GE PSW26MSTASS, PSW26MSRESS, PSW26MSRDSS, PSW26MSRCKSS, PSW26MSRBSS Owner’s Manual

...

www.GEAppliances.com

Safety Instructions ........... 2-4

°_

Operating Instructions

Automatic Icemaker ........... 12

Care and Cleaning .......... 14, 15

Crispers and Pans ............. 11

Ice and Water Dispenser ........ 13

Refrigerator Doors ............ 10

Replacing tile Light Bulbs ....... 16

Shelves, Bins and Racks ........ 8, 9

Temperature Controls ........... 5

TurboCoot T" . .................. 6

Water Filter ................... 7

Installation Instructions

Installing tile Refrigerator .... 26-29

Moving tile Refrigerator ..... 22-25

Preparing to Install

the Refi_igerator ............... 21

Trim Kits and Panels ........ 17-20

Water Line Installation ...... 30-32

Troubleshooting Tips ....... 33-36

Normal Operating Sounds ...... 33

Models23,25,26,27and29

Profi/eC6te C6te

R6frig&ateurs

La section fran_aise commence a la page 44

Profi/e Lado a Lado

Refrigeradores

La seccidn en espa_ol empieza en la p_gina 82

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 40

Product Reg&tration ........ 37, 38

State of California Water

Treatment Device Certificate ..... 41

Warranty (Canadian) ........... 42

Warranty (U.S.) ............... 43

Write the model and serial

numbers here: Model # Serial #

Find dmse nuInbers (m a label inside the reffigera/or compartment at the

top on the right side.

200D2600POZI3 49-60352-2 12-04JR

IMPORTANTSAFETYINFORMAtiON. READALLINSTRUCtiONS BEFOREUSING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

_This refrigerator must be properly installed

aud located iu accordauce with the lustallalion lnsmmlions before it is umd.

_Do not allow children m climb, stand or haug

oil Ihe shelves in tile refrigerator. They could damage dm refrigerator mid seriously injure

theInselves.

/_2Do not touch tile cold surfaces in Ihe freezer

coInparlmeut when hauds are damp or wet. Skin may slick to them extremely cold surfaces.

_Do not store or um gasoline or olher flmnInable

vapors and liqui&s in die *4cinity of dlis or auy olher appliauce.

_ln refrigeralors wi|h mltoInafic icemaNers,

avoid coutact wilh dm moviug parts of die ejector mechaIfism, or wilh tile heating

demeIlt located oil the t)ottom of tile icemaker. Do not place fiugers or hauds oil dm mlloInafic

iceInaking InechaIfiSnl while ltle refrigera|or is plugged in.

g_Keep fiugers out of tile "pinch point" areas;

clearauces between tile doors aud betweeu tile dours aud catfmet are necessarily small.

Be careful closing doors when children are in file area.

NUnplug tile refrigerator before cleauing aud

Inaking repairs.

NOTE: We strongly recommendthatany servicingbe performedbya quahfied indlviduaL

g_Setling either or txnh comrols to 0 (Off)does not

remove Ix)wet to lhe light circuil.

_Do nol refreeze frozen fouds which have

thawed coInpletely.

www.GEAppliances.com

A DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

Child entrapment and suffocation are IlOt problems of dm past.Junked or ahandoned refrigerators are

still dangerous...even if dmy will sit fbr 'lust a few daw" If you are gelling rid of your old refrigerator,

please fbllow tile instructions below m help prevent accidents.

Before You ThrowAway Your Old Refrigerator or Freezer.

N'Fake off die doors.

}_Leave Ihe shelves in place so that children may

not easily climb inside.

Refrigeren_

All refrigeration products conlain reffigermns, which under federal law must be removed prior

m product disposal. If you are getting rid of an old refrigeration product, check with tile

company handling the disposal about what 1() do.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, if you most use an exlension cord, it is absolulely neces_ry lhal it be a UL-listed (in Ihe UIfiled S ares) or a (_A-hsted (m Canada), 3-wire grounding type appliance extension cord having a grounding

1ype plug and outlet and that die electrical rating of dm cord be 15 mnperes (minimmn) and 120 volks.

IMPORTANTSAFETYINFORMAtiON. READALLINSTRUCtiONS BEFOREUSING.

A WARNING!

HOWTOCONNECTELECTRICITY

Be not, under any circumstances, cut or remove the third (ground) prong from the power cord. Forpersonal safety, this appliance must be properly grounded.

"I]m power coM of this appliance is equipped with a "_-prong (grounding) plug whirl1 mates with

a standard %prong (grounding) wall outlet m minimize the possibilily of electric shock hazard

fi_om tiffs appliance.

Have ltle wall Buffet and circuit checked by a qualified eleclrician to make sure lhe Buffet

is properly grounded. If fire outlet is a standard 2-prong Buffet, it is

y_ur personal reslxmsibility and obligation m have it replaced with a properly grounded

3-prong wall oudet. "I]le refrigerator should always be plugged into

iks own individual eleclrical oullel which has a voltage rating Ihat Inatches lhe rating plate.

This provides the best pertbrmance and also prevenks overloading house wiring circuils which

could cause a fire hazard fi'oIn overheated _vires.

Never unplug your reffigeralor by pulling on ltle power cord. Always grip plug firmly and pull

slraight out from dm outlet. Repair or replace immediately all power cords thai

have become flayed or otherwise damaged. Do not use a cord that shows cracks or abrasion dmnage

along its length or al either end. _heIl Inoving Ihe refrigerator away from lhe

wall, he carefifl not to roll over or damage lt_e [x_wer cord.

USEOFADAPTERPLUGS(Adapterplugsnotpermitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

However, if you must use m_ adapter, where local codes permit, a temporary connection may be made

m a properly grounded 2-prong wall Bullet by use ofa UL-listed adapter available a/most local

hardware slores.

The larger slot in the adapter Inust be aligned with the larger slol in the wall outlet to provide proper

polarity in 1he connection of the power cord.

When disconnecting the power cord froIn the adapter, always hold the adapter in place wilh one

hand while pulling the lx)wer cord plug with the other hand. If this is not done, the adapter ground

terminal is very likely m break with repeated use.

If the adapter ground temfinal breaks, DONOT

USEIhe refrigerator until a proper ground has

been established.

Attaching the adapter ground terminal to a waft outlet

coverscrew does not ground the appliance unless the coverscrew is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to

makesure the outlet is properly grounded.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCtiONS

Aboutthetemperaturecontrols, www.GEAppliances.com

The temperature controls are preset in the factory at 5 for both the refrigerator and freezer compartments. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

Several adjustments may be required. Each time you adjust controls, allow 24 hours for the refrigerator to reach the setting you have selected.

Setting either or both controls to 0 stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating conditions and may require more than one adjustment.

I f

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation,

remove it now.

PerformanceAirFlowSystem

Tile Perfbnnance ;Mr How System is designed to Ina_mfize temperature conlrol in lhe refl-igeralor and freezer coInpartmenls. This unique special featore consists of lhe ;Mr Tower Mong the [rack wall of tile

refrigerator and Ihe Air Tunnel on tile bollx_In porlion of the freezer rear wall. Placing food in f_ont of the louvers oil these coInponenls will not affect perfbnnance. ;Mlhoogh tile Air Tower and the Air Tunnel can

be removed, doing so will affect temperature perfk_rmance. (For removal instructions, on-line, 94 hours a day, contact us at GEAppliances.com or call 800.GE.CARES. In Canada, contact us a/www.geappliances.ca

or call 1.800.361.3400.)

About TurboCooL"

How it Works

TurboCoof rapidly cools Ihe refrlgeralor

coInparunent in order m more quickly

cool food_s. Use Tu_oCool when adding a large alllotlIlt of food to die refrigerator

coInparunent, putling away foods after they have been sitling out al rooIn teInperature

or when pulting away warIn leftovers. It can also be used if tile refrigerator has been

wilhout power for ml extended period. Once activated, die compressor will mrn on

imznediately and the fhns will cycle on and offat high speed as needed for eight hours.

Tile compressor will conlilllle |O rUll until lhe refrlgera|or coInpartment cools to

approximately 34°F (I°C), then it will cycle on and off m maintain |his setting. After

8 hours, or if TtldloCoo! is pressed again, lhe refrigerator coInpartment will re|urn

to tile original se||ing.

How to Use

Press TurboCool.Tile refrigerator |emperamre display will show rc.

After TurboCooliscomplete, the refrigerator comlyartinent will remm m die origdnal

setdng.

NOTES."

Therefrigerator temperaturecannotbe changed

during Tu_oCool.

Thefreezertemperatureis not affected during

TurboCool

Whenopening the refrigerator doorduring TurboCool,the fans will continue to run if they

havecycledon.

AboutClimateKeeper2:"

How # Works

Tile new ClimateKeeper2TM is tile industry's most advanced refrigeration system,

delivering optimum temperature and humidily perfbnnmtee to keep food fresh

longer and reduce freezer burn, while mainl_ining E s_-level efficiency.

Tile new ClimateKeeper2 system features two evaporator_-4.me for tile refi_igerator

and one for tile freezer.

This provides two selrarate cooling systems ff)r tile entire unit, and separates tile

airflow between Ihe fresh flood and freezer _cdons during normal cooling opera|ions.*

This ensures thai die humidily levels in die fresh food secdon are significantly higher

lhan in a conventional system,** allowing fresh produce mid olher unsealed foods to

retain Iheir Inoismre content and freshness longer. Moisture _nsilive fbocks such as

fresh fruil, sala&s, rice, era., can now be stored Oil open shelves wilhout excessive

mois|ure loss.

"I]le separate airflow system miniInizes |he Inixing of air between die I_vo

COillIyarLIllelllS , which reduces odor

|ransfer, resulting in improved laste of ice.

"I]le ClimatoKeeper2system also reduces the nuInher of defrosting cycles in the

fi'eezer evaporalor, thereby improving the |emperature mainlained in |tie freezer and

reducing freezer burn.

*Freezerair is usedin the CustomCoolfeature. **Testingshowsa higher level of humidiZyin

the FreshFoodsection in ClimateKeeper2 refrigeratorsversusconventionalunits.

Aboutthe water filter.(onsomemodels) wwvc.GEApplianees.eom

On some models

Place the top of the cartridge up inside the cartridge holder and

slowly turn it to the righL

Water Filter Cartridge

Tile water filter cartridge is located in the hack upper right corner of 1tie refrigerator

coInpartment.

When to Replace the Filter

There is a replacement indicator light for lhe water filter cartridge oil tile dispenser.

This light will turn orange m tell you dial you need m replace tile fiher soon.

Tile filter cartridge should be replaced when tile replacement indicator light rams

red or iftile flow of water m 1tie dispenmr or icemaker decreases.

Installing the Filter Cartridge

O lfyou are replacing tile cartridge, first

remove tile old one by slowly turning it to the left. Oe net pull down oil tile cartridge. A small amount of water

may drip doval.

O Fill file replacement cartridge with

water from file tap to allow for trotter flow fi'om the dispenser immediately after installation.

Lining up the arrow oil die cartridge and die cartridge holder, place the

mp of the new cartridge up inside

tile holder. Denetpush itup film

tile holder.

O Run water fi'om the dispenser fi)r

3 Ininules (about one and a half

gallons) to clear lhe system and prevent sputtering.

Press and hold the RESET WATER FILTER

pad oil the dispenser for 3 seconds.

NOTE: A newly-installed water filler cartridge may cause water tospurt f:com ltle dispenser.

Filter Bypass Plug

You ImlSl use tile filter bypass plug

when a replacement filler carlridge is not availahle. The dispenser and the icemaker will not operate wifllOUt file filter or filter

bypass plug.

Replacement Filters:

Toorder additional filter cartridges

in the United States, visit our Website,

wwvc.GEAppliances.eom, or caR GE Parts

and Accessories, 800.6262002.

G_T Suggested Retail $34.95 USD

CustoIners in Canada should consult ltle yellow lrages for ltle nearest Camco

Service Center.

Slowly mm it to the right until lhe filter cartridge stops. DONOT OVERTIGHTEN.

;'ksyou turn the cartridge, it will automatically raise it_self into position.

Czartridge will rotate about 1/4 turn.

Abouttheshelves,binsand racks.

Not all features are on all models.

Refrigerator Door Bins and Freezer Door flit-Out Bins

Large Bins

Tile larger reffigeralor door bins mid freezer tilt-out door bins are adjostable.

Teremove:Lifl tile front of die bin straight

up, dzen lift lip mid ouL

Refrigerator bin

Freezer tiff-out bin

Toreplace or relocate: Engage tile back side

of tile bin iIl the molded supports of dm door. "I]len push down oil die front of file

bin. Bin will lock in place.

SmaflBms

Toremove:Lifl tile front offlle bin straight

up lhen oul.

Toreplace: Position file bin above die

reclangular molded support_s oil ltle door. Then slide tile bin down on|o tile support

to lock it in place.

The snugger helps prevent tipping, spilling

or sliding of small ilems sit)red on tile door shel£ Place a finger oil either side of tile

snu_4er near tile rear and Inove it back mid fbrth to fit your nee(is.

careful hen lacth

Make sure that items do not block

or fall into the ice chute.

Door Wine/Beverage Rack (on some models)

This rack holds up t,o 5 cans, one Ix)tile of wine or one 2-liler bottle of soda.

The rack hangs ]_:(oIll|he sides of the dairy bin.

TOremove:

Empty tile wine/heverage rack.

_ Holding Ihe botlom of tile dairy bin,

lift die front straight up, dmn lift up and oul.

_'lb delach Ihe rack f_om Ihe dairy bin,

pull tile rack's side wires out of tile holes on each side of tile dairy bin.

Toreplace:

_ Reattach tile rack to dm sides

of tile bin.

Engage the back side of the bin in die molded supports oil Ihe door.

Then push down on tile front of die

bin. The bin will lock into place.

Presstab and pull sheff forward to remove

www.GEAppliances.com

Sfide-Out Spillproof Shelf

Tile slide-out spillproof sheff allows you to reach items stored behind ()tilers. The

special edges are designed to help prevent spills from dripping to lower shelves.

Toremove:

Slide the shelf out until it reaches tile stop, then press down o11 tile tab and slide tim

sheff straight out.

Toreplace or relocate:

Line tile shelf up with the supports and slide it into place. The shelf cml be

repositioned when tile door is at 90 ° or more. "Ib reposifion tile shelf; slide lhe shelf

vast tile stops and angle downward. Slide sheffdown m the desired position, line up

with the supports and slide into place.

Makesureyoupush theshelvesaftthe wayback in beforeyouclosethedoo_

QuickSpace" Shelf

This sheff splits in half and slides under ilself for storage of tall items on tile shelf

below. This sheff can be removed mid replaced

or relocated just like Slide4)ut Spillproof Shelves.

TOremove, slide out to tile stop l_sifion,

lift tile fi'ont past the stop position, and slide out.

Freezer Baskets

On _Ine models, tile dill extension basket can be removed by pushing Ihe basket all

Slide-OutFreezerShelves

To remove, slide out m lhe stop position,

lift tile front past tim stop position, and slide out.

On some models, lifts shelf cml IlOtbe used in dm lowest lu_sifion.

the way m tile back oflhe freezer. Lift tip until file back pins are disengaged. Lift tile

entire basket up and pull out.

Make sureyou push the baskets all the way back in before you close the doo_

Make sureyou push the shelves aft the way back in before you close the doo_

Fixed Freezer Shelves

Toremove,lift the shelf up at tim lefi side

and titan bring tim shelf out.

NOTE FORDISPENSERMODELS: Inorder m take hill advaIwage of tile till_ut ice bin,

oIfly store items on tile shelf below the ice bin thai are IlO taller lhan 1he lowest point

Oil |he biIl.

Abouttherefrigeratordoors.

Refrigerator Doors

The refrigerator doors may feel different lhan Ihe ones you are used Io. The special door opening/closing feature makes stare

lhe doors clo_ all ltle way and are securely sealed.

When opening and closing Ihe door you will notice a stop position. If the door is

opened past this stop poinl, Ihe door will remain opera to allow you to load and

uIfload food more easily. When the door is only partially opera, it will automatically close.

When the door is only partially open,

it willautomaticallyclose. Beyondthisstopthedoorwil! stayopen.

The resistance you fkel at die stop position will be reduced as the door

is loaded wifll food.

\\\ //

Door Alignment

1f doors are uneven, adjust file refrigerator door.

• r "PP

Using a 7/16 wrench, turn Ihe door adjusting screw to tile fight to r,_i_ tile

door, lo tile left to lower it. (A nylon plug, imbedded ill tile Ihreads of tile pin, prevenLs the pin from turning

unless a wrench is used.)

After o[le or two turns of fl_e wrench, open and clo_ Ihe refligerator door

and check die alignment at the mp of the doors.

Aboutthecrispersandpans. eEAppliaaoescem

Not all features are on all models.

Fruit and Vegetable Crispers

Excess waler tha! may accumulate in the bo/toIll of lhe drawers should be wiped dry.

On some models, tile bolR)nl drawer ha.s full exlension slides ltza/allow thll access

to tile drawer.

HI _ LO

Adjustable Humidity Crispers

Slide lhe control all tile way to tile HI rotting to provide high humidity

recoImnended for most vegetables.

Convertible Deli Pan

iii_) ¸¸ g )j

The converfihle deli pan has its own cold air duct to allow a stremn of cold air from

tile freezer compartment to flow to the pan.

The variable temperature control regulates

tile airflow from tim Climate Keeper.

Aboutcrisperremoval

Not all features are on all models.

Crisper Removal

The top crispers caa_ easily be removed by pulling the drawer straight out and lifting

the drawer up and over lhe stop location.

If file door prevents you fi'oIn taking oot the drawers, first Iry to remove tile door bins. If this does not of]Terenough

clearance, Ihe refiigeramr will need m be rolled forward until lhe door opens

enough to slide tile drawers out. In some ca.ms, when you roll lhe refiigerator out

you will need Io move tile refi'igera/or m file left or fight as you roll it ouL

Slide tile control all lhe way to the LOselting to provide lower humidity

levels recommended for most fmils.

Set tile control to the eoldeMmtfing to store flesh meals.

Set the comrol to coldto convert the pan lo normal refrigerator lemperatore and

provide extra vegetahle storage space. The cold air duct is mined off Variahle mtfings

belween them extremes cml be mleoed.

Toreplace the bottom crisper:

Make sure all foor swing lock_ are in

lhe unlock position.

Place the sides of tile drawer into the

drawer suplx)rts, making sure tile swing

locks fit on the drawer slols.

Lock all fimr swing locks hy rotating

lhem to Ihe lock position.

Toremove the bottomcrisper.

Pull the drawer out m tile stop fu_smon. Rotate all fimr swing lo('k_ to tile tmlock

position.

LiR tile f_ont of file drawer up and out.

Abouttheautomaticicemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

On dispenser models, to Automatic Icemaker access ice or reach the

power switch:

The icemaker will produce _ven cubes

per cyvle--apwoximalely 100-130 cubes in a 24-hour period, depending on freezer

coInparlment temperature, rooill temperature, number of door openings

and other use conditions. If tile refrigerator is operated betbre tile

water COIlnectioIl is made to tile icemaker,

set file power switch in tile 0 (off] position.

_¢VtleIltile refrigerator has been connected

u) tile water supply, set tile ix)wet switch to

o Lift the bin, then pull it

forward until the bin stops.

tile I (on) position.

Tile icemaker will fill witil water when it

cools to 15°F (-10°(;). A newly installed refrigerator may take 12 to 24 hours to begin

making ice cul_.

You will hear a buzzing sound each time

ltle icemaker fills with water.

Throw a_ay the first few batches of ice to

allow tile water line Ix) clear. Be sure nothing interfieres with 1tie sweep

O Lower the bin to access ice

or reach the power switch.

NOTE"In ordertotakefulladvantage of thetilt-outicebin, only storeitems ontheshelfbelowtheice binthat arenotallerthanthelowestpoint onthebin.

of tile feeler ann.

_Then tile bin fills to tile level of tile fi_eler

arm, tile icemaker will stop pro&icing ice. It is normal for several cubes to be

joined together.

If ice is not u_d frequently, old ice cubes

will become cloudy, taste stale and shrink.

Special notes about dispenser models:

/;)_Dispenser Inodels have a tih-out ice bin.

The bin can be tilled out as shown in

tile illustrations, and it will hold ilseff up while ylm take ice out or mm the icemaker power switch on and off"

Be sure m put tile bin back in place befbre closing tile &)or.

@ To restore your ice level from an empty

bucket stage, the following steps are

recommended:

12 hours after tile first batch of ice has fMlen inlo tile bin, dispense

3 to 4 cubes.

After an additional 6 hours, dispense

3 to 4 cubes again.

These steps will restore your ice level in tile shortest amount of time.

i_i}!;¸{_ii_ _ ;ii;{{¸i! !}!ii} }i ¸{i }!{__)}:iil;iii

NOTE.."Inhomeswith lower-than-averagewater pressure,you may hearthe icemaker cyclemultiple

tines when maklhgone batchof ice.

Lift the bin, then pull it

_ forward until the bin stops,

Lift andpul! forward again

_ to remove the bin.

Removing Ice Bin (dispenser models)

CAUTION: The ice bin is heavy when full

Set die power swi/ch to tile 0 (Off)position

befbre removing die biIl.

When replacing the bin, be sure to press it

firmly into place, flit does not go all tile way back, relnove it and rotate Ihe drive mechanism 1/4 ram. Then push tile bin back again.

Dispenser Models only

Abouttheice and water dispenser.(onsomemodels) wwvc.GEAppliances.com

On some models

TOUse the Dispenser

SpillShelf

Select CUBEDICE _, CRUSHEDICE I_j or WATER_L

Press tile glass gently against tile mp of tile dispenser cradle.

Tile spill shelf is not selgdraining. To reduce water spo/fing, the shelf and its

grille should be cleaned regularly.

If no water is dispensed when the refrigerator is

first installed, there may be air in the water line

system. Press the dispenser arm for at least two minutes to remove trapped air from the water

line and to fill the water system. Toflush out impunties in the water line, throw away the first

six glassfuls of wate_ CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

Locking the Dispenser

Press 1DieLOCKCONTROL pad for 3 seconds m

lock the dispenser aaM contrul panel. "Ib

unlock, press and

hold tile vad again

for 3 seconds.

Dispenser Light

QuickIce

DoorAlann

This pad rams the night

lightin die dispenser on

and offl The ligDltal_) comes o[1 when tile

dispenser cradle is pressed. If fills light

bums uul, it should be replaced wilh a 6 watt

12 V maximum bulb.

When you need ice in a hurry, press lifts

pad m speed up ice pro&lction. This will

increa_se ice production for Ihe DbllowiIlg

48 hours or until you press tile gad again.

To set the alarm, press lifts pad until tim indicator light comes

on. This alarm will sound if either door is

open for Inure Ihan 3 minutes. "Ille ligDlt

goes out and file beeping stops when

you close file door.

Important Facts About YourDispenser

/;5_Do not add ice from Irays or [rags m

1Diestorage drawer. It may not crush or dispense well.

N Avoid overfilfing glass widl ice and use

of narrow glasses, l_acked-up ice cwa jaan lbe chute or cause lhe door in the chule

to freeze shuL If ice is blocking file chute, poke it IDlrough wi|Dl a wuoden

spoon.

@ Beverages aaM foods should not be

quick-chilled in IDle ice storage drawer. Cans, bottles or Dood packages in IDle

slorage drawer may cause |Die icemaker or auger mjmn.

@To keep dispensed ice from missing

ltle glass, put tile glass close m, but not touching, file dispenser opening.

N Some crashed ice may be dispensed even

fllougb you selected CUBED ICE.This happens occasionally when a few cubes

accidentally get directed m tile crusher.

NAfter crashed ice is dispensed, some

waler may drip Di'olll tile chine.

}_Sometimes a small mound of snow will

Di)rln()I1tile door in 1be ice chule. This condition is normal and usually Occurs

when you have dispensed crushed ice repeatedly. Tile snow will eventually

ex_lx) rate.

Careandcleaning of therefrigerator.

Cleaning the Outside

Dispenser drip area,

The dispeoser drip area, (on mine models)

beneatll tile grille, should he wiped dry. Water left in this area may leave deposils. Remove

file deposits hy adding undiluted \_Ilegar 10 tile well. Soak until tile deposils disappear

or become loose enough to rinse away.

The dispeoserersdle (on some models).

Before cleaning, lock tile dispenser by pressing and holding die LOCK CON_OL

vad for 3 seconds. Clean witiz warm waler and baking soda _flulion_about

a tablespoon (15 Inl) oflxaldng ,soda to a quart (1 liler) of water. Rinse thoroughly

and wipe dry.

The door handles and trim. Clean with

a clo/h dampened with soapy water. Dry witil a soft clotil.

Thestainlesssteelpanelsanddoorhandles

(on some models) cml he cleaned with a

commercially available stainless steel cleaner such as Stainle,_ SteelMc_,@Y"

StainN,:s,SteelM_: is available al Ace, "Into Vahm, Servistar, HW1 and other leading

stores. It is also m_lahle through GE Paris aim Accessories, 800.626.2002. Order Dart

Immber V,_X10X15.

Do not use applimlce wax or polish on die stainless sled.

Keep the outside clean. Wipe witil a clean cloth lighdy dmnpened with kilchen

appliance wax or tnild liquid dish detergem. Dry and polish wilh a dean, soft clodl.

Do not wipe the refrigerator with a soiled dish cloth or wet towel Thesemay leave a residue

that can erode the paint Do not use scouring

pads, powdered cleaners, bleach or cleaners containing bleach because theseproducts can

scratch and weaken the paint finish.

Cleaning the Inside

Tohelp prevent odors,leave an open hox of

baking mda in tim fresh food aim freezer compar tmen ks.

Unplug the refrigerator before cleaning. If dfis is not practical, wring excess moisture out

of sponge or cloth when cleaning around switches, lights or controls.

Use warm waler and baking soda mlufion-

about a lablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans

and neutralizes odors. Rinse and wipe dry.

Useof any cleaning solution other than that which is recommended, especially those that

contain petroleum distillates, can crack or damage the interior of the refrigerator,

Avoidcleaningcoldglassshelveswithhot water becausetheextremetemperaturedifference

maycausethemto break.Handleglassshelves carefully4Bumpingtemperedglasscancause

it to shatter.

Donotwashany plasticrefrigeratorpartsin

thedishwashec

Behind the Refrigerator

www.GEAppliances.com

Be carefill wheu Ino_fing file refrigerator away from the wall. All types of floor

coveriugs cml be damaged, particularly cushioued coveriugs aud tho_ wilh embossed surfaces.

Pull lhe refrigerator straight out aud return it m position by pushing it straight iu.

Moving Ihe refi'igeramr in a side direction may result in dmnage m ltle floor covering or refrigerator.

Preparing for Vacation

For long vacations or absences, reInove food aud unplug Ihe refrigerator. Clean file interior with a baking soda solution

of one tablespoon (15 ml) of/fairing soda m one quart (1 li/er) of water. Leave lhe

doors open. Set the icemaker lx_wer switch m the

0 (off) position aud shut off' file wa_er supply

m ltze refrigerator.

When pushing the refrigerator hack, make sure

you don't roll over the power cordor icemaker supply line (on some models).

Ifdie temperature cau drop below freezing, have a qualified servicer drainfile water supply sy_lem (oil _me models) to prevent

serious properly damage due m flooding.

Preparing to Move

Secure all loose items such asshelves mid drawers hy taping them _curely in place

m prevent damage.

When usiug a haud Iruck to move the

refrigerator, do uol rest the fl'ont or back of lhe refrigerator agminst the haud truck.

This could dmnage tile refl'igerator. Haudle only froIn ltle sides of file refrigeralx_r.

Besuretherefrigeratorstays in an up@t positionduringmoving.

Replacingthelight bulbs.

Setting the controls to OFFdoes not remove power to the light circuit.

Refrigerator Compartment--Upper Light

Tabs

O Unplug tile refifigerator.

The bulbs are located al tile lop of die compartmenl, inside file light shield.

Oil some models, a screw a/tile front of tile light shield will have m be removed.

To remove Ihe light shield, on some

models, press in o11 the tabs Oil the

sides of tile shield and slide fbrward and oul. Oil other Inodels,just slide

fi)rward and out.

Refrigerator Compartment--Lower Light

Thislightis located above the top drawe_

Unplug file refiigevamr.

O ReInove the convertible meat drawer

comrol knob by pulling straight out.

Lift file light shield up and pull it out.

Freezer Compartment

After replacing 1tie bulb with an

appliance bulb of the stone or lower

wallage, replace the light shield and

_-rews (on some Inodels). When replacing the light shield, make sure

flint the tabs al the back oflhe shield fit imo the sloks at file [rack of the light

shield housing.

Plug the refi*igerator back in.

After replacing 1tie bulb with an

appliance bulb of the stone or lower

waltage, replace the shield and

die knob.

Plug the refifigerator back in.

Unplug file refiigeramr.

O ReInove the shelf just above tile light

shield. (The shelf:will be easier to

remove if it is emplied first.) On some Inodels, a screw al the top of the light

shield will need m be removed.

To remove Ihe light shield, press in on the sides, mid lift up and out.

Dispenser (on some models)

Unplug the refiigerator.

O "Itie bulb is located on the dispenser

under lhe conlrol panel.

Remove the light bulb by turning

it counterclockwise.

_ Replace the bulb wilh an appliance

bulb of the stone or lower wattage, and reinstall the light shield. When

reinstalling the light shield, make sure the mp tabs snap securely

into place. Replace 1tie screw (on some models).

_ Reinstall the shelf and plug the

refi*igerator back in.

Replace the bulb with a bulb of the same size and wattage.

Plug the refifigerator back in.

Trimkits and decoratorpanels.

For CustomStyle TM models

Read these instructions completely and carefully.

Before YouBegin

Some models are equipped with trim kits that allow you to install door panels. Youcan order

pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,

800.626.2002, or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4" (6 mm) thick

When installing wood panels less than 1/4" (6 ram) thick, you need to create a filler Irmlel, sudl as 1/8"

(3 ram) cardboard, that will fit belween die face of the door and tile wood vanel. If you are inslMling die pre-cut decoralor panels, pre-cut filler irmlels are included in tile kit. The combined ltlickne_s of tile decoralx)r or wood panel and tile filler lmnel should be 1/4" (6 iron).

Panels II4" (6 mm)thick or less

/4"(6 ram)Max,

3/4" (19 mm) or Raised Panel

A raised panel desigm _'rewed or glued to a 1/4" (6 InIn) thick backing, or a 3/4" (19 ram) routed board can be used. Tile raised portion of the panel Inust be fabricated to permit clearances of at least 2 ' (5.1 cm)

from 1tie fimldle side fi_r fingertip clearance.

Panels Ihicker than 1/4" (6 ram), tip m 3/4" (19 • . • r. -,ram) maxmmm, wall reqmre that lhe outer :)/16

(8 Iron) of pmlel perimeter be no thicker tfian 1/4" (6 ram).

Weight limitations for custom panels: Fresh Food 38 Ibs. (17kg) max.

Freezer Ooor 28 Ibs. (13 kg) max.

Panelsthickerthan1/4"{6rnm)

2"(51 cm} Clearance

HandleSide

1/4" (6ram}

ThickBacking

4 16ram) Max.

3/4"(19ram)

Appeamnce Panel

{19ram)

Door

Trimkits and decoratorpanels.

23" Dimensions for Custom Wood Panels

The area__at die lop of 1tie panels need to be cut out of tile t_mlels.

FreezerPanel FreezerPanel

WithoutDispenser WithDispenser

FreshFoodPanel

Cutout--_,, I'*- 1/8" (3 ram}

_ ''

___11

5/t6"

{8mm)

67%2"

(1709cm)

FRONT

/36.8cm/

25" CustomStyle _ Dimensions for Custom Wood Panels

Cutout"-_I _- 1/8" (3mm}

____I I

5/16"

(8 mm)

17½"

{45.4cm)

FRONT

• t4%Z' _j (368 cm)

33%"

1854cm)

{

1/8" {3 mm)--_; i_- Cutout

',',___}5/I6"

--{ 18ram)

67%Z'

(170.3cm)

FRONT

i- 191%z"

(43.5crn)---_

The area-_ at file top of 1tie panels need to be cut out of the panels.

FreezerPanel

WithoutDispenser

Cutout--_i I_- 1/8" (3mm}

i i

FreezerPanel

With Dispenser

5/16"

(8mm)

69"

(1753crn}

FRONT

/3tL_cm)

(Smm}

1 RiNT

W%Z' _.

(368 cm)

36V4"

{920 cm)

Fresh FoodPanel

1/8"{3mm)--_

I"- Cutout

',___}5/i6"

63 "r

(1753cm)

FRONT

(49.bcm)

---{ 18ram)

Insertingthe doorpanels.

Read these instructions completely and carefully.

O Insert the Freezer Panel and Fresh Food Panel.

Careflllly push tile freezer vanel in until it slides inlo tile slot behind die door handle. Push dle filler

vanel (required wilh some door pmlels) in behind file decorator panel. Repeat for fresh food vanel.

Insert the Bottom Freezer Panel (on dispenser models).

Careflflly push the pmlel in until it slides into the (required with some door pmlels) in hehind the slot behind tile door handle. Push tile filler panel decorator panel.

0 Attach the Top Trimon the Freezer and Fresh Food Doors.

The "Ibp Trim can be found inside the refrigerator

fiOilllYartinell/.

Wilh a T-20 ]brxdriver, al_ach Ihe Top "IHm, using _wo screws on each Top Trim piece, m tile mp of

If y_ur model has a dispen_r, this slep only applies m tile fresh food panel and top freezer panel.

each door. Hand fighlen only. Make sure thai the

top of each panel fits sImgly behind the lip of the

"Ibp Trim.

Trim Screws

Cut-Out

SideTrim

Insertingthe doorpanels.

O Install the Side Trim.

These pieces are tucked inside tile refi_igerator door handle.

Donot removetheprotectivefilm onthe outsideof the SideTnmuntil the SideTnmJsinstalled.

Fit tile bottom of tile Side Trim under die Buttom Trim as illus_rated.

Hold the Side "IYim against the front face of tile decorator panels and fit the Side "Ii'iIn under die "Ibp "IHm. Make stare die magnetically attached

Nde Trim is fitted correclly mad that you are satisfied wilh die appearm]ce of all die parLs.

Installation

Refrigerator

Instructions

I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

• Proper installation is the responsibility of

the installer.

• Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in Installing the Refrigerator.

In Canada, call 1.800.361.3400 or Visit our Website at: geappliances.ca

30 minutes

Water Line Installation

30 minutes

Models 23, 25, 26, 27 & 29

PREPARATION

WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. AGE water supply kit (containing tubing, shutoff

valve, fittings and instructions) is available at extra cost from your dealer, by visiting our

Website at GEAppliances.com (in Canada at geappliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada

1.888.261.3055).

TOOLS YOU WILL NEED

3/8" and 5/16" Socket

1/8" Hex Wrench

1/2" and 7/16" Wrench

Plastic Putt,/Knlfe

Phillips Head Screwdriver

Installation Instructions

MOVING THE REFRIGERATOR

[] LOADING THE RERIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors until the refrigerator is in its final location.

To move the refrigerator, use a padded

hand truck. Center the refrigerator on the hand truck and secure the strap around

the refrigerator. DO NOT OVERTIGHTEN THE STRAR

If the refrigerator must go through

any entrance that is less than 38" wide, the doors must be removed.

Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than

38" wide, skip to Installing

the Refrigerator.

[] DISCONNECT THE WATER

COUPLING (on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into

the bottom hinge on the freezer door that

must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White cotlar

[] REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

Bottom

freezer

hinge

Installation Instructions

[] DISCONNECT THE POWER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the

cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect pull apart at the coupling.

iiiiiii!ii

4"¸¸¸¸¸¸

freezer / _ J L___t,..-.---_ /

h,o e

[] DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

[] CLOSE THE FREEZER AND

REFRIGERATOR DOORS

[] REMOVE THE FREEZER DOOR

[] Remove the freezer door top hinge cover

(if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

If the refrigerator has a refreshment center, there are electrical connectors

(harnesses) from the cabinet into the bottom hinge on the refrigerator door

that must be disconnected.

To disconnect, pull apart each connector.

Bottom

refrigerator hinge

[] Remove the two 5/16" or 1/8" hex head

screws, then lift the hinge straight up to

free the hinge pin.

5/16" or 1/8" hex head

[] Open the freezer door to 90.°

90°

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

[] REMOVE THE FREEZER DOOR

(cont.)

[] As one person slowly lifts the freezer door

up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90°

[] Set the door on a non-scratching surface

with the inside up.

[] REMOVE THE REFRIGERATOR

DOOR (cont.)

[] Remove the two 5/16" or 1/8" hex head

screws, then lift the hinge straight up to free the hinge pin.

5/16" or 1/8" hex head

[] Open the refrigerator door to 90.°

[] REMOVE THE REFRIGERATOR

DOOR

[] Remove the refrigerator door top hinge

cover (if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

90°

Installation Instructions

[] REMOVE THE

REFRIGERATOR DOOR (cont.)

[] Lift the refrigerator door up and off the

bottom hinge.

If the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the

bottom hinge.

90 °

[] REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

" When lowering the doors onto the

bottom hinges, make sure the second

person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure you insert the tubing all the way

to the mark.

Refreshment Center Models only

[] Set the door on a non-scratching surface

with the inside up.

Mark

• Do not pinch the tubing and harnesses

when placing the doors on the bottom

hinges.

• When connecting the power line and

the electrical lines (refreshment center

models only), be sure that the connectors are seated together fully.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C)

because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100°F (37°C)

because it will not perform properly.

• Install it on a floor strong enough to

support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and

plumbing and electrical connections:

23' (33" wide),

23'/25" CustomStyle TM 25", 26", 27", 29"

Sides 1/8" (4 mm) 1/8" (4 mm) Top 1" (25 mm) 1" (25 mm)

Back 1/2" (13 mm) 1" (25 mm)

DIMENSIONS AND SPECIFICATIONS (for 23' CustomStyle TM models)

70_"(178 4cm)

36"_

DIMENSIONS AND SPECIFICATIONS (for 25' CustomStyle TM models)

DIMENSIONS AND SPECIFICATIONS

Electrical

24"(61 cm) 5cm)

+i':1_ ++++

' J'L

72¼"{1835cm)+

"72+/4 " (183.5 cm) required for full adjustment

of mobility wheels. If cabinets installed above refrigerator have doors that are flush to the top of the opening for the

refrigerator, then an additional 1/8" may be required to provide clearance for cabinet

doors to open freely.

Installation Instructions

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one.

See "Installing the Water Line" section.

NOTES:

• Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall

outlet.

• If your refrigerator does not have a

water filter, we recommend installing

one if your water supply has sand or particles that could clog the screen of

the refrigerator's water valve. Install it

in the water line near the refrigerator. If using GE SmartConnect TM Refrigerator

Tubing Kit, you will need an additional tube (WX08XlO002) to connect the filter.

Do not cut plastic tube to install filter.

[] If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto the end of the tubing coming from the

house cold water supply.

If you are using the GE SmartConnect TM tubing, the nuts are already assembled to the tubing.

[] If you are using copper tubing, insert

the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect TM tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

[] Fasten the tubing into the clamp provided

to hold it in position. You may need to pry open the clamp.

Tubing Clamp

1/4"

Compression Nu

Ferrule _ (sleeve)

Refrigerator

Connection

SmartConnect 'MTubing

1/4" Tubir

[] TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve

(house water supply) and check for

any leaks.

[] PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make

sure the icemaker power switch is set to the O (off) position.

See the grounding information attached

to the power cord.

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

[] PUT THE REFRIGERATOR

IN PLACE

Move the refrigerator to its final location.

[] LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the

bottom hinges.

[] LEVEL THE REFRIGERATOR

(cont.)

To adjust the ) I II rollers on 23"/25'

CustomStyle TM

models:

adjusting screws

Turn the front roller __@ _ F clockwise to raise

the refrigerator, Roller adjusting screws

counterclockwise to lower it. Use a 3/8" hex wrench with

extension, or an adjustable wrench. These models also have rear adjustable

rollers so you can align the refrigerator

with your kitchen cabinets. Use a 3/8" hex wrench with extension to turn the screws

for the rear rollers--clockwise to raise the

refrigerator, counterclockwise to lower it.

[] LEVEL THE DOORS

Rollers have three purposes:

• Rollers adjust so the door closes easily

when opened about halfway. (Raise the front about 5/8" [16 mm] from the floor.)

• Rollers adjust so the refrigerator is

firmly positioned on the floor and does

not wobble.

• Rollers allow you to move the refrigerator away from the wall for cleaning.

To adjust the rollers on 23" (33" wide), 25", 26", 27" and 29" models:

• Turn the roller adjusting screws

clockwise to raise the

refrigerator,

counterclockwise

to lower it. Use

a 3/8" hex socket _ []

or wrench, or an adjustable

wrench. Roller adjusting screw

Adjust the refrigerator door to make the doors even at the top.

To align:

[]

Using a 7/16" wrench, turn the door

adjusting screw to the right to raise the door, to the left to lower it.

NOTE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning

unless a wrench is used.

After one or two turns of the wrench,

[]

open and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

Installation Instructions

[] REPLACE THE BASE GRILLE

Replace the grille by installing the two Phillips head screws.

[] START THE ICEMAKER

Set the icemaker power switch to the

I (on) position. The icemaker will not

begin to operate until it reaches its operating temperature of 15°F (-9°C) or below. It will then begin operation automatically. It will take 2-3 days to

fill the ice bin.

Power

sw_tch

NOTE:

In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

[] SET THE CONTROLS

Set the controls to the recommended

setting.

5 5

Ill

[Ij

0 'p 18 REGOMMEN_ 3T ? 18 REGOMMEND_D

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER &DISPENSER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are

WX8X2, WX8X3 or WX8X4, depending on the

amount of tubing you need. Approved plastic

water supply lines are GE SmartConnect TM

Refrigerator Tubing (WX08X10002,

WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE

Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For

other reverse osmosis water systems, follow

the manufacturer's recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System

AND the refrigerator also has a water filter,

use the refrigerator's filter bypass plug. Using

the refrigerator's water filtration cartridge in conjunction with the RO filter can result in

hollow ice cubes and slower water flow from

the water dispenser. This water line installation is not warranted

by the refrigerator or icemaker manufacturer. Follow these instructions carefully to

minimize the risk of expensive water damage.

Water hammer (water banging in the pipes)

in house plumbing can cause damage to refrigerator parts and lead to water leakage

or flooding. Call a qualified plumber to correct

water hammer before installing the water

supply line to the refrigerator.

To prevent burns and product damage, do not

hook up the water line to the hot water line. If you use your refrigerator before connecting

the water line, make sure the icemaker power

switch is in the O (off) position. Do not install the icemaker tubing in areas

where temperatures fall below freezing. When using any electrical device (such as a

power drill) during installation, be sure the device is double insulated or grounded in a

manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with

local plumbing code requirements.

WHAT YOU WILL NEED

• Copper or GE SmartConnect TM Refrigerator

Tubing kit, 1/4" outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need:

measure the distance from the water valve on

the back of the refrigerator to the water supply pipe. Then add 8' (2.4 m). Be sure there is sufficient extra tubing (about 8' [2.4 m]

coiled into 3 turns of about 10" [25 cm] diameter) to allow the refrigerator to move

out from the wall after installation. GE SmartConnect TM Refrigerator Tubing Kits

are available in the following lengths: 2' (0.6 m) - WX08X10002

6' (1.8 m) - WX08X10006

15' (4.6 m) -WX08X10015

25' (7.6 m) - WX08X10025

Be sure that the kit you select allows at least

8' (2.4 m) as described above.

+ 94 hidden pages