GE JGBS04PPT1WW, JGBS06PPM5CT, JGBS04PPM5WW, AGBS300PK6BB, JGBS06PPM5WH Supplementary Manual
...
L.P. CONVERSION
INSTRUCTIONS
WARNING:
Thisconversionmust be performed
bg a qualified installeror gas supplier
in accordancewith the
manufacturer'sinstructionsandall
codesand requirementsof the
authority havingjurisdiction. Failure
to followALLinstructionscould result
in seriousinjury or property
damage.Thequalified agency
performingthis work assumes
responsibilityfor the conversion.
The pressure regulator and the burner
orifices are set for natural gas. To use
Liquid Propane Gas,the regulator and
burner orifices must be converted. The
L.Rorifices for the cooktop burners are
shipped on the regulator bracket behind
the storage drawer. Also,inthe same
area, is a second bracket holding the L.R
!5K orifice extended spud, choke and set
screw for the front right Extra Large
cooktop burner (on models so equipped).
Remove the storage drawer to locate.
A WARNING:
Do not operate the cooktop or oven
burners of this range when using L.R
(bottled) gas before converting the
pressure regulator and burner orifices
for L.Rgas use.Failure to do so could
cause high flames and toxic fumes
which can result in serious injury.
Toadjust yourrangefor usewith L.Rgas,
followthese instructions:
!. Disconnectallelectricalpower,at the
maincircuit breakerorfusebox.
2.Shutoff thegassupply to therange bg
closingthe manual shut-off valve.
a. Raisethe cooktop and locate the
pressure regulator.
b. Follow the direction in 1Aor 1B
depending on your regulator
type.
NOTICE:
tf youareusingL.P.(bottled)gas,all
adjustments describedinthe
following stepsmustbe madebefore
youmakeany burner adjustments.
\
/
GasFIow
IntoRange
\\\\\
\\\_.
---- ........ JJ
Regulator pictured may be differ
from your model.
1A-IF THIS IS YOURREGULATOR
(LP/Propane)
Nut&Pin
GasFIow
IntoRange NAT
a. Use an adjustable wrench to
remove the hex-nut from the
pressure regulator.
b. Apply sideward finger pressure to
remove the plastic pin from the
nut.
Note: Toremove the pin, place
the nut on a flat surface and
press the pin sidewags with gour
fingers.
c. Rotate the pin 180 degrees and
snap the pin back into the nut.
NAT _ (LP/Propane)
d. Reinsert the assembly into the
regulator and tighten the hex-nut.
(Do nor over tighten}
1B-IF THIS IS YOUR REGULATOR
a. Use an adjustable wrench to
unscrew the hex-nut cap from
the pressure regulator.
b. Apply pressure and turn counter
clockwise to disassembly the
plastic cap.
c. Turn the cap over and hook it into
the slots.The type of gas to be
used should now be visible in the
top of the cap.
d. Screw back the hex-nut cap into
the pressure regulator.
a.
b.
c.
Lift the burner assemblies
straight up (setaside)to gain
access to the surface burner
orifice spuds.
Using a 5/16" nut driver or
adjustable wrench, remove each
of the four (4)spuds on the
surface burner gas inlet tubes.
Replace them with the correct
gas spuds mounted in a holder
at the right rear ofthe range,
above the regulator. (Natural
gas spuds are "BRASS"and LP
gas spuds are "SILVER")
NOTICE:
Save these orifices forfuture
conversion back to natural gas.
J
d.
Return the spuds you removed
from the inlet tubes to the holder
above the regulator. (Toprevent
leakage, make sure the spuds
are securelg screwed into the
gas inlet tubes).
e. Replace the burner assemblies.
a. Remove all five (5)knobs,
including OVENCONTROLknob.
Remove the four (4) screws
located behind the two (2)inner
cooktop knobs.
b. Open the oven door. Remove the
three (3)screws located under
the mainfold panel. Remove the
mainfold panel.
c. Located the thermostat bypass
screw below the thermostat
shaft.Completely loosen the
natural gas bypass screw (blue)
by turning it counterclockwise.
Remove it by gently pulling it out
using pliers.
d. Replace with the LPbypass screw
(white) located in the envelope
near the rear of the range, above
the pressure regulator. Tighten
the screw by turning it
clockwise.
Turn Screws Counter clockwise to
loosen
e.
Bypass Pilot
Screw Flame
Screw
Located the thermostat pilot
flame screw to the right of the
thermostat shaft.
Completely LPorNat
loosen the natural
gas pilot screw (red)
by turning it
counterclockwise
Bypass and Pilot
Remove it by gently F_...... ewslook
pulling it out using s_m_ar,p_e......
chart below for
Pliers. correct screw
f. Replace with the LPpilot screw
(black) located in the envelope
near the rear of the range,
above the pressure regulator.
Tighten the screw by turning it
clockwise.
g. Replace manifold panel and
knobs.
GAS TYPE SCREW TYPE COLOR
Natural Gas Bypass Blue
Natural Gas Pilot Red
LP (Propane} Bypass White or Green
LP (Propane} Pilot Black
1
.
BAKE / BROIL BURNER ORIFICE
Remove oven door, drawer and
oven bottom. The lower burner
orifice hood is located behind
the drawer (on some models a
metal shield must be removed).
To convert to LP,use a !/2"
wrench to turn the lower burner
orifice hood clockwise (When
viewed from above) until it is
snug with the base,
approximately 2 1/2 turns.
(To prevent damage when
converting back to Natural Gas,
do not over tighten the hood.)
Theoven bake burner assembly is
located at the lower rear
compartment.
A metal shield may need to be
removed on some models to access
the orifice hood.
AIR SHUTTER SETTINGS FOR
BAKE AND BROIL BURNERS
1. Use a screwdriver to loosen
.
.
the air shutter screw.
Adjust the air /
J
shutters sc
for LP gas, A_rS_
bg rotating
the shutter to the fulk
open
position. For natural gas, the
shutter should be open _½"or
about 3/4" of the wag open.
Your final settings may vary.
Retighten the air shutter
screw.
NOTICE:
Makesurethe surface burnercontrol
knobsare inthe OFFpositionbefore
attempting to lightthe pilots
Bake and broil flume must be
checked with the door closed to
properlg check flume
characteristics.
4. Turn on the gas.
5. Turn on the electricity.
6. Reinstall the oven door.
7. Light both surface burner
pilots with a match.
8. To avoid pilot outage, use
caution when closing the
cooktop after lighting pilots.
31-21460
DUAL
ADJUSTING THE SURFACE
BURNER PILOTS
1. Locate the pilot adjustment
screw. It can be accessed
through the small hole near
the center of the manifold
panel.
2. To adjust, use a flat-blade
screwdriver with a shaft
diameter of less than 3/16".
Turn the pilot adjustment
screw until the pilot is 5/16"
high.Do not reduce the flame
to less than 5/16" or a pilot
outage mag occur. A pilot
flame burning higher than
recommended mag generate
soot {carbon black) on the
bottom of the cooktop.
LIGHTING THE OVEN PILOT.
1. Locate the pilot
in the back of the
oven bottom._
The pilot is ,<__f;I,_____X
attached to }_'_ _ \
the left side J_q !
of the oven burner.
2. To light the oven pilot, push in
and hold the oven control
knob while lighting the pilot
with a long match or match
holder.
.
Once the oven pilot is lit,
continue holding the oven
control knob for one minute
before control knob for one
minute before releasing.
The pilot flame size should be
approximatelg 3/8 for LP and
1_ for natural gas.
CHECKING THE FLAME SIZE
1t,WARNING:
tf gou attempt to measure
the inner cone of the flame, please
use caution; burns could result.
1. Checking the flame size:
Check the inner cone of the flame.
It should be approximatelg 1W'to
sA" long for the bake and broil
burners.
_ r_INNER CONE
OF FLAME
1/2 " to 3/4" _1/_4_ OVEN / BROIL
CHECKING THE FLAME QUALITY
The combustion quolitg of the
burner flames need to be
determined visuallg.
NOTE: If burner flames look like
{A}. Further air shutter adjust-
ment is required. Normal burner
flames should look like (B) or (C},
depending on the type of gas
you use. With LP gas, some
yellow tipping on the outer
cones is normal.
IA) Yellow Flames:
Further Adjustment
Required
IB) Yellow tips on
outer cones:
Normal for LP Gas
(el Soft Blue Flames:
Normal for Natural Gas.
When all adjustments are mode
and the results are satisfactorg:
a. Replace the orifice fitting cover.
b. Replace the oven baffle (flame
spreader).
c. Replace the oven bottom.
IN SOME CASES:
a. With L.R gas, some gellow
tipping on the outer cone is
normal.
b. Foreign particles in the gas line
mag cause on orange flame at
first, but this will soon disappear.
SPECIALNOTE:
To convert the oven beck to natural
gas, reverse the instructions given in
making L.P.Adjustments.
REPLACEOVEN PARTS
Replace the oven bottom, oven racks,
oven door and broil drawer.
NOTICE:
Once the conversion is complete and
checked ok, fill out the L.RSticker
and include gour name, organization
and date conversion was made.
Applg the sticker to the range near
the regulator to alert others in the
future that this appliance has been
converted to L.R tf converting back
to natural gas from L.R,please
remove the sticker so others know
the appliance is setto use natural
gas.
BURNER OUTPUT RATINGS:
BTU/HR
BTU
ORIFICE SIZE
BURNER RATE
RF 8,000 #66 (.0330 Dia.}
LF 8,000 #66 (.0330 Dia.}
LR 8,000 #66 (.0330 Dia.}
RR 8,000 #66 (.0330 Dia.}
BAKE* 16,000 #56 (0.0465"}
+BROIL* 12,000 #59 (0.041")
+ Ifso equipped.
* Oven burner(s) use convertible
hood(s)and are simplg adjusted for
conversion.
LPGAS NATURAL GAS
Spud is Silver Spud is Brass
BURNER OUTPUT RATINGS:
BTU/HR
BTU
BURNER RATE COLOR
RF 9,100 #53 (.0590 Dia.)
LF 9,100 #53 (.0590 Dia.}
LR 9,100 #53 (.0590 Dia.}
RR 9,100 #53 (.0590 Dia.}
BAKE* 16,000 #48 (0.076")
BAKE* 18,000 #46 (0.081")
+BROIL* 12,500 #51 (0.067'1
~ForStandard models.
+ Ifso equipped.
* Oven burner(s) use convertible
hood(s)and are simplg adjusted for
conversion.
TOOLS REQUIRED:
Adjustable wrench
W' open-end wrench
Phillips head screwdriver
Flat bladed screwdriver (blade
width approximatelg 3/32"
across)
Nut drivers: 9/32" or 7mm
L.R CONVERSION
INSTRUCTIONS
183D5578P095
31-21460
DUAL
04-09 CR
Loading...