GE Profile PSW26LSRSS, Profile ENERGY STAR PSW26LSR Dimensions And Installation Information

R

Listed by
Underwriters
Laboratories

R

"94 SxS Refer

A

Front View

Top View

G

D

C

F

B

E

H

PSW26LSR

GE Profile™ ENERGY STAR® 25.6 Cu. Ft. Stainless-Wrapped Side-By-Side Refrigerator

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.

Dimensions and Installation Information (in inches)

As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.

210335

Specification Created 3/05

Overall

Dimensions

Height to top of hinge (in.) A 70-1/2*

Height to top of case (in.) B 70-1/2

Case depth without door (in.) C

†

28

Case depth less door handle (in.) D

†

32-1/4

Case depth with door handle (in.) E

†

34-7/8

Depth with fresh food door open 90° (in.) F

†

50-1/16

Width (in.) G

35-3/4**

Width with door open 90° with door handle (in.) H 42-3/8

Air

Clearances

Each side (in.)

1/8

Top (in.)

1

Back (in.)

1

*When cap is removed: 69-1/4"
**Width including top caps is 35-7/8".
† Water hook-up fits in back air clearance when calculating

installation depth.

If installed against a wall, allow clearance of 14-3/16" on freezer
side to remove bin.

Clearance required to remove fresh food full-size pan without
disassembling is 18-15/16".

Allow additional space for any necessary leveling adjustments.

As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.

R

Listed by
Underwriters
Laboratories

R

PSW26LSR

GE Profile™ ENERGY STAR® 25.6 Cu. Ft. Stainless-Wrapped Side-By-Side Refrigerator

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.

To Remove Top Caps and Doors on PSW26LSR

Step 1: the refrigerator. Remove two screws, one on each side at the rear of the top
cap. Lift off and remove top cap.

Step 2: Open both doors. Remove one screw on each side of the toekick. Pull forward
to remove toekick.

Step 3: On the freezer door, disconnect water line coupler by pushing against the
collar on the left side. Disconnect wire harness.

Step 4: Use a Torx T-20 screwdriver to remove 2 screws holding the top hinge.
Carefully remove hinge while supporting door. Lift door up and off bottom hinge.
Remove fresh food door in the same manner. Note: Do not remove bottom hinges!
Door alignment will be difficult if bottom hinges are removed.

Step 5: Place refrigerator onto a hand truck, upright and against one side.
Move refrigerator to the installation location.

Step 6: Carefully lower doors onto bottom hinges. Be sure to route the tubing and
electrical connector through the bottom hinge. Reinstall top hinges.

Step 7: Place cap over the top of the refrigerator. Reinstall the original screws in the
top and back of the cap.

Step 8: Reconnect the wiring harness and waterline.

210335

Specification Created 3/05

Water Line Coupler

1.

Hinge Screws

Wire Harness

Toekick Screw

4.

3.

2.