GE Profile PT920SM, Profile PT920SMSS Datasheet

Listed by
Underwriters
Laboratories

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.

PT920SM

GE Profile™ 30" Built-In Single Convection Wall Oven

KW Rating

240V

4.5

208V

3.4

Breaker Size

240V

20 Amps

208V

20 Amps

Most 30” Wall Cabinets can be used with this unit.

Note: These ovens are not approved for stackable or
side-by-side installations. Cabinets installed adjacent

to wall ovens must have an adhesion spec of at least a
194°F temperature rating.

Door handle protrudes 3" from door face. Cabinets and
drawers on adjacent 45° and 90° walls should be placed
to avoid interference with the handle.

Electric wall ovens are not approved for installation
with a plug and receptacle. They must be hard wired
in accordance with installation instructions.

Installation Information: Before installing, consult

installation instructions packed with product for current
dimensional data.

Side-by-side installations require at least 2"
between cutouts.

C

L

2 x 4 or
equivalent
runners

Suitable

bracing

to support

runners

21-5/8"

over centerline

of cabinet

(must support 275 lbs.)

Cutout width
28-1/2'' MIN.
28-5/8'' MAX.

29-3/4

C

30

Recommended

cutout location

32-1/2"

from floor

21

Junction
box
location

Allow minimum of 21'' for clearance
to adjacent corners, drawers, walls, or etc.

Conduit

(72"
long)

5

27-1/4'' MIN.
27-5/16'' MAX.
Cutout height

A

B

23-1/2'' MIN.
Cutout depth

22'' MIN.

C

L

2 x 4 or
equivalent
runners

Suitable

bracing

to support

runners

21-5/8"

over centerline

of cabinet

(must support 275 lbs.)

Dimensions and Installation Information (in inches)

Specification Created 1/07

220239

Listed by
Underwriters
Laboratories

PT920SM

GE Profile™ 30" Built-In Single Convection Wall Oven

Note: 36” ribbon cooktops are approved for use
over GE 30” single wall ovens only. 30” ribbon
cooktops are approved for use over GE 30” and
GE 27” single wall ovens. Refer to cooktop and
wall oven installation information packed with
products for current dimensional data.

Note: CleanDesign or Sealed Burner Gas

This installation is to achieve minimum gap
between bottom of countertop and control
panel. For this installation, the bottom trim will
not be flush with a typical 4” toe kick

Note: Cabinets installed adjacent to wall ovens
must have an adhesion spec of at least a 194°F
temperature rating.

Installation Information: Before installing,
consult installation instructions packed with
product for current dimensional data.

Power cord
for cooktop

Junction box
for oven

Junction box in
adjacent cabinet
for cooktop
hook-up

2 (two) 90°elbows &
sufficient pipe to
connect in adjacent
cabinet

Right cabinet side

3/4" Support

Shut-off

valve

Pressure
regulator

1/2" Black

iron pipe

Union

Conduit

(72" long)

30" built-in

oven

3-1/2" MIN.
Free space

4" To 4-1/2"

3-1/4

22

Side View

With 36" Gas Cooktop

With 30" CleanDesign or Sealed Burner Gas Cooktop

5-9/16"

Reference dim.
for MAX. support
height with typical

36" countertop

height

36" Typical
Countertop height

Power cord

Reference
5-9/16

30-7/16

Free space

1-1/2" MIN.

1-1/2" Typical countertop

Side View

22

27-5/16" MAX.

Cutout height

27-1/4" MIN.

Junction box(s) for

oven & radiant

cooktop 22" from

floor

Add suitable

filler to match

adjacent cabinets

when needed

to maintain toe

kick alignment

30" Oven W/ Rad. Cktp.

5

24

25

Gas or electric cooktops may be installed

over this oven. See cooktop installation

instructions for cutout size. See label on

top of oven for approved cooktop models.

Gas (including the pressure regulator) and
electrical connections for gas cooktop must
be located in an adjacent accessible location.
For a 30" gas cooktop, the connections are
more conveniently made to the right.

120 Volt
Outlet

Gas
connection

Junction box
location
240/208V

36'' MIN.

4'' To 4-1/2 '' Toe kick allowable

Match toe kick height
front and two sides

22'' MIN. above
support platform

Top and/or side
fillers may be
necessary if unit
is positioned
between
existing cabinets

28-1/2'' MIN.
28-5/8'' MAX.

3/4'' Support
platform required

23-1/2" MIN.
Cutout depth

Allow 11/16''
overlap over side
edges of cutout

1-1/2"
Countertop

27-1/4'' MIN.
27-5/16'' MAX.
Cutout height

Specification Created 1/07

220239

Optional Undercounter Dimensions and Installation Information

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.