39-3/4"
PFDS450GL/PFDS455GL
2-1/2
12
Connection
Connection
GE Profile™ Series 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Dimensions and Installation Information (in inches)
Gas Dryer Rating
120V
60Hz, 6A
Exhaust Options: 3-way via rear, right, and bottom.
Circuit Requirements: An individual, properly grounded
branch circuit, protected by a 30-amp circuit breaker or
a time-delay fuse, is required.
LP Conversion Kit: WE25M46
Note: Dryer wall outlet must be located within 36”
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete information, see
installation instructions packed with your dryer.
34 3/8"
27"
RY
D
EMP
T
34 3/8"
39-3/4"
4-1/8"
3"
For answers to your Monogram,® Profile™
Series or GE® appliance questions, visit our
website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
1-3/4
Gas Pipe
3-1/2
Electrical
Specification Revised 3/13
270184
PFDS450GL/PFDS455GL
GE Profile™ Series 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Special Installation Requirements:
Stacked Installation:
• Brackets for stacking dryer over washer are available at an additional cost.
Custom built-in white installation template:
• Order Pub. No. 14-A025.
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
• Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223
for gas dryers.
Minimum Clearance other than Alcove or Closet Installations:
• Minimum clearances to combustible surfaces 0" both sides, 3" rear.
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
For answers to your Monogram,® Profile™
Series or GE® appliance questions, visit our
website at geappliances.com or call GE
Answer Center® service, 800.626.2000.
Stacked Dimensions (in inches)
Storage Pedestal Dimensions
(in inches)
SPSD157JMG - Champagne
SPSD157JWW - White
This optional 15" pedestal raises
the door opening and height of
the washer or dryer. Feet on 15"
pedestal allow it to adjust to 153/8" height.
27
79 1/2"
29-1/2
15
Specification Revised 3/13
270184
PFDS450GL/PFDS455GL
GE Profile™ Series 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4” diameter
all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible
metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may
be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can
be maintained throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible metal
(foil type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire
hazard or moisture could cause damage. Never terminate the exhaust into a common duct
or plenum with a kitchen exhaust, since the combination of lint and grease could create a
fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
A
4
Domestic
dryer models
7.5 cu. ft.
capacity electric
and gas dryers
A
B
2-1/2
Number
90°
turns
of
0
1
2
3
4
Best performance
Maximum length of 4"
dia. rigid metal duct
Exhaust hood type
A
4"
opening
150 ft.
140 ft.
130 ft.
120 ft.
110 ft.
B
2-1/2"
opening
127 ft.
117 ft.
107 ft.
97 ft.
87 ft.
Specification Revised 3/13
270184
PFDS450GL/PFDS455GL
GE Profile™ Series 7.5 cu. ft. stainless steel capacity frontload dryer with Steam
Features and Benefits
• Steam Refresh/Steam Dewrinkle - Steam Refresh helps reduce wrinkles, odors
and rejuventates fabrics, while Steam Dewrinkle reduces wrinkles and freshens
clean clothes
• Duo Dry system - Dual motors, dual moisture sensors and dual thermistors
continually monitor air temperature to provide even heat for optimal drying
performance and a variable heater delivers constant heat, eliminating extreme
temperature changes
• eDry option - Energy-saving option reduces dry temperatures on select cycles
without sacrificing performance
• Specialty cycles - Pre-set cycles take specific care of 24 types of specialty loads
including performance fabrics, fleece, pet bedding, and bras and hosiery
• Baffle Dry system - Built-in dryer rack and hanger clip design adds drying
options for hard-to-dry items and delicates
• Clean Speak communication system - The washer communicates electronically
with the dryer to preset dry cycles and help save time
• Speed Dry - Quickly dries items and small loads for families on the go
• Up to 150 ft. venting capability - 150 ft. equivalent venting provides flexible
installation
• ADA Compliant
• Model PFDS455GLMG – Champagne
• Model PFDS455GLWW – White
Specification Revised 3/13
270184
Loading...