GE Profile Advantium JX2201NSS, Profile Advantium PSB1201NSS, PSB120 - Profile Advantium: 120V Dimensions And Installation Information

Specification Created 11/08

240 446

Listed by
Underwriters
Laboratories

PSB1201NSS

GE Profile Advantium® 120 Volt - 30" Wall Oven

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,

800.626.2000.

C

L

(Must support 130 lbs.)

2 x 4’s or
equivalent
solid floor

Suitable

bracing

to support

runners

21-5/8"

over centerline

of cabinet

Cabinet

Width

(inches)

W

WidthH Height

D

Depth

(excluding

handle)

X

Cutout

Width

Y
Cutout
Height

Z
Cutout
Depth

(minimum)

PSB1200/1 with out
accessory drawer

30 29-25/32 19 -1 /8 21-3/4 25-1/8 17-1 /2 23 -1 /2

PSB1200/1 with
accessory drawer

30 29-25/32 2 2-1/ 4 21-3/4

25-1/4 to

28 -1 /2*

21 23 -1/ 2

*For existing cutouts a maximum width of 28-1/2" is acceptable

Advantium wall oven/GE Profile cooking tower dimensions and cabinet installation information (in inches)

Note: 2" minimum

between cutouts when
installed above warming
drawer or single wall oven.

Installation Information:
Before installing, consult
installation instructions
packed with product for
current dimensional data.

Note: PSB1200/1 series
Advantium can be
installed below GE/GE
Profile non-downdraft
gas and electric cooktops.
It CANNOT be installed
below induction or Monogram
(2GU3841385) gas cooktops.

Note: PSB1200/1 series Advantium
oven comes with two lower trim pieces.
One is for use above 36-inch height
installations and one is for use below 36­inch installations. Use of the accessory
drawer will replace the bottom trim piece
for applicable installations. Please see
installation instructions for full details.

1" Min. above toeki ck or adjust
to oven in stallation height

2" MIN between cutouts

2-1/2" MIN bet ween cutouts
recommended—2" MIN req uired

9-1/4" cutout heig ht
28-1/2" cutout wid th

Junction box location

A

B

A

B

Construct Solid Bo ttom
MIN 3/8" Plywood S upported by
2 x 4 or 1 x 2 R unners, all Four Sides.
(Must Suppor t 150 lbs. for Advantium)
(Must Suppor t 200 lbs. for Wall Oven)

4-3/16

D

Excluding

Handle

H

W

Conduit

(46" long)

Cabinet width

(240-volt models o nly)

4-3/16"

23-1/2"

Cutout depth

Junction
box location

17-1/2"

Cutout height

29-25/32"

19-1/32"

21-1/2"

Excluding

Handle

Conduit

(48-1/2"

long)

B

30"

5" min.from
floor 1" min.

above toekick

A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.

Construct Solid
Bottom Min.
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)

A

4-3/16"

23-1/2"

Cutout depth

A= Allow 1" overlap of oven over bottom edge of cutout, and allow
1-1/4" overlap at top edge of cutout.
B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.

Advantium Wall Oven Dimensions (in inches)and
Cabinet Installation (in inches)

Note: Cabinets installed adjacent

to wall ovens must have an adhesion
spec of at least 194° F temperature rating.

Specification Created 11/08

240 446

Listed by
Underwriters
Laboratories

PSB1201NSS

GE Profile Advantium® 120 Volt - 30" Wall Oven

Installation over a GE/Monogram
Warming Drawer:

30”

23-1/2”

25-1/4”

Min.

21”

2” Min.
(3” recommend ed)

Per w arming
drawer
requir ement

Construct
Solid Bo ttom
Min. 3/8 ”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sid es

5” mi n.

from floor

1” mi n.
above
toeki ck

Warming Drawer:

Construct S olid
Bottom Min.
3/8” Plyw ood
Supported by
2x4 or 2 x2
Runners a ll
Four Side s

30”

23-1/2”

21”

2” Min.

Per Oven
Requirement

Per warmi ng drawer requirement

2” Min.
(3” recommen ded)

25-1/4”

Min.

5” mi n.

from floor

1” mi n.

above

toeki ck

Prepare the opening (cont.)

When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium and the other appliance overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.

• the support must be level and rigidly

mounted, flush with the bottom edge of
the cutout.

Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.

Installation over a GE/Monogram Oven
and Warming Drawer:

Note: Additional clearances between the

cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30­pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.

Preparation WITH an Accessory Drawer

Prepare the opening

The Advantium PSB1200/1 series can be installed in combination with
other GE/Monogram appliances. Always follow each product's Installation
Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall to the
dimensions shown.

* For existing cutouts, a maximum

width of 28-1/2" is acceptable. If
the opening is slightly wider, secure
a furring strip on each side of the
cutout for securing the oven.

• Allow 3/4" to 2-1/8" case trim overlap
on the sides and 7/8" overlap on the
bottom of the opening for all models.
The amount of overlap on the sides
depends on the actual cutout width.
Allow 1-1/4" case trim overlap on the
top for models PSB1200 and PSB1201
and for models ZSC1201 and ZSC1202.

• Oven overlaps will conceal cut edges on all sides of the opening.

Note: PSB1200/1 series Advantium can be installed below GE/GE Profile
non-downdraft gas and electric cooktops. It CANNOT be installed below
induction or Monogram (2GU3841385) gas cooktops.
Note: PSB1200/1 series Advantium oven comes with two lower trim
pieces. One is for use above 36-inch height installations and one is for
use below 36-inch installations. Use of the accessory drawer will replace
the bottom trim piece for applicable installations. Please see installation
instructions for full details.

30”

23-1/2”

25-1/4”

Min.

21”

Construct
Base
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides

5” mi n.

from floor

1” mi n.

above
toeki ck

For answers to your Monogram,® GE Profile™ or GE®
appliance questions, visit our website at ge.com or
call GE Answer Center® service, 800.626.2000.