GE Profile Arctica CustomStyle PSW23PSR, Profile Arctica CustomStyle PSW23PSRSS Dimension Manual
PSW23PSR – GE Profile Arctica CustomStyle™ ENERGY STAR® 22.6 Cu. Ft. Stainless-Wrapped
Side-By-Side Refrigerator with Dispenser
TM
Specification Revised 7/ 04
210265
Dimensions (in inches)
"94 SxS Refer
A
Top View
G
D
C
F
B
E
H
*Width including top caps is 36-3/16".
† Water hook-up fits in back air clearance when calculating installation depth.
If installed against a wall, allow clearance of 13-15/16" on freezer side to
remove ice bin.
To remove fresh food pans, remove door bins.
Clearance required to remove fresh food full-size pan without disassembling:
18-5/8
".
Plus, allow additional space for any necessary leveling adjustments.
Overall
Dimensions
Height to top of hinge (in.) A
69-1/4*
Height to top of case (in.) B
68-3/4
Case depth without door (in. ) C
†
23-7/8
Case depth less door handle (in.) D
†
26-3/4
Case depth with door handle (in.) E
†
29-3/16
Depth with fresh food door open 9 0° (in.)
F
†
45-9/16
Width (in.) G
35-3/4*
Width with door open 90° with door handle (in.) H
38-3/16
Air
Clearances
Each side (in.)
1/8
Top (in.)
1
Back (in. )
1/2
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE
®
appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
R
Total volume and shelf
area are calculated by
the Association of Home
Appliance Manufacturers’
standards.
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR
guidelines
for energy efficiency.
PSW23PSR – GE Profile Arctica CustomStyle™ ENERGY STAR® 22.6 Cu. Ft. Stainless-Wrapped
Side-By-Side Refrigerator with Dispenser
TM
Specification Revised 7/ 04
210265
Water Line Coupler
1.
Hinge Screws
Wire Harness
Toekick Screw
4.
3.
2.
To Remove Top Cap and Doors on PSW23PSR
Step 1: Locate and remove two Phillips head screws on the top of
the refrigerator. Remove t wo screws, one on each side at the
rear of the top cap. Lift off and remove top cap.
Step 2 : Open both doors. Remove one screw on each side of the
toekick. Pull forward to remove toekick.
Step 3 : On the freezer door, disconnect water line coupler by
pushing
against the collar on the left side. Disconnect
wire harness.
Step 4 : Use a Torx T-20 screwdriver to remove 2 screws holding the
top hinge. Carefully remove hinge while supporting door.
Lif t door up and off bottom hinge. Remove fresh food door in
the same manner. Note: Do not remove bottom hinges! Door
alignment will be difficult if bottom hinges
are removed.
Step 5 : Place refrigerator onto a hand truck, upright and against one
side. Move refrigerator to the installation location.
Reinstall Doors, Top Cap
Step 6 : Carefully lower doors onto bottom hinges. Be sure to route
the tubing and electrical connector through the bottom
hinge. Reinstall top hinges.
Step 7: Place cap over the top of the refrigerator. Reinstall the
original screws in the top and back of the cap.
Step 8 : Reconnect the wiring harness and waterline.
R
Listed by
Underwriters
Laboratories
For answers to your Monogram,® GE Profile™ or
GE
®
appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center
®
service, 800.626.2000.
R
Total volume and shelf
area are calculated by
the Association of Home
Appliance Manufacturers’
standards.
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR
guidelines
for energy efficiency.
Loading...