the top of the
shipping carton. Remove the divider and set
aside for final installation.
Flatten the product carton to use as a pad
to lay the washer or dryer down on its side.
Continue using the carton to protect the finished
floor in front of the installation location.
17-1REMOVE THE LEVELING LEGS
[] Carefully lay the washer or dryer on its
side to access the leveling legs on the
bottom of the appliance.
IMPORTANT: Do not lay the washer or dryer
on its back! Do not remove the shipping
bolts on the back side of the washer. The
bolts must remain in place until the washer
is returned to an upright position.
[] Use an open-end wrench to remove the
washer or dryer leveling legs.
Drawer Divider
mnstaliation mnstructions
PREPARE THE PEDESTAL
[]
Pull the
[]
drawer out
as far as it
will go.
Remove
[]
screws from
drawer slides.
Slide drawer
out of the base
and set aside.
FOR DRYERS ONLY:
[] Locate the 4 support pads from the parts
package. Each pad has 2 protrusions that
fit into the holes on top of the pedestal.
Press the rubber pads into each set of
corner holes on the top of the pedestal
as shown.
iNSTALL THE PEDESTAL
TO THE WASHER OR DRYER
Place the pedestal against the bottom
[]
of the unit. Check to be sure the drawer
front is at the front of the washer.
AJign the holes in the pedestal with
[]
the holes in the bottom of the unit.
Use a PMHips screw driver to install
the 4 boks through the pedestaJ and
into the unit--do not tighten.
[] Slide the pedestal towards the unit, untit
it is aligned front to back. Use an 8 mm
socket wrench to securely tighten the
bolts.
NOTE: The support pads should be installed
on the dryer only. DO NOT INSTALL THESE
PADS ON THE WASHER PEDESTAL.
2
mnstaliation mnstructions
[_ LEVEL THE WASHER OR DRYER
Stand the washer or dryer upright. Move
[]
it close to its final location.
Make sure that the washer or dryer
[]
is level by placing a spirit level on top.
Check side to side and front to back.
[] Use an open
ended wrench
to adjust the
tegs in and
out. Tighten
the lock nut
against the
bottom of
the pedestal.
NOTE: To minimize vibration, the locking
nuts must be tight.
REINSTALL THE DRAWER
@
Check to
[]
be sure the
slides are
closed.
[_ REMOVE SHIPPING SCREWS
Remove the 4 shipping screws on the back side
of the washer.
[-_ FINALIZE THE INSTALLATION
Refer to the washer or dryer Installation
Instructions to complete the installation.
[] Slide the
drawer
into the Drawer
opening.
Align the
drawer
supports to
the slides on
each side.
[] Reinstall the original screws into each
drawer slide. Tighten both screws.
[] Open the drawer fully. Slide drawer
divider into slots in the center of the
drawer. The drawer should slide
smoothly when you push it closed.
divider
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
3
Instructions
d'installation
SBSD227FWW SBSD227FGG
Base-socle blanche Base-socle granite
Pour les modeles laveuses : GBVH6260, GCVH6260,
WCVH6260, WBVH6240, WHDVH626
Pour les modeles secheuses : DCVH515, DHDVH52,
DBVH512
AVANT DE COMMENCER
Lisez attentivement st en entier toutes ces
instructions.
, IMPORTANT - Cooservezces
instructionsa utiliserpar Finspecteur local.
°iMPORTANT - Observeztousles
codes et ordonnances en cours.
o Nots aU consom_rlateur - Conservez ces
instructionsavec votre manueJ du
proprietaire a titre de r@f@rence.
e DeJai d'execution - 1 a 2 heures
e Une bonne installation est ta responsabilite
de t'instalJateur.
Toute defaillance du produit suite a une
mauvaise installation n'est pas couverte
sous ta garantie.
_MISE EN GARDE - aoaueede
Ja taiHe st du poids de ees produits, et pour
reduire Je risque de bJessures personneHes
ou de dommages au produit, IL FAUT DEUX
PERSONNES POUR UNE BONNE
iNSTALLATiON.
Reportez-vous aux instructions
d'instattation de ta Javeuse et de Ja
secheuse pour Jes directives et exigences
supplementaires d'instattation.
OUTILS DONT VOUS AUREZ
BESOIN
Tournevis Phillips
Cle ouverte de 9/16 po
ou cle reglable
Cle a douille de 8 mm
PREPARATION DE L'INSTALLATION
Retirez I'emballage.
Le separateur de tiroir est colle dans le haut du
carton d'expedition. Retirez le separateur et
mettez-le de c6te pour I'installation finale.
Defaites le carton du produit pour I'utiliser
comme coussin ou deposer la laveuse ou la
secheuse sur le c6t& Continuez a utiliser le
carton pour proteger le plancher fini devant le
site d'installation.
CONTENU DE LA TROUSSE
4 coussinets de support
4 vis de montage
Separateur de tiroir
4
Loading...