GE PGP989DNBB User Manual
40
Long
Cabinet Dimensions (in inches)
PGP989DN/TN
227⁄16ʺ
(22
9
⁄16ʺ SS)
201⁄2ʺ
22ʺ
297⁄8ʺ
(30ʺ SS)
23⁄16ʺ
(2
1
⁄4ʺ SS)
283⁄4ʺ
Cut-out Dimensions (in inches)
GE Profile™ Series 30" Downdraft Gas Cooktop
Dimensions and Installation Information
Wall Installation: Wall installations require 25”
countertop
the wall, the fan housing can be rotated to the
depth. When cabinet is flush against
horizontal position for direct venting through
rear wall. Make a countertop cutout in the
range cabinet according to unit dimensions
and installation type. Duct hole is positioned in
back of cabinet for through-the-wall ducting.
Requires special offset adapter JXRW89.
Peninsula or Island Installation: For peninsula/
islands a minimum 26”
countertop
depth is suggested.
Blower should be in vertical position. Island or
peninsula cabinets may require adjustment in cutout
depth and/or location within the width dimensions.
Duct hole is positioned in bottom of cabinet for island
or peninsula installation.
Slab Installation: For peninsula or island installation
and rear wall ducting, 6” PVC duct or locally
approved piping should be used if installing under
a poured concrete slab.
Installation Information: Before installing, consult
installation instructions, packed with product, for
current dimensional data.
Note: These cooktops are approved for indoor use only.
20-5/8
*U.L. Requirement.
Note: A 5" minimum spacing to adjacent side wall is required
25
1-7/8"
MIN. Required*
227⁄16ʺ
9
(22
⁄16ʺ SS)
201⁄2ʺ
28-7/8
22ʺ
16
297⁄8ʺ
(30ʺ SS)
283⁄4ʺ
9
20
C
L
23⁄16ʺ
1
(2
⁄4ʺ SS)
4
10-1/2
For answers to your Monogram® or GE® appliance
questions, visit our website at geappliances.com
or call GE Answer Center® service, 800.626.2000.
*Note: A 5" minimum spacing to adjacent side wall is required
Dimension and installation information are shown in inches.
Listed by
Underwriters
Laboratories
Specification Revised 3/13
230284
Venting Options
Through Cabinet Toe Space
Inside Wall to Roof Direct to Outside
Between Floor Joist
PGP989DN/TN
GE Profile™ Series 30" Downdraft Gas Cooktop
Dimensions and Installation Information
Installing the Ductwork: Use galvanized
or aluminum duct in 6” round or 3-1/4” x
10” size, or combination of both. PVC duct
or locally approved piping should be used
if installing under a poured concrete slab.
Local building code must be followed in
specifying type and schedule of all duct used.
Note: Ductwork must be vented to outside.
Do not vent into a wall, ceiling, crawlspace,
attic or any concealed space. Always use
an appropriate roof or wall cap with damper.
Laundry-type wall caps should never
be used. For maximum efficiency use the
shortest and straightest duct run possible,
with as few fittings as possible.
For satisfactory
should not exceed 100 feet equivalent length.
Refer to the table of equivalent lengths
(shown in installation instructions) for
various duct configurations.
performance the duct run
10-1/8
6-1/8
9-1/8
18-3/4
Rear Wall VentingDownward Venting
Dimension and installation information are shown in inches.
Specification Revised 3/13
230284
Loading...