GE PZS25KSEBFSS, PZS23KSEBFSS, PZS23KPEBFWV, PZS23KPEBFBV, PZS23KGEBFWW Owner’s Manual

...

GEAppliances.corn

"TD

C13

Safety Instructions ............ 2-4

Operating Instructions

Automatic Ice maker ........... 15, 16

Care and Cleaning ............. 18, 19

ClimateKeeper2 T".................... 6

Crispers and Pans .................. 14

CustomCooF" . .................... 7, 9

Ice and Water Dispenser ....... 17-18

Ouick Ice ........................... 17

Refrigerator Doors ................. 13

Replacing the Light Bulbs ........... 20

Set Features ........................ 6

Shelves and Bins ............... 11, 12

Temperature Controls ............... 5

TurboCooF" . ........................ 6

Water Filter ........................ 10

Installation Instructions

Installing the Refrigerator ....... 30-33

Moving the Refrigerator ........ 26-29

Preparing to Install

the Refrigerator .................... 25

Trim Kits and Panels ............ 21-24

Water Line Installation ......... 34-36

Models 22, 23, 25, 26, 27 ond 29

Profile CSte6 CSte

La section fran_aise commence _ la page 47

Profile Lado a Lado

Refrigeradores

La secci6n en espaflol empieza en la p6gina 93

Troubleshooting Tips ...... 38-4o

Normal Operating Sounds.......... 37

Consumer Support

Performance Data Sheet ........ 43,44

State of California Water

Treatment Device Certificate ........ 46

Warranty (Canadian) ............... 41

Warranty (U.S.) ..................... 42

Write the model end serial numbers

here:

Model #

Serial #

Find these numbers on a label inside

the refrigerator compartment at the

top on the right side.

200D8074P052 49-60647-2 07-13 GE

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

, This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is used.

, Do not allow children to climb,stand or hang on the shelves

in the refrigerator. They could damage the refrigerator and seriouslyinjurethemselves.

, Do not touch the cold surfaces in the freezercompartment

when hands are damp or wet.

Skinmaystickto these extremely cold surfaces.

, Do not store or usegasoline or other flammable vapors and

liquidsinthe vicinity of this or any other appliance.

, In refrigerators with automatic ice makers,avoid contact

with the moving parts of the ejector mechanism, orwith the

heating element located on the bottom of the ice maker. Do not placefingers or hands on the automatic icemaking

mechanism while the refrigerator is plugged in.

Keepfingers out of the "pinch point" areas; clearances between the doors and between the doors and cabinet are

necessarilysmall. Becareful closing doors when children are inthe area.

, Unplug the refrigerator before cleaning and making repairs.

NOTE:We strongly recommend that any servicing be performed by a qualified individual

, Non-LCO models: Setting either or both controls to 0 [ofg

does not remove power to the light circuit.

, LCDmodels: Turning the cooling system off does not remove

power to the light circuit.

, Donot refreezefrozen foods which havethawed completely. , Always clean the CustomCool'" Tray after thawing food.

A DANGER! RISK OF CHILD ENTRAPMENT

PROPERDISPOSAL OF THE REFRIGERATOR

GEAppliances.com

Childentrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous...evenif

they will sit for 'lust a few days." Ifyou are getting rid of your old refrigerator, please follow the instructions below to help prevent

accidents.

Before You Throw Awuy Your Old Refrigerutor or Freezer'.

Takeoff the doors.

Leavethe shelvesin place so that children may not easily

climb inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you

are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

USEOF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of on extension

cord.

However, ifyou must use an extension cord, it is absolutely necessary that it be a UL-listed(inthe United States)or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be !5 amperes (minimum) and !20 volts.

IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.

A WARNING!

HOW TOCONNECTELECTRICITY

Do not, under anycircumstances,cut orremove the third [ground)prong from the power cord.Forpersonal safety,this appliance must beproperly grounded.

The power cord of this appliance isequipped with a:S-prong (grounding) plug which mates with a standard :S-prong

(grounding) wall outlet to minimizethe possibility of electric shock hazard from this appliance.

Havethe wall outlet and circuit checked bya qualified

electrician to make surethe outlet isproperly grounded.

Ifthe outlet is a standard 2-prong outlet, it isyour personal

responsibility and obligation to have it replacedwith a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into itsown individual electrical outlet which has avoltage rating that matches the

rating plate.

Thisprovides the best performance and also prevents overloading house wiring circuits which could causea fire

hazard from overheated wires.

Neverunplug your refrigerator by pulling onthe power cord.

Alwaysgrip plug firmly and pull straight out from the outlet.

Repairor replace immediately all power cords that have

become frayed or otherwise damaged. Donot use acord that shows cracks or abrasion damage along its length or at either

end. When moving the refrigerator away from the wall, be careful not

to roll over or damage the power cord.

READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

About the temperature controls. GEAppliances.com

Not all features are on all models. Your controls may be similar to the following:

Temperature

Touch-LED Dispenser Control

NOTE:Therefrigeratorisshippedwith

protective filmcoveringthe temperature

controls.Ifthisfilmwasnot removed duringinstallation,removeit now.

Thetemperaturecontrolsarepresetinthe factoryat37°F(3°C)forthe refrigeratorcompartmentandO°F(-!8°C)forthe freezercompartment

Allow24 hoursforthetemperaturetostabilizeto thepreset

recommendedsettings. Refrigeratortemperaturescanbeadjustedbetween54°Fand46°F

(1°Cto8°C),andthefreezertemperaturescanbeadjustedbetween-6% and+8°F(-21°Cto-13°0.

To change the Refrigerator temperature: Tactile-LED Dispenser Control

Thetemperaturecontrolscandisplayboththe SETtemperatureaswell

asthe actualtemperatureinthe refrigeratorandfreezer.Theactual temperaturemayvaryslightlyfromtheSETtemperaturebasedon

usageandoperatingenvironment.

Onsomemodels,settingbothcontrolstothewarmestsettinguntil thedisplayflashes(off)will stopcoolinginboth thefreezerand

refrigeratorcompartments.

Onothermodels,settingeithercontroltothewarmestsetting

untilthedisplayflashes(off)willstopthecoolingto thefreezerand refrigerator.

NOTE:Turningtherefrigeratoroffvia thecontrolsonthe touch paneldoesnotshutoffelectricalpowertothe refrigerator.

NOTE:Therefrigeratorisshippedwithprotectivefilmcoveringthe temperaturecontrols,tfthisfilmwasnot removedduringinstallation,

removeit now.

Touch-LEDDispenser Control', Tochange the temperature, press and release the FREEZER

TEMP/FRIDGETENPpad TheSETlight will come on and

the display will show the settemperature. To change the temperature, tap either the A or V pad until the desired temperature is displayed.

Recommended 0 o F Recommended 37 ° F

m ActuelTemp Set Temp i

Tactile LED Dispenser Control.

Oncethe desiredtemperature has been set, the temperature display will return to the actual refrigerator and freezer temperatures after 5 seconds.Severaladjustments may be

required. Each time you adjust the controls,allow 2/4hours for the refrigerator to reach the temperature you have set.

ThetemperaturecontrolscandisplayboththeSETtemperatureaswell asthe actualtemperatureintherefrigeratorandfreezer.Theactual

temperaturemayvaryslightlyfromtheSETtemperaturebasedon usageandoperatingenvironment.

Turning the cooling system off: Tactile-LED Dispenser Control

Onsomemodels,settingbothcontrolstothewarmestsettinguntil thedisplayflashes(off)will stopcoolinginboth thefreezerand

refrigeratorcompartments.

Onothermodels,settingeithercontroltothewarmestsetting

untilthedisplayflashes(off!willstopthecoolingto thefreezerand refrigerator.

NOTE:Turningtherefrigeratoroffvia thecontrolsonthe touch paneldoesnotshutoffelectricalpowertotherefrigerator.

Touch-LEDDispenser Control:

Press and release the FREEZERTEPIP/FRIDGETENPpad. Press ^to set freezer temperature to 5.The display will

show OFF.To turn the unit back on, press the FREEZER TEMP/FRIDGETENP pad. Press ^ to set the freezer and

refrigerator temperatures to the preset points of 0% (-18°C) for the freezer and 37°F (3°C)for the refrigerator.

When the unit is turned back on, it will take up to 24 hours to stabilize.

Performance Air Flow S stem

ThePerformance Air-Flow System isdesignedto maximize temperature control in the refrigerator and freezer

compartments. This unique special feature consists ofthe AirTower along the back wall of the refrigerator and the Air

Tunnelon the bottom portion ofthe freezer rear wall. Placing food in front of the louvers on these components will not affect

performance. Although the AirTower and the AirTunnel can be removed, doing so will affect temperature performance.

(Forremoval instructions, on-line, contact usat ge.com or call

800.GECARES.InCanada,contact usat geappliances.caor call

1.800.561.3344.)

About Set Features.

Thispad is used to selectthe following features: TurboCool, Quick Ice,Door Alarm and Water

Filter.

About TurboCool.TM

How it Works

TurboCool _"rapidly coolsthe refrigerator compartment in order to more quickly cool foods. UseTurboCoolT"when adding

boC

a large amount of food to the refrigerator comportment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers.Itcan also be usedif the refrigerator has beenwithout power for an extended period.

Onceactivated, the compressor will turn on immediately and the fans will cycle on and off at high speedas needed for eight hours. Thecompressorwill continue to run until the refrigerator compartment cools to approximately 34% (I°C),then itwill cycleon and off to maintain this setting. After 8 hours,or if TurboCool" is pressedagain, the refrigerator compartment will return to the original setting.

How to Use

Tactile LEDDispenser Control:

PressTurboCoolTM. TheTu.rboCooltemperature , displaywillshowTcandtheLEDwillbeactivated.

AfterTurboCooPiscomplete,theTurboCooP indicatorlightwill goout.

PressingSETFEATURESrepeatedly will cycle

through all of the available features and then exit the mode. If no keyis pressed,the mode

will exit and return to displaying features currently set.

NOTES:Therefriqerutortemperaturecannotbe

chungedduringTurboCooP.

Thefreezertemperatureis notaffected

duringTurboCool_".

Wh.enope.ninqtherefrigeratordoorduring TurboCooF",thefunswillcontinuetorunIt

they hovecycledon.

Touch-LEDDispenser Controls:

PressSETFEATURES.Therefrigerator

temperature display will show TurboCool_"

and/or TC. PressON/OFF.

After TurboCooP iscomplete, the refrigerator

compartment will return to the original setting.

NOTES: Therefrigerator temperature cannot bechanged

during TurboCool_". Thefreezertemperature isnot affected during

TurboCooF".

When opening the refrigerator door during

TurboCooF', the fans will continue to run if they

have cycled on.

About ClimateKeeper2;" Ionsome models)

How it Works

TheClimateKeeper2TM isthe industry's most advanced refrigeration system,delivering

optimum temperature and humidity performance to keepfood garden fresh longer

and reduce freezer burn. TheClimateKeeperZ" system features two

evaporators-one for the refrigerator and one for the freezer.

Thisprovides two separate cooling systems, and separates the airflow betweenthe fresh

food and freezer compartments during normal cooling operations.*

Thisensures that the humidity levelsin the fresh food compartment are significantly higher

than in a conventional system,**allowing fresh produce and other unsealed foods to retain

their moisture content and freshness longer.

Moisturesensitivefoods such as freshfruit,

salads,rice,etc.,can now be stored on open shelveswithout excessivemoisture loss.

Dueto the higher humidity inthe refrigerator,

you may on occasion experiencefog or

small amounts of moisture in the refrigerator compartment. This isnormal and may

come and go as different food loads and environmental conditions change.Wipe dry

with a paper towel ifdesired. Theseparate airflow system minimizesthe

mixing of air between the two compartments,

which reduces fresh food odor transfer to

improve the taste of ice.

TheClimateKeeperZ" system also reduces the number of defrosting cycles inthe freezer

evaporator, thereby reducing freezer burn. *Freezerair is usedin the CustomCool feature.

**Testingshows a higher levelof humidity in

theFreshFood sectioninClimateKeeperZ" refrigeratorsversusconventional units.

About CustomCoolf(onsome models) GEAppliances.com

ExpressThawTM

How it Works

Touch LED Dispenser Control

TheCustomCoor" feature isused to quickly chill items,thaw items or holdthe pan at a specific temperature. Thisfeature isasystem of

dampers, a fan, a temperature thermistor and a heater.

How to Use

Emptythe pan.Placethe Chill/Thawtray in

the pan. Placethe itemson the tray and close the pan completely.

Touch LEDDispenser Control:

Selectthe ExpressThawTM, ExpressChilr" or SelectTempTM pad.Thedisplay and SET light will come on.Tap the pad until the light appears next to the desired setting.

Usethe following chart to determine the best setting to use,

ExpressChill can be set to 15,30 or/45

minutes.Thedefault is 15 minutes.

Tostop a feature before it is finished: tap that feature's pad until no options are selected and the display isoff.

Thepan istightly sealedto preventtemperature fluctuations inthe rest of the refrigerator. Thecontrols for this pan are located on the

dispenser with the temperature controls.

DuringExpressThaw and ExpressChill,the display on the controls will count down the time inthe cycle (onsome models).

After the ExpressThaw cycle is complete, the pan will resetto the MEATsetting (32%

[0°C])to helppreservethawed items until they are used.

Thedisplayedactual temperature of the CustomCool pan may vary slightly from the SETtemperature based on usage and operating environment.

NOTE:Forfood safetyreasons,it is recommended that foods be wrapped in plastic wrap when usingExpressThaw. Thiswill help contain meatjuices and improve thawing performance.

ExpressChillm_

About ExpressChillflon some models)

..........................................................• SET

How if: Works

ExpressChi//

ExpressChill_

TheExpressChilF"feature isasystem of dampers, a fan and a temperature thermistor.

Thepan istightly sealedto preventthe pan's temperature from causing temperature

fluctuations inthe rest of the refrigerator.

How to Use

Emptythe pun. Placethe Chilltray in the pan.Placethe items on the tray and close

the pan completely. Selectthe ExpressChill'" pad. On some

models,you can then select the chilltime

(usechart to determine best setting).Other models will only have one option (45

minutes).On models with multiple settings, tap the pad until the light appears nextto the desired setting.

Thecontrols for this pan are located in the top of the refrigerator or onthe dispenserwith the

temperature controls.

, To stop a feature before it isfinished,tap

that feature's pad until no options are selectedand the display isoff.

, During ExpressChill,thedisplay on the

controls will count down the time inthe cycle.

How to Remove and Replace the Drawer To remove: 0 Lock all four swing locks by rotating them

Pullthe drawer out to the stop position, to the lock position.

Rotateallfour swing locksto the unlock position.

Liftthe front of the drawer up and out.

To replace:

Hake sure all four swing locks are inthe unlock position.

Place the sides of the drawer into the drawer supports, making sure the swing

locks fit on the drawer slots.

About CustomCoolF(onsome models) GEAppliances.com

CustomCool TM Chart

NOTE:Results may vary depending on packaging, starting temperature and other food traits.

Express Thaw" ExpressChill'"

0.5 Lb. (4 hours) 15 Minutes

Hamburger Patties(0.5 Ib) ! Beverage Can(12oz) IndividuallyWrapped 2 SmallJuiceBoxes(6-8 oz each) FiletMignon (0.5Ib) 30 Minutes

Chicken Breasts(1.0Ib) Ground Beef(1.0Ib)

Steak (1.0Ib) (6-8 oz each)

Chicken Breasts(2.0Ibs) Wine (750ml bottle) Ground Beef(2.0Ibs) 45 Minutes

Steak (2.0Ibs) 2 Literof Beverage

Chicken Breasts(3.0Ibs) Gelatin-1 package Ground Beef(3.0Ibs)

Steak (3.0Ibs)

1.OLb.16hours} 2to 6 Beverage Cans(12oz each) 2 Plastic20oz Bottlesof Beverage

a to 6 Small Juice Boxes

2.0 Lbs.!10 hours} 3 FoilJuice Packets

3.0 Lbs.(12hours} 1/2 Gallon of Juice

SelectTemp T"

Citrus Settinq (43°F[6°C])

Oranges, Lemons,Limes,Pineapple, Cantaloupe

Beans,Cucumbers,Tomatoes, Peppers,Eggplant,Squash

Produce Settinq (35°F[2°C]}

Strawberries, Raspberries,Kiwifruit,

Pears,Cherries,Blackberries,Grapes, Plums,Nectarines, Apples

Asparagus, Broccoli,Corn,

Mushrooms,Spinach,Cauliflower, Kale,GreenOnion, Beets,Onions

Meat Settinq (32°F[O°C])

Raw Meat,Fishand Poultry

About the water filter, (on some models)

Water Filter Cartridge

Thewater filter cartridge is located in the back upper right corner of the refrigerator compartment.

Cartrid

When to Replace the Filter on Models With a Replacement Indicator Light

Thereisa replacement indicator light for the water filter cartridge on the dispenser.This light will turn orange to tellyou

that you need to replacethe filter soon. Thefiltercartridge should bereplaced when the replacement

indicator lightturns red or if the flow of water to the dispenseror ice maker decreases.

When to Replace the Filter on Models Without a Replacement Indicator Light

Thefiltercartridge should bereplaced every six months or earlier if the flow of water to the water dispenser or ice maker

decreases.

Removing the Filter Cartridge

If you are replacing the cartridge,first remove the oldone by slowly turning it to the left. Do not pull down on the cartridge. A

small amount of water may drip down.

Installing the Filter Cartridge

0 Ifyou are replacing a SmartWater cartridge with an

adapter, itmust be removed before installing the cartridge.

To remove the adapter, turn it to the leftabout !/a, turn.

If you are replacing a Water by Culligan cartridge, leave the adapter in place.Thisadapter will stay in the refrigerator when

you replace future cartridges.

HoIder_

Runwater from the dispenser1-1/2 gallons (aboutthree

minutes)to clear the system and prevent sputtering. Pressand hold the WATERFILTERpad (onsome models)on

the dispenser for 3 seconds.

Reset

Hold 3 Sec

NOTE:A newly-installed water filter cartridge may cause water to spurt from the dispenseruponfirst use.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge isnot available. Thedispenserandthe icemaker will

not operate without the filter orfilter bypass plug.

SrnartWater Water byCulligan

Some models

With adapter

(appearance may vary)

O On models without a replacement indicator light, apply the

month and year sticker to the new cartridge to remind you

to replace the filter insix months.

Fillthe replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after

installation.

Lineup the arrow on the cartridge and the cartridge holder. Placethe top of the new cartridge up insidethe holder.Do

not push it up into the holder. Slowlyturn itto the right until the filter cartridge stops.

DONOTOVERTIGHTEN.Asyou turn the cartridge, itwill automatically raise itselfinto position.The cartridge will move about 1/2 turn.

Without adapter water

pe.o

Tousethe filter bypass plug on Water byCulligan models,you must first remove the filter adapter from the cartridge holder by turning it to the left.

Forthe maximum benefit ofyour filtration system, GE recommends the useof GEbranded SmartWater filters only. Using GEbranded filters in GEand Hotpoint refrigerators provides optimal performance and reliability.GEbranded SmartWater filters are always the right choicebecausethey are patented and designed specificallyfor GEproducts. GE SmartWater filters meet rigorous industry NSFstandards for safety and quality that are important for products that are filtering your water. GEhas not qualified non-GEbranded filters for use in GEand Hotpoint refrigerators and there isno

assurance that non-GEbranded filters meet GE'sstandards for quality, performance and reliability.

If you have questions-visit our Websiteat GEAppliances.com,or call !.800.GE.CARES(1.800.4322737).

Replacement filters: To order additional filter cartridges in the United States,

visit our Website at GEAppliances.com, or call GEParts and Accessories, 800.626.2002.

See filter label for type of filter to order (PIWFor kISWF). Customers in Canada should consult the yellow pages for the

nearest klabe Service Center.

About the shelves and bins.

Not all features are on all models.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Bins

The larger refrigerator door bins andfreezer tilt-out door bins areadjustable.

Toremove: Liftthe front of the bin straight up,

then lift up and out.

Refrigerator am

Freezer tilt-out am

To replace or relocate: Engage the back side of the bin in the molded supports on the door.

Then push down on the front of the bin. Binwill

lock in place. Thesnugger helps prevent tipping, spilling or

slidingof small items stored on the door shelf. Placea finger on either sideof the snugger

near the rear and move it back andforth

to fit your needs.

Top Freezer Bins

DOn0t biock

Top freezer bin

Do not block

iii

GEAppliances.com

CAUTION: Be careful when

placing items in

the top bin. Make sure that items

do not block or

fall into the ice chute.

CAUTION: Partmust be in

placeas shown for proper ice

dispensing.Food

cannot be stored in this location.

5 if¸¸¸:::::I¸¸:¸¸¸I¸¸

Press tab and pull shelf forward to remove

:::::::

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to

reach items stored behind others. The special edges are designed to help prevent spills from

dripping to lower shelves.

To remove:

Slidethe shelf out until it reaches the stop,

then press down on the tub and slide the shelf

straight out.

QuickSpuce'" Shelf

This shelf splitsin half and slidesunder itselffor

storage oftall items on the shelf below.

This shelf can be removed and replaced or

relocated just likeSlide-Out SpillproofShelves.

Top freezer bin (on some models)

To replace or relocate:

Linethe shelf up with the supports and slide it into place.The shelf can be repositioned

when the door isat 90° or more. To reposition the shelf, slidethe shelf past the stops and

angle downward. Slideshelfdown to the desired position, line up with the supports and

slideinto place.

Make sure you push the shelves all the way back in before you close the door.

On some models,this shelf cannot be used in the lowest position.

About the shelves and bins.

Not all features are on all models.

Freezer Baskets

Toremove, pushthe basket all the way to the back of the freezer. Lift up until the back pins

are disengaged. Liftthe entire basket up and pull out.

Slide-Out Freezer Shelves

Toremove, slideout to the stop position, lift the

front post the stop position and slideout.

Fixed Freezer Shelves

There are two types of fixed freezer shelves.

Toremove this type of shelf:

0 Lift the shelf up at the left side. 0 Bring the shelf out.

Toremove this type of shelf:

Lift up the left side of the shelfand slide it left into the center of the shelfsupports.

Make sure you push the baskets oll the way 8ock in Beforeyou close the door.

Make sure you push the shelves oil the way

back in beforeyou close the door.

NOTE FOR DISPENSERMODELS: In order to take full advantage of the tilt-out ice bin, only

store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Rotatethe right sideof the shelfup and out of the shelf supports.

Door Wine/Beverage Rack (onsome models)

This rack holdsup to 5 cons or one bottle of wine.

The rock hangs from the sides of the dairy bin.

Toremove:

Empty the wine/beverage rock. Holding the bottom of the dairy bin,lift the

front straight up, then lift up and out. Todetach the rock from the dairy bin,pull

the rock's sidewires out of the holeson each side of the dairy bin.

Toreplace:

Reattochthe rack to the sidesof the bin. Engagethe back side of the bin in the

molded supports on the door.Then push

down on the front of the bin.The binwill lock into place.

About the refrigerator doors. GEAppliances.com

Refrigerator Doors

When the door is only partially open, it will automatically close.

Beyond this stop the door will stay open.

The refrigerator doors may feel different th(]n the ones you (]reused to.The speci(]ldoor

opening/closing fe(]ture m(]kes surethe doors close(]11the w(]y (]nd (]re securely se(]led.

When opening (]nd closingthe door,you will

notice (]stop position. If the door is opened p(]stthis stop point, the door will rem(]in open

to (]llow you to Io(]d (]nd unlo(]dfood more

e(]sily.When the door isonly p(]rti(]lly open,it

will (]utom(]tic(]lly close.

Door Alignment

If doors (]re uneven,(]djust the refriger(]tor door.

Using(] 7/16" wrench, turn the door

(]djusting screw to the right to r(]isethe door, to the left to lower it. (Anylon plug,

imbedded in the thre(]ds of the pin, preventsthe pin from turning unless(]

wrench isused.)

Theresist(]nceyou feel (]tthe stop position will be reduced (]s the door is Io(]dedwith food.

O After one or two turns of the wrench,

open (]nd close the refriger(]tor door (]nd check the (]lignment (]t the top of the

doors.

About the crispers and pans.

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in

the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has

full extension slidesthat allow full access to the drawer.

HI LO

2_ "

Adjustable Humidity Crispers

Slidethe control all the way to the HIsetting to provide high humidity recommended for most

vegetables.

Convertible Oeli Pan

Theconvertible deli pan has its own cold

air duct to allow a stream of cold air from

the freezer compartment or freshfood

compartment to flow to the pan.

i i _i i iiiii

Thevariable temperature control regulates

the air flow from the Climate KeeperAir Tower.

About crisper removal.

Not all features are on all models.

Slidethe control all the way to the LO setting to provide lower humidity levels recommended for most fruits.

Setthe control to the coldest setting to store fresh meats.

Setthe control to cold to convert the pan

to normal refrigerator temperature and provide

extra vegetable storagespace.

The cold air duct isturned off.Variable settings

between these extremes can be selected.

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up

and over the stop location.

If the door prevents you from taking out the drawers,first try to remove the door bins.

If this does not offer enough clearance, the refrigerator will need to be rolledforward

until the door opens enough to slidethe drawers out. Insome cases,when you roll the

refrigerator out, you will needto move the refrigerator to the left or right asyou roll it out.

About the automatic ice maker. GEAppliances.com

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Ice maker

Theice maker will produce seven cubes per cycle- approximately 100-!30 cubes in a 24-hour period, depending

on freezer compartment temperature, room temperature, number of door openings and other useconditions.

If the refrigerator isoperated before the water connection is made to the ice maker, setthe power switch in the OFFposition.

When the refrigerator has been connected to the water supply, set the power switch to the ONposition.

Theicemaker willfillwith water when itcoolsto 15°F(-10°O. A newly installedrefrigerator may take !2 to 24hoursto begin

making icecubes. Youwill hear a buzzing sound each time the ice maker fills with

water. Throw away the first few batches of iceto allow the water line

to clear. Besure nothing interfereswith the sweep of the feeler arm.

When the bin fillsto the levelof the feeler arm, the ice maker will stop producing ice.It is normal for several cubes to bejoined

together. If ice is not used frequently, old ice cubes will become cloudy,

taste stale and shrink.

Special note about dispenser models: , Some models have a tilt-out icebin.Thebin can be tilted out

asshown in the illustrations,and it will hold itself up while you

take iceout or turn the ice maker power switch on and off. Be

sureto put the bin back in place before closingthe door.

, To restore your ice level from an empty bucket stage, the

following steps are recommended:

O !2 hours after the first batch of ice hasfallen intothe bin,

dispense 3 to/4 cubes.

O After an additional 6 hours, dispense3 to 4 cubesagain. Thesestepswill restoreyour ice levelinthe shortest amount of

time.

ice maker

Power

Switch

ice maker

Switch CeelerArm

(on some models)

NOTE: In homes with lower than average water pressure, you may

hear the ice maker cycle multiple times when making one batch of ice.

Green

Power Ligm FeelerArm

(onsome models)

About the automatic ice maker. (cant)

Accessing Ice and Reaching the Power Switch on

Dispenser Models

There are two types of ice storage bins on dispenser models. One has a shelf above the bin,the other does not.

Special note for models with tilt-out ice bin:

These models have a tilt-out ice bin. The bin can be tilted out as shown in the illustrations, and it willhold itself up

while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before

closing the door.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the

bin.

Models with a shelf above the ice bin

i¸

To access ice, pull the bin forward.

!ii

......... -- .......... i

iiiii_

To reach the power switch, pull the shelf straight out. Always be sure to

replace the shel_

i ill

Models with tilt out ice bin

To access ice and reach the icemaker power switch:

O Lift the bin, then it forward

until the bin stops.

pull

O Lower the bin to access ice or

reach the power switch.

Removing Ice Bin (dispenser models) CAUTION:The ice bin is heavy when full.

Set the power switch to the OFFposition before removing the bin.

When replacing the bin, be sureto press it firmly into place,If

it does not go all the way back, remove it and rotate the drive mechanism !//4 turn. Then push the bin back again.

On some models, to access

O Pull the bin forward until the

bin stops.

Rotate

ice or reach the power switch:

O Lower the bin to access ice or

reach the power switch.

Drive Mechanism

Dispenser Models only

About the ice and water dispenser. (on some models) GEAppliances.com

To Use the Dispenser

SpillShelf

SelectCUBED,CRUSHEDor WATER. Pressthe glassgentlyagainstthetop

ofthedispensercradle.

Thespillshelfisnotself-draining.Toreducewater

spot!ing,the shelfand itsgrilleshouldbecleaned regulany.

tfnowater isdispensedwhenthe refrigeratorisfirst installed,theremaybeairinthewater linesystem. Pressthe dispenserarm forat leasttwo minutesto removetrappedairfromthewaterlineandto fillthe

water system.Toflushoutimpuritiesin thewater

line,throwawaythefirstsixglassfulsofwater. CAUTION:Neverput fingersoranyotherobjectsinto

theicecrusherdischargeopening.

Locking the Dispenser

Pressthe LOCKorLOCKCONTROLSpadfor 3secondsto lockthe dispenserandcontrolpanel.To unlock,pressand holdthepadagainfor

3seconds.

DispenserLight

TheLIGHTpadturnsthenight light inthe#spenser

onandoff.Thelightalsocomesonwhenthe dispensercradleispressed.Formodelswith a bulb,

ifthelightburnsout,it shouldbereplacedwith a 6 watt 12Vmaximumbulb.ForLEDmodelscontact

FactoryService.

OoorAlarm

UseDoorAlarm to soundif eitherdoorisopen formorethan3minutes.Thealarmwillstop oncethedoor isclosed.ForLCDmodels,a popup screenwillaRpear.Thealarmcanbesilenced bytouchingtheLCDscreen.

TouchLEDDispenserControl: Pressthe SETFEATURESpadonceandDOOR

ALARMwill blink.PressON/OFFandthedooralarm

willbesetandtheiconwillturnsolid.PressON/OFF againtoturnthealarmoff.

Door Alarm (onTactile LEDDispenserControl model)

Tosetthe alarm, press this pad until the

indicator light comes on. Thisalarm will sound if either

door is open for more than 3 minutes. The light goesout and the beeping stops when you closethe door.

Quick Ice

Whenyouneedtospeedupiceproduction,usethe QuickIcefeature.Whilethisfeatureisturnedon,

thefreezerfanrunscontinuouslyfor48hours,or untilthefeatureisturnedOFF.Duringthisperiod,ice productionwill increaseupto40%.Modelswiththe integratedicefeaturesystemrequireatFIRSTUSEat leasthalfan8oz.glassof icetobedispensedevery6 to12hours.Thiswillhelptheicemakerfillthebucket properlysothatdispensingisbetter.

Precise Fill (on some models)

Thiswaterdispenserisequippedwithafeature

called"precisefill."Thisfeatureallowsyouto choose a preciseamountof water(cupsor ounces)that

youwouldlikedispensed.PintsandLitersarealso

availableforLCDmodels.

TouchLEDDispenserControl

0 Pressthe PRECISEFILLCUPS/OZpad.

TheWATERpadwill lightandtheCRUSHED andCUBEDicepadswillturnoff.Thelastunit usedwillbedisplayed.

O Pressthe PRECISEFILLpadagainto toggle

betweencupsandounces.

Ifyou selectedOUNCES,pressthe A arM pad to selectthenumberofouncesyouwouldlike to havedispensedbetween2-99ounces.

Thedefaultis 8ounces.

Howto Use

TouchLEDDispenserControl:

PresstheSETFEATURESpadtwiceand QUICK!CE

willblink.PressON/OFFtoturntheteatureon then ago ntoturn toff.

Quick Ice (onTactile LEDDispenserControl

model)

[] When you need icein a

I '_ hurry, pressthis pad tO .

Quick J speed upice production.This

_ce tar the following 48hours

will increase ice production

or until you pressthe pad again.

Ifyou selected CUPS, pressthe A or v pad to select the amount you would liketo havedispensed.

They are displayedas 1/4, 1/3, 1/2,2/3 and 3/4,with

the highest amount being 16 3/4 cups.The default is i cup.

O Pressthe cup against the cradle and water will

begindispensing. Itwill automatically stop when the amount sethas been dispensed.The display will show the amount of water dispensed,beep,

then resetafter 5 seconds.

NOTE:Do not leavethe dispenser unattended when water isbeing dispensed.

Ifyou would liketo stop dispensing water before the specified amount has been

dispensed,just remove the cup from the cradle. Thedisplay will show the amount that has been dispensed for 5 seconds. Ifthe cup switch is pressed again within that time, the dispenser will continue up to the setamount. If not,the display will return to the set amount.

About the ice end water dispenser. Consome models)

important Facts About Your Dispenser

Do not add icefrom trays or bags to the storage drawer. It may not crush or dispense well.

Avoid overfilling glass with ice and use of narrow glasses. Backed-up ice can

jam the chute or cause the door in the

chute to freeze shut. If ice is blocking the chute, poke it through with a wooden spoon.

Beverages and foods should not be quick-chilled in the ice storage drawer. Cans, bottles or food packages inthe storage drawer may cause the ice

maker or auger to jam. To keep dispensed ice from missing the

glass, put the glass close to, but not touching, the dispenser opening.

Some crushed ice may be dispensed even though you selected CUBED.

This happens occasionally when afew

cubes accidentally get directed to

the crusher. After crushed ice is dispensed, some

water may drip from the chute.

Sometimes a small mound of snow

will form on the door in the ice chute. This condition is normal and usually

occurs when you have dispensed crushed ice repeatedly. The snow

will eventually evaporate.

Care and cleaning of the refrigerator.

Cleaning the Outside

Thestainless steel panels and door handles

Dispenser drip area.

Thedispenser drip area, beneaththe grille,

shouldbewiped dry.Water left in this area may leavedeposits.Removethe deposits

by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose

enough to rinseaway. Thedispenser cradle. Beforecleaning,

lock the dispenser by pressingand holding the LOCKor LOCKCONTROLSpadfor

3 seconds.Cleanwith warm water and baking soda solution-about a tablespoon

(15 ml)of baking soda to a quart (1liter) of water. Rinsethoroughly and wipe dry.

Thedoor handles end trim. Cleanwith a cloth dampened with soapy water.

Drywith a soft cloth.

(onsome models)can becleanedwith a commercially available stainlesssteel cleaner.A spray-on stainless steel cleaner

works best.

Do not useappliance wax or polish on the stainless steel.

Keepthe outside clean. Wipe with a clean cloth lightly dampened with kitchen

appliancewax or mild liquid dishdetergent. Dry and polishwith a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave

a residue that can erode the paint. Do not usescouring pads, powdered cleaners,

bleach or cleaners containing bleach because these products can scratch and

weaken the paint finish.

Cleaning the inside

Tohelp prevent odors, leave an open box

of baking soda in the freshfood and freezer compartments.

Unplug the refrigerator before cleaning.

Ifthis isnot practical, wring excessmoisture

out of sponge or cloth when cleaning around switches, lights or controls.

Usewarm water and baking soda solution- about a tablespoon (15ml) of baking sodato a quart (1liter)of water.This both cleans and

neutralizes odors. Rinseand wipe dry.

Use of any cleaning solution other than

that which is recommended, especially those that contain petroleum distillates,

can crock or damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot

water because the extreme temperature

difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the dishwasher.

Thechill/thaw tray is dishwasher safe.

Behind the Refrigerator

Becareful when moving the refrigerator away

from the wall. All types of floor coverings can

be damaged, particularly cushioned coverings and those with embossedsurfaces.

Pullthe refrigerator straight out and return it

to position by pushing it straight in.Movingthe

refrigerator in a sidedirection may result in damage to the floor covering or refrigerator.

Preparing for Vacation

Forlongvacations or absences,remove food and unplug the refrigerator. Cleanthe interior

with a baking soda solution of one tablespoon (15 ml)of baking soda to one quart (! liter) of

water. Leavethe doors open. Setthe icemaker power switch to the 0 (off)

position and shut offthe water supply to the

refrigerator.

GEAppliances.com

When pushing the refrigerator back, make sureyou don't roll over the power cord or ice maker supply line.

Ifthe temperature can drop below freezing,

have a qualified servicerdrain the water supply systemto prevent serious property

damage due to flooding.

Preparing to Move

Secureall loose items such as shelvesand drawers bytaping them securelyin place to

prevent damage. When using a hand truck to movethe

refrigerator, do not restthe front or back of the

refrigerator against the hand truck. This could damage the refrigerator. Handle only from the

sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

Replacing the light bulbs.consome models)

NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator or to the light circuit.

Yourlight shieldwill looklike oneof thefollowing:

Refrigerator Compartment--Upper Light

0 Unplug the refrigerator.

Thebulbs are located at the top ofthe compartment, insidethe light shield.On some models,a screw at the front of the

light shield will have to be removed.On

other models, the screw islocated in the pocket located at the back of the light

shield. Toremove the light shield, on some models,

press in on the tabs on the sidesof the shieldand slide forward and out. On other

models,just slide the shield forward and out.

Refrigerator Compartment--Lower Light This light is located above the top drawer. _ After replacing the bulb with an appliance

Unplug the refrigerator, the shield and the knob. Remove the convertible meat drawer

control knob by pulling straight out. _ Plug the refrigerator back in.

j 0 Liftthe light shield up and pull it out.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light shield.

(The shelf willbe easier to remove ifit is emptied first.) On some models, a screw at

the top of the light shield willneed to be removed.

Toremove the light shield, press in on the sides,and lift up and out.

After replacing the bulb with an appliance

bulb of the same or lower wattage, replace

the light shieldand screws (onsome

models).When replacing the light shield, make sure that the tabs at the back of the

shieldfit into the slots at the backof the

light shield housing. Plugthe refrigerator back in.

bulb of the same or lower wattage, replace

Replace the bulb with an appliance bulb

of the same or lower wattage, and

reinstall the light shield. When reinstalling the light shield, make sure

the top tabs snap securely into place.

Replace the screw (on some models). Reinstall the shelf and plug the

refrigerator back in.

I r I I Display

Dispenser (on some models)

Unplugthe refrigerator.

Thebulb is located on the dispenser under the control panel. Removethe light bulb by turning it counterclockwise.

Refrigerator Compartment (on models with LEDlighting)

Somemodels may have LEDlighting display Ifthis assembly needs to be replaced,call GE on the top and/or sides of the fresh food Serviceat !.800./432.2737in the United States compartment and inthe rear andside of the or !.800.56!.3344 in Canada.

freezer compartment

Replace the bulb with a bulb of the same

size and wattage.

Plug the refrigerator back in.

Trim kits and decorator panels.

GEAppliances.com

For CustomStyle ''_models Read these instructions completely and carefully.

Before You Begin

Some models ore equipped with trim kits that allow you to install door ponds. You con order pre-cut block, white, bisque or stainless steel decorator ponds from GE Ports and Accessories, 800.626.2002, or you con add wood

ponds to match your kitchen cabinets.

Panels less than 1/4" (6 mm) thick

When installing wood panelslessthan 1/4" (6mm) thick, you need to create a filler panel, such as 1/8" cardboard, that will fit between the face of the door and the wood panel.Ifyou are installing the pre-cut decorator panels,pre-cut filler panels are included

in the kit.Thecombined thickness ofthe decorator or wood panel and the filler panel should be !/4" (6mm).

Panels 1/4"thick or less

3/4" (19 mm) or Raised Panel A raised panel design screwed or glued to a 1/4" (6mm) thick backing,or a 3/4" (19mm)routed board can beused.The raised

portion of the panel must befabricated to permit clearances of at least 2" (5.1cm) from the handle sidefor fingertip clearance. Panelsthicker than !/4" (6 mm),upto 3/4" (19 mm) max, will require that the outer 5/16" (8mm)of panel perimeter be no thicker

than !/4" (6mm).

Weight limitations for custom panels. FreshFoodif8 Ibs.(! 7kg) max.

FreezerDoor 28 Ibs.(!5 kg)max.

Panels thicker than 1/4" 16mm)

5/16" (8mm)

1/4" (6ram)max

3/4" (19 mm)

2" (5.1cm) Clearance Handle Side

Panel

1/4" (6mm)

Thick Backing

3/4" (19mm)

Refrigerator Door

Trim kits and decorator panels.

23' Dimensions for Custom Wood Panels

Theareas at the top of the panels needto be cut out of the panels.

FreezerPanel

Without Dispenser

FreezerPanel

With Dispenser

FreshFoodPanel

Cutout--_

5/16"

(8 mm)

I"-" 1/8" (5 mm)

i L

Cutout --_

5/16"

(8 mm:

p- 1/8" (3 mm)

i i

.,I

17YJ'

(45.4 cm)

67%2"

(170.9 cm)

FRONT

4_ !41%_''

(36.8 cm)

FRONT

141%2"..

(36.8 cm)

3P/8"

(85.4 cm)

25' CustomStyle T"Dimensions for Custom Wood Panels Theareas at the top of the panels needto be cut out of the panels.

1/8" (3 mm)-- N

67%2"

(170.9 cm)

FRONT

,_ 191%Z' ..__

(49.5cm)

Cutout

m m

----_ 5/16"

I..,

"-'} (8 mm)

FreezerPanel

Without Dispenser

Cutout--m _- 1/8" (3 mm)

:::: J

5/16"

(8 ram)

69"

(175.3cm)

FRONT

14z%2" _,

"(36.8 cm)

Cutout -_"

5/16"

18 mm)

Freezer Panel

With Dispenser

I"-- 1/8" (3 mm)

17"

(43.2 cm)

FRONT

14_%_'' .

(36.8 cm)

36V4"

(92.0 cm)

FreshFoodPanel

1/8" (3 mm) ,--_I

-i_

69"

(175.3cm)

FRONT

_. 19zsA2'' ___

(49.5 cm)

_- Cutout

----_ 5/16"

"'] (8 mm)

Inserting the door panels.

Read these instructions completely and carefully.

Insert the Freezer Panel and Fresh Food Panel.

Carefully push the freezer panel in until it slides into the slotbehind the door handle. Pushthe filler

panel (requiredwith some door panels/in behind the decorator panel. Repeatfor fresh food panel.

Insert the Bottom Freezer Panel (on dispenser models).

Carefully push the panel in until it slides intothe slot behind the door handle. Pushthe filler panel (required

with some door panels)in behind the decorator panel.

0 Attach the Top Trim on the Freezer and Fresh Food Doors.

TheTopTrim can befound insidethe refrigerator Handtighten only. ivl(]kesurethat the top of each panel compartment, fits snugly behind the lip of the TopTrim.

With a T-20 Torxdriver,attach the Top Trim,using two screws on each Top Trim piece,to the top of each door.

Ifyour model hasa dispenser,this step only applies to

the fresh food panel and top freezer panel.

SideTrim

Cut-Out

SideTrim

Inserting the door panels.

/nsta// the Side Trim.

Thesepiecesare tucked insidethe refrigerator door handle.

Do not remove the protective film on the outside of the Side Trim until the SideTrim is installed.

Fitthe bottom of the SideTrim under the Bottom Trim as illustrated.

Trim

Holdthe SideTrim against the front face of the decorator panelsand fit the SideTrim under the TopTrim.Hake sure

the magnetically attached SideTrim isfitted correctly and that you are satisfied with the appearance of allthe parts.

Bottom Trim

I stall ti

efrigerator

I structi

Questions? Call 800.GE.CARES 1800.432.2737) or Visit our Website at: ge.com

In Canada, call 1.800.561.3344 or Visit our Website at: geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

• IMPORTANT - Sovetheseinstructions

forlocolinspector'suse

•IMPORTANT -Observeollgoverning

codes ond ordinonces

• Note to Installer- Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for future reference.

• Skill level - Installation of this appliance requires

basic mechanical skills.

Models 22, 23, 25, 26, 27 and 29

PREPARATION

WATER SUPPLY TO THE ICE MAKER

If the refrigerator has on ice maker, it will hove to be connected to o cold water line. AGE water

supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at ge.com (in Canada at geappliances.ca) or from Ports and Accessories,

800.626.2002 (in Canada 1.888.261.3055).

TOOLS YOU WILL NEED

• Completion time - Refrigerator Installation

30 minutes Water Line Installation

30 minutes

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed,

remove the base grille {see Step 2 in Moving

the Refrigerator}, then skip to Step 5 in Installing the Refrigerator.

3/8" and 5/16" Socket

1/8" Hex Wrench

Phillips Head Screwdriver

1/2" and 7/16" Wrench

Plastic Putty Knife

Installation Instructions

MOVING THE REFRIGERATOR

I'_ LOADING THE REFRIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until

the refrigerator is in its final location. To move the refrigerator, use a padded hand

truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP,

If the refrigerator must go through

any entrance that is less than 58< wide, the doors must be removed. Proceed

to Step 3.

DO NOT remove the handles. If all entrances are more than 38< wide,

skip to Installing the Refrigerator.

[] DISCONNECT THE WATER COUPLING

(on some modelsl

If the refrigerator has a water dispenser, there is a water line from the cabinet into

the bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

I'_ REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

Bottom

freezer

hinge

Installation Instructions

[_[] DISCONNECT THE POWER COUPLING

(on some models)

If the refrigerator has a water dispenser, there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that

must be disconnected. To disconnect, pull apart at the coupling.

Bottom

freezer

hing_

[] DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses)

from the cabinet into the bottom hinge on the refrigerator door that must be

disconnected. To disconnect, pull apart each connector.

[_ CLOSE THE FREEZER AND

REFRIGERATOR DOORS

i i i i i

i i i i i i i i i i i

[] REMOVE THE FREEZER DOOR

r_ Remove the freezer door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

Remove the two 5/16" or 1/8" hex head screws,

then lift the hinge straight up to free the hinge pin.

S/16" or 1/8" hex head

Bottom refrigerator

hinge

r_ open the freezer door to 90.°

Installation Instructions

MOVING THE REFRIGERATOR ICONT.}

171REMOVE THE FREEZER DOOR (cont.}

rDl As one person slowly lifts the freezer door up

Gnd off the bottom hinge, the second person should corefully guide the woter line ond power line (harness) through the bottom hinge.

90°

[_ Set the door on a non-scratching surface with

the inside up.

[_ REMOVE THE REFRIGERATOR DOOR

rA1 Remove the refrigerotor door top hinge cover

(if equipped) by either squeezing it Gnd pulling it up or by prying it off with a plastic putty knife.

[_] REMOVE THE REFRIGERATOR DOOR

(cont.)

rB1 Remove the two 5/16" or 1/8" hex head screws,

then lift the hinge straight up to free the hinge pin.

5116" or 1/8"hex head

[] Open the refrigerator door to 90.°

i i......i

i_li i

i ....

90 °

Installation Instructions

[_] REMOVE THE REFRIGERATOR DOOR

(cont.)

r_ Lift the refrigerator door up and off the bottom

hinge.

if the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

rg] REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

• When lowering the doors onto the bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure

you insert the tubing all the way to the mark.

L •

Mark

Refreshment Center Models Only

r_ set the door on a non-scratching surface with

the inside up.

• Do not pinch the tubing and harnesses when placing the doors on the bottom hinges.

When connecting the power line and the electrical lines (refreshment center models

only), be sure that the connectors are seated together fully.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 200°F (37°C) because it will not perform properly.

Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing

and electrical connections:

23'/25' 23' B3" wide},

CustomStyle T" 25', 26', 27', 29'

Sides Top

Back

1/8" (4 mm) 1/8" (4 mm)

1" (25 mm) 1" (25 mm)

1/2" (13 mm) 1" (25 mm)

DIMENSIONS AND SPECIFICATIONS

(for 23' CustomStyle T"models)

o o

7( 4" (178.4 cm)

)

(91.4cm)

24" (61_cm)

DIMENSIONS AND SPECIFICATIONS

(for 25' CustomStyle'" models)

DIMENSIONS AND SPECIFICATIONS

Water Electrical

_(19 mm)

Airspace (1/2" [13 mm] Gap

+ 1/4" [6 mm] Wall Plates)

25" (65.5cm) Countertop

24" (61_cm)

"721/j ' (183.5 cm) required for full adjustment

of mobility wheels. If cabinets installed above refrigerator have doors that are flush to the

top of the opening for the refrigerator, then

an additional 1/8" may be required to provide clearance for cabinet doors to open freely.

+ 110 hidden pages