GE RCE25RGBFKB, GSE25MGYCWW, PSE25VGXCWW, GIE21XGYFKB, GCE21XGYFWW User guide

200D2600P058 49-60565-1 02-09 JR

La section française commence à la page 39

La sección en español empieza en la página 73

Safety Instructions . . . . . . . . . . .2, 3

For Australia and New Zealand . . . . .34

Operating Instructions

Additional Features . . . . . . . . . . . . . . . .11

Automatic Icemaker . . . . . . . . . . . . . . .15

Care and Cleaning . . . . . . . . . . . . .17, 18

Crispers and Pans . . . . . . . . . . . . . . . . .14

CustomCool

™

. . . . . . . . . . . . . . . . . . .4, 7, 8

Freezer Compartment . . . . . . . . . . . . .13

Ice and Water Dispenser . . . . . . .16, 17

Refrigerator Doors . . . . . . . . . . . . . . . . . .9

Replacing the Light Bulbs . . . . . . . . . .19

Shelves and Bins . . . . . . . . . . . . . . .10–12

Temperature Controls . . . . . . . . . . . . .4–6

TurboCool

™

. . . . . . . . . . . . . . . . . . . . . . . . .6

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . .9

Installation Instructions

For Australia and

New Zealand . . . . . . . . . . . . . . . . . . .35–37

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . .25–27

Removing and Replacing Doors . . . . .24

Trim Kits and Panels . . . . . . . . . . . .20–23

Water Line Installation . . . . . . . . .28, 29

Troubleshooting Tips . . . . . .31–33

Normal Operating Sounds . . . . . . . . . .30

Réfrigérateurs

Côte à Côte

Frigoríficos

Lado a Lado

Models 21, 23, 25, 27 and 29

Write the model and serial numbers here:
Model # __________________________

Serial # __________________________

Find these numbers on a label inside
the refrigerator compartment at the
top on the right.

Owner’s Manual and Installation

Manuel d’utilisation et d’installation

Manual del propietario e instalación

Refrigerators

Side-by-Side

La sezione in italiano inizia alla pagina numero 109

Frigoriferos

Da un lato all’altro

Manuale del proprietario e d'installazione

O capítulo em português tem início na página 145

Frigoríficos

Lado a Lado

Manual do Proprietário e Instalação

Die deutsche Anleitung befindet sich auf Seite 179

Kühlschränke

Doppelseitige

Bedienungsanleitung und Installation

Instructies in het Nederlands vindt u vanaf pagina 213

Koelkasten

‘Side-by-side’

Handleiding en installatie-instructies

To ∂ППЛУИОfi ОВК¿П·ИФ ·Ъ¯›˙ВИ ЫЩЛ ЫВП›‰· 247

æ˘Á›·

Side by Side

∂Á¯ÂÈÚ›‰ÈÔ ÃÚ‹ÛÙË Î·È ∂ÁηٿÛÙ·Û˘

2

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation
Instructions before it is used. Also see the
How to Connect Electricity section.

■

■ Do not allow children to climb, stand or hang on

the shelves in the refrigerator. They could damage
the refrigerator and seriously injure themselves.

■

■

Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold surfaces.

■

■

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

■

■ In refrigerators with automatic icemakers, avoid

contact with the moving parts of the ejector
mechanism, or with the heating element located
on the bottom of the icemaker. Do not place fingers
or hands on the automatic icemaking mechanism
while the refrigerator is plugged in.

■

■ Installation of the icemaker must be done by

a qualified service technician.

■

■ This appliance is not intended for use by persons

(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.

■

■ Children should be supervised to ensure that they do

not play with the appliance.

■

■

Keep fingers out of the “pinch point” areas;
clearances between the doors and between the
doors and cabinet are necessarily small. Be careful
closing doors when children are in the area.

■

■ Unplug the refrigerator before cleaning and making

repairs.

NOTE: We strongly recommend that any servicing
be performed by a qualified individual.

■

■ Before replacing a burned-out light bulb, the

refrigerator should be unplugged in order to avoid
contact with a live wire filament. (A burned-out light
bulb may break when being replaced.)

NOTE: Setting either or both controls to 0 (off) does
not remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

■

■ Always clean the CustomCool™Tray after

thawing food.

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous…even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.

Before You Throw Away Your Old
Refrigerator or Freezer:

■ Take off the doors and discard separately.

■ Leave the shelves in place so that children may

not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the company
handling the disposal about what to do.

3

WARNING!

HOW TO CONNECT ELECTRICITY

The power cord of this appliance is equipped with
an earthing plug which mates with a standard
earthed wall outlet to minimize the possibility
of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly earthed.

Where an unearthed wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly earthed wall outlet.

The refrigerator should
always be plugged into
its own individual
electrical outlet.
This provides the
best performance
and also prevents
overloading house
wiring circuits which could cause a fire hazard from
overheated wires. Please refer to the rating plate on
the refrigerator for the correct voltage, wattage and
frequency. If the product plug does not fit your outlet,
the product should be fitted with a new plug.

IMPORTANT: The refitting of electric plugs and cables
should be done by a qualified technician or service
agent. In some countries the refitting of electric plugs
and cables is only permitted when the work is
completed by a qualified technician.

If the power supply cord becomes damaged, it must
be replaced by a qualified service agent in order to
avoid a safety hazard.

Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet.

Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.

When moving the refrigerator away from the wall,
be careful not to roll over or damage the power cord.

Mains lead replacement

If the mains lead on your refrigerator needs replacing
at any time, it must be replaced by a special lead
which is obtainable from your local dealer. A charge
will be made for the replacement of the mains lead
if you have damaged the lead.

The refrigerator must be positioned so that the plug
is accessible.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Insure proper earthing
exists before using.

Earthing plug

NOTES ON THE CONTAINMENT OF FLUORINATED GREENHOUSE GASES

Contains fluorinated greenhouse gases covered by the Kyoto Protocol.
Gas: R134a (HFC-134a), GWP (Global Warming Potential) = 1300

Hermetically sealed.

The amount of R134a gas in this product is:

0.127–0.184 kg

4

About the temperature controls – Profile Models. ge.com

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not

removed during installation, remove it now.

The temperature controls are preset in the factory at 37°F (3°C)
for the refrigerator compartment and 0°F (-18°C) for the freezer
compartment. Allow 24 hours for the temperature to stabilize
to the preset recommended settings.

Refrigerator temperatures can be adjusted between 34°F and 46°F
(1°C to 8°C), and the freezer temperatures can be adjusted between
–6°F and +8°F (–21°C to –13°C).

To change the Refrigerator temperature:
LCD Models:
Access By: Home > Refrigerator
Activate By: Using the arrows to select the desired

temperature. You must press ENTER to set the new
temperature.

To change the Freezer temperature:
Access By: Home > Freezer
Activate By: Using the arrows to select the desired

temperature. You must press ENTER to set the new
temperature.

Once the desired temperature has been set, the display will
return to the HOME screen and show the set temperatures
underneath the actual temperature display for several
seconds. Several adjustments may be required. Each time you
adjust the controls, allow 24 hours for the refrigerator to reach
the temperature you have set.

Non-LCD Models:
To change the temperature, press and release the FREEZER

TEMP/FRIDGE TEMP pad. The SET light will come on and

the display will show the set temperature. To change the
temperature, tap either the or pad until the desired
temperature is displayed.

Once the desired temperature has been set, the temperature
display will return to the actual refrigerator and freezer
temperatures after 5 seconds. Several adjustments may be
required. Each time you adjust the controls, allow 24 hours
for the refrigerator to reach the temperature you have set.

The temperature controls can display both the SET temperature
as well as the actual temperature in the refrigerator and freezer.
The actual temperature may vary slightly from the SET temperature
based on usage and operating environment.

Turning the cooling system off:
LCD models: Turning the cooling system OFF stops cooling in both

the freezer and refrigerator compartments, but does not shut off
electrical power to the refrigerator.

LCD Models:
Access By: Home > Options > Information and Settings >

Cooling System Off
To turn the cooling system back on, press the touch screen

and press the ON button.

Activate By: Pressing ENTER.
Non-LCD Models:

Press and release the FREEZER TEMP/FRIDGE TEMP pad.
Press to set freezer temperature to 5. The display will
show OFF. To turn the unit back on, press the FREEZER
TEMP/FRIDGE TEMP pad. Press to set the freezer and
refrigerator temperatures to the preset points of 0°F (-18°C)
for the freezer and 37°F (3°C) for the refrigerator.

When the unit is turned back on, it will take up to 24 hours
to stabilize.

LCD Models: Units

The LCD models are shipped from the factory with default
settings of English units.

To change to Metric units, select:
Home>Options>Information and Settings>Settings>Units
Metric/English>Metric.
To change back to English units repeat the above steps and

select English at the final step.
NOTE: The help screen has default setting for US and Canada

customers. If you need replacement parts, contact your local
distributor.

LCD models

Non-LCD models Non-LCD models

Not all features are on all models. Your controls will look like one of the following:

>

>

>

>

5

About the temperature controls – GE, Monogram Models.

The temperature controls are preset in the factory at 5 for both the refrigerator and
freezer compartments.

To adjust the set point temperature, press the WARMER or COLDER button on either the
Freezer or Refrigerator side. The set point light will come on. Press WARMER or COLDER
until the desired setting is reached.

Several adjustments may be required. Each time you adjust controls, allow 24 hours
after each adjustment for the refrigerator to reach the setting you have selected.

Setting either or both controls to 0 stops cooling in both the freezer and refrigerator
compartments, but does not shut off electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating
conditions and may require more than one adjustment.

NOTE: The refrigerator is shipped with protective film covering the temperature controls.

If this film was not removed during installation, remove it now.

This refrigerator is designed to operate in ambient temperatures
specified by its Temperature Class, which is marked on the rating plate.

Temperature Symbol Ambient Temperature
Class Maximum Minimum

Extended­Temperate SN 32°C 10°C

Temperate N 32°C 16°C
Subtropical ST 38°C 16°C
Tropical T 43°C 16°C

NOTE: Internal temperature may be affected by such factors as the location of the refrigerator,
ambient temperature and frequency of door openings. Adjust temperature controls as required
to compensate for these

factors.

The unit will have one of the temperature controls shown below:

Internal Temperature

Controls

External Set Point

Controls (0-9)

GE Models

Ambient temperature limits

6

About TurboCool.

™

How it Works

TurboCool™rapidly cools the refrigerator

compartment in order to more quickly
cool foods. Use TurboCool when adding
a large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature or
when putting away warm leftovers. It can also
be used if the refrigerator has been without
power for an extended period.

Once activated, the compressor will turn
on immediately and the fans will cycle on
and off at high speed as needed for eight
hours. The compressor will continue to run
until the refrigerator compartment cools
to approximately 34°F (1°C), then it will cycle
on and off to maintain this setting. After
8 hours, or if TurboCool is pressed again,
the refrigerator compartment will return
to the original setting.

How to Use
LCD Models:

Access By: Home > Options > Refrigerator

Options > TurboCool

Activate By: Pressing ON.
Deactivate By: Pressing OFF.

Non-LCD Models:

Press SET FEATURES. The refrigerator
temperature display will show TurboCool
and/or TC. Press ON/OFF.

Internal Control Models:

Press TurboCool. The TurboCool indicator
light will come on. After TurboCool is complete,
the TurboCool indicator light will go out.

After TurboCool is complete, the refrigerator
compartment will return to the original setting.

NOTES:

The refrigerator temperature cannot be changed
during TurboCool.

The freezer temperature is not affected during
TurboCool.

When opening the refrigerator door during
TurboCool, the fans will continue to run if they
have cycled on.

About ClimateKeeper2.

™

(on some models)

How it Works

The ClimateKeeper2™is the industry’s
most advanced refrigeration system,
delivering optimum temperature and
humidity performance to keep food garden
fresh longer and reduce freezer burn, while
maintaining efficiency.

The ClimateKeeper2 system features two
evaporators—one for the refrigerator and
one for the freezer.

This provides two separate cooling systems,
and separates the airflow between the fresh
food and freezer compartments during normal
cooling operations.*

This ensures that the humidity levels in
the fresh food compartment are significantly
higher than in a conventional system,** allowing
fresh produce and other unsealed foods to retain
their moisture content and freshness longer.
Moisture sensitive foods such as fresh fruit,

salads, rice, etc., can now be stored on open
shelves without excessive moisture loss. Due to
the higher humidity in the refrigerator, you may
on occasion experience fog or small amounts of
moisture in the refrigerator compartment. This is
normal and may come and go as different food
loads and environmental conditions change.
Wipe dry with a paper towel if desired.

The separate airflow system minimizes the mixing
of air between the two compartments, which
reduces fresh food odor transfer to improve
the taste of ice.

The ClimateKeeper2 system also reduces
the number of defrosting cycles in the freezer
evaporator, thereby reducing freezer burn.

*Freezer air is used in the CustomCool feature.
**Testing shows a higher level of humidity in

the Fresh Food section in ClimateKeeper2
refrigerators versus conventional units.

About Set Features.

This pad is used to select the following
features: TurboCool, Quick Ice, Door Alarm
and Water Filter.

Pressing SET FEATURES repeatedly will cycle
through all of the available features and then

exit the mode. If no key is pressed, the mode
will exit and return to displaying features
currently set.

7

Empty the pan. Place the Chill/Thaw tray

in the pan. Place the items on the tray

and close the pan completely.

LCD Models:
Access by: Home > Options > Refrigerator

Options > CustomCool Pan
Non-LCD Models:

Select the ExpressThaw

™

, ExpressChill

™

or SelectTemp™pad. The display and SET light
will come on. Tap the pad until the light
appears next to the desired setting.

Use the following chart to determine the best
setting to use.

■ ExpressChill can be set to 15, 30 or 45

minutes. The default is 15 minutes.

■ To stop a feature before it is finished:

For LCD Models:

Go into that feature’s menu and press
the OFF button.

For Non-LCD Models:

Tap that feature’s pad until no options
are selected and the display is off.

■ During ExpressThaw and ExpressChill,

the display on the controls will count down
the time in the cycle (on some models).

■ After the ExpressThaw cycle is complete,

the pan will reset to the MEAT setting
(32°F [0°C]) to help preserve thawed
items until they are used.

■ The displayed actual temperature of

the CustomCool pan may vary slightly
from the SET temperature based on
usage and operating environment.

NOTE: For food safety reasons, it is recommended
that foods be wrapped in plastic wrap when using
ExpressThaw. This will help contain meat juices
and improve thawing performance.

About CustomCool™. (on some models)

The CustomCool™feature is used to quickly chill
items, thaw items or hold the pan at a specific
temperature. This feature is a system of dampers,
a fan, a temperature thermistor and a heater.

The pan is tightly sealed to prevent
temperature fluctuations in the rest of
the refrigerator. The controls for this pan
are located on the dispenser with the
temperature controls.

How to Use

ExpressThaw

™

To remove:

Pull the drawer out to the stop position.
Rotate all four swing locks to the unlock

position.

Lift the front of the drawer up and out.

To replace:

Make sure all four swing locks are

in the unlock position.

Place the sides of the drawer into

the drawer supports, making sure

the swing locks fit on the drawer slots.

Lock all four swing locks by rotating them

to the lock position.

How to Remove and Replace the Drawer

ExpressChill

™

LCD Models Only

Non-LCD Models Only

How it Works

LCD Models OnlyOR

REFRIGERATOR OPTIONS

CUSTOM COOL

PAN

BEVERAGE

CENTER

BACK

TURBOCOOL

8

About CustomCool.

™

(on some models)

CustomCool™ Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

0.25 kg (4 hours)

■ Hamburgers (0.25 kg)

■ Individually Wrapped

Filet Mignon (0.25 kg)

0.50 kg (8 hours)

■ Chicken Breasts (0.5 kg)

■ Minced Beef (0.5 kg)

■ Steak (0.5 kg)

1.0 kg (10 hours)

■ Chicken Breasts (1.0 kg)

■ Minced Beef (1.0 kg)

■ Steak (1.0 kg)

1.50 kg (12 hours)

■ Chicken Breasts (1.50 kg)

■ Minced Beef (1.50 kg)

■ Steak (1.50 kg)

15 Minutes

■ 1 Beverage Can (355 ml)

■ 2 Small Juice Boxes

(175–240 ml each)

30 Minutes

■ 2 to 6 Beverage Cans (355 ml each)

■ 2 Plastic 590 ml Bottles of Beverage

■ 4 to 6 Small Juice Boxes

(175–240 ml each)

■ 3 Foil Juice Packets

■ Wine (750 ml bottle)

45 Minutes

■ 2 Liter of Beverage

■ 1.9 Liters of Juice

■ Gelatin–1 package

Citrus Setting (6°C)

■ Oranges, Lemons, Limes, Pineapple,

Cantaloupe

■ Beans, Cucumbers, Tomatoes, Peppers,

Aubergine, Squash

Produce Setting (1°C)

■ Strawberries, Raspberries, Kiwifruit,

Pears, Cherries, Blackberries, Grapes,
Plums, Nectarines, Apples

■ Asparagus, Broccoli, Corn, Mushrooms,

Spinach, Cauliflower, Kale, Green Onion,
Beetroot, Onions

Meat Setting (–1°C)

■ Raw Meat, Fish and Poultry

Some CustomCool models feature a beverage
center. It is designed to store beverages at colder
temperatures. Select this feature if you like to
keep extra-chilled refreshments on hand.

Access by: Home > Options > Refrigerator
Options > Beverage Center

Activate by: Pressing ON.
Deactivate by: Pressing OFF.

How to Use the Beverage Center (LCD models only)

To remove:

Remove dairy bin first. Holding

the bottom of the dairy bin, lift the front

straight up, then lift up and out.
Holding left and right side of beverage

center, lift straight up and out.

Leave adapter in place.

To replace:

Engage backside of beverage center in

molded supports on adapter. Then push
down on the sides of the beverage center.
The beverage center will lock into place.

Replace dairy bin.

How to Remove and Replace the Beverage Center (LCD models only)

Dairy Bin

Adapter

Beverage
Center

9

About the water filter.

Place the top of the cartridge up
inside the cartridge holder and
slowly turn it to the right.

Cartridge
Holder

About the refrigerator doors.

Refrigerator Doors

The refrigerator doors may feel different than
the ones you are used to. The special door
opening/closing feature makes sure the doors
close all the way and are securely sealed.

When opening and closing the door you will
notice a stop position. If the door is opened
past this stop point, the door will remain open
to allow you to load and unload food more easily.
When the door is only partially open, it will
automatically close.

The resistance you feel at the stop position will
be reduced as the door is loaded with food.

When the door is only partially
open it will automatically close.

Beyond this stop the door will
stay open.

Water Filter Cartridge

The water filter cartridge is located in the back upper
right corner of the refrigerator compartment.

When to Replace the Filter

LCD Models:

A pop-up screen will appear on the LCD screen
to remind you to replace the water filter. You can
check the status of the water filter manually.

Access By: Home > Options > Dispenser Options >
Reset Water Filter

Non-LCD Models/External Controls:

There is a replacement indicator light for the water
filter cartridge on the dispenser. This light will turn
orange to tell you that you need to replace
the filter soon.

The filter cartridge should be replaced when the
replacement indicator light turns red or if the flow
of water to the dispenser or icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old
one by slowly turning it to the left. Do not pull down on
the cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

There is an adapter attached to the top

of the new filter cartridge.

The adapter must be removed before installing

the cartridge. To remove the adapter, turn it to

the left about 1/4 turn.

Fill the replacement cartridge with water

from the tap to allow for better flow from

the dispenser immediately after installation.
Line up the arrow on the cartridge and

the cartridge holder. Place the top of the new

cartridge up inside the holder. Do not push
it up into the holder.

Slowly turn it to the right until the filter cartridge

stops. DO NOT OVERTIGHTEN. As you turn

the cartridge, it will automatically raise itself into
position. The cartridge will rotate about 1/2 turn.

Run water from the dispenser for 5 minutes

to clear the system and prevent sputtering.

LCD Models:

Press FILTER REPLACED button to confirm

replacement.

Non-LCD Models:
Press the SET FEATURES pad until REPLACE
WATER FILTER is lit. Press and hold the ON/OFF

pad for 3 seconds. WATER FILTER IS RESET will
show in the window.

NOTE: A newly installed water filter cartridge may
cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug when a
replacement filter cartridge is not available.
The dispenser and the icemaker will not operate
without the filter or filter bypass plug.

Replacement Filters:
To order additional filter cartridges, contact your

local distributor.

10

About the shelves and bins.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and freezer
tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up,
then lift up and out.

To replace or relocate: Engage the back side
of the bin in the molded supports of the door.
Then push down on the front of the bin.
Bin will lock in place.

Small Bins
To remove: Lift the front of the bin straight up

then out.
To replace: Position the bin above the

rectangular molded supports on the door.
Then slide the bin down onto the support
to lock it in place.

The snugger helps prevent tipping, spilling or
sliding of small items stored on the door shelf.
Place a finger on either side of the snugger
near the rear and move it back and forth
to fit your needs.

Not all features are on all models.

Refrigerator bin

Freezer tilt-out bin

Snugger

Bottle Retainer

The bottle retainers are adjustable and keep tall
items from tipping over.

To remove: Lift the front of the retainer straight
up, then lift it up.

To replace or relocate: Engage the back
of the bottle retainer in the molded supports
on the door. Then push down on the front
of the bottle retainer.

Bottle
retainer

Door Beverage Rack (on some models)

This rack holds up to 5 cans.
The rack hangs from the sides of the

dairy bin.

To remove:

Empty the wine/beverage rack.
Holding the bottom of the dairy bin,

lift the front straight up, then lift up
and out.

To detach the rack from the dairy bin,
pull the rack’s side wires out of the holes
on each side of the dairy bin.

To replace:

Reattach the rack to the sides of the bin.
Engage the back side of the bin in the

molded supports on the door. Then push
down on the front of the bin. The bin will
lock into place.

11

QuickSpace™Shelf

This shelf splits in half and slides under itself
for storage of tall items on the shelf below.

This shelf can be removed and replaced or
relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf can not be used
in the lowest position.

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach
items stored behind others. The special edges
are designed to help prevent spills from dripping
to lower shelves.

To remove:

Slide the shelf out until it reaches the stop,
then press down on the tab and slide the shelf
straight out.

To replace or relocate:

Line the shelf up with the supports and slide it
into place. The shelf can be repositioned when
the door is at 90° or more. To reposition the shelf,
slide the shelf past the stops and angle
downward. Slide shelf down to the desired

position, line up with the supports and slide
into place.

Make sure you push the shelves all the way
back in before you close the door.

Press tab and pull shelf
forward to remove

Removable Beverage Rack

The beverage rack is designed to hold
a bottle on its side. It can be attached
to any slide-out shelf.

To install:

Line up the large part of the slots on
the top of the rack with the tabs under
the shelf.

Then slide the rack back to lock it
in place.

1

2

About the shelves and bins.

12

Slide-Out Freezer Shelves

To remove, slide out to the stop position, lift the

front past the stop position and slide out.

Make sure you push the shelves all the way
back in before you close the door.

Deep Freezer Baskets

To remove, push the basket all the way to the

back of the freezer. Lift up until the back pins are
disengaged. Lift the entire basket up and pull out.

The divider can be used to organize food
packages. For large packages, simply fold
down the divider.

Make sure you push the baskets all the way
back in before you close the door.

WARNING: Poor performance may occur
if freezer baskets are not used. Storage of
items in the freezer without using baskets
may result in poor temperature performance
due to restrictions of air flow within the
freezer compartment.

Not all features are on all models.

Freezer Baskets

To remove, slide out to the stop position, lift the

front past the stop position and slide out.

Make sure you push the baskets all the way
back in before you close the door.

WARNING: Poor performance may occur
if freezer baskets are not used. Storage of
items in the freezer without using baskets
may result in poor temperature performance
due to restrictions of air flow within the
freezer compartment.

Divider

Fixed Freezer Shelves

There are two types of fixed freezer shelves.

To remove this type of shelf:

Lift the shelf up at the left side.
Bring the shelf out.

To remove this type of shelf:

Lift up the left side of the shelf and slide it
left into the center of the shelf supports.

Rotate the right side of the shelf up and
out of the shelf supports.

13

Loading the Freezer Compartment

Load so that at least 15 mm of space remains
clear between stacks of packages and 15 mm
to 25 mm of space between the top of any
stack and any shelf or basket above it.
Packages may hang over the front of shelves
but must remain 15 mm from doors.

■ Food to be frozen must not be placed

in direct contact with food in storage.
If food is to be frozen every day, it may
be necessary to reduce the quantity to
be frozen.

■ If a quantity of food needs to be frozen,

set the freezer control to its coldest setting.
After the food is frozen, reset the freezer
control to its initial position.

■ Food is most quickly frozen on the middle

three shelves of the freezer compartment
and most slowly in the freezer door shelves.

■ Do not store commercially quick-frozen

food longer than the time recommended
by the food manufacturers.

■ If the power to the appliance is shut off

for an extended time or if the refrigerating
system fails, do not open the doors unless
absolutely necessary. When it is necessary,
close them as quickly as possible so the
frozen food will stay frozen as long as
possible.

■ The freezer door storage shelves marked

with a two-star label are only appropriate
for the storage of previously frozen food.

Effervescent drinks should not be stored
in the freezer compartment.

Freezer Performance

This Refrigerator/Freezer has an overall “Four Star” rating.
Freezer performance is classified by star ratings defined by ISO 15502 STANDARD AND

SUMMARY BELOW:

CODE

or

FREEZING–LOAD TEMP.
(FOOD TEMPERATURE)

Below –6°C.
Below –12°C.
Below –18°C.

About the freezer compartment.

14

About crisper removal.

Not all features are on all models.

About the crispers and pans.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom
of the drawers should be wiped dry.

On some models the bottom drawer has
a cover that slides back as the drawer is opened.
This allows full access to the drawer. As the
drawer is closed, the cover will slide forward
into its original position.

Adjustable Humidity Crispers

Slide the control all the way to the
(high) setting to provide high humidity
recommended for most vegetables.

Slide the control all the way to the (low)
setting to provide lower humidity levels
recommended for most fruits.

Convertible Meat Pan

The convertible meat pan has its own cold air
duct to allow a stream of cold air from the freezer
compartment to flow to the pan.

The variable temperature control regulates
the air flow from the Climate Keeper.

™

Set the control to the (coldest) setting
to store fresh meats.

Set the control to (cold) to convert
the pan to normal refrigerator temperature
and provide extra vegetable storage space.
The cold air duct is turned off. Variable settings
between these extremes can be selected.

Crisper Removal

The top crispers can easily be removed by pulling
the drawer straight out and lifting the drawer
up and over the stop location.

If the door prevents you from taking out the
drawers, first try to remove the door bins.
If this does not offer enough clearance, the
refrigerator will need to be rolled forward until
the door opens enough to slide the drawers out.
In some cases, when you roll the refrigerator out,
you will need to move the refrigerator to the left
or right as you roll it out.

To remove the bottom crisper:

Pull the drawer out to the stop position.
Rotate all four swing locks to the unlock

position.
Lift the front of the drawer up and out.

To replace the bottom crisper:

Make sure all four swing locks are
in the unlock position.

Place the sides of the drawer into the drawer
supports, making sure the swing locks fit
on the drawer slots.

Lock all four swing locks by rotating them
to the lock position.

A newly-installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker

The icemaker will produce seven cubes
per cycle–approximately 100–130 cubes
in a 24-hour period, depending on freezer
compartment temperature, room temperature,
number of door openings and other use
conditions.

To access the icemaker: Pull the shelf above
the ice drawer straight out. Always be sure
to replace the shelf.

If the refrigerator is operated before the water
connection is made to the icemaker, set the
power switch in the O position.

When the refrigerator has been connected
to the water supply, set the power switch
to the l position.

You will hear a buzzing sound each time
the icemaker fills with water.

The icemaker will fill with water when it cools
to – 10°C. A newly-installed refrigerator may take
12 to 24 hours to begin making ice cubes.

Throw away the first few batches of ice to allow
the water line to clear.

Be sure nothing interferes with the sweep
of the feeler arm.

When the bin fills to the level of the feeler arm,
the icemaker will stop producing ice. It is normal
for several cubes to be joined together. If ice is
not used frequently, old ice cubes will become
cloudy, taste stale and shrink.

If ice cubes get stuck in the icemaker, the green
power light will blink. To correct this, set the
power switch to O and remove the cubes.
Set the power switch to I to restart the icemaker.
After the icemaker has been turned on again,
there will be a delay of about 45 minutes before
the icemaker resumes operation.

NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle
multiple times when making one batch of ice.

WARNING:Connect to potable

water supply only. Installation of the icemaker
must be done by a qualified service technician.

Special note about ClimateKeeper2™dispenser
models:

■ Dispenser models have a tilt-out ice bin.

The bin can be tilted out as shown in
the illustrations, and it will hold itself up while
you take ice out or turn the icemaker power
switch on and off. Be sure to put the bin back
in place before closing the door.

■ To restore your ice level from an empty bucket

stage, the following steps are recommended:

12 hours after the first batch of ice has fallen
into the bin, dispense 3 to 4 cubes.

After an additional 6 hours, dispense 3 to 4
cubes again.

These steps will restore your ice level
in the shortest amount of time.

Pull the upper freezer shelf straight
out to access the icemaker. Always
be sure to replace the shelf. The
shelf can be used for storage.

NOTE: In 25BIS Models, the ice bin
is suitable for the storage of ice
only.

Icemaker

Feeler Arm

Power
Switch

Green
Power Light

Ice Drawer

Shelf

Lift the bin, then pull it forward until the bin stops.

Lower the bin to access ice or reach the power
switch.

NOTE: In order to take full advantage of the tilt-out ice bin,
only store items on the shelf below the ice bin that are no
taller than the lowest point on the bin.

On dispenser models with a tilt-out ice bin, to
access ice or reach the power switch:

Ice Storage Drawer

To access ice, pull the drawer forward.
To remove:

Set the icemaker power switch to the O (off)
position. Pull the drawer straight out and
then lift past the stop position.

To replace:

When replacing the drawer, be sure to press
it firmly into place. If it does not go all the way
back, remove it and rotate the drive mechanism
1/4 turn. Then push the drawer back again.

Ice Drawer

About the automatic icemaker.

Rotate

Drive
Mechanism

15

16

About the ice and water dispenser. (on some models)

Spill Shelf

To Use the Dispenser

Select CUBED, CRUSHED or WATER .
Press the glass gently against the top

of the dispenser cradle.
The spill shelf is not self-draining. To reduce water

spotting, the shelf and its grille should be cleaned
regularly.

If no water is dispensed when the refrigerator is first
installed, there may be air in the water line system.
Press the dispenser arm for at least two minutes to
remove trapped air from the water line and to fill the
water system. To flush out impurities in the water line,
throw away the first six glassfuls of water.

CAUTION: Never put fingers or any other objects into
the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK or

LOCK

CONTROLS

pad for 3 seconds
to lock the dispenser and control
panel. To unlock, press and hold
the pad again for 3 seconds.

Dispenser Light

The LIGHT pad turns the night
light in the dispenser on and off.

The light also comes on when the
dispenser cradle is pressed. On
some models, if this light burns
out, it should be replaced with a
6 watt 12V maximum bulb.

Door Alarm

Use Door Alarm to sound if
either door is open for more
than 3 minutes. The alarm will
stop once the door is closed.
For LCD models, a popup screen
will appear. The alarm can be
silenced by touching the LCD
screen.

LCD Models:
Access By: Home > Options > Information and Settings

> Settings > Door Alarm

Access By: Pressing ON.
Deactivate By: Pressing OFF.

Non-LCD Models:

Press the SET FEATURES pad once and DOOR ALARM
will blink. Press ON/OFF and the door alarm will be set
and the icon will turn solid. Press ON/OFF again to turn
the alarm off.

Quick Ice

When you need to speed up ice
production, use the Quick Ice
feature. While this feature is
turned on, the freezer fan runs
continuously for 48 hours, or until
the feature is turned OFF. During
this period, ice production will
increase up to 40%. Models with

the integrated ice feature system require at FIRST USE
at least half an 8 oz. glass of ice to be dispensed every
6 to 12 hours. This will help the icemaker fill the bucket
properly so that dispensing is better.

How to Use
LCD Models:
Access by: Home > Options > Freezer Options >

Quick Ice

Activate by: Pressing ON.
Deactivate by: Pressing OFF.

Non-LCD Models:

Press the SET FEATURES pad twice and QUICK ICE will
blink. Press ON/OFF to turn the feature on, then again
to turn it off.

Precise Fill (on some models)

This water dispenser is equipped with a feature called
“precise fill.” This feature allows you to choose a precise
amount of water (cups or ounces) that you would like
dispensed. Pints and Liters are also available for LCD
models.

LCD Models
Access By: Home > Options > Dispenser Options >

Precise Fill > Set Amount
Activate By: Using the arrow buttons to select

the desired amount. Press MORE UNITS to select
between CUPS, OUNCES, PINTS or LITERS.

Non-LCD Models

Press the PRECISE FILL CUPS/OZ pad. The WATER
pad will light and the CRUSHED and CUBED ice
pads will turn off. The last unit used will be
displayed.

Press the PRECISE FILL pad again to toggle
between cups and ounces.

If you selected OUNCES, press the or pad to
select the number of ounces you would like to have
dispensed between 2–99 ounces. The default is
8 ounces.

If you selected CUPS, press the or pad to select
the amount you would like to have dispensed. They
are displayed as 0.25, 0.33, 0.5, 0.66 and 0.75, with the
highest amount being 9.75 cups. The default is 1 cup.
For liters, the amounts are displayed as 0.05 to 2.25
in increments of 0.05.

Press the cup against the cradle and water will
begin dispensing. It will automatically stop when
the amount set has been dispensed. The display
will show the amount of water dispensed, beep,
then reset after 5 seconds.

NOTE: Do not leave the dispenser unattended when
water is being dispensed.

If you would like to stop dispensing water
before the specified amount has been dispensed,
just remove the cup from the cradle. The display
will show the amount that has been dispensed
for 5 seconds. If the cup switch is pressed again
within that time, the dispenser will continue up
to the set amount. If not, the display will return

to the set amount.

>

>

>

>

Cleaning the Outside

The dispenser drip area, beneath the grille, should be

wiped dry. Water left in this area may leave deposits.
Remove the deposits by adding undiluted vinegar to
the well. Soak until the deposits disappear or become
loose enough to rinse away.

The dispenser cradle. Before cleaning, lock the
dispenser by pressing and holding the LOCK or LOCK
CONTROLS pad for 3 seconds. Clean with warm water
and baking soda solution—about a tablespoon (15 ml)
of baking soda to a quart (1 liter) of water. Rinse
thoroughly and wipe dry.

The door handles and trim. Clean with a cloth
dampened with soapy water. Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a commercially
available stainless steel cleaner. A spray-on stainless
steel cleaner works best.

Do not use appliance wax or polish on the stainless
steel.

Keep the outside clean. Wipe with a clean cloth lightly
dampened with kitchen appliance wax or mild liquid
dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring pads,
powdered cleaners, bleach or cleaners containing
bleach because these products can scratch and
weaken the paint finish.

Dispenser drip area.

Care and cleaning of the refrigerator.

Important Facts About Your Dispenser

■ Do not add ice from trays or bags to the storage

drawer. It may not crush or dispense well.

■ Avoid overfilling glass with ice and use of narrow

glasses. Backed-up ice can jam the chute or
cause the door in the chute to freeze shut.
If ice is blocking the chute, poke it through
with a wooden spoon.

■ Beverages and foods should not be quick-chilled

in the ice storage drawer. Cans, bottles or food
packages in the storage drawer may cause
the icemaker or auger to jam.

■ To keep dispensed ice from missing the glass,

put the glass close to, but not touching,
the dispenser opening.

■ Some crushed ice may be dispensed even

though you selected CUBED. This happens
occasionally when a few cubes accidentally
get directed to the crusher.

■ After crushed ice is dispensed, some water may

drip from the chute.

■ Sometimes a small mound of snow will form on

the door in the ice chute. This condition is normal
and usually occurs when you have dispensed
crushed ice repeatedly. The snow will eventually
evaporate.

17

18

For long vacations or absences, remove food
and unplug the refrigerator. Clean the interior
with a baking soda solution of 15 ml of baking
soda to 1 liter of water. Leave the doors open.

Set the icemaker power switch to the O position
and shut off the water supply to the refrigerator.

If the temperature can drop below freezing,
have a qualified servicer drain the water supply
system to prevent serious property damage
due to flooding.

Care and cleaning of the refrigerator.

Behind the Refrigerator

Be careful when moving the refrigerator away
from the wall. All types of floor coverings can be
damaged, particularly cushioned coverings and
those with embossed surfaces.

Pull the refrigerator straight out and return
it to position by pushing it straight in. Moving
the refrigerator in a side direction may result
in damage to the floor covering or refrigerator.

When pushing the refrigerator back, make sure
you don’t roll over the power cord or icemaker
supply line.

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and
drawers by taping them securely in place
to prevent damage.

When using a hand truck to move
the refrigerator, do not rest the front or back
of the refrigerator against the hand truck.
This could damage the refrigerator. Handle
only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright
position during moving.

Cleaning the Inside

To help prevent odors, leave an open box

of baking soda in the fresh food and freezer
compartments.

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out
of sponge or cloth when cleaning around
switches, lights or controls.

Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) of water. This both cleans
and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that
which is recommended, especially those that
contain petroleum distillates, can crack or
damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot
water because the extreme temperature
difference may cause them to break. Handle
glass shelves carefully. Bumping tempered
glass can cause it to shatter.

Do not wash any plastic refrigerator parts
in the dishwasher.

The chill/thaw tray is dishwasher safe.

Replacing the light bulbs.

Setting the controls to 0 (off) does not remove power to the light circuit.

19

Refrigerator Compartment—Lower Light

This light is located above the top drawer.

Unplug the refrigerator.
Remove the convertible meat drawer control

knob by pulling straight out.
Lift the light shield up and pull it out.

After replacing the bulb with an appliance
bulb of the same or lower wattage, replace
the shield and the knob.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.
Remove the shelf just above the light shield.

(The shelf will be easier to remove if it is
emptied first.) On some models, a screw
at the top of the light shield will need to
be removed.

To remove the light shield, press in
on the sides, and lift up and out.

Replace the bulb with an appliance bulb
of the same or lower wattage, and reinstall
the light shield. When reinstalling the light
shield, make sure the top tabs snap
securely into place. Replace the screw
(on some models).

Reinstall the shelf and plug the refrigerator
back in.

Dispenser

Unplug the refrigerator.
The bulb is located on the dispenser under

the control panel. Remove the light bulb
by turning it counterclockwise.

Replace the bulb with a bulb of the same
size and wattage.

Plug the refrigerator back in.

Refrigerator Compartment—Upper Light

Unplug the refrigerator.
The bulbs are located at the top of

the compartment, inside the light shield.
On some models, a screw at the front of
the light shield will have to be removed.
On other models, the screw is located in the
pocket located at the back of the light shield.

To remove the light shield, on some models,
press in on the tabs on the sides of the shield
and slide forward and out. On other models,
just slide the shield forward and out.

After replacing the bulb with an appliance
bulb of the same or lower wattage, replace
the light shield and screws (on some models).
When replacing the light shield, make sure
that the tabs at the back of the shield fit
into the slots at the back of the light shield
housing.

Plug the refrigerator back in.

Tabs

Pocket

OR

Your light shield will look like
one of the following:

C

O

L

D

D

L

E

O

S

C

T

20

Trim kits and decorator panels.

Read these instructions completely and carefully.

Before You Begin

Some models are equipped with trim kits that allow you to install door panels.

Panels less than 6 mm thick

When installing wood panels less than 6 mm thick, you need to create a filler panel, such as 3 mm cardboard, that
will fit between the face of the door and the wood panel. If you are installing the pre-cut decorator panels, pre-cut
filler panels are included in the kit. The combined thickness of the decorator or wood panel and the filler panel should
be 6 mm.

For Built-In Style models

19 mm or Raised Panel

A raised panel design screwed or glued to a 6 mm thick backing, or a 19 mm routed board can be used.
The raised portion of the panel must be fabricated to permit clearances of at least 5.1 cm from the handle
side for fingertip clearance.

Panels thicker than 6mm, up to 19 mm max, will require that the outer 8 mm of panel perimeter be no thicker
than 6 mm.

Weight limitations for custom panels:
Refrigerator Door 17 kg max.
Freezer Door 13 kg max.

5.1 cm
Clearance
Handle Side

Appearance
Panel

Refrigerator
Door

6 mm Thick
Backing

19 mm

Panels 6 mm thick or less

Panels thicker than 6 mm

6 mm max

6 mm max

19 mm

8 mm

21

Freezer Panel
Without Dispenser

Freezer Panel
With Dispenser

Refrigerator Panel

Dimensions for Custom Wood Panels

Cut
out

8 mm

36.8 cm

170.9 cm

3 mm

FRONT

8 mm

45.4 cm

36.8 cm

85.4 cm

3 mm

Cut
out

FRONT

8 mm

170.9 cm

3 mm

Cut
out

49.5 cm

FRONT

The areas at the top of the panels need to be cut out of the panels.

22

Inserting the door panels.

Read these instructions completely and carefully.

Attach the Top Trim on the Freezer and Refrigerator Doors.

The Top Trim can be found inside the refrigerator
compartment.

With a T-20 Torxdriver, attach the Top Trim, using
two screws on each Top Trim piece, to the top

of each door. Hand tighten only. Make sure that the top
of each panel fits snugly behind the lip of the Top Trim.

Insert the Freezer Panel and Refrigerator Panel.

Carefully push the freezer panel in until it slides into the
slot behind the door handle. Push the filler panel (required
with some door panels) in behind the decorator panel.
Repeat for refrigerator panel.

If your model has a dispenser, this step only applies
to the refrigerator panel and top freezer panel.

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides into the slot
behind the door handle. Push the filler panel (required
with some door panels) in behind the decorator panel.

Cut-Out

Cut-Out

Top Trim Screws

Top
Freezer
Panel

Bottom
Freezer
Panel

Side Trim

Side Trim

Refrigerator
Panel

Top Trim Screws

23

Install the Side Trim.

These pieces are tucked inside the refrigerator
door handle.

Do not remove the protective film on the outside
of the Side Trim until the Side Trim is installed.

Fit the bottom of the Side Trim under the Bottom Trim
as illustrated.

Hold the Side Trim against the front face of the decorator
panels and fit the Side Trim under the Top Trim. Make
sure the Side Trim is fitted correctly and that you
are satisfied with the appearance of all the parts.

Side
Tri m

Side
Tri m

Bottom Trim

Top Trim

Removing and replacing the doors.

When installing or moving the refrigerator, the doors may need to be removed in order to fit the refrigerator through
a doorway.

Removing the Doors

Make sure the doors are closed and the refrigerator
is unplugged.

Disconnect water line and wiring harness.

Near the lower hinge on the freezer side, push in on
the collars at each end of the coupling, and pull the water
line tubing from the coupling. Also, disconnect wiring
harness. Pull the water line and the harness through
the lower rail.

Remove the hinge covers and the hinges.

In order to access the hinges, the hinge covers need to
be removed. Remove the cover by grasping it on the sides,
near the back of the cover. Push back on the cover and
lift up at the back, then the front.

NOTE: DO NOT use a screwdriver to remove the cover. BE
CAREFUL not to break the rear retaining tab on the hinge
cover. Remove the hinges using a Torx T-20.

Remove the doors.

Carefully rotate the door to 90°. Guiding the disconnected
water line and wiring harness, lift the door straight up.

NOTE: Not lifting the door straight up may damage
the bottom hinge. Place doors on a protected surface.

NOTE: Be careful not to pinch the water tubing and the wire
harness at the bottom of the door.

NOTE: Do not allow the connector to contact the floor.
Hard contact can damage the connector. See “Replacing
the Doors.”

Replacing the Doors

Place doors on bottom hinges.

With the door at 90°, lower the door straight down onto
the bottom hinge. Carefully close the door.

NOTE: Not lowering the door straight down onto the bottom
hinge may damage the hinge.

NOTE: Do not allow the connector to contact the floor.
Hard contact can damage the connector.

Replace top hinges and hinge covers.

Reinstall the top hinges using a Torx T-20. Replace the hinge
covers. If the doors are not level, adjust the bottom right
hinge with a 7/16″ open ended wrench.

Reconnect water line and wiring harness.

Insert water tubing back into coupling, making sure the
tubing is pushed far enough into the coupling so that you
no longer see the mark on the tubing. Reconnect the wiring
harness.

Turn on the water supply and plug the refrigerator back in.

90

Hinge Cover

Door

Hinge Pin

Wire Harness

Collars

Connector

24

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions

for local inspector’s use.

•

IMPORTANT – Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Do not install the refrigerator where the temperature
will go below 16°C because it will not run often enough
to maintain proper temperatures.

• Do not install the refrigerator where the temperature
will go above 37°C because it will not perform properly.

• Install it on a floor strong enough to support it fully
loaded.

REFRIGERATOR LOCATION

Installation

Refrigerator

Instructions

Models 21, 23, 25, 27 & 29

Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections:

CLEARANCES

If the refrigerator has an icemaker, it will have
to be connected to a cold water line. An approved
water supply kit is available at extra cost from your
local distributor.

Maximum permissible inlet water pressure–8.2 bars.
Minimum permissible inlet water pressure–2.8 bars.

Installation of the icemaker must be done by a qualified
service technician.

WATER SUPPLY TO THE ICEMAKER

(ON SOME MODELS)

21′ and 23′ 25′, 27′ and 29′

• Sides 4 mm 4 mm

• Top 25 mm 25 mm

• Back 13 mm 25 mm

25

29 27 25 23 21

A* 1733 mm 1733 mm 1733 mm 1733 mm 1733 mm

B 908 mm 908 mm 908 mm 908 mm 908 mm

C** 912 mm 879 mm 879 mm 738 mm 738 mm

D 1261 mm 1271 mm 1271 mm 1156 mm 1156 mm

E 1273 mm 1255 mm 1247 mm 1232 mm 1214 mm

F 1051 mm 1093 mm 1099 mm 989 mm 986 mm

G 1386 mm 1381 mm 1381 mm 1361 mm 1355 mm

H 1140 mm 1150 mm 1149 mm 1023 mm 994 mm

*Height does not include hinge.
**Depth includes handle.

DIMENSIONS

A

B

C

D

F

E

H

G

26

Installation Instructions

The rollers have 3 purposes:

■

Rollers adjust so the door closes easily when opened
about halfway. [Raise the front about 5/8″ (16 mm)
from the floor.]

■

Rollers adjust so the refrigerator is firmly positioned
on the floor and does not wobble.

■

Rollers allow you to move the refrigerator away from
the wall for cleaning.

Final leveling adjustments should be made after
the refrigerator has been installed.

To adjust the rollers on 25′, 27′ and 29′ models:

■

Turn the roller
adjusting screws

clockwise to raise

the refrigerator,

counterclockwise to
lower it. Use a 3/8″

hex socket or wrench,
or an adjustable
wrench.

To adjust the rollers on 21′ and 23′ models:

Remove the base grille by opening the doors, removing
the screws at each end, and pulling it straight out.

Turn the front roller
adjusting screws

clockwise to raise

the refrigerator,

counterclockwise to
lower it. Use a 3/8″

hex socket or wrench,
or an adjustable
wrench.

These models also have rear adjustable rollers so you
can align the refrigerator with your kitchen cabinets.
Use a long-handled 5/16″ socket wrench to turn the
screws for the rear rollers–clockwise to raise the
refrigerator, counterclockwise to lower it.

Replace the base grille.

ROLLERS

Roller adjusting screw

Roller adjusting screws

After leveling, make sure that the refrigerator door is 1/16″
higher than the freezer door.

To align the doors, adjust the refrigerator door.

Using a 7/16″ socket wrench, turn the door adjusting
screw to the right to raise the door, to the left to lower
it. (A nylon plug, imbedded in the threads of the pin,
prevents the pin from turning unless a wrench is used.)

After one or two turns of the wrench, open and close
the refrigerator door and check the alignment at
the top of the doors.

To remove the base grille,
open the doors, remove
the screw at each end of
the base grille and then
pull the grille straight out.

7/16″ Socket Wrench

Raise

DOOR ALIGNMENT

Refrigerator door
needs to be raised.

Installation Instructions

27

DIMENSIONS AND SPECIFICATIONS

(for Built-In Style models)

178.4 cm

91.4 cm

61 cm

61 cm
Cabinet

Water Electrical

19 mm Airspace
13 mm Gap + 6 mm
(Wall Plates)

63.5 cm
Countertop

Installation Instructions

28

The water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
recommendations carefully to minimize the risk of
expensive water damage.

Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing
the water supply line to the refrigerator.

To prevent burns and product damage, do not hook
up the water line to the hot water line.

If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the O (off) position.

Do not install the icemaker tubing in areas where
temperatures fall below freezing.

When using any electrical device (such as a power drill)
during installation, be sure the device is insulated or
wired in a manner to prevent the hazard of electric
shock.

All installations must be in accordance with local
plumbing code requirements.

Installation of the icemaker must be done by
a qualified service technician.

WARNING! Connect to potable water

supply only.

BEFORE YOU BEGIN

INSTALLING THE WATER LINE

Place the compression nut and ferrule (sleeve) onto
the end of the tubing as shown.

Insert the end of the tubing into the water valve
connection as far as possible. While holding the tubing,
tighten the fitting.

Fasten the tubing into the clamp provided to hold it in
a vertical position. You may need to pry open the clamp.

On models using the
refrigeration connection
at the water valve, remove
the plastic flexible cap.

CONNECT THE TUBING TO THE
REFRIGERATOR

(CONT.)

1

Some models have the refrigerator connection at the end
of tubing located outside the compressor compartment
access cover. On other models, the compressor
compartment access cover must be removed in order
to access the refrigerator connection at the water valve.

Reattach the access cover.

NOTES:

• Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.

• We recommend installing a water filter if your
water supply has sand or particles that could clog
the screen of the refrigerator’s water valve. Install
it in the water line near the refrigerator.

CONNECT THE TUBING TO THE
REFRIGERATOR

1

Typical
Compression
Nut

Tubing
Clamp

Tubing

Ferrule
(sleeve)

Refrigerator
Connection

Tubing

Tubing Clamp

Typical
Compression Nut

Ferrule
(sleeve)

Refrigerator Connection

One of the illustrations below will look like
the connection on your icemaker.

Installation Instructions

29

Set the icemaker power switch to the l position. The
icemaker will not begin to operate until it reaches its
operating temperature of –9°C or below. It will then
begin operation automatically if the icemaker power
switch is in the l position.

NOTE: In lower water pressure conditions, the water
valve may turn on up to 3 times to deliver enough
water to the icemaker.

START THE ICEMAKER

3

Power
switch

Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.

TURN THE WATER ON AND PLUG IN
THE REFRIGERATOR

2

Normal operating sounds.

Newer refrigerators sound different from older refrigerators.
Modern refrigerators have more features and use newer
technology.

HUMMM...

WHOOSH...

■

The new high efficiency compressor may run faster
and longer than your old refrigerator and you may
hear a high-pitched hum or pulsating sound while
it is operating.

■

Sometimes the refrigerator runs for an extended period,
especially when the doors are opened frequently. This
means that the Frost Guard™feature is working to
prevent freezer burn and improve food preservation.

■

You may hear a whooshing sound when the doors close.
This is due to pressure equalizing within the refrigerator.

■

You may hear the fans spinning at high speeds.
This happens when the refrigerator is first plugged
in, when the doors are opened frequently or when
a large amount of food is added to the refrigerator
or freezer compartments. The fans are helping to
maintain the correct temperatures.

■

If either door is open for over 3 minutes, you may hear
the fans come on in order to cool the light bulbs.

■

The fans change speeds in order to provide optimal
cooling and energy savings.

■

You may hear the fan running after selecting one
of the CustomCool

™

settings.

CLICKS, POPS,

CRACKS and CHIRPS

■

You may hear cracking or popping sounds when
the refrigerator is first plugged in. This happens as
the refrigerator cools to the correct temperature.

■

Electronic dampers click open and closed to provide
optimal cooling and energy savings.

■

The compressor may cause a clicking or chirping
sound when attempting to restart (this could take
up to 5 minutes).

■

The electronic control board may cause a clicking
sound when relays activate to control refrigerator
components.

■

Expansion and contraction of cooling coils during and
after defrost can cause a cracking or popping sound.

■

On models with an icemaker, after an icemaking
cycle, you may hear the ice cubes dropping into
the ice bucket.

WATER SOUNDS

■

The flow of refrigerant through the freezer cooling coils
may make a gurgling noise like boiling water.

■

Water dropping on the defrost heater can cause
a sizzling, popping or buzzing sound during the
defrost cycle.

■

A water dripping noise may occur during the defrost
cycle as ice melts from the evaporator and flows into
the drain pan.

■

Closing the door may cause a gurgling sound due to
pressure equalization.

Do you hear what I hear? These sounds are normal.

For additional information on normal icemaker
and dispenser operating sounds, see the

About the automatic icemaker and About
the ice and water dispenser sections.

30