GE QUNA Roadway Series Installation, Use And Maintenance Manual

GE Lighting

QUNA Roadway Series

Installation, Use and Maintenance Manual

READ THROUGHLY BEFORE INSTALLATION

SAVE THESE INSTRUCTIONS FOR FUTURE USE

These Instructions do not purport to cover all details or
variations in luminaire nor to provide for every possible
contingency to be met in connection with installation, operation
or maintenance. Should further information be desired or should
particular problem arise which are not covered sufficiently for
the purchaser’s purpose, the matter should be referred to
General Electric Company.

I. GENERAL

This luminaire is designed for outdoor lighting application, and
should not be used in areas of limited ventilations, or in high
ambient temperature enclosures. Best results will be obtained if
installed and maintained according to the following
recommendations. Please refer section III for the application
limitation details.

The Manufacturer has made every effort during the design and
construction stages to make its products completely free of risks
when correctly used. Note however that accident prevention
and safety regulations stipulate that the users of the product is
obliged to ensure that all persons involved in servicing, installing,
handling, using or selling the products are familiar with the
information supplied by the Manufacturer and fully aware of
any precautions that must be adopted. Depending on the
circumstances, the instructions in this document must be
communicated, together with any other information that may
be necessary, to any Company or person involved in the
installation of GE lighting products.

II. UNPACKING

The luminaire has been properly packed to avoid damage
during transit. Inspect the luminaries to confirm there is no
damage. Do not install a damaged luminaire or damaged
luminaire components.

The carton consists of:

• Fixture

• Instruction Manual

(Figure 1)

Class I IP44 (Optical Housing IP66) 220V/50Hz

WARNING

CAUTION FOR ELECTRIC SHOCK/RISK OF BURN/PROPER
INSTALLATION

 Non-professionals are not allowed to operate. Shut off

the power before maintenance.

 Risk of burn, allow lamps/fixture to cool down before

handling.

III. APPLICATION NOTICE

PLEASE APPLY THE PRODUCT ACCORDING TO FOLLOWING
STATEMENT

QUNA is a roadway luminaire used for Major/Collector roadway,
Highway, Commercial plaza, Industrial park, Residential area and
Parking lots, etc. It can’t be installed in places with obvious
vibration, like bridge/overpass, etc.
It can be installed between 6m and 9m. Expected outer diameter
of pole is 48-52mm.

IV. INSTALLATION

WARNING

1. Ensure this manual is provided to the installers and users.

2. Cut off the power before installation and maintenance.

3. Luminaire may fall down if not installed properly. Please follow the

instruction.

4. Lu minai re may fall down if the safety chain is not installed properly.

Please follow the instruction.

5. Never touch the lamps while they are working.

6. Replace the screen immediately if damaged or broken.

7. This fixture is only used for outdoor.

8. Not suitable for bridge and/or overpass application.

9. If installed in the places of high-salt environment (like coastal areas),

please contact the professionals of General Electric Company for
more information.

Document No.:ZQKG/JS16-Qun10-2010 GE No.: GE2015-0738 ECN: CR2016-5622 Revision:C

CAUTION

Risk of Injury

 Ware safety glasses and proper aid during installation and

maintenance

Notice:

TOOLS/ACCESSRIES YOU WILL NEED

Wire Stripper: Used for removal the insulation of wire lead.
Screwdriver – (3mm): used for connecting the power cord.
Screwdriver – (4mm): used for connecting safety chain.
Allen Key wrenches – (5mm) A/F: used for fixture and mounting

pole connection and adjustment.

P

PRE-INSTALLATION

1. Open the two latches of fixture, open the upper cover,

raise support (ensure it self-lock with hand help) and take
out the Accessory A of safety chain.

2. Loosen the screw of Accessory A to pull out the Safety

Chain.

(Figure 2)

I

INSTALL LUMINAIRE

1. Raise the fixture with the components of Accessory A

to planned installation pole.

2. Pull the Safety Chain through Pre-made Hole and the

two holes of Accessory A. Tighten the screw of
Accessory A. (Refer to the Figure 2)

3. Adjust the clamp plate to load the fixture to Pole (Keep

the upper cover of fixture open for observation to
ensure fixture fully loaded), tighten the three set
screws by turns.

4. Connect power supply leads: pull through leads from

the hole of cover, loosen screws of wiring clamp and
tighten them after pressing the leads, loosen the
screws on terminal block, connect leads properly in
accordance with Figure 3, tighten screws on terminal
block and wiring clamp. Connection is finished.

5. Install lamp:

Step 1 Disconnect the connector of lampholder wires.
Step 2 Open two latches of lampholder ’s cap and pull

out.

Step 3 Install the eligible recommended GE lamp

shown in PRODUCT BASIC INFO.

Step 4 Restore the lampholder cap.

1) Two men are required while installing.

2) Pre-made a hole of Ø4-6mm near the end of Pole for

Safety Chain.

3) Ensure Min. 25mm from the Accessory A while

locking Safety Chain. (Refer to the Figue 2)

4) Any situation, the torque of the three set screws

can’t too big to avoid mechanical damage.

5) Min. 3x1.0 mm

2

Power supply lead need be set in the

Pole.

(Figure 3)

V. MAINTENANCE/ LAMP REPLACEMENT

OPTICAL MAINTENANCE

In order to maintain high efficiency of reflectors and refractors,
a regular cleaning cycle should be established with frequency
dependent on local conditions. Use a mild soap or detergent
which is essentially neutral (pH approximately 6 to 8),
nonabrasive, and which contains no chlorinated or aromatic
hydrocarbons. Wash thoroughly, using a soft cloth, or brush if
necessary, Rinse in clean, cold water and wipe dry.

INSPECT AND REPLACE ANY DAMAGED REFRACTORS OR GASKET
IF APPLICABLE.

FAILURE PARTS NEED TO BE REPLACED IF YOU INSPECT THE
LAMP EXTINCT, FLICKING OR CYCLING. ORDER THE
REPLACEMENT PART INDIVIDUALLY. CONTACT THE
MANUFACTURES FOR THE MAINTENANCE SERVICE.

LAMP REPLACEMENT

Light output is also dependent on buring time of lamp. In
applications where light levels are critical, it may be desirable to
replace lamps before the end of life. Lamp manufacturer can
provide life curve date sheet of light output .

Step 1 Shut off power first.
Step 2 Open the two latches of fixture.
Step 3 Open the upper cover and raise support.
Step 4 Disconnect the connector of lampholder wires.
Step 5 Open two latches of lampholder’s cap and pull out .
Step 6 Remove the lamp that do not work properly.
Step 7 Reinstall the eligible recommended GE lamp shown in

PRODUCT BASIC INFO.

Step 8 Restore.

CAUTION: PLEASE NOTE THE LAMP TYPE, WATTAGE SHALL BE
SAME AS THE INDICATION OF PRODUCT LABEL.

If lamp is handled, fingerprint, grease or oils should be removed
from lamp with isopropyl alcohol. This will remove material
which will cause whitish spotting, and premature lamp failure.
Dry lamp carefully with cotton or clean cloth.

Accessory B: Fixed on lower

cover of fixture.

Pole

Safety Chain

Min. 25mm

Accessory A

Pre-made Hole

(Ø4-6mm)

Min. 3x1.0 mm2

Wire stripping 8~10mm

Neutral Wire-N

Earth Wire

Line Wire-L

Fuze Tube Slot

Document No.:ZQKG/JS16-Qun10-2010 GE No.: GE2015-0738 ECN: CR2016-5622 Revision:C