Installation
Instructions
Advantium® 120V Built-In SpeedCook and 120V Built-In Convection Ovens
CSB9120
PSB9120
ZSC1201
ZSC1202
CWB7030
PWB7030
CWB713
Español
For a Spanish version of this manual, visit our Website at GEAppliances.com.
Para consultar una version en español de este manual de instrucciones, visite nuestro
sitio de internet GEAppliances.com.
31-2000001-5
01-19 GEA |
GE is a trademark of the General Electric Company. Manufactured under trademark license. |
Safety Information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT — Save these instructions for local inspector’s use.
IMPORTANT — Observe all governing codes and ordinances.
•Note to Installer — Be sure to leave these instructions with the Consumer.
•Note to Consumer — Keep these instructions with your Owner’s Manual for future reference.
•Skill Level — Installation of this appliance requires basic mechanical and electrical skills.
•Completion Time — 1 Hour.
•Proper installation is the responsibility
of the installer. Product failure due to improper installation is not covered under the warranty. See Owner’s Manual for warranty information.
NOTE: This oven is only approved to be installed under the specific models as labeled on this unit.
IMPORTANT — Use this oven only for its intended purpose. Never use the oven for warming or heating a room. Prolonged use of the oven without proper ventilation can be hazardous.
CAUTION |
For personal safety, remove |
house fuse or oven circuit breaker before |
|
beginning installation to avoid severe or fatal |
|
shock injury. |
|
CAUTION |
For personal safety, the |
mounting surface must be capable of supporting the cabinet load, in addition to the added weight of the oven and drawer, plus additional oven
loads.
CAUTION If installing the Advantium/ Convection 120V Oven below 36Ǝ, you must use the plastic bottom trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot
surfaces.
CAUTION If installing the Advantium/ Convection 120V Oven below 36Ǝ, do not remove the plastic door trim due to burn risk to children. The plastic trim acts as insulation and will help prevent burns to children from hot surfaces.
CONTENTS |
|
Design Information |
|
Models Available ............................................... |
2 |
Product Dimensions and Clearances................ |
3 |
Tools Required.................................................. |
3 |
Parts Supplied................................................... |
3 |
Advance Planning ............................................. |
3 |
Installation Preparation |
|
Electrical Requirements .................................... |
4 |
Preparing the Opening (Standard)................. |
5-8 |
Preparing the Opening (Flush Mount).......... |
9-10 |
Storage Drawer Preparation |
|
Standard ......................................................... |
11 |
Flush ............................................................... |
11 |
Installation Instructions |
|
Step 1, Remove Packaging and Parts............ |
12 |
Step 2, Door Trim Removal for above 36” |
|
Installation only............................................... |
13 |
Step 3, Slide the Oven into the Cutout ........... |
13 |
Step 4, Install Bottom Trim.............................. |
14 |
Step 5, Install Bottom Trim with Accessory |
|
Drawer........................................................... |
14 |
Step 6, Install Mounting Screws...................... |
14 |
Step 7, Finalize Installation ............................. |
14 |
MODELS AVAILABLE |
|
Profile Models: |
|
PSB9120WW – White* |
|
PSB9120BB – Black |
|
PSB9120SS – Stainless Steel |
|
PSB9120ES – Slate |
|
PWB7030SL – Stainless Steel |
|
PWB7030EL – Slate |
|
PSB9120BL – Black Stainless Steel |
|
Monogram Models: |
|
ZSC1201SS – Stainless Steel |
|
ZSC1202SS – Stainless Steel** |
|
Café Model: |
|
CSB9120SS – Stainless Steel |
|
CWB7030SL – Stainless Steel |
|
*No color-matched drawer available for this model.
**This unit cannot be installed with an accessory storage drawer.
2
Design Information
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.
21-1/2Ǝ |
29-3/4Ǝ |
1-3/5Ǝ |
|
19Ǝ
1Ǝ |
|
1-1/10Ǝ |
13Ǝ |
TOOLS AND PARTS REQUIRED
(NOT SUPPLIED)
•#2 Phillips screwdriver
•Hand-held drill
•High speed drill bit, 3/32Ǝ diameter
•3/8Ǝ slot-head screwdriver
•Level
•Saw
•3/8Ǝ min. plywood for floor (if required)
•Wood screws or other hardware for installing runner or shelf to support oven (if required)
•Safety glasses or goggles
FLUSH MOUNT INSTALLATION (Monogram Only)
This installation method allows for the unit face to be inline with the cabinet face.
IMPORTANT: HIGH SKILL LEVEL IN CARPENTRY IS REQUIRED. Non-standard cabinetry may be required.
Flush installation of the oven will lead to the exposure of the cabinet face frame edges.
Side cleats may be visible and should be a finished surface.
ADVANCE PLANNING
• 7KHVH RYHQV PD\ EH LQVWDOOHG GLUHFWO\ LQWR D Ǝ wide oven cabinet with standard installation.
•Cutout height dimensions are different for installations with an accessory storage drawer. Make sure to use the correct cutout when preparing the opening.
•Allow for clearance to adjacent corners, walls, drawers, etc.
•Cabinets installed adjacent to wall ovens must have an adhesion spec of at least 194ºF temperature rating.
The oven must be securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.
If installing the drawer accessory, the drawer must be assembled to the oven prior to installation into the cabinet. See the Accessory Storage Drawer Assembly Instructions.
3
Installation Preparation
ELECTRICAL REQUIREMENTS
Single Advantium/Convection 120 Installation:
This product requires a 120-volt, 60 Hz, 15-amp circuit and draws 1.8 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency.
•Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating.
•The power supply cord and plug should be brought to a separate 15 or 20 ampere branch circuit single grounded receptacle. The outlet box should be located within reach of the 48” power cord.
ELECTRICAL LOCATION
6” |
9”
Locate outlet box in the shaded area
Install a recessed electrical outlet in the back wall of the opening within 6Ǝ of either side and at least 9Ǝ above the cutout floor.
GROUNDING
INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING Improper use of the grounding plug can result in a risk of electric shock.
IMPORTANT: (Please read carefully).
The power cord of this appliance is equipped with a three-prong (grounding) plug that mates with a standard three-prong grounding wall receptacle to minimize the possibility of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
• Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the consumer to have it replaced with a properly grounded three-prong wall receptacle.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
DO NOT USE AN EXTENSION CORD. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.
4
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed.
PREPARE THE OPENING
The Advantium/Convection 120 can be installed in combination with other GE Appliances/ Monogram appliances. Always follow each product’s Installation Instructions to complete the installation.
Single Advantium/Convection 120 Installation:
Order a 30” wide single oven cabinet or cut the opening in a wall to the dimensions shown.
30” 23-1/2”
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
25-1/4” |
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
17-1/2” |
|
|
|
|
|
Construct |
||
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
solid bottom |
|
|
|
|
|
|
|
|
|
|
|
- Min. 3/8” |
|
|
|
|
|
|
|
|
|
|
|
plywood |
|
|
|
|
|
|
|
|
|
|
|
supported |
|
|
|
|
|
|
|
|
|
|
|
on all four |
|
|
|
|
|
|
|
|
|
|
sides. Must |
|
36-3/4” |
|
|
|
|
|
|
|
|
|||
Min. |
|
|
|
|
|
|
|
|
|
be able to |
|
|
|
|
|
|
|
|
|
|
|
|
support |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
weight of |
|
|
|
|
|
|
|
|
|
|
|
oven and |
|
|
|
|
|
|
|
|
|
|
|
contents. |
•Allow 1-1/4” case trim overlap
at the top and 7/8” overlap on the bottom and 2-1/4” overlap for each side of the opening.
•Oven overlaps will conceal cut edges on all sides of the opening.
When installed over a single oven or a warming drawer, allow at least 2” between the two openings. This separation will provide clearance for bottom overlap of the Advantium/ Convection 120 and the other appliance overlaps.
•The support must be level and rigidly mounted, flush with the bottom edge of the cutout.
PREPARE THE OPENING (CONT.)
Installation over a GE Appliances/ Monogram Warming Drawer:
|
|
|
|
|
|
|
23-1/2” |
|
|
|
|
|
|
|||||||
30” |
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
Construct |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
solid bottom |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
- Min. 3/8” |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
plywood |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
supported |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
on all four |
|
|||
|
|
|
|
|
|
|
|
25-1/4” |
|
|
|
|
|
sides. Must be |
|
|||||
|
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
able to support |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
weight of oven |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
and contents. |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
17-1/2” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
2” Min. |
||||||||
|
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(3” Recommended) |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Per Warming |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drawer |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Requirement |
|
|
36-3/4” Min.
NOTE: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location does not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
5
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed.
PREPARE THE OPENING (CONT.)
Installation over a GE Applainces/ Monogram Oven:
30” 23-1/2”
25-1/4”
17-1/2”
45-1/4” Min.
*If you are replacing a GE Appliances/ Monogram electric double oven with the combined installation of an Advantium/ Convection 120 and a single oven, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2” minimum shown.
PREPARE THE OPENING (CONT.)
Installation over a GE Appliances/ Monogram Oven and Warming Drawer:
|
|
|
30” |
|
|
|
Construct |
|
|
|
|
||||||||||||||
|
|
|
|
|
|
solid bottom - |
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
23-1/2” |
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Min. 3/8” plywood |
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
supported |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
on all four sides. |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Must be able to |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
support weight |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
of oven and |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
25-1/4” |
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
contents. |
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
17- |
1/2” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2” Min. |
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(3” Recommended) |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Per Oven |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Requirement |
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2” Min. |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(3” Recommended) |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
45- |
1/4” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Per |
Warming |
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drawer |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Requirement |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
NOTE: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location does not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
CAUTION For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of the oven and drawer, plus additional oven loads.
6
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed.
PREPARE THE OPENING (cont.)
Installation over another GE Appliances/ Monogram Built-In SpeedCook Oven:
30Ǝ |
|
|
23-1/2Ǝ |
|
|
Construct |
||||||
|
|
|
|
solid bottom - Min. |
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
3/8” plywood |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
supported |
|
|
|
|
|
|
|
|
|
|
|
|
on all four sides. |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
Must be able to |
|
|
|
|
|
|
|
|
|
|
|
|
support weight |
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
25-1/4Ǝ |
|
|
|
of oven and |
||
|
|
|
|
|
|
|
|
|
|
|
|
contents. |
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
17-1/2Ǝ |
|
|
|
|
|
|
|
|
2Ǝ Min. |
|
|
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
(3Ǝ Recommended) |
|
|
|
|
|
|
|
|
|
|
|
|
|
17-1/2Ǝ
•If you are mounting a GE Appliances Appliances/Monogram Built-In SpeedCook Oven over another, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 2Ǝ minimum shown.
PREPARE THE OPENING (cont.)
Installation under a GE Appliances/ Monogram Microwave Oven and over a Warming Drawer:
30Ǝ |
|
|
|
|
|
|
Construct |
|
|
23-1/2Ǝ |
|
|
solid bottom - Min. |
||||
|
|
|
|
|
|
|
|
3/8” plywood |
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
supported |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
on all four sides. |
|
|
|
|
|
|
|
|
Must be able to |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
support weight |
|
|
|
25-1/4Ǝ |
|
|
|
of oven and |
|
|
|
|
|
|
|
|
|
contents. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Per Microwave
Oven Requirement 3.5Ǝ Min.
(4.5Ǝ Recommended)
17-1/2Ǝ |
|
|
2Ǝ Min. |
Per Warming |
(3Ǝ Recommended) |
Drawer |
|
Requirement |
|
NOTE: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
CAUTION For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of the oven and drawer, plus additional oven loads.
7
Standard Installation Preparation
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed.
PREPARE THE OPENING (cont.)
Installation beside another GE Appliances/Monogram Built-in Speedcook Oven:
•If you are mounting a GE Appliances/ Monogram Built-In SpeedCook Oven beside another, use the dimensions shown. The middle rail separating the two openings may need to be larger than the 4-1/2Ǝ minimum shown.
23-1/2Ǝ
25-1/4Ǝ 25-1/4Ǝ
17-1/2Ǝ
17-1/2Ǝ
4-1/2Ǝ Min.
(5-1/2Ǝ Recommended)
PREPARE THE OPENING (cont.)
Installation under a GE Appliances/Monogram 30Ǝ or 36Ǝ Cooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size. See the label on top of the oven for approved cooktop models. This oven requires a separate, properly grounded 15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36Ǝ or wider base cabinet.
|
1-1/2Ǝ Min. |
|
25Ǝ |
|
Cooktop |
|
Cooktop |
|
36Ǝ |
|
Countertop |
|
Height |
|
17-1/2Ǝ |
|
25-1/4Ǝ |
23-1/2Ǝ |
Cooktop height including depth |
of electrical box on some |
|
|
models. Refer to cooktop |
|
installation instructions. |
|
No minimum clearance required |
|
between cooktop and oven. |
NOTE: The oven is only approved to be installed 4Ǝ High under the specific models as labeled on the unit. Toekick
8
Flush Mount Installation Preparation (Monogram Only)
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed.
PREPARE THE INTERIOR
Cut and install side cleats:
•Cut side wood cleats to height of cabinet opening and approx. 2-1/2” in depth. Install, on each side, 1-3/8” from the front face of the cabinet.
Cut and install bottom cleat:
•Cut bottom wood cleat to a height of 1-1/8”, a depth of the cabinet minus 1-3/8” and a width of 25-1/4” to fit between side cleats. Install onto the cabinet floor between the side cleats, push it all the way back against cabinet wall and make sure its front face aligns with the front faces of the side cleats (1-3/8” gap from the front cabinet face).
|
A |
|
A |
|
|
C |
D |
|
B |
|
E |
A |
Side cleats depth |
2-1/2” min. |
|
B |
Bottom cleat height |
1-1/8” |
|
C |
Bottom cleat depth |
Cabinet depth minus 1-3/8” |
|
D |
Bottom cleat width |
25-1/4” |
|
E |
All three cleats |
Recess and install 1-3/8” |
|
|
|
IURPGHVLUHGÀXVKVXUIDFH |
|
D |
C |
TOP |
|
VIEW |
A |
A |
Front Face of Cabinet |
|
E |
E |
PREPARE THE OPENING
The Advantium 120 can be installed in combination with other GE Appliances/ Monogram appliances. Always follow each product’s Installation Instructions to complete the installation.
Single Advantium 120 Installation:
Cut the opening in a cabinet to the dimensions shown.
*See table below for desired reveals on sides.
**19-1/4”
36-3/4” Min.
23-1/2” min.
F *
Construct solid bottom - Min. 3/8” plywood supported on all four sides.
Must be able to support weight of oven and contents.
|
2” Min. |
|
Per |
Oven or |
appliance |
warming |
specs. |
drawer |
|
• The support must be level and rigidly mounted, flush with the bottom edge of the cutout.
Approved Flush Installation |
Dimension F |
|
1/8” Reveal |
1/4” Reveal |
|
Single Advantium |
30” |
30-1/4” |
Over Warming Drawer |
30” |
30-1/4” |
Over Oven |
30” |
30-1/4” |
Over Oven and Warming Drawer |
30” |
30-1/4” |
Over Built-in Speedcook Oven |
30” |
30-1/4” |
Double Advantium (side by side) |
See page 10 |
|
Under Cooktop or Countertop |
See page 10 |
** Top and bottom reveals are set to 1/8”.
9
Flush Mount Installation Preparation (Monogram Only)
IMPORTANT: Always maintain 36-3/4” minimum height from the floor to the cutout in any single or combined installation unless plastic trim is installed.
PREPARE THE OPENING |
|
|
|
|
|||
|
|
|
23-1/2” min. |
||||
|
|
|
|
||||
The Advantium/Convection 120 can be installed beside |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
another Advantium/Convection 120 in a side-by-side |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
combination. |
|
|
|
|
|
|
|
|
|
|
|||||
Double Advantium/Convection 120 |
G* |
||||||
H* |
|||||||
Installation: |
Cut the opening in a cabinet to the dimensions shown.
• Center divider acts as cleat for side of each respective |
|
|
|
|
|
|
|
|
|
|
|
|
I* |
|
|||||
|
|
|
|
|
|
|
|
|
I* |
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|||||||||||||
unit. Only one additional side cleat needed per oven |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
cutout. |
|
|
|
|
|
|
|
19-1/4” |
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|||||||||||||||
• The support must be level and rigidly mounted, flush |
|
|
|
|
|
|
|
|
|
|
1-3/8” |
||||||||
with the bottom edge of the cutout. |
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
*See table for desired reveals on sides and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
between unit. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dimension |
1/8” Reveal |
1/4” Reveal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
36-3/4” |
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
G |
59-7/8” |
60-1/4” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
Min. |
|
|
|
|
|
|
||||||||||
|
H |
5-1/8” |
5-1/4” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
I |
27-3/8” |
27-1/2” |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Construct solid bottom - Min. 3/8” |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
plywood supported on all four |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
sides. Must be able to support |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
weight of oven and contents. |
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Installation under a GE Appliances/Monogram 30Ǝ or 36Ǝ Cooktop or Countertop:
Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size. See the label on top of the oven for approved cooktop models. This oven requires a separate from the cooktop, properly grounded 15-Amp, 120-Volt, 60Hz power supply. Use a 36Ǝ or wider base cabinet.
23-1/2Ǝ
4Ǝ High
Toekick
1-1/2Ǝ Min.
|
|
|
|
|
|
|
|
|
|
|
|
25Ǝ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
Cooktop |
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Cooktop |
|
|
|
|
|
||||||||||
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
36Ǝ |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Countertop |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Height |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
19-1/4” |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
J* |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
Cooktop height including depth of electrical box on some |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
models. Refer to cooktop installation instructions. |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
No minimum clearance required between cooktop and |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
oven. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*See table for desired reveals on sides. |
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dimension |
1/8” |
1/4” |
|
|
NOTE: The oven is only approved to be |
|
|
|
Reveal |
Reveal |
|||||||||||||
|
|
|
J |
30” |
30-1/4” |
||||||||||||||
|
installed under the specific models as |
|
|
labeled on the unit.
10