GE RAK3202 Installation manual
POWER CONNECTION CHART
GE 230/208 Volt Wall Plug Heater Wattage
Power Supply Kit Configuration Circuit Protective Device @ 230/208 Volts
RAK3152 Tandem 15-Amp Time-Delay Fuse or Breaker 2.55/2.09 KW
RAK3202 Perpendicular 20-Amp Time-Delay Fuse or Breaker 3.45/2.82 KW
RAK3302 Large Tandem 30-Amp Time-Delay Fuse or Breaker 5.00/4.10 KW
230/208 VOLT ELECTRICAL SUPPLY
A power supply kit must be used to supply power to the
Zoneline unit. The appropriate kit is determined by the
voltage, the means of electrical connection, and the
amperage of the branch circuit. See the POWER
CONNECTION CHART to confirm the appropriate kit.
All wiring, including installation of the receptacle,
must be in accordance with the NEC and local codes,
ordinances, and regulations.
Installation instructions
RAK3152, RAK3202,
for your new
RAK3302
Power Supply Kit for Cord
or Direct Connection
Before you begin – Read these instructions completely and carefully.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
TOOLS NEEDED
• 1/4″ Nut driver • Phillips screwdriver
• Wire cutter (For direct connect applications only.)
• This kit is for use with 230/208 volt 5200, 5500, and
7500 Series GE Zoneline units only.
IMPORTANT NOTES
• This unit must be properly grounded.
• The electrical rating marked on the previously installed
Zoneline and power supply kit must be the same as
the supply branch circuit.
• Aluminum building wiring may present special
problems—consult a qualified electrician.
• All wiring, including installation of the receptacle,
must be in accordance with the NEC and local codes,
ordinances, and regulations.
• Use ONLY the wiring size recommended for single
outlet branch circuit.
• Proper current protection is the responsibility of
the owner.
Tandem
15 Amp
230/208 volt receptacle configuration
Perpendicular
20 Amp
Large Tandem
30 Amp
Power supply kit
Recommended branch circuit wire sizes*
Nameplate
maximum circuit AWG wire
breaker size size**
15A 14
20A 12
30A 10
AWG – American Wire Gauge
* Single circuit breaker from main box
** Based on copper wire, single-insulated conductor at 60°C
NOTE: Use copper conductors only.
CAUTION:
Disconnect the electrical power
supply before wiring connections.
FOR 5200 AND 5500 SERIES MODELS ONLY
1. Remove the room cabinet by pulling it out at the bottom
to release it (1); then lift it up to clear the rail along the
unit top (2).
2. Insert the plug into the socket located in the wiring
compartment, making sure the plug is firmly seated
and the latches secure the connector assembly.
3. Position the cord and install the strain relief and screw
as shown.
4. Reinstall the room cabinet front by positioning on the
top brackets and securing the sides to the unit.
5. Install the attachment plug cap into the wall
receptacle and check the Zoneline operation.
2
FOR 230/208 VOLT POWER CORD CONNECTIONS ONLY
FOR 7500 SERIES MODELS ONLY
1. Remove the front panel by removing the filter, taking
out the four front screws, the upper two screws from
the top of the panel, and the shipping screws on each
side, if present. (Discard the two side shipping screws,
if present.)
2. Remove the junction box cover and the junction box
and discard.
3. Connect the power cord, with a loop, through the
strain relief.
4. Replace the case front panel by replacing the four
front screws and the two top screws. Replace the
filter.
Strain relief
IMPORTANT:
Power cord
must have a
loop.
Remove
junction
box and
cover
Side
shipping
screw
Side
shipping
screw
Screw
Plug into
building
receptacle
Yellow plug
to chassis
connector
Strain
relief
Cord
Loading...