GE PROFILE PGP989DN/TN, Profile PGP989DNBB, Profile PGP989TNWW Dimensions And Installation Information

Dimensions and Installation Information

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.

Listed by
Underwriters
Laboratories

Specification Revised 4/09

230284

*Note: A 5" minimum spacing to adjacent side wall is required

Dimension and installation information are shown in inches.

Wall Installation: Wall installations require 25”
countertop

depth. When cabinet is flush against
the wall, the fan housing can be rotated to the
horizontal position for direct venting through
rear wall. Make a countertop cutout in the
range cabinet according to unit dimensions
and installation type. Duct hole is positioned in
back of cabinet for through-the-wall ducting.
Requires special offset adapter JXRW89.

Peninsula or Island Installation: For peninsula/
islands a minimum 26”

countertop

depth is suggested.
Blower should be in vertical position. Island or
peninsula cabinets may require adjustment in cutout
depth and/or location within the width dimensions.
Duct hole is positioned in bottom of cabinet for island
or peninsula installation.

Slab Installation: For peninsula or island installation
and rear wall ducting, 6” PVC duct or locally

approved piping should be used if installing under
a poured concrete slab.

Installation Information: Before installing, consult

installation instructions, packed with product, for
current dimensional data.

Note: These cooktops are approved for indoor use only.

40

Long

20

9

4

10-1/2

16

C
L

Cabinet Dimensions (in inches)

227⁄16ʺ

(229⁄16ʺ SS)

201⁄2ʺ

22ʺ

297⁄8ʺ

(30ʺ SS)

23⁄16ʺ

(21⁄4ʺ SS)

283⁄4ʺ

PGP989DN/TN

GE Profile™ 30" Downdraft Gas Cooktop

227⁄16ʺ

(229⁄16ʺ SS)

201⁄2ʺ

22ʺ

297⁄8ʺ

(30ʺ SS)

23⁄16ʺ

(21⁄4ʺ SS)

283⁄4ʺ

25

1-7/8"

MIN. Required*

20-5/8

Cut-out Dimensions (in inches)

28-7/8

*U.L. Requirement.

Note: A 5" minimum spacing to adjacent side wall is required

Dimensions and Installation Information

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.

Dimension and installation information are shown in inches.

Listed by
Underwriters
Laboratories

Specification Revised 4/09

230284

Installing the Ductwork: Use galvanized
or aluminum duct in 6” round or 3-1/4” x
10” size, or combination of both. PVC duct

or locally approved piping should be used
if installing under a poured concrete slab.

Local building code must be followed in
specifying type and schedule of all duct used.

Note: Ductwork must be vented to outside.
Do not vent into a wall, ceiling, crawlspace,
attic or any concealed space. Always use
an appropriate roof or wall cap with damper.

Laundry-type wall caps should never
be used. For maximum efficiency use the

shortest and straightest duct run possible,
with as few fittings as possible.
For satisfactory

performance the duct run
should not exceed 100 feet equivalent length.
Refer to the table of equivalent lengths
(shown in installation instructions) for
various duct configurations.

Rear Wall VentingDownward Venting

Venting Options

Through Cabinet Toe Space

Inside Wall to Roof Direct to Outside

Between Floor Joist

9-1/8

10-1/8

18-3/4

6-1/8

PGP989DN/TN

GE Profile™ 30" Downdraft Gas Cooktop