GE SBSD137, SBSD227 User Manual
Installation
Instructions
KIT CONTENTS
4 Support Pads
4 Mounting Screws
Drawer Divider
1
SBSD137, SBSD227
TOOLS YOU WILL NEED
Phillips Head
Screwdriver
9/16″ Open End Wrench
or Adjustable Wrench
8 mm Socket Wrench
REMOVE THE LEVELING LEGS
Carefully lay the washer or dryer on its
side to access the leveling legs on the
bottom of the appliance.
IMPORTANT: Do not lay the washer or dryer
on its back! Do not remove the shipping
bolts on the back side of the washer. The
bolts must remain in place until the washer
is returned to an upright position.
Use an open-end wrench to remove the
washer or dryer leveling legs.
B
A
1
INSTALLATION PREPARATION
Remove the packaging.
The Drawer divider is taped at the top of the
shipping carton. Remove the divider and set
aside for final installation.
Flatten the product carton to use as a pad
to lay the washer or dryer down on its side.
Continue using the carton to protect the finished
floor in front of the installation location.
Back out and remove
all 4 leveling legs
Instructions en français : . . . . . . . . . . . .4
Instrucciones en español: . . . . . . . . . . .8
For Washer Models: GBVH5140, GBVH6260, GCVH6260, GCVH6600, GHDVH626,
GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600, WHDVH626
and WHDVH660
For Dryer Models: DBVH510, DBVH512, DCVH515, DCVH660, DHDVH52,
DHDVH66, PBVH415, PCVH565, PDVH515, PHDVH52 and PHDVH57
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•
IMPORTANT — Save these
instructions for local inspector’s use.
•
IMPORTANT — Observe all
governing codes and ordinances.
• Note to Consumer – Keep these
instructions with your Owner’s Manual
for future reference.
• Completion time – 1 to 2 hours
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation
is not covered under the Warranty.
CAUTION — Due to the size and
weight of these products, and to reduce the
risk of personal injury or damage to the
product, TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
• See washer and dryer installation
instructions for additional installation
requirements and guidelines.
2
Installation Instructions
INSTALL THE PEDESTAL TO THE WASHER OR DRYER
Place the pedestal against the bottom
of the unit. Check to be sure the drawer
front is at the front of the unit.
Align the holes in the pedestal with
the holes in the bottom of the unit.
Use a Phillips screwdriver to install
the 4 screws through the pedestal
and into the unit—do not tighten.
Slide the pedestal toward the unit,
until it is aligned front to back. Use an
8 mm socket wrench to securely tighten
the screws.
C
B
A
3
PREPARE THE PEDESTAL
Pull the
drawer out
as far as it
will go.
Remove
screws from
drawer slides.
Slide drawer
out of the base
and set aside.
FOR DRYERS ONLY:
Locate the 4 support pads from the parts
package. Each pad has 2 protrusions that
fit into the holes on top of the pedestal.
Press the rubber pads into each set of
corner holes on the top of the pedestal
as shown.
NOTE: The support pads should be installed
on the dryer only. DO NOT INSTALL THESE
PADS ON THE WASHER PEDESTAL.
C
B
A
2
3
Installation Instructions
LEVEL THE WASHER OR DRYER
Locate the 4 legs from the parts package
and install.
Stand the washer or dryer upright. Move
it close to its final location.
Make sure that the washer or dryer
is level by placing a spirit level on top.
Check side to side and front to back.
Use an open
ended wrench
to adjust the
legs in and
out. Tighten
the lock nut
against the
bottom of
the pedestal.
NOTE: To minimize vibration, the locking
nuts must be tight.
D
C
B
A
4
REMOVE SHIPPING SCREWS
Remove the 4 shipping screws on the back side
of the unit.
6
REINSTALL THE DRAWER
Check to
be sure the
slides are
closed.
Slide the
drawer
into the
opening.
Align the
drawer
supports to
the slides on
each side.
Reinstall the original screws into each
drawer slide. Tighten both screws.
Open the drawer fully. Slide drawer
divider into slots in the center of the
drawer. The drawer should slide
smoothly when you push it closed.
D
C
B
A
5
FINALIZE THE INSTALLATION
Refer to the washer or dryer Installation
Instructions to complete the installation.
7
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Drawer
divider
Instructions
d’installation
CONTENU DE LA TROUSSE
4 coussinets de support
4 vis de montage
Séparateur de tiroir
4
AVANT DE COMMENCER
Lisez attentivement et en entier toutes ces
instructions.
•
IMPORTANT — Conservez ces
instructions à utiliser par l’inspecteur local.
•
IMPORTANT — Observez tous les
codes et ordonnances en cours.
• Note au consommateur – Conservez ces
instructions avec votre manuel du
propriétaire à titre de référence.
• Délai d’exécution – 1 à 2 heures
• Une bonne installation est la responsabilité
de l’installateur.
• Toute défaillance du produit suite à une
mauvaise installation n’est pas couverte
sous la garantie.
MISE EN GARDE — à cause de
la taille et du poids de ces produits, et pour
réduire le risque de blessures personnelles
ou de dommages au produit, IL FAUT DEUX
PERSONNES POUR UNE BONNE
INSTALLATION.
• Reportez-vous aux instructions
d’installation de la laveuse et de la
sécheuse pour les directives et exigences
supplémentaires d’installation.
SBSD137, SBSD227
OUTILS DONT VOUS AUREZ BESOIN
Tournevis Phillips
Clé ouverte de 9/16 po
ou clé réglable
Clé à douille de 8 mm
PRÉPARATION DE L’INSTALLATION
Retirez l’emballage.
Le séparateur de tiroir est collé dans le haut du
carton d’expédition. Retirez le séparateur et
mettez-le de côté pour l’installation finale.
Défaites le carton du produit pour l’utiliser
comme coussin où déposer la laveuse ou la
sécheuse sur le côté. Continuez à utiliser le
carton pour protéger le plancher fini devant le
site d’installation.
Pour les modèles laveuses : GBVH5140, GBVH6260, GCVH6260, GCVH6600,
GHDVH626, GHDVH670, WBVH5100, WBVH6240, WCVH6260, WCVH6600,
WHDVH626 et WHDVH660
Pour les modèles sécheuses : DBVH510, DBVH512, DCVH515, DCVH660,
DHDVH52, DHDVH66, PBVH415, PCVH565, PDVH515, PHDVH52 et PHDVH57
Loading...