GE RM24948 User Manual

RM24948

Universal Remote Instruction Manual

Table of Contents

Setup

Introduction ........................................................... 3

Setup .................................................................... 3

Battery Installation ........................................... 3

Battery Saver ................................................... 3

Code Saver ...................................................... 3

Code Setup ...................................................... 3

Button Functions ............................................. 4

Code Entry using the Code List ....................... 5

Code Search .................................................... 6

Using Your Remote ............................................... 7

Code Retrieval .................................................. 7

Controlling Devices with Power On and Off ...... 8

Controlling Combo Devices .............................. 8

VCR/DVD/DVR Punch-Through ....................... 8

Volume/Mute Control and Punch-Through ........ 8

All Volume/Mute Control to any one Mode ....... 9

Returning Volume/Mute Control to Initial Default ... 9

Troubleshooting .................................................. 10

Congratulations on your purchase of the RM24948 Universal Remote Control. The RM24948 is one of the most easy to use remote controls available today. With the RM24948, juggling multiple remote controls is a thing of the past! Your RM24948 controls up to three devices, including the most popular brands of TV, VCR, DVD, CBL, and SAT. The RM24948 is easy to use, easy to program, and it gives you total control—at the touch of your fingertips!

Note: Some functions from your original remote may not be controlled by this remote. Use the original remote, if available, to control such functions. Sometimes buttons other than described in these instructions may actually perform the function. We recommend you experiment with the remote to identify if such situations pertain to your equipment.

Battery Installation

1. On the back of the remote, push down on the tab and lift the cover off.

2. Match the batteries to the + and - marks inside the battery case, then insert 2 AAA Alkaline batteries.

3. Press the battery cover back into place.

Battery Saver

Your remote automatically turns off if the buttons are depressed more than 30 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).

Code Saver

You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed. However, do not press any buttons until batteries are installed in the remote. If buttons are pressed without batteries in the remote, all codes will be lost.

Code Setup

The SETUP button is used to setup the remote. You can either setup the remote using the code tables (on separate sheet), or you can search through the library of codes until you find a code that works for your product. Please refer to “ Code Search” on page 6 for more information on using the code search feature to learn how to search through the library of codes for your products. NOTE: You can store any kind of code under any mode (except TV). I.E. you can store a VCR code under the CBL/AUX button, or a Cable code under the VCR/DVD button, etc. However, you can only store TV codes under the TV button.

Button Functions Code Entry using the Code List

POWER Turns product On or Off.

Red Indicator Lights when any button is pressed.

SETUP Used to setup

the remote, and for

code search function.

TV, CBL/AUX, VCR/DVD

Selects product to be

CHANNEL Up/Down

Changes the channels.

Also controls DVD SKIP

MUTE Turns off the

TV sound, while the

VOLUME UP/DOWN

Changes the volume

level of the product,

RECORD, PLAY, STOP,

REW, FF, PAUSE VCR/DVD

control buttons operate

your VCR or DVD even

when the remote is set to

operated.

functions.

picture remains.

normally the TV.

operate the TV.

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.

2. Press and release the desired device button (TV, VCR/DVD, etc.). The red indicator blinks, then stays lit.

3. Enter the 4 digit code for your brand of TV, VCR, etc., from the Library Code Table by using the CH-, V-, CH+ and V+ buttons.

Use the CH- button to enter the first digit. Use the V- button to enter second digit. Use the CH+ button to enter the third digit. Use the V+ button to enter the fourth digit.

For Example: To enter code 0107, don’t press CH-, press V- once, don’t press CH+ and press V+ seven times. The red LED blinks off with each keypress.

4. Press the MUTE button to save the code.

Note: for a valid code, the red LED turns off. For an invalid code, the red LED blinks rapidly for three seconds before going off.

Note: The REC button must be pressed TWICE to record from your VCR. For some brands of VCRs, you might need to press the REC button once, then press it again for three seconds.

5. With your device on, press POWER. If the device turns off, no further programming is required. Note: If some buttons do not operate your equipment, try one of the other codes for your brand.

+ 4 hidden pages